Search Documents

By E. I. Larsen, E. F. Swazy, F. R. Hensel

EXPERIENCE has indicated that hard bronzes are not suitable for bearing applications where high bearing loads and speeds are involved. It is the general practice to utilize softer materials for these purposes, such as copper, lead, silver, babbitt, lead-base alloys, and more recently aluminum-base alloys, preferably supported by a steel backing. It was the objective of the present investigation to study a new material produced by powder metallurgical methods susceptible to precipitation-hardening. TEST MATERIALS Preliminary tests were made with compacts containing copper, nickel and silicon in quantities sufficient to form 3 to 5 per cent nickel silicide. It was found that this type of alloy was susceptible to the formation of a soft surface shell when sintered in tank hydrogen. The depth of the shell depended on the length of sintering time and sintering temperature, and varied in thickness from a few thousandths to as much as one eighth inch. This soft shell resulted from the preferential oxidation of silicon, thereby reducing the efficiency of age-hardening by the nickel silicide compound. The body of the sintered compacts below the soft shell could be precipitation-hardened to a hardness of 70 to 85 Rockwell B, by quenching from. 900°C. and age-hardening at 450°C. A series of tests was made with various addition agents, in order to decrease the rate of preferential oxidation, and it was found that phosphorus was most beneficial in this respect. After considerable experimentation, the following nominal composition was accepted as standard: 2.4 per cent nickel; 0.8 silicon; 0.3 phosphorus; balance copper. The physical properties and certain bearing properties of this alloy are described in the present paper. PREPARATION OF COMPACTS Several methods of incorporating the hardening ingredient (nickel silicide) were studied. Compacts formed from copper, nickel and silicon powders were found to be inferior to those fabricated from prealloyed nickel silicide master alloys, because of the rapid oxidation of pure silicon during sintering. The use of a prealloyed nickel silicide hardener containing 25 per cent silicon and 75 per cent nickel could be further improved by preparing a master alloy, incorporating nickel, silicon, phosphorus and copper, having the following nominal composition: 25 per cent nickel; 7 silicon; 3 phosphorus; 64 copper. This alloy is brittle in. the cast condition and can be readily powdered. SINTERING PROCEDURE The blended powders were pressed at 25 to 40 tons per sq. in., the pressure depending on the size and shape of the compacts. Sintering was carried out in hydrogen or cracked ammonia atmospheres at

Jan 1, 1946

By Be Van Presley

There has been developed at Latouche a rather unusual system of mining which, for want of a better name, has been called the "Latouche system of mining." It is a modified form of shrinkage stoping applicable to orebodies of large or fairly large size where the ground is such that timbering would not be required in stoping. Mention has been made of this method of mining by Birchll who gave no details as it had been in use only a short time and the final outcome undetermined. The system, however, has proved to be entirely successful and it is thought that a paper covering it might be of general interest. Before proceeding with a detailed description of the Latouche system a brief description of the property and the various mining methods previously used will be given. Location The Beatson mine of the Kennecott Copper Corpn. is situated on the west coast of Latouche Island, in Prince William Sound, Southwestern Alaska, 45 miles east of Seward, the coast terminus of the U. S. Government Railroad. It is a regular port of call for ships on the Southwestern Alaska run. The island is about 12 miles long and 3 miles wide. A ridge of mountains runs the entire length with a maximum elevation of 2500 feet. Climate Latouche has to contend with possibly the greatest amount of precipitation on the North American continent. The annual average precipitation for the past 4 years has been 188 in., with 248 in. for the year 1926. A rainfall of 4 in. per day is not uncommon. In the winter the thermometer rarely falls below +20° F. and the snowfall is usually heavy during the months of March and April.

