Search Documents

By B. H. Caudle, L. H. Silberberg

Reservoir depletion by natural water drive is typified by the movement of water from an aquifer into the adjacent oil-bearing formation. Prior studies of this type 01 water movement have generally neglected the resistance to flow in the aquifer and its effect on the movement of water into the oil bearing zone. A method for designing and operating scaled models of such reservoir systems is presented. Experimental data on a model of an edge-water-drive reservoir are shown and discussed. INTRODUCTION Most petroleum reservoirs derive at least a part of their productive capacity from water influx. This water may be injected from the surface or it may come from an aquifer adjacent to the oil zone. In either case, the reservoir engineer must be able to estimate the advance of the water as a function of either the elapsed time or the fluid produced. This paper describes a type of fluid flow model which includes the effect of viscous and gravitational forces in the reservoir and the surrounding aquifer. Natural water influx can be divided into three general (but widely overlapping) categories according to the direction of flow in the aquifer. These are shown schematically in Fig. 1. Fig. l(a) illustrates an edge-water-drive mechanism. In this case, water advances updip along the stratum but the movement of water is essentially horizontal and very little of the oil is actually underlain by water. The bottom-water drive (Fig. l(b)) is characterized by a thick aquifer underlying the oil zone. The water movement is generally vertical in the aquifer. The third category is illustrated in l(c). Referred to as the "thin oil column", this type of oil accumulation consists of oil over water in a relatively thin stratum. Fluid movement is horizontal in both the oil and water zones, except close to the producing well. One characteristic which all three of these types have in common is that part of the water flow takes place in the water invaded region of the oil reservoir while the remainder of the water flow occurs in the aquifer. The resistance to the flow of water usually will not be the same in these two regions. This occurs because the porous rock normally contains only water in the aquifer, while the water-invaded region always contains microscopic globules of bypassed oil (residual oil) which interfere with the flow of water through the rock. The production history of any type of a water-drive system is a function of two phenomena — where the water goes, and how it displaces the oil in the area invaded by the water. It is usually impractical to study these two phenomena at the same time. In most cases one type of analysis is used to predict the gross movement of water in the reservoir, while a different type of analysis is employed to determine the amount of oil to be recovered from the gross volume contacted by the water. The portion of the oil reservoir which is invaded by water is mainly a function of the resistances to fluid flow in the several parts of the flow system. This gross water influx in the three types of natural water drive typically results in water cusping to the production wells either from the side or from below (water coning). In 1747, Muskat described a greatly simplified mathematical model for predicting the area invaded by water in a bottom-water-drive reservoir.1 This model used the Laplace equation and suitable boundary conditions to describe the isopotentials and streamlines in the flow system. The use of this model assumes that (1) the reservoir rock is homogeneous in nature, (2) the oil and water mobilities are equal, (3) there is no oil flowing in the water invaded region, and (4) external forces — such as gravity — do not affect the flow. This method has been used for both natural water drives and water injection projects. In this, as in most models, the method of images is used to reduce the size of the model necessary to describe the reservoir. The assumption of equal viscosities and permea-

