Search Documents

By H. Doi, Y. Fujiwara, K. Miyake

In order to throw light on the mechanism of plastic deformation of WC-Co alloys, compressive tests of WC-(7 to 43) vol pct Co alloys have been carried out at room temperature, and stress-micro strain relation has been investigated in detail. The analysis of the factors affecting the yield stresses reveals that the yield stresses can be predicted by modified Oro-wan's theory if one properly estimates the planar in-terfiarticle spacings. Conzpressive straining of some of the alloys by 0.066 to 0.17pct increases the decrements by a factor of as much as 3.4 to 14, whereas the corresponding increase in the electrical resistivities is less than 10 pct. The analysis of the decrement data in terms of -Gramto and Lücke theory shows that the marked increase is attributed to increased dislocation darnping itt the binder (cobalt) phase. By cornbilling the decrement data and the conzjwession duta, one obtains the relation between flow stress in shear (?t) and increase in dislocation density (p): At = const . v6 . This is interHeted to mean that the mechanism of strain hardening of CirC-Co alloys is essentially sarne as the one for dispersion strengthened alloys. The possible effect of bridge formations between the carbide particles has also been examined. OWING to the combination of hardness, strength, and other physical and chemical properties, WC-Co alloys have opened the way for unique fields of applications, the recent ones being, for instance, anvils for super-high-pressure generation apparatuses. In such applications, the alloys are frequently subjected to very high compressive stresses: these stresses may cause the alloys to deform plastically and eventually to fail. However, much remains obscure regarding the nature of the plasticity of the alloys. Evidently, the alloys owe their high strength to the hard carbide particles which frequently occupy as much as 80 to 90 pct in volume fraction, whereas the ductility required for practical applications is provided by the small amount of the binder phase between the carbide particles. When the volume fraction of the carbide phase is not very large, deformation behavior of the alloys may be described by some of the current dispersion strengthening theories. However, greatly increasing the carbide phase is thought to lead to some carbide skeleton structure or bridge formations owing to the increased chances for direct contacts between the carbide particles;1,2 this may appreciably affect the plasticity of the alloys. Regarding the effect of formation of the carbide skeleton structure, it is interesting to note the work by Ivensen et al.3 on compression tests of the alloys containing somewhat large carbide particles; they observe extensive generation of slip bands in the carbide particles after application of some preliminary compressive stresses. They interpret the results in terms of plastic deformatiot: of the carbide particles which are supposed to have formed a skeleton structure; the binder phase plays only a passive role, at least in the early stages of the deformation. That carbide crystals exhibit microplasticity at room temperature is apparent from the work of Takahashi and Freise4 and French and Thomas5 on indentation of WC single crystals. On the other hand, Dawihl and coworkers6-10 maintain that even when volume fraction of the carbide phase is very large (for instance, more than 90 pet), a very thin binder layer generally exists between the carbide particles. They interpret the results of the extensive mechanical tests in terms of the plasticity of such a layer. Gurland and Bardzil11 point out that decrease in ductility of the alloys with increase in the carbide phase is caused by the effect of plastic constraint exerted by the dispersed carbide particles. Drucker12 further develops this concept from a continuum-mechanics approach on an assumption that a continuous thin binder layer separates the carbide particles. A common feature of the studies reported so far on the plasticity of the alloys is that the information deduced is invariably qualitative in nature. Thus, very few systematic experiments for obtaining reliable and sufficiently detailed stress-strain curves of the alloys varying widely in the microstructural features have been carried out. In particular, it may be of special interest to investigate in detail the early stages of the plastic deformation of the alloys in order to shed light on the strengthening mechanism. However, such work appears to be extremely rare. Doi et al.13 recently reported a first brief account of the results of some quantitative analysis of the plasticity of the alloys in terms of dislocation theory. Their experiment was rather limited in the composition range covered (volume fraction occupied by the carbide phase: 79 to 83 pct), and thus they could not necessarily elucidate the controlling mechanism of plastic deformation of the alloys of a more general composition range. Consequently, in the present investigation, deformation behavior and some other physical properties of the alloys were investigated and discussed in more detail over a much wider composition range. SPECIMEN PREPARATION WC-Co alloys used in this experiment were prepared in cylindrical or rectangular form by sintering in vacuo compressed mixtures of tungsten carbide and cobalt

Jan 1, 1970

By Leon Eliel

TEN years ago a broad knowledge of aerial mapping, coupled with a smattering of geology, qualified one to speak on the subject of the appli-cation of aerial mapping to geology. Today, with aerial maps a common tool in the hands of expert geologists on every continent throughout the world, it would be nothing short of presumptuous for the author of this paper, who is not a geologist, to give any geological statements on his own authority. Relatively, today we are only purveyors of general geological gossip, with a definite case here and there by way of illustration. But we can present a story of the really marvellous strides that have been made in the evolution of aerial mapping, built around a skeleton of geological tidbits, from which some useful conclusions may be drawn. The average geologist goes about reading his aerial maps much as one would approach the problem of deciphering a cryptogram. To begin with, typical key expressions appear in recurring sequences and under certain conditions. If once the meaning of these isolated bits of infor-mation can be ascertained, the message begins to take meaning. In a similar fashion, the geologist works out his key from aerial maps of territory with which he has some familiarity. He learns that a certain type of thin, white line may mean a vein of quartz. He sees that a certain change in the photographic tone of vegetation on the ground reflects two kinds of soils on opposite sides of, a contact. He sees that a certain type of alignment of topographical features often means a fault. He learns that by the erosion pattern .he can frequently distinguish soft formations from harder ones. And so, bit by bit, he ties together the information of the picture with his experience on the ground until he develops a reasonably creditable capacity of interpretation. Through the complete gamut of surface conditions, ranging all the way from flat, arid, exposed desert terrain to dense jungle, or rugged mountains, the evidence from which the geologist must make his inter-pretation varies with bewildering profusion. The quality of photographs which are obtainable may range from perfect pictures in the desert to almost useless smudges in the steaming jungles. One thing he has learned with certainty-the airplane carrying its mapping camera is a superb reconnaissance tool, only awaiting his ingenuity in correlating the pictures with the ground to simplify most exploratory problems.