Jan 1, 1928

By William Phillips

THE possible sources of potash salts in the United States have been considered from many points of view during the last several years, but it is only within the last two or three months that the situation has become acute. We import from Germany, the only source of large supply, more than $10,000,000 worth of potash salts annually, and this business has been badly crippled by the European war. If there was ever a time in our industrial existence when the necessity of providing for our own needs was more acute than it is now, we are not aware of it. One has only to study the price, lists of chemicals sent out by the large supply houses to see the change wrought within a very short time. Whether or no these prices are to maintain for a considerable time, no one can say; but it appears to be probable that we shall not see prices materially lower for a period of uncomfortable length, to say the least. It is not my purpose at this time to discuss the various sources of supply of potash salts that have been suggested or recommended. Some of them might afford a pleasing relief but all of them combined would not affect the situation seriously. If we are to have our own sources of potash salts, they will have to compare, in some efficient manner, with the sources upon which we have drawn during the last 20 or 30 years; i.e., they must exist-in minable quantities. It seems to me to be quite idle to speculate upon our domestic sources of potash if those sources are not of a character similar to those upon which we have so long depended. A few thousand or, perhaps,, a few hundred thousand dollars' worth of chemically derived 'potash may be produced under the stress of present conditions, but when we consider that each year demands more than $10,000,000 worth, we must look to underground sources; we must look to mines similar to the famous Stassfurt and Halle deposits. If we cannot mine potash salts, we shall have to do without them for a while.

Jan 2, 1915

By Walter A. English

CONTENTS PAGE Introduction. By WALTER A. ENGLISH 1 Theory of Seismic Reflection Prospecting. By WILLARD H. TRACY 2 Instruments for Reflection Seismograph Prospecting. By ARTHUR NOMANN 9 Seismograph Field Operations. By FRANK ITTNER 15 Determining Geologic Structure from Seismograph Records. By P. C. KELLY 22 INTRODUCTION BY WALTER A. ENGLISH,* MEMBER A.I.M.E. THE four papers making up this symposum have been prepared espe-cially for those who have no knowledge of seismograph prospecting. To many people mathematics is a formidable subject, and many are discouraged from studying seismograph prospecting under the mistaken assumption that the mathematical requirements are severe. In the papers presented here there is not a single mathematical equation. We believe that considerable competence in dealing with some of the most important problems of this work can be attained without any mathe-matical training whatever. At the present time, there is a real need for interpretation of results by persons thoroughly competent to bring geologic experience and imagination to bear on data that are subject to multiple interpretation from a strictly physical viewpoint. Likewise, those charged with the responsibility of planning seismo-graph exploration campaigns would do well to become familiar with as . much as possible of the technical aspects of the work. They would then be in better position to judge of its success in individual cases. It has often been said that the seismograph is a new structure-finding tool for the geologists to use. Using a tool and using its product are two different things. One does not use an automatic screw-threading machine when he buys a box of screws at the hardware store. Neither does the geologist

Jan 1, 1939

By H. C. Lukens, E. V. Potter

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By Fred C. Bond

The Standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of cross-sectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a highspeed steel disk with diamond dust embedded in the edges, and running under a water spray. such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding lanes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing CO., and are listed alphabetically in Table I. These tests were made on one-inch cubes or on diamond-drill cores approximately one inch in diameter and One inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test NO. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TV A quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1947

By Norman Weiss

The need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of manpower in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system : if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1947