Jan 1, 1966

By H. W. Hitzrot

SEPARATING a mixture of particle sizes of material suspended in a liquid medium is by no means an exact science. Selecting machines for individual classifying operations is even more difficult. The plant operator's own background is of course invaluable, and considerable help may be obtained from technical articles, talks with sales engineers, and handbooks on ore dressing. These several sources of information, however, are difficult to marshal in proper perspective for the major decision on classification units that an operator may be called upon to make. To the present writer's knowledge this assembly of facts is not available in handbooks, and technical papers are scarce on classification equipment developed in the past five or six years. It is believed that this paper will be helpful to users of classification equipment at this particular period in the development of hydro-classification. For easy reference the following classification units now available and in use in metallurgical and industrial operations are listed below, with a brief description of each. Unit-type classifiers, bowl classifiers, and bowl desiltors are all rectangular tanks, slightly tilted, with reciprocating rakes or screws to remove settled sands. The unit-type classifier, Figs. 1 and 2, is available in widths from 14 in. to 20 ft and lengths up to 40 ft. The shallow bowl of the bowl classifier, Fig. 3, equipped with rotating rakes, is superimposed on the lower end of the tank. Reciprocating rake compartments for this design range from 18 in. to 20 ft wide. Bowl diameters vary from 4 to 28 ft. The flat-bottomed bowl of the desiltor, Fig. 4, of relatively large diameter, is equipped with rakes rotating outward and partly over a pit, which is created by extension of the rectangular tank into and under the bowl section. Bowl desiltors are available with reciprocating rake sections 4 to 20 ft wide and bowls from 20 to 50 ft in diam. The bowl desiltor is used for applications beyond the range of the bowl classifier. The hydroseparator, Figs. 5 and 6, is a circular tank equipped with slowly rotating rake arms, set on a slope, with interrupted rake or spiral blades to move the settled solids to a central discharge cone. Tank diameters vary from 4 to 250 ft. Tank depths at center are 2 to 3 ft for small units and up to 25 ft for larger units. Hydraulic classifiers of the sizer and super-sorter types, Figs. 7 and 8, are narrow, deep, rectangular tanks divided by vertical baffles into a series of pockets. Hydraulic water is added near the bottom of each pocket. Perforated constriction plates, spiral flow arrangements, or jets are used to disseminate the water under pressure (hydraulic water) throughout the bed of material in the pocket. Discharge valves on each pocket are operated automatically by a pneumatic mechanism, a pincer-type mechanism, or a pressure control and motor combination actuated by a hydrostatic tube within the pocket. Hydraulic classifiers are available in 4, 5, 6, and 8-pocket units of varying constriction plate areas to suit conditions. There is now a jet sizer of unit pocket design that can be made up in 1 to 25 sections or more to accommodate sizing requirements. The hydroscillator, Fig. 9, is a rectangular tank set on a slope of 3 to 4 in. per ft. A bowl is superimposed on the lower end. The bowl bottom is an oscillating rubber-covered disk, perforated to allow hydraulic water introduced beneath the disk to set up a teeter bed and thus produce an oversize or rake product exceptionally free of slimes, and material minus the mesh of separation. A shallow dam at the periphery of the bowl allows the coarse or oversize fraction to spill over and drop down into the tank compartment, where it is moved up the deck by reciprocating rakes. The material, minus the mesh of separation, overflows a circular and stationary weir which is several inches higher than the dam on the oscillating disk. It is carried off in a circular launder in the usual manner. These units are available in bowl diameters from 4 to 14 ft and with reciprocating rake compartment widths to suit the tons per hour to be handled. Centrifugal classifiers include the solid bowl centrifuge and the cyclone classifier. The solid bowl centrifuge, Fig. 10, consists of a truncated cone fixed to a horizontal shaft and rotating at high speed. An internal spiral rotating at slightly less speed continuously removes solids deposited on the inner surface of the cone, or bowl. Feed enters the cone by means of the hollow center shaft. Overflow leaves through ports at the large end of the cone, and oversize solids, moved by the spiral, exit through ports at the small end. Centrifugal classifiers of this type are available in cone diameters from 18 to 54 in. The cyclone classifier, Fig. 11, is a stationary cone having a cylindrical upper section and a lower cone section. Feed is introduced tangentially into the upper cylindrical section under pressure from a hydrostatic head or by means of a pump. Centrifugal force thus induced effects a classification within the cone, the fine sizes being carried off in the overflow through an opening at the top of the cylindrical section. Coarse solids at relatively high pulp density exit through a control valve at the apex of the lower cone section. Cyclone classifiers are available in 3, 6, 12, 14, 24, and 30-in. diam. The cone classifier, Fig. 12, is a steel-plate cone with sides usually about 60" from horizontal. It contains no rotating mechanism. Feed enters a feed-well at center and classification is effected by gravity and pulp density. Fines are carried off in the flow over a peripheral weir at the top of the cone. Settled solids exit through an opening at the apex. An apex valve actuated through levers and rods by the pulp density in the lower cone section is usually supplied. Diameters are usually maximum at 8 ft.