Jan 1, 1936

By D. Dever, E. S. Fisher

Measurements of the temperature dependence of the elastic moduli in single crystals of hep ruthenium, rhenium, cobalt, dysprosium, and erbium were carried out for various temperature ranges so as to investigate the correlation, suggested by prior work, between the shear anisotropy ratio, A = C44/C66, and the occurrence of the hcp — bee phase transformation. These measurements confirm the suggestion that A has a positive temperature dependence in that group of hcp metals that undergo thermally induced transfornzations to the bee structure and a negative or zero temperature dependence in the other hcp metals. It appears, from indirect evidence, that the hcp -fee transformation in cobalt is preceded by a highly negative temperature dependence of A. These results indicate that elastic anisotropy is an important factor in determining the temperatures at which martensitic phase transformations occur. Two possible roles for elastic anisotropy are proposed: 1) the shear-modulus ratio within the habit planes must be nearly similar for the two phases and 2) a large anisotropy decreases the stress necessary for the movement of the transfornzation dislocations. FUCHS' calculations of the elastic moduli in the alkali metals have shown that the high shear-anisotropy ratios, c/c', in certain bee metals and alloys are the result of large negative contributions to c' = (c11 - c12)/2 arising from the nearest-neighbor repulsive forces.' On this basis, and following Zener,2 the association between high c/c' ratios and the martensitic phase transformations that occur upon cooling certain bee metals is explained as a unique characteristic of the bee structure. Recent measurements of the elastic moduli in hcp titanium and zirconium show, however, that a high elastic anisotropy also exists in these hcp structures at the temperatures at which they transform to bee upon heating3. If there exists a direct and consistent correlation between the elastic anisotropy in close-packed structures and the occurrence of transformations to the bee phases then there is evidently a need to re-examine the conclusions of Zener theory. Elastic anisotropy may also be the result of the effects of temperature on the stability of the low-temperature close-packed structures or it may play an important role in the mech- anism of the martensitic transformations. The present measurements were aimed at establishing the phenomenological correlation between elastic shear anisotropy in hcp structures and the thermally induced hcp —bee transformations that occur in the majority of the twenty-three hcp metals, as shown in Table I. Prior to the present work the temperature dependence of the anisotropy ratio, A = c44/c66, was known at various temperatures for nine of the metals listed. The data showed a negative temperature dependence of A for cadmium, zinc, magnesium, and cobalt, which do not transform to bee, and a positive temperature dependence of A for thallium, zirconium, titanium, hafnium, and yttrium. The correlation was, however, ambiguous in that these two groups of metals are also separated with respect to the c/a ratios as noted in Table I. There remained the possibility that the temperature dependence of A is a function of c/a and not consistently associated with the transformation. The measurements of the elastic moduli in rhenium and ruthenium, in which hcp —bee transformations do not occur, were needed to help decide this question. The studies of dysprosium and erbium were undertaken to determine whether the correlation holds for the heavy rare earth metals.

Jan 1, 1968

By P. F. Gnirk, J. B. Cheatham

Single bit-tooth penetration experiments under static load were conducted on six rocks at confining pressures of O to 5,000 psi using sharp wedge-shaped teeth with included angles ranging from 30 to 120° In general, the force-displacement curves for all rocks exhibit an increasingly nonlinear and discontinuous behavior with decreasing confining pressure. The confining pressure at which a rock exhibits a macroscopic transition from predominantly ductile to predominantly brittle behavior during penetration vmies from about 500 to 1,000 psi for the limestones to greater than 5,000 psi for dolomite. The correlation between calculated values of force per unit penetration based on plasticity theory and experimental values is quite encouraging, even at confining pressures as low as 1,000 psi A qualitative correlation between volume of fragmented rock per unit energy input for a single bit-tooth and drilling rate for microbits appears to exist over a confining pressure range of 0 to 5,000 psi. INTRODUCTION Laboratory experiments utilizing a small-scale drilling apparatus have demonstrated that penetration rates are reduced considerably as a result of increasing the confining pressure from atmospheric to a few thousand psi?-3 This undesirable situation can, in general, be attributed to a combination of decreased efficiency of chip removal at the bottom of the borehole, increased rock-failure strength, and a possible change in the mechanism of chip generation and rock fragmentation with increasing confining pressure. To more fully understand the principles underlying the last circumstance, it is the purpose of this investigation to experimentally study the mechanism of single bit-tooth penetration into dry rock at low confining pressures and, in particular, to establish the confining pressure at which the penetration mechanism may undergo a brittle to ductile transition for various rock types commonly encountered in drilling. Confining pressure as used here refers to the differential pressure between the borehole fluid pressure and the formation-pore fluid pressure. EXPERIMENTAL PROCEDURE Using an experimental apparatus previously described: a single, sharp wedge-shaped tool was forced under a "statically" applied load into an effectively semi-in finite dry rock sample subjected to a prescribed confining pressure. To prevent the invasion of the con fining-pressure fluid into the pores of the rock sample during penetration, the exposed surface of the rock was jacketed with a layer of silicon putty.* Electrical instrumentation incorporated into the apparatus yielded a graphical plot of force on the tool as a function of penetration or displacement of the tool into the rock during an experiment. During the course of the experimentation the following conditions were maintained constant: (1) pore pressure — atmospheric (i.e., the rock was dry); (2) temperature — 75F; (3) rate of loading — essentially static (approximately 0.002 in./sec); (4) bit tooth — a sharp wedge-shaped tool loaded normal to the rock surface; (5) rock surface — smooth and flat; (6) drilling fluid — hydraulic oil; and (7) maximum depth of penetration — approximateiy 0.1 in. In addition, each experiment was performed on a different rock sample so the rock surface is free of a layer of cuttings and of any previous indentation craters. The influence of the corners of a borehole was neglected, since each rock sample was cemented inta a section of aLuminum tubing to simulate a semi-infinite body. Indentation experiments were made on a sandstone, two limestones, a marble, a dolomite and a schist with a 60' bit-tooth over a range of confining pressures from atmospheric to 5,000 psi and at a constant confining pressure of 1,000 psi for a variety of bit-teeth with angles ranging from 30 to