By S. A. Falconer

One of the outstanding achievements in connection with this country's war efforts has been the ability of our mining industry to supply from domestic sources many of the minerals of strategic importance that formerly were obtained principally from abroad. In order to meet the war-born demands for these scarce minerals, it has frequently been necessary to develop special methods for treating ores and waste products hitherto considered too lowgrade to be workable; and to improve the efficiency of older beneficiation processes. Important in this respect have been the recent technological advances in the field of froth flotation of nonsulphide minerals. Because of the refractory nature of many of these domestic ores, and, in many cases, the limited available technical data regarding their treatment, much research work has been necessary. The following examples describe the procedures and reagents used, and the results obtained, in certain laboratory flotation investigations conducted by American Cyanamid Company's engineers at the Cyanamid Ore Dressing Laboratory on ores containing such minerals as scheelite, manganese oxides and carbonate, ilmen-ite, brookite, kyanite, garnet, spodumene, mica, feldspar, celestite, fluorite, chromite, corundum, and cassiterite. In presenting these data, we wish to point out that many of the minerals listed have previously been tested, and their amenability to flotation reported, by other investigators—notably those of the United States Bureau of Mines. In some instances the procedures and reagents used in the treatment of some of the following described ores follow rather well-established lines, and with one or two exceptions, the reagents used were well known. However, many of the ores tested did not respond well to simple conventional procedures and it was necessary to adopt special methods of conditioning and desliming, reversal of the usual order of floatability of some of the minerals, multiple cleaning, etc., in order to secure separations. Except where otherwise noted, all numbered and trade-marked reagents mentioned in this paper are marketed by the American Cyanamid Co. or the American Cyanamid and Chemical Corporation. Tungsten ORes Tungsten minerals, vitally important in the war industries of the United States, rank high in the list of those we formerly had to import in order to supply our needs. Most of our domestic ores of tungsten contain scheelite as the valuable mineral. Today there are in the neighborhood of twelve tungsten operations in this country where flotation is used as the main or accessory form of benefication. It has, of Course, been known for some time that scheelite and other tungsten minerals respond to treatment by flotation.

Jan 1, 1947

By C. E. Wood, E. P. Barrett, T. L. Joseph

The United States Bureau of Mines has been studying the blastfurnace process for about ten years. An experimental furnace was developed by the Burcau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.' Royster, Joseph and Kinney §(48) found that the particle size of ore had an important effect upon the blast-furnace process. Kinne(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of theatock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust. Effect of Size of Material Kinney reported (p. 83(29)) the reduction of iron oxides between planes at three furnaces as given in Table 1. The Chicago furnace was operated on Lake ores. Distribution of gas was not good and much of the charge passed into the hearth before the iron oxide was reduced. The Holt furnace was operated on coarse ore. Distribution of gas was fairly uni-

Jan 1, 1930

By Arthur Phillips

The progress made in recent years in the art of dispersion-hardening has naturally led to an intensive study of alloy systems capable of yielding supersaturated solid solutions at ordinary temperatures. In general, the investigations have been confined to rather precise determinations of solubility limits and to experimental approaches designed to furnish more complete information regarding the rate and nature of precipitation under appropriate thermal conditions. Efforts are being made to focus more sharply on the atomic changes that are a direct consequence of the instability of the supersaturated solution. Here precision X-ray methods have come to be of considerable importance because lattice parameter measurements indicate very precisely the concentration of solute atoms in the solvent lattice. In spite of the general acceptance of parameter values as a criterion for the placing of solubility limits, it may be suggested that no thorough appraisal has been made of the several factors that conceivably may affect such measurements. More specifically, little attention has been devoted to the significance of surface energy conditions, specimen size and method of preparation, with particular regard to the genesis of the grains and the surface concentration changes as a consequence of heat treatment and etching. Stenzel and Weertsl recently published the results of a detailed study of precipitation reactions in aluminum-rich copper alloys. They found that, although copper lowers the lattice constant of aluminum, a 5 per cent copper alloy quenched from 150" and 225' C. had parameter values unquestionably higher than that of pure aluminum. Their results seem to substantiate, at least qualitatively, the earlier work of von Göler and Sachs,2 who indicated a parameter value, for the same alloy annealed for 24 hr. at 200° C., some 0.0008Å. larger than that of pure aluminum. Stenzel and Weerts attributed the abnormal lattice dimension to the effect of strain induced by the precipitation of CuA12. Weerts3 later