Jan 1, 1955

By Harry A. Wahl

Precent fracture design procedures are bared on the total fracture area created. A method to distinguish beI,,.ecn total area and [he propped or effective fracture area has not been available. This paper presents a solution to this problem, applicable to horizontal fractures. The difierences between effective fracture area and torn] area are demonstrared in example calculations. This work is hayed on experimentally determined transport efficiencier of solids in sand-liquid slurries. Newtonian and non-Ne~vtoninn systems are considered. INTRODUCTION Fifteen years after commercial introduction, hydraulic fracturing remains the most successful stimulation technique in the oil field. This success is primarily due to ability of induced fractures to penetrate and alter permeabilities deep within formations. Many fields producing today could not have been developed without the hydraulic fracturing process. Because of wide usage, fracture-treatment design has received a great deal of engineering and research effort. This work, resulting in improved equipment and materials, has increased the benefits from fracture treatments as well as the applicability of the process. A major contribution was the development of fluid-loss additives. Necessarily, the number of parameters to be considered in treatment design has steadily increased, resulting in more complicated design techniques. Almost all present design procedures are based on the precepts set forth by Howard and Fast. Relating the fluid volume lost into the formation, the volume required in extending the fracture, and the total slurry volume injected, they developed an expression for the total fracture area created in terms of pertinent treatment parameters. Fluid loss during treatment was expressed as a function of time for three flow mechanisms. Although modifications of fluid loss equations have been made, the total fracture area concept has remained unaltered. A vast amount of field data indicate that induced fractures must be propped and held open to be effective. A notable exception is the Mesa Verde formation in the San Juan basin. However, analysis of these treatments shows that improved well productivities are obtained when propping agents are incorporated in the treating fluid. Although propped fracture area has been recognized as an important design parameter, a method to distinguish between total area and effective fracture area has not been available. The necessary information on slurry-sand transport in fractures has been lacking. Interest in the propped region of induced fractures is not restricted to areal extent alone. The distribution of sand within fractures is important from the standpoint of fracture flow capacities. Flow capacity affects the increase in well productivity after stimulation. The work of Huitt and Darin4 hows that partial monolayers of sand have large flow capacities compared to thick* dense sand packs. It has been postulated that gelled fluids have the ability to transport sand within the fractures at the deired low concentrations. An early contribution in the area of sand placement in fractures was made by Kern et al.' They studied sand movement in a transparent vertical fracture model. It was observed that the sand tended to settle out in the bottom of the model before moving very far. When the fluid velocity exceeded a certain critical value, all of the sand injected began moving through the crack even though it settled to the bottom. This critical velocity was determined under several flow conditions. Some work on sand movement in horizontal fractures has been reported in Russian publications. Sand movement was studied by Izyumova and Shan'gin' using a transparent "pie-shaped" flow model to simulate a horizontal radial flow system. However, the data were limited, especially in a quantitative sense. Dorozhkin, Zheltov and Zheltow studied the behavior of sand-liquid slurries in a horizontal linear flow model. The quantitative data were restricted primarily to the thickness of sand deposits formed at the bottom of the fracture. An earlier paper provided basic data on the flow of sand in horizontal fractures. This study was designed to yield specific quantitative information on rate of advance of sand particles and pressure behavior under various flow conditions. A comprehensive photographic study was undertaken in a 10-ft windowed flow cell to provide the necessary qualitative and quantitative data. Since the number of potential variables far exceeded the capacity of the initial study, emphasis was placed on the effects of sand concentration, oil viscosity and oil flow rate. A detailed description of these experiments and the results are described in Ref. 9. However. the implications of this work on the fracture design calculations were not discussed. An analysis of these data as well as new data is provided in the following sections. EXPERIMENTAL RESULTS The primary objective of the experimental investigation was to provide information on the rate of advance of the solids in sand-liquid sturries. A 10%-ft long transparent