Jan 1, 1966

By Victor A. Phillips

A series of strips of a Ni-12.7 at. pct A1 alloy were Prepared containing cubical y'(NisAl) precipitates with edge lengths from 60 to 500A. A particle-free solution-tveated strip was included for cornparison. They weve cold-rolled 95 pct and the effects of particle size on the isochronal (1/2 hr) annealing behavior between 300° and 950°C studied (by hardness and light and electron microscopy). It ulas inferred that the particles deformed with the lnatvix becoming lamellae which remained coherent. Comparison with published data fov pure nickel showed that aluminum greatly re-tavded softening and recrystallization, but it made little difference whether or not particles were present. The presence of pakticles led to a heterogeneous distribution of precipitates after annealing at 700" to 750°C. Recovery was not detected. Recrystallization occurred by the growth of new grains into unrecrys-tallized material. In a previous study by the author,' the growth of Ll2-type ordered yl(Ni3Al) precipitates was followed in Ni-12.7 at. pct A1 alloy as a function of aging at 600" and 700°C. The particles were showo to be cubical in shape in all sizes from 50 to 3000A and remained coherent. This work was used as a guide in preparing the starting structures for the present study of the effect of these particles on the annealing behavior of heavily cold-rolled strip. Another question of present interest was whether dislocation and particle hardening were additive, since the structures before rolling ranged from solution-treated to peak-aged to overaged. Also, precipitation might occur on annealing after cold-rolling. Reference may be made to other papers2"5 for previous work in this relatively unexplored field and only some recent work will be mentioned her:. phillips2 studied the effect of deformable 0 to 590A-diam cobalt particles on a Cu-3.23 pct Co alloy rolled 95 pct and found that the particles, which rolled out into thin lamellae, impeded softening and recrystallization. Tanner and servi3 likewise studied the annealing of cold-swaged Cu-2 pct Co alloy containing 150A-diam particles and found impeding effects. Haessner et a1.,4 on the other hand, found that incoherent 2-p-diam non-deformable particles of B4C (0.04 vol pct) tended to increase the rate of recrystallization of copper rolled up to 95 pct reduction. They attributed this to the formation of new grains at the particle interfaces. Humphreys and artin' found that nondeformable silica particles in copper rolled to 30 pct reduction accelerated recrystallization if the particle spacing was large and retarded it if the spacing was smaller. Haessner et a1 4 also studied a rolled Ni-Cr-A1 alloy; however, the particles of y'(Ni3Al)-type precipitate were not put in before rolling, but separated during the isothermal annealing at 750°C. No previous work appears to have been carried out on the effect of y' (Ni3A1) particles on the annealing of Ni-A1 alloy. Hornbogen and ICreye7 redetermined the solubility c of aluminum in nickel as a function of temperature T and showed that it was given by c = 32.6 exp(-1940/RT). This relation gives aluminum solubilities of 15.1, 14.2, 12.0, and 10.7 at. pct at 1000°, 900°, 700°, and 600°C, respectively. The phase precipitated from the nickel-rich solid solution is fcc y1 (Ni3A1) which has a Cu3Au -type ordered structure8 and remains ordered up to 1000°C.B EXPERIMENTAL PROCEDURE The alloy used was identical with that used before. Chemical analysis showed 6.27 wt pct (12.71 at. pct) Al, the principle impurities being 0.065 pct Fe, 0.022 pct Co, 0.020 pct Cu, and 0.004 pct C. Bar stock of 1 in. diam was cold-swaged to % in. diam, cold-rolled to 0.300-in.-thick strip, and annealed at 900°C in dry hydrogen. It was cold-rolled to 0.100-in. thickness and solution-treated for 1 hr at 1000°C while sealed in a quartz tube in argon, quenching in iced brine with the aid of a device to snap off the nose of the tube. Lineal analysis gave an average grain size of 0.055 mm. Pieces of strip were aged at 700°C in vacuo for 30 min, 51/4 hr, and 1 week to produce nominal average particle widths of 60, 150, and 500A, respectively, as known from the previous work.' The average diamond pyramid hardness was determined. The heat-treated strips were rolled from 0.100 to 0.005 in., a reduction of 95 pct, and the rolled strips stored at about -5°C. Small pieces were annealed within 1 week for 30 min at temperatures from 300° to 950° ±2°C in a horizontal vacuum furnace. Strips were withdrawn into a cooling zone, giving an estimated initial cooling rate from 950°C of about 50°C per sec. Average diamond pyramid hardnesses were determined on a lightly electropolished spot on the surface of each strip using 300-g load. Each point on the softening curves represents a separate annealed specimen. Sections containing the rolling direction were examined by optical metallography. Selected specimens were electrothinned to the center plane' and examined by transmission at 100 kv in a Siemens Elmiskop I electron microscope. It is well-known that changes in the structure tend to occur when a deformed strip is electrothinned below a thickness of a few hundred angstroms, although this is less serious with a material such as nickel which has a high melting point, and also is apt to be less serious when particles are present. Observations were nevertheless confined to thicker regions of the foils with estimated thicknesses over 1000A. No changes were observed due to beam exposure.