Jan 1, 1934

By Paul J. Bennett, James E. Castle

The kyanite minerals, including kyanite, silimanite, and andalusite, are anhydrous aluminum silicates with the formula Al2O3SiO2. lumortierite and topaz are also included in this group because they are closely allied in composition and thermal behavior. However, leither are mined commercially today. They ire typical metamorphic minerals which are found in metamorphic rocks on every continent. Kyanite minerals are prized chiefly for their refractoriness and are important components in a broad range of acid refractory products, especially in mortars and castables. World production of kyanite minerals is currently about 250,000 tpy and has been increasing at the rate of 3 to 8% a year for many {ears (Anon, 1972). While kyanite minerals lave widespread occurrence, the consumption of kyanite minerals is concentrated in the relatively few highly industrialized areas where refractories are manufactured, and which in turn are typically close to the major iron and steel producing regions of the world. Thus northern Europe, England, the United States, and Japan are the principal consumers of refractories and kyanite minerals. Of these countries only the U.S. is a significant producer. The largest use for domestic kyanite, both raw and calcined, is in the manufacture of refractory mortars, cements, castables, and plastic ramming mixes. In these applications kyanite constitutes from 10 to 40% of the mixture, the balance being refractory clays and coarser grog materials. A certain proportion of raw kyanite is used to offset the shrinking of the clay binder, whereas the calcined kyanite is used in the coarser sizes for body. Certain high grade refractory shapes and kiln furniture are composed chiefly of graded sizes of calcined kyanite bonded with a little ball clay. In most applications, however, kyanite is used only to fortify the mix or as a minor ingredient. Some manufacturers of mullite brick use domestic calcined kyanite for the fine-grained portion of the brick, but seldom in quantities exceeding 10% by weight. Kyanite is used by ceramic manufacturers of wall tile and sanitary ware to offset shrinkage and cracking after firing. Indian kyanite has traditionally been used to make the coarse grog sizes needed for the manufacture of mullite brick, and for the grog portions of mortar, cement, and castable mixes. It has been largely replaced, however, by synthetic mullite, high fired flint, and diaspore clay or calcined bauxite for other applications. Indian kyanite is available in lump as well as in granules and concentrates, as are sillimanite materials from India and South Africa. Andalusite is available as 8 mesh granules and as fines with chemical analyses not unlike those of domestic kyanites. From time to time and from place to place minor amounts of other aluminum silicate minerals such as dumortier- ite, topaz, and pyrophyllite have been made available at various prices and specifications, but have not been significant factors in the refractory industry. A mixture of kyanite and sillimanite of relatively fine grain-size and of low iron content was at one time offered to the molding sand industry by the Du Pont Co. as a byproduct from their deposits of heavy

Jan 1, 1975

By W. G. Whildin

This paper will be confined to a discussion of the methods in use in the property of the Lehigh Coal & Navigation Co. in the Panther Creek valley. Only the methods used in mining the Mammoth vein will be .considered, as the methods in use in the smaller veins are adaptations of the same. Typical cross-sections of the coal basin are shown in Figs. 1, 2, and 3. The Mammoth vein varies in thickness. It is 21 ft. at one colliery, 50 to 125 ft. at another, and over 200 ft. at still another. Its normal thickness is 35 to 40 ft. At some points in the Panther Creek basin the Mammoth vein is made up of three splits-the Bottom, Middle, and Top, while in other portions the dividing strata between the benches amount to only 1 ½ to 2 ½ ft., and the vein is practically in one. The section of the Mammoth vein shown in Fig. 4 was taken at the Greenwood colliery, and shows a thickness of 60 ft. The miners know it by benches, as follows:. The Three-Foot, the Four-Foot, the Eighteen-Inch Slate, the Bony, the Grey Slate, the Grain Clear, the Five-Foot, the Seven-Foot, the Slaty or Dirty benches, the Blue Slate, and the Top bench. The present-day methods of mining are an outgrowth of the experiences of the last 100 years in this territory. The first attempt at mining, according to the company's maps, was made at Summit Hill in 1792, when open cuts and pits were made. Later the pillar-and-breast method was introduced. This and other methods will be discussed hereinafter. Drifts, slopes, and shafts, according to the requirements and physical conditions, are the main openings, from which the gangways are driven. The gangways (haulageways) and airways are driven along the strike of the vein; the gangways in the various veins on the same level being connected by tunnels through the intervening rock. The gangways and airways in thick veins are heavily timbered ;throughout. The sets of timber, consisting of a collar and two legs, are spaced 5 ft. apart, and later, after the ground :has settled, additional sets, called "liners" or "relief sets," are placed between, to relieve the strain on the original timbers, so that the result is a set of timber every 2 ½ ft.