Jan 1, 1966

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949

By L. E. Tanner

A study was made of the transformation kinetics of the commercial titanium-base alloys, Ti-2.5Al-16V and Ti-4A1-3Mo-1V, using two different heat treatment cycles: 1) step-quenching to aging temperatures from a ß solution anneal and 2) water-quenching from an a+ß solution anneal followed by reheating to aging temperatures. Metallographic examination and hardness testing provided the major portion of the data, while electrical resistivity, dynamic elastic modulus, and X-ray diffraction techniques were also used to obtain critical or confirnzatory data. TTT diagrams were constructed from these results. The sheet alloys, Ti-2.5Al-16V and Ti-4Al-3Mo-lV, are of current interest to the Department of Defense. As an aid to the planning of their respective heat treatments, a program was carried out to determine the transformation kinetics of these alloys using ß and a + ß reference states. This paper presents the TTT diagrams constructed from data obtained by metallographic examination and hardness testing, as well as by X-ray diffraction, electrical resistivity, and dynamic elastic modulus determinations. EXPERIMENTAL PROCEDURE Materials—Sheets of the alloys were obtained from the producers in the "mill anneal'' condition and were tested prior to shipment to assure their meeting mill specifications. Chemical analyses were also supplied and are presented in Table I. Heat Treatment—The majority of the data presented in this study were obtained from hardness testing and metallographic examination. Sample coupons were cut from the alloy sheets and heat treated on a mass scale. The annealing cycles were operated in the following manner: 1) The ß solution anneals were carried out in a horizontal tube furnace with the bare samples protected by a dynamic helium atmosphere. Following this treatment, the samples were quickly transferred to lead, solder, or oil-bath furnaces for aging. After prescribed times at the various reaction temperatures they were water-quenched. 2) The second cycle simulated commercial practice, which requires the alloys be quenched to room temperature following the a + ß sotution anneal. This anneal was carried out in a muffle furnace with a dynamic helium atmosphere. The specimens were then reheated from room temperature to the reaction temperatures in lead, solder, or oil-bath furnaces, followed by water-quenching after prescribed times at these temperatures. Information concerning the critical temperatures of the alloys was obtained from the literature and solution treatments were based on these values. A summary of the solution annealing treatments is found in Tables II and 111. The aging temperatures for the (a - ß alloys ranged in 50°C intervals from 200°C (392oF) to approximately 50°C below the ß/a + ß transus in the first cycle and approximately 50°C below the a + ß solution temperature in the second. The transformations in these alloys were known to be rather rapid, and thus aging times started at 0.5 min and went to a maximum of 7000 min. Hardness Testing and Metallographic Preparation— Heat-treated samples were sheared and mounted in Bakelite with their cut edges exposed. After a flat surface was ground, the hardness was determined in Vpn on an Armstrong-Vickers machine utilizing a 20-kg load. Three to four impressions were made on each specimen. After this procedure, the hardness impressions were removed and the edge surfaces of the specimens were prepared for metallographic examination in the usual manner. The etchant was 20 pct HF and 20 pct HNO3 in glycerine. Electrical Resistivity—It has been shown that the isothermal reactions in titanium-base alloys can be followed by measuring the changes in e1etrical resistivity attending these transformations. As mentioned earlier, the reaction kinetics of a-ß alloys are rather rapid; thus, it would be expected that resistivity data obtained from these alloys would be more significant if measurements were made continuously at the respective aging temperatures. To accomplish this end a special apparatus, based on the current-potential principle, was assembled. Its design was derived from earlier devices constructed by Colner and zmeska1 4 and Levinson.5 The set-up provided for the heat treatment zof machined specimens (approximately 2 x l0-4in. in cross section by 3 in. in length) and the determination of their relative