Jan 1, 1968

By D. E. Mikkola, G. E. Poquette

X-ray diffraction was used to study the growth of antiphase domains in quenched (or "disordered&apos;? Cu3Au annealed in the range 300" to 385°C. Measurements of the long-range order parameter indicate that a high degree of order is established rapidly at these annealing temperatures. Average domain sizes obtained by Fourier analysis of the superlattice peak profiles show that antiphase domain growth is analogous to classical metallurgical grain growth (i.e.,fol-lows a D2 US kt relation). The activation energy for the growth process, 44 kcal per mole, indicates diffusion control. The anisotropy in the observed effective domain sizes from seven different superlattice peaks can be best accounted for by a configuration involving antiphase domain boundaries on {100 } and (111 ) planes, where the (100) boundary is the low-energy type, {lOO} Type I. The disappearance of the (111) antiphase domain boundary during domain growth is dif-fusion-controlled with an activation energy of 48.5 kcal per mole. On the other hand, the behavior of the parameter representing the amount of (100) Type I boundary indicates that there may be a conversion of the higher-energy boundary types to (100) Type I boundary during the growth process. THE order-disorder transformation in the alloy Cu3Au has been the subject of numerous experimental investigations over the past 40 years, most of which have involved measurements of convenient physical properties such as resistivity and hardness as a function of heat treatment. The interpretation of these data is difficult because measurements of this type have the disadvantage that they yield total changes resulting from several different atomic processes which may be occurring simultaneously. The present study was undertaken to establish by means of X-ray diffraction the kinetic behavior of one of these atomic processes, namely antiphase domain growth. In the completely ordered state Cu3Au has an L12 structure which can be described as an fcc type arrangement of atoms in which the gold atoms occupy the corner sites and copper atoms the face-centered sites. Three other equivalent unit cells can be formed by allowing two gold atoms to occupy opposite face-centered sites and copper atoms to occupy the remaining corner and face-centered sites. These four different unit cells are crystallographically related by a shift of 1/2<110>. Quenching from above the critical temperature (392°C) to room temperature retains the "disordered" structure-a "random" arrangement of copper and gold atoms having the fcc structure. Annealing the disordered alloy below the critical temperature causes ordering to occur through the nucleation and growth of ordered regions at different points throughout the crystal. These small ordered regions, each based on one of the four types of unit cell, grow by consuming the disordered material until they impinge to form a domain structure in which the domains are antiphase by a shift of 4(110). The boundaries between domains are called antiphase domain boundaries (APDB) and they have been found to lie primarily on &apos; {100} planes in highly ordered Cu3Au. Two types of APDB can occur on ( 100) planes. An example of an (001)1/2[110] shear type APDB is shown in Fig. I. Because of the layer of copper atoms separating the domains in this case, there are no near-neighbor violations across the boundary and it has a low surface ener This type of APDB will be referred to as {lOO} Type I. Fig. 2 shows an (001): [011] climb type APDB, (100) Type 11. This type of APDB can be described as resulting from removal of a (200) plane followed by a shift of 1/2<110> to bring the separated regions together. Near-neighbor violations across (100) Type I1 APDB make it a high-energy boundary. There are numerous other possible APDB configurations; however, it is only worth noting that shear type APDB can be produced on the (111) plane by motion of a normal fcc dislocation with Burgers vector 1/2<110> through the ordered structure. A (111); [110] shear type APDB is shown in Fig. 3. Again, because of the near-neighbor violations this type of APDB has a higher energy than the (100) Type I APDB.

Jan 1, 1970

By G. A. Stamboltzis, N. Arbiter, C. C. Harris

Fracture under low-velocity free-fall and double impact and under slow compression have been investigated. The pattern of breakage and the size distribution of resulting fragments of sand-cement and glass spheres have been determined. Photoelasticity methods were used to simulate the stress distributions in free-fall impact in order to explain the observed patterns of breakage. Oblique fracture planes, occurring only in free-fall impact, develop along lines which coincide with the trajectories of maximum compression as determined by mathematical analysis. Breakage efficiencies for different modes of fracture were compared for both types of spheres. For the same specimen and loading system, static loading and low-velocity dynamic loading induce geometrically similar stress fields resulting in reasonably similar fracture patterns and shapes of fragments. This work had its origin in a desire to understand three fundamental processes involved in autogenous comminution: namely; free-fall impact, double impact, and slow compression. To simplify the investigation, it is preferable to reduce the entire multi-stage fracture process to its most elementary form; that is, to study products resulting from a single-stage operation, such as the breakage of a specimen under single fracture conditions. The goal of this research is to study the energy utilization in the single fracture of brittle specimens and to relate the pattern of breakage and the resultant fragment size distribution with the nature of the material, the specimen size, the manner of load application, and the rate of loading. Published works on single fracture have mainly been concerned with tests on large (> 1-in.) irregular mineral pieces, especially coal and coke. These were mainly friability tests employing a single blow on closely sized pieces. More recently, small mineral specimens in the sieve range and glass spheres have been investigated.5-7 Kick8 has reported free-fall and double impact tests with large large cast-iron, cement, and clay spheres. The establishment of a minimum breaking height independent of size in the free-fall impact tests, and the direct proportionality between the minimum work required for fracture and the volume of the specimen in double impact tests were used by Kick as an experimental proof of his classical law of "Proportional Resistances." In the present work, spherical shapes were chosen because of their simple body geometry and consequent impact and stress field symmetry. Because the study involves several physical principles in connection with brittle-fracture, it may be of interest in fields where the strength of materials is of importance. APPARATUS The equipment for the free-fall impact testing is illustrated in Figs. 1 and 2. This consisted of a massive (17 x 17 x 3-in.) hard steel plate onto which specimens were dropped and a specimen release mechanism which could be set at any desired height up to 10 ft above the plate so that the impact velocity could be varied up to about 25 ft per sec. Double impact breakage is characterized by two points of loading situated at opposite poles. For this mode of breakage the apparatus was modified (Figs. 3, 4 and 5) so that a falling mass provided an impact of predetermined magnitude on a specimen resting on the plate. A spring-loaded device operated immediately after fracture to arrest the falling mass and to record its residual kinetic energy. Precautions were taken to avoid secondary breakage. Slow compression tests were performed on a conventional hydraulic testing machine, the specimen being held between two hardened parallel bearing blocks. In the case of glass spheres, carbide bits were used. Photoelasticity studies were performed on two-dimensional models held in a loading frame equipped with a force gauge (Fig. 6). The models were viewed in a polariscope and isochromatic fringe patterns were recorded photographically. SPECIMENS Sand-Cement Spheres: A series of sand-cement spheres were prepared by molding in spherical glass flasks.