Jan 12, 1914

By J. S. Woodward, F. B. Plummer

The measurement of the rate of flow of liquids through sands dates back to 1856, when H. d Arcyb, a French physicist, carried out his classic experiments on the flow of water through sand layers. The earliest recorded data on relationships of pressure to flow of fluids through porous rocks in this country are those of Newell 23 in 1885. The first comprehensive studies of flow were made in 1898 by King15, who measured the rate of flow of water and air through consolidated and uncon-solidated sands and published the results. From 1900 to 1920 there appears to have been little interest in permeability. In 1920 the increase in demand for oil led the U. S. Bureau of Mines to begin a series of experiments to determine subsurface relationships of oil and water and the characteristics of their flow. Mills18 studied the relationship of flow of liquids to text- and structure of the sands, and Melcher17 in 1925 made a quantitative study of effect of changes in pressure on rate of flow of crude oil through Oklahoma oil sands. Since 1930 the importance of flow measurements to production of oil and gas has been emphasized by a large number of excellent investigations. Among these the works of Fettke9.10, BarbI.2, Cloud6, Nutting24-", Bot-set4, Nevin22, Tickell32.33, Fancher, Lewis and Barnes8, Moore, Schilthuis and Hurst19, and Wyckoff, Botset and Muskat"-39 have contributed much to our knowledge of the technique of permeability measurements and to the laws of liquid and gas flow through porous sands. The application of their work has led to the establishment of laboratories for measuring the permeability and porosity of oil sands by most of the large companies. All the investigations, except those of Wyckoff, Botset and Muskat, and Moore, Schilthuis and Hurst deal with linear flow; that is, flow in a more or less straight line through a given cross-sectional area of sand. Three years ago, at the University of Texas, experiments were started to measure radial flow of liquids through sands; that is, flow from all directions toward a central opening—the conditions that operate in a

Jan 1, 1937

By L. Adler

A relatively simple and effective technique is proposed to deal with the failure of geologic masses containing weakness planes. This technique, termed irextended" rupture envelope, provides a means to clearly distinguish rock and soil from fractured rock and, on a theoretical level, considers a matrix-inclusion system. It may also constitute the link between Mohr's and Griffith's failure theories. Included in the article are five sample problems concerning site location, structural design, strengthening the plane of weakness, changing the magnitudes of major and minor principal stresses and changing the orientations of major and minor principal stresses. Engineers trying to solve design problems in rock and soil mechanics have often assumed an iso-tropic and homogeneous medium. For naturally occurring geologic masses this assumption has always been viewed with regret. The following analysis which deals with the effects of plane anisotropy on failure presents a solution to this. The planes of weakness are joints, faults, bedding planes, fracture and cleavage (natural and induced), foliation and schistosity. The physical properties of these weakness planes include an undulating surface, frictional resistance, discontinuous extent, filling material, tightness and presence of water to cause a hydrostatic pore pressure. All of these properties relating to failure can be summarized in Mohr's rupture envelope for the plane of weakness. This, along with the geometrical orientation, strike and dip, of the plane of weakness produces what is termed an irextended" rupture envelope. MOHR'S STRESS CIRCLE AND RUPTURE ENVELOPE The significant features of these concepts are listed below.' 1) A point on the u - r coordinate plane represents the normal and tangential stress components on a reference area in the material. This area can have any orientation. (Fig. la)

Jan 1, 1963

By L. D. Jaffe, M. R. Norton, J. H. Hollomon

IN the practical heat-treatment of steel the decomposition of austenite usually occurs during cooling rather than at constant temperature. Nevertheless, the course of this decomposition has generally been studied only isothermally. Isothermal studies are not only simpler experimentally, but have the great theoretical advantage that one of the variables, temperature, is constant. It is the purpose of this paper to outline the principles that govern the relations between isothermal and anisothermal? decomposition of austenite, to present and systematize the available experimental information, and to indicate the gaps in the existing knowledge. Some of the experimental information is the result of new work. § Most of it is derived from scattered data in the literature. Many of these data were obtained incidentally in the course of research on other subjects and their significance has not been pointed out and perhaps not understood. It is hoped that this paper will aid future planning of more extensive research on anisothermal decomposition. METHOD In order to study the relations between isothermal and anisothermal decomposition, it appears fruitful to view anisothermal decomposition as taking place at a series of constant temperatures1 (except for the martensite reaction, which does not occur isothermally to an appreciable extent). When the time the steel is at each temperature is finite, the over-all amount of the reaction is considered to be the sum of the amounts occurring at each of the successive temperatures. During continuous cooling or heating, the time the steel is at each temperature and the difference between successive temperatures can be considered to approach zero. The over-all amount of transformation will then be given by integration over the range of temperatures involved. This point of view is advantageous in that it considers anisothermal transformation to be a series of isothermal transformations. The problem thus becomes one of determining the effect of partial decomposition at any given temperature upon subsequent decomposition at another temperature. Single Anisothermal Reaction Consider a phase brought to a temperature at which it is unstable, held there until it has partially transformed, and then brought to another temperature at

Jan 1, 1946

By R. B. Sosman, J. C. Hostetter

It is well known that ferric oxide, Fe2O3, is paramagnetic, while magnetite, Fe3o4, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe2o3 and Fe3O4 have been almost completely lacking. Fe2O3 and Fe3O4 form a solid-solution series, according to present evidence.' In this series the properties change continuously from Fe2O3 toward Fe3O4, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe3O4, but it has not yet been possible to establish the existence of such a break experimentally. The occurrence of solid solution in this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe2O3 to Fe3O4. The oxygen-pressure curves at 1100" and 1200" are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe2O3 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is impossible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe3O4 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great bulk of natural oxides of iron lie fairly near either Fe2O3 or Fe3O4 in composition. The reason will be

Jan 1, 1918

By Warnie Flint

According to statistics that have been compiled by the National Safety Council, U.S. Bureau of Mines, American Medical Association, and other agencies, accidental injuries cause more deaths than all the leading diseases. There isn't anyone who is immune to an accident. Probably the best way to describe an accident is to say that it is an unexpected happening. The automobile driver isn't expecting a terrifying crash, the electrician isn't expected to be electrocuted, nor is the coal miner expecting the roof to fall on him. All personal injuries will not result in death. There is a multitude of victims who are living proof of what accidents can mean to an individual. These are the victims who are blind, paralytic, missing arms, legs, etc. In most instances the earning power of these individuals is gone, and they are utterly dependent upon family or welfare. For many years there seemed to be an attitude that prevailed upon industrial America that accidents were inevitable, and that so many fatalities and injuries should be expected. This, of course, was utter nonsense. Since the birth of such organizations as The National Safety Council, American Society of Safety Engineers, and the U.S. Bureau of Mines, much progress has been made in reducing accidents. The enactment of compensation laws greatly contributed to the progress that has been made. Does this mean that all accidents can be prevented? Unfortunately, it doesn't. Human psychology indicates that men will work unsafely or perform unsafe acts for the following reasons: 1) Lack of knowledge or skill. 2) Conflicting motivations, such as: (a) to be more comfortable, (b) to save time or effort, (c) to be accepted by a group 3) Physical or mental condition.