Jan 1, 1970

By Eugene S. Meieran

The effects of methods of crystal growing, wafer sawing, polishing, routine handling, diffusion, and epitaxial growth on the defects in GaAs are reviewed and studied using reflection and transmission X-ray topographic techniques. In general, it was found that boat-grown crystals exhibited fewer defects than Czochralski crystals, although all crystals showed large numbers of precipitates visible when examined in the electron microscope. Mechanical surface treatments such as sawing and mechanical polishing introduce damage to a depth of about 5 µ, most of which can be removed by suitable chemical or chem-mechanical polishing. In addition, defects can be introduced through routine handling of wafers, for example with metallic tweezers. These defects can be quite severe, and have been observed 20 µ below the wafer surface. Defects can also be introduced through diffusion and epitaxial growth. These defects, which include precipitates, growth pyramids, stacking faults, dislocations, and so forth, can be detrimental to device fabrication. It is shown that wafers or films which appear defect-free optically can contain defects visible in the X-ray topographs. WHILE the use of GaAs in the semiconductor industry has increased very rapidly in the last few years, due mainly to the recent development of many important GaAs devices,1,2 the major limit to the production of commercial quantities of many GaAs devices remains a severe lack of suitable materials technology. This lack is apparent in two critical areas. First, production quantities of high-quality GaAs crystals, reproducibly doped and precipitate-free, simply are not available commercially, although some reasonable quality material is available on a limited first-come, first-serve basis. Second, in comparison to silicon technology, little is known about the effects of processing variables on the defects either present in as-grown GaAs or introduced through processing and handling of wafers. These areas are now receiving some attention from semiconductor device manufacturers, who are studying defects in GaAs in order to better understand how either to prevent their occurrence or to cope with their existence. Most investigations of the defects in GaAs have been made by optical microscopy3-5 or transmission electron microscopy techniques.&apos;-&apos; Recently, however, the imaging techniques of X-ray topography, electron mi-croprobe analysis, and scanning electron microscopy are being applied to the study of GaAs.9-14 In the case of X-ray topography, a one-to-one image is obtained that must be photographically enlarged. In compensa- tion, the defects within entire wafers may be imaged by simple scanning (Lang technique15) if the wafer is reasonably perfect, or by using the scan oscillation technique developed by Schwuttke16 if the wafer is warped or distorted. The purpose of this paper is to both review and extend the general application of X-ray topographic techniques to GaAs. Emphasis will be placed on the effects of growth and process variables on the quality and perfection of both bulk and epitaxial GaAs. Reference to optical or electron microscopy results will be made when useful. Since the effects on defects of a wide variety of processing variables such as crystal growing, sawing, polishing, diffusion, and epitaxial growth will be somewhat superficially reviewed, a fairly extensive bibliography of the most important recent results in these areas is included. However, for completeness, important defects will be illustrated here, although such defects have been previously shown by others. While this paper is concerned with defects rather than with the physics of X-ray scattering, the mechanisms of contrast formation in the topographs will of necessity be briefly mentioned. EXPERIMENTAL GaAs crystals, both boat-grown18 and Czochralski-grown,&apos;8 containing a variety of dopants of various concentrations, were purchased from outside vendors. Wafers were sliced from the crystals using a Hamco ID saw and were mechanically polished using 1 µ diamond paste. Chem-mechanical polishing was done in bromine-methanol as described by Sullivan and Kolb.18 Chemical polishing was done using a modified sulfuric-peroxide solution, 11 parts H2SO4, 1 part 30 pct H2O2, 1 part DI water.5 Zinc diffusion was carried out in a closed tube, using a 10 pct Zn-In source at 825°C for 1 hr. Oxide masking techniques were used to select the area to be diffused. Epitaxial wafers were either purchased or prepared here. All epitaxial runs prepared here were carried out using a Ga-GaAs-AsC13 source in a closed tube at a substrate temperature of 750°C. Wafers were chem-mechanically polished and gas-etched prior to deposition. The X-ray topographs were taken on a Krystallos Lang camera, operating in the transmission scanning geometry (Lang technique15) or in the reflection scanning geometry (modified Berg-Barrett technique20,21). MoKa, radiation was used for all transmission topographs using a Jarrell-Ash 100-µ spot focus. CuKal radiation was used for all reflection topographs using a General Electric CA-7 1-mm spot focus X- ray tube. Topographs were printed from an intermediate contrast inversion film, so the contrast shown in all figures here is the same as that of the original 50-µ-thick emulsion L4 Iiford nuclear plate used to record the topograph.

Jan 1, 1969

By J. R. Vilelia

IN accordance with the custom of this society, we are gathered here, as we have every year since 1924, to honor the memory of the eminent American metallurgist and teacher, Professor Henry Marion Howe. Unlike many of the distinguished metallurgists who have preceded me as a Howe lecturer, I cannot bring to you reminiscences of his personality, for it was not my privilege to be associated with Professor Howe, or to be directly one of his students. Yet, Professor Howe and Professor Albert Sauveur, through the medium of their books, were my first teachers of metallography, as they have been of almost all American metallurgists of my generation. As a teacher, and for many years the acknowledged leader of American metallurgists, he exercised a profound influence in the growth of our science and was held in honor by the men of science of his time. I can speak no words of technical appreciation that will add luster to his fame, for by his prophetic vision, his teachings, and his researches he stands among the immortals in the memory of all metallurgists. In 1926, the third Howe Memorial Lecture was presented by Professor William Campbell&apos; of Columbia University, who entitled it "Twenty-Five Years of Metallography." He took as a starting date for his chronology the turn of the century, which coincided with his arrival from England to work in association with Howe at the Columbia School of Mines. In that informative lecture Professor Campbell enumerated the important advances in metallography achieved during the first quarter of the century, and, it now appears, may have established the custom of reviewing such progress every twenty-five years. The scope of Professor Campbell&apos;s lecture was as broad as his metallurgical knowledge, for it embraced a wide portion of the field of metallography, both ferrous and nonferrous. Twenty-five years later, the Howe Memorial Lecture Committee saw fit to assign to me the honor of writing a lecture that would commemorate the work of Henry Marion Howe and would at the same time constitute the 25th anniversary of the lecture by Professor Campbell. The Committee suggested that this lecture might properly be called "Twenty-Five More Years of Metallography," a suggestion that I have adopted. I must confess, however, that I have not followed the precedent established by Campbell and have narrowed the scope of this lecture to an appraisal of those achievements which in my opinion have contributed most to the progress of microscopical metallography during the past twenty-five years. Progress in Metallography The metallographic methods most widely used today, with the exception of the electron microscope, were firmly established more than twenty-five years ago. In general, our specimens were prepared for microscopic examination in those days in much the same manner as they are today. It is true that new details of technique have been introduced from time to time, and that superior equipment is available today, but on the whole, these improvements have been in the nature of refinements, often a matter of personal preference, and none can be considered essential to the attainment of the ultimate goal of the art and science of metallography, which is to reveal the structure of metallic specimens with unequivocal clarity so that they may be interpreted correctly. Mechanical metallographic polishing, which was the only method available in 1926, is still universally practiced and still consists of abrading the metallic specimen with a series of abrasives of increasing fineness until a specular surface is attained. We have now the alternative method of electropolishing, but it is not widely used because, except in a few special cases, its results are inferior to those of competent mechanical polishing. Likewise, most of the etching reagents preferred today were in common use more than twenty-five years ago and were applied in the same manner as they are today. Valuable improvements have been made in the optical and mechanical performance of metallurgical microscopes, but there was no dearth in those days of excellent instruments equipped with achromatic and apochromatic objectives capable of yielding micrographs comparable in quality with the best that we can make today. In fact, it would be a difficult task for any metallographer today to make optical micrographs at magnifications in excess of 3000 diameters that would surpass those made by Lucas more than twenty-five years ago. One of these is shown in Fig. 1. Yet, it is unquestionable that on the whole, the micrographs appearing in the metallurgical literature today are vastly superior to those