Jan 1, 1973

By Hans W. Schreiber, David W. Neuhaus

INTRODUCTION The Sunshine Mining Company's 16-to-1 silver deposit and mine project are located 384 kilometers (240 miles) southeast of Reno and 360 kilometers (225 miles northwest of Las Vegas, near Silver Peak in Esmeralda County, Nevada, at an elevation of about 2,300 meters (7,000 feet). The deposit was being developed, in 1980, with an anticipated mining and milling rate of 150,000 tons per year (500 tons per day). Mining is by underground, blast-hole open stoping with rubber-tire haul-age out of the mine to a straight cyanide plant about 5.5 kilometers (3.5 miles) from the mine. The product is a gold-silver dore which may be further refined at Sunshine's new refinery in Kellogg, Idaho. The cash required for investment was obtained through the sale of $25 million worth of 6 l/2h silver-indexed bonds. Some $15.0 million were directed toward development of the 16-to-1 Mine. These bonds, which were underwritten by Drexel Burnham Lambert of Chicago in April of 1980, are redeemable on or after April 15, 1985 or payable at maturity on April 15, 1995 at the greater of either $1,000 or the market price of 50 ounces of silver. Behre Dolbear acknowledges the kindness of the Sunshine Mining Company (Sunshine) for allowing the presentation of the subject material for this Case Study. APPLICABILITY AS CASE STUDY Reasons for Choosing 16-to-1 The reasons for choosing the 16-to-1 Mine as a case study follow: 1. The project is simple and compact. 2. The mine is small -- thus relevant to other contemplated precious metal operaions in the western states. 3. The areas of risk are readily identifiable. 4. A change to project financing was under consideration. 5. A substantial decline in the price of silver was experienced during development. 6. Behre Dolbear undertook one of the first feasibility studies of The 16-to-1 and thus has some familiarity with the project. Historical Summary The following history serves as a setting: 1. Late 1920s -- minor "production"(?) via shallow pitting. 2. Mid-1930s -- neighboring Nivlok Mine successfully put into production. 3. Late 1950s (?) -- Callahan Mining Company acquired rights and drilled -- results inconclusive; Callahan turned property back to Arthur Baker, who had originally interested Callahan in 16-to-1 on the basis of its similarity with Nivlok Mine.

Jan 1, 1985

By N. A. Rose, E. L. Spain

THIS study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. INTRODUCTION When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel- exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfulls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. SOURCES AND TYPES OF MATERIALS The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1937

By H. G. Doll

An earlier paper on the general subject of the SP log has analyzed the limitations of that log, in particular when dealing with thin permeable beds enclosed in thick highly resistive ones. Under such conditions, the SP log does not give a good definition of the permeable beds. Selective SP logging is a new method which gives an accurate determination of the permeable beds; even in highly resistive formations, except when the salinity of the mud is extremely high. It also permits a close approxi. mation of the static SP to be obtained. The method consists generally in controlling the potential of auxiliary electrodes located in the drill holes in the vicinity of the measuring electrode. In this manner. the flow of SP current along the drill hole is modified to counterbalance the effect of highly resistive strata. Several procedure; and arrangements used to record selective SP curves and static SP curves are explained. Field examples illustrating these methods are given and discussed. INTRODUCTION In an earlier paper,' the shape of the SP curves and the amplitude of the SP peaks were analyzed, considering how the circulation of the SP current is influenced by the subsurface media as a function of their geometrical configuration and their resistivities. It was shown, in particular. that the permeable beds situated between highly resistive formations are sometimes indistinctly indicated by the deflections of the SP log. It is the purpose of this paper to dircuss a new method now being developed, namely selective SP logging, whose principal feature is to enable a more accurate determination of the depths of the permeable beds present in highly resistive formations, such as occur in limestone fields. It will be shown also how an addi-tional curve called the static SP log can be derived from the selective SP log, or recorded directly, to facilitate the interpretation. Another purpose of the static SP log is to provide an approach toward the determination of the value of the static SP, where this value is not readily given by the SP log. This application. although less important at the present time than that mentioned above, nevertheless is of interest, inasmuch as, according to laboratory and field experiments conducted by several investigators, the determination of oil saturation of reservoirs from the data of the electric log implies the knowledge of the resistivity of the connate water,2,3 to which the static SP seems to be related.4,5,6,7 PRINCIPLE OF SELECTIVE SP LOGGING The method of selective SP logging of the formations traversed by a bore hole consists in recording two curves under the following conditions: The measuring device comprises one measuring electrode M and two additional electrodes G-G', connected to each other. located above and below

Jan 1, 1950