Jan 1, 1952

By N. A. Gokcen

The construction and operation of a simple and accurate vacuum-fusion apparatus are described in detail. Absolute accuracy of the oxygen analysis has been determined by the reduction of oxides weighed to 20.01 mg. The Bureau of Standards steel samples have been analyzed repeatedly, and their inadequacy for the acceptable range of oxygen is presented. The limits of interference of manganese, aluminum, and titanium, and the effects of tin and water-cooling of the furnace tube have been investigated in detail. ANALYSIS by the vacuum-fusion method consists of melting a sample in a degassed graphite crucible under high vacuum and extracting oxygen as carbon monoxide, and nitrogen and hydrogen as gaseous elements. The resulting gas mixture is analyzed for its constituents, from which oxygen, nitrogen, and frequently hydrogen may be determined within 1/2 hr or less. The history and summary of methods1-4 and extensive reviews of literature&apos;.&apos; for the determination of gases in metals have been published in detail. The foundation of the modern vacuum-fusion method of analysis was laid by Jordan and Eckman,11 and Oberhoffer and his associates.1, 10 Diergarten,11, 12 Meyer,13 Thanheiser et al.,14, 15 Ericson and Benedicks,16 Ziegler,17, 18 Sloman,16-23 Thompson et al.,24 and later many others contributed to the improvement, accuracy, and limitations of the method. In some investigations, however, the limitations of the procedure and the errors involved in the analysis require further critical examination and evaluation. In many apparatuses, lunnecessarily complicated and cumbersome features and elaborate precautionary measures do not have conclusive advantages. The purpose of this invest:igation was, therefore, a) to construct a very simple and accurate apparatus, b) to determine the absolute accuracy of results, c) to establish the limits of interference of manganese. aluminum, and titanium, d) to reexamine critically the reduction and recovery of oxygen from oxide powders of various sizes, and e) to evaluate critically the eight steels of the Bureau of Standards."&apos; Apparatus The apparatus used in this investigation is shown in Fig. 1. It has been used for over three years, during which several modifications were made. A brief description of the apparatus is as follows. The transparent silica or Vycor tube, E, is joined to the Pyrex head, B, by mean of a face to face ground joint sealed with mercury. A similarly sealed ball and socket joint would also have been satisfactory. A standard tapered ground joint, successfully used by some investigators, was tried, but in the absence of grease or vacuum cement it was very difficult to disassemble the joint. The graphite crucible, G, 15/16 or l 1/8 in. OD, 2 1/2 or 3 in. high, 1/10 in. wall, shown enlarged in Fig. 3a, is made from the rods containing less than 0.08 pet ash. Two baffles, overlapping sufficiently to prevent spattering, are inserted in two opposite slots cut on a band saw. Two small holes in the baffles permit the temperature measurement of the melt. A second type of crucible, Fig. 2, G, shown enlarged in Fig. 3b, is also satisfactory, though not as convenient as the crucible shown in Fig. 3a. Somewhat similar but more elaborate crucibles with baffles were first tried by Ericson and Benedicks,&apos;" but were abandoned in favor of a crucible with a stopper and a peripheral graphite powder filter. Various versions of their crucible with a stopper have later been used by other analysts, 10-27, 27-30 The crucible is packed directly in E, Figs. 1 and 2, with —35 + 48 graphite powder for shielding and insulation. A minimum layer of 7 mm of powder is necessary for keeping E cool and minimizing the blank. The first use of graphite powder was made by Sloman,10-23 Who found that —200 mesh was the most satisfactory. The author tried various size powders from +20 to —100 mesh and found that a) particles of 28 mesh or larger were not sufficiently insulating and were heated by the induction current, b) the powder finer than 60 mesh packed too much and did not readily permit the escape of gases even when the crucible was heated very slowly; hence, the powder was occasionally blown out of the side in the crucible and in the mercury pump. The optimum size powder is, therefore, 35 to 48 mesh size or 0.4 mm in average diameter. The furnace is designed to eliminate excessive amounts of

Jan 1, 1959

By C. E. Brukl, E. Rudy, St. Windisch

The ternary-alloy system Nb-Mo-C was investigated by means of X-ray, melting point, DTA, and metallo-graphic techniques; a complete phase diagram for temperatures above 1500°C was established. Above 1960°C, niobium monocarbide and the cubic (Bl) high-tenzperature phase in the Mo-C system form an uninterrupted series of solid solutions. The ternary range of the pseudocubic q MoCl-, is very restricted. Dimolyb-denum carbide dissolves up to 44 mol pct Nb2C (2240°C), whereas the maximum solid solubility of MO2C in Nb2C does not exceed 5 mol pct. The order-disorder transformation temperatures in Mo2C and Nb2C are lowered by the mutual metal exchanges. Six invariant (p = const) reactzons occur in the ternary system; three correspond to class 11-type four-phase reactions involving a liquid phase, one to a class I (eutectoid)-type, and two further isotherms are associated with limiting tie lines. The results of the Phase diagram investigation are discussed, and the thermodynamic interpretation identifies the low relative stability of the binary sub-carbides in conjunction with the large stability diflerences between niobium and molybdenum carbides as the cause for the formation of a stable equilibrium between the monocarbide and the metal phase in the ternary reson. Due to their refractoriness, the carbides of the high-melting transition metals have received increased interest in recent years as base materials in composite structures for aerospace applications at high temperatures and for the development of self-bonded cutting tool materials; other novel fields of application include power reactors, where operation at high temperatures becomes essential for attaining high power efficiencies. In these applications, the increased reaction rates at high temperatures require a close consideration of the chemical interactions between the alloy constituents. As a consequence, a detailed knowledge of the phase relationships in the alloy systems is required in order to provide a sound basis for developmental -type work. Partly as a result of the considerable experimental difficulties associated with the investigation of this high-melting alloy class, no complete studies of ternary metal-carbon systems have been performed until recently. Even the high-temperature phase relationships in the binary transition metal-carbon systems have been delineated only during the past few years to a degree of accuracy required for a more detailed study of ternary or higher-order alloys. In recent investigations of binary and ternary systems of refractory transition metals with carbon, boron, and silicon,&apos; alloys from the ternary systems Nb-Mo-C became of interest because of the demonstrated possibility2,3 of obtaining compatible composites based on metal + monocarbide combinations. In the meantime, however, studies in other, but related, ternary metal-carbon systems, such as Ta-W-C, have shown that the solid-state equilibria may change significantly toward higher temperatures (>2000°C), and that extrapolations based on low-temperature equilibrium data are, in general, not very reliable. Although the lower-temperature (<2000°C) phase relationships in the Nb-Mo-C system are similar to those found in Ta-W-C, a cursory thermodynamic analysis of the equilibria indicated4 that complete solid-solution formation between Mo2C and Nb2C should not occur at higher temperatures. The present work was conducted in order to experimentally verify these expectations and, in addition, to provide phase equilibrium data in the melting range of the alloys. In the boundary systems, niobium and molybdenum are known to form a continuous series of solid solutions.576 The continuous solubility was also confirmed by Kornilov and Polyakova,7,8 who also observed a minimum melting point at 22 at. pct Mo and 2345°C. The phase diagram investigations of the Nb-C system by Storms and Krikorian9 and Kimura and Sasaki10 were recently supplemented by Rudy et al.11,12 The system contains a high-melting monocarbide with the B1 structure, Table I, and a subcarbide, Nb2C, which exists in at least two different states of sublattice order at low temperatures47"-&apos;3 and a disordered state above approximately 2500°C.11,12 The melting-point measurements by Rudy et al .11,14 are in close confirmation of the data by Kimura and Sasaki.10 The rather complex phase relationships in the Mo-C system were only recently Clarified.15,18 The system is characterized by three congruently melting, intermediate phases, MozC, ? MoC1-x and a Mol-,, Table I, of which only Mo2C is stable at temperatures below 1650°C. Substoichiometric MozC exists in several states of sublattice order which interconvert in homogeneous phase transitions. Hyperstoichiometric compositions cannot exist in the ordered state. Upon cooling through a critical temperature range, the

Jan 1, 1968

By J. Marshall Rounsevell

It is probably not too far from the truth to say that the sulfur content of the steel bath at the first turndown of the basic oxygen furnace is influenced by every factor which varies in the operation of a BOF shop. However, the determination from normal shop operating data of the effect of a given factor on turndown sulfur content requires a means for collecting a large quantity of such data and a significant variation of the factor in question in that data. In this paper, operating data from 4000 heats collected on the computer at Inland&apos;s No. 4 BOF Shop is utilized to analyze the effect of four operating parameters -- hot metal sulfur content, hot metal manganese content, percent burnt dolomitic lime (dolomite) in the flux charge, and the presence or absence of transfer ladle slag skimming -- on first turndown sulfur content.

Jan 1, 1972

By George A. Guess

THE increasing demand for greater speed and more accuracy, in making daily assays of ores and products from mills treating material containing but very small quantities of lead and copper, has caused the older analytical methods to be supplanted by new ones devised to meet the needs of modern work. For " control " work in copper analyses, I had, previous to the present equipment, introduced in my laboratory the ordinary electrolytic method, using hollow cylindrical electrodes, and with these I began a series of experiments in determining the lead-content of daily mill-samples and controls. The results, proving accurate and satisfactory, I then devised, with Mr. H. E. T. Haultain, a cheaper electrode than the ordinary jacket electrode, which costs from $15 to $20,-the expense of the older form making the installation of many units very costly. The form of cathode finally adopted as the most satisfactory, shown in Fig. 1, is cut from 0.001-in. platinum foil. It is 12.5 cm. long, and is divided into a blade 4 cm. wide and 6.25 cm. long, and a tongue 0.7 cm. wide and 6.25 long, the immersion area being 50 sq. cm. and weight 1.5 grams. The blade is first sand-blasted and then corrugated lengthwise, in order to impart the necessary rigidity. Strips of platinum foil 0.001 in. thick, 12.5 cm. long and 0.5 cm. wide, having a median corrugation, form the anodes. Three electrodes are used in each cell, one anode in the middle and one cathode oil each side of the anode. These electrodes are connected to slotted alumi¬num terminals, in which they are held by contact pressure. The terminals are -in. rods, projecting 2 in. horizontally in front of the wall of the cabinet.; at the back the middle electrode (anode) is connected with one pole of the current, and the two outer ones (cathodes) with the other pole.

Nov 1, 1905

By J. F. Ednie

SCRAP metals to the value of more than a billion and a half dollars were recovered in the United States in 1939 for further use in industry. Few people have any true conception of the magnitude of the secondary-metal industry as related to that engaged in the production of the primary, or virgin, metals; of its importance, particularly when a shortage of primary metals exists, as at present; or of the advance that has been made in standardizing and improving the quality of its products. Of the iron and steel produced in the United States in 1939 (the data used in this article are largely taken from Bureau of Mines reports for that year) just over 50 per cent came from scrap and slightly less than 50 per cent from ore. Of the principal nonferrous metals-aluminum, anti-mony, copper, lead, nickel, tin, and zinc-63 per cent came from domestic ores and 37 per cent from scrap. Fig. 1 presents graphically the relative tonnage and value of primary and secondary production of ferrous and nonferrous metals. In this chart only purchased secondary metals are considered, the figures being exclusive of "home" or "plant" scrap which amounts to rather large figures in the iron and steel industry. Incidentally, the chart shows that from the tonnage standpoint the iron and steel industry is some twenty times larger than the nonferrous industry, though with regard to the value of the product the ratio drops to about two to one.

Jan 1, 1941

By John D. Nelson

Jan 1, 1985

By Clement K. Chase

The ammonia leach for copper recovery is discussed from historical and current practice standpoints. The chemistry of the system is presented together with Eh-pH and copper-ammonia solubility curves. A list of metals forming ammine complexes is presented. The advantages and disadvantages of the ammonia leach as applied to copper recovery in conjuction with modern liquid ion exchange techniques are compared.

Jan 1, 1980

By J. J. Reuther

Reported are singular results of a completed combustion research program designed to reliably determine the ignition, burnout, and pollution characteristics of various ranks of pulverized coal (bituminous and lignite), chars, and water-slurries of the raw bituminous coals. Well controlled simulated boiler environments were diagnosed to do so. The standardized, systematic, and comprehensive investigation established relationships between physicochemical fuel properties (coal rank, volatile matter, and reactivity) and thermochemical combustion behavior (ignition and burnout times, and NOX pollution potential) for 31 different fuels.

Jan 1, 1985

By Robert Glass Cleland

Jan 1, 1952

Jan 1, 1914

By F. J. Haller

The need for permanent, fireproof support indicated structural steel sets. Experience over the past six years, involving more than five miles of permanent underground openings, has proved that steel is permanent, safer and, in the long run, cheaper than either treated or untreated wood supports. Excavation is reduced, as are installation, transportation, and handling costs. A number of hazards are reduced or eliminated by the use of steel.

Jan 4, 1950