Jan 1, 1962

By J. F. Breedis

The morphology and crystallography of marten -site formed during quenclzing were examined by transmission electron microscopy in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pet Ni and Fe-33 wt pet Ni. Depending upon composition, four types of transformation products were observed in this portion of the Fe-Cr-Ni system. Three of these products are denoted as lath, plate, and surface martensite. The hcp structure found in association with martensite it? certain higlz-clzromium stairzless steels does not influence the transformation crystallogyaphy and cannot he Considered to act as a transitional structure in the transformation from austenite to martensite. DISTINCT changes in the characteristics of mar-tensitic transformations are produced by the partial replacement of nickel by chromium in austenitic iron alloys. Large, discrete martensite plates form in Fe-30 pct Ni, while aggregates of small crystals form in sheets parallel with (111)A austenite planes in stainless steels containing in the vicinity of 18 pct Cr and 8 pct Ni. These transformation structures are termed plate and lath martensite, respectively. In addition, an hcp structure (E) has been observed in certain high-chromium stainless steels in association with martensite. It has been suggested that the E structure acts as an intermediate step in the nucleation of martensitel-' and influences the morphology and crystallography of the final transformation product. However, this structure may be the consequence of the deformation of austenite arising from the shape distortion accompanying the transformation to bcc martensite.' An hcp stacking of atoms is produced in an fcc lattice by the introduction of an intrinsic stacking fault on alternate (111)A planes. At present, the arguments behind each explanation for the E structure are based on circumstantial evidence. This investigation seeks to determine the importance of the hcp structure to the martensitic transformation, and to examine the crystallography and morphology of the structures produced in bulk samples by quenching in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pct Ni and Fe-33 wt pct Ni. These aspects of the martensitic transformations occurring in these alloys have been studied by electron metallography and selected-area diffraction of foils examined in transmission in the electron microscope. EXPERIMENTAL METHODS The alloys have been prepared from thoroughly mixed powders of pure iron (99.6+ pct, 0.06 max pct C, 0.15 max pct N), chromium (99.9+ pct), and nickel (99.9+ pct). After sintering in an Ar-H2 atmosphere, the mixtures were melted by induction heating in recrystallized alumina boats under purified argon. The ingots were cold-rolled to 0.4-mm sheets (100 pct reduction in thickness) after the removal of at least 1.5 mm from their surfaces by grinding. Three-millimeter discs were punched from the cold-rolled sheet and annealed at 1150°C for approximately 24 hr in evacuated quartz capsules. The average grain size was 40 µ Thin foils for examination in transmission in the electron microscope were prepared from discs quenched to liquid-nitrogen temperature. A depression was first jet-machined into the center of a disc and a thin area (less than approximately 3000A in thickness) was produced at the base of the depression by electropolishing. Electron-microscope studies utilized the RCA EMU-3 and the Philips EM-100B microscopes operating at 100 kv. X-ray examination of the polycrystalline alloys was performed either in a diffractometer or in a

Jan 1, 1964

By Wilson T. Lundy

The history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur CO. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico. Terrain Characteristic of the delta region, the terrain consists of a low, flat, uninhabited area of marsh land intersected by many shallow lakes and bayous. With the exception of salt grasses, the region is devoid of vegetation and presents, in all directions, an unobstructed path to the vagaries of the winds. The general character of this area can be best visualized from the mechanism of its formation.' Offshore bars formed enclosing long narrow lagoons between the bar and the inner shore line, the lagoons communicating with the sea by means of tidal inlets. The water in the lagoons, being comparatively quiet, favored the deposition of fine debris composed of sand carried into the lagoons by action of the waves, tides and river-borne sediments from the land surface. As this material accumulated the bottoms of the lagoons were built up and eventually salt grasses obtained a foothold. The successions of growth and decay of these grasses formed a brown fibrous mat varying in depth from a few inches to several feet. This mat of vegetation virtually floats on an ooze that is several feet thick and is composed of alluvial sediments and very fine sand, and the whole is underlain by an unctuous clay. The decayed vegetation from the upper layer when dried has a peaty appearance.

Jan 1, 1934

By B. E. Terkelsen, B. J. Piearcey

A study has been made of the effect of unidirectional solidification on the creep behavior, stress-rupture properties, and thermal shock resistance of four nickel-base superalloys. The alloys Mar-MZOO, B-1900, IN 100, and TRW 1900 show improved rupture ductility and thermal shock resistance when tested with the columnar grains parallel to the major stress axis during test. The relative improvement in creep-rupture properties depends on the intrinsic strength of the alloy, a property which depends on composition, heat-treatnient, and crystallographic orientation. The data clarifies some of the factors affecting the properlies of the cast nickel-base superalloy. COMPONENTS designed for high-temperature use have, in recent years, been fabricated by precision casting techniques using nickel-base alloys developed specifically for use in the conventionally cast condition. This development was a result of both the increasing complexity of the component and the recognition that high-temperature strength was incompatible with workability. The use of castings can be economically favorable, but, more important, the recent complex designs of air-cooled gas turbine blades and vanes in alloys which possess the necessary high-temperature strength cannot be forged. Common modes of failure of high-temperature components are excessive creep, creep rupture, and thermal fatigue. If rupture occurs then the mechanism is usually by inter crystalline cracking along those grain boundaries oriented transverse to the major stress axis. In the stronger alloys, rapid propagation of intercrystalline cracks result in apparent premature failure demonstrated by the absence of third stage creep in a creep-rupture test and low rupture ductility. Tensile ductility shows a similar trend, that is, decreasing ductility with increase in strength. It is not surprising, therefore, that increases in creep strength have only been obtained with a loss in resistance to thermal shock, a property which shows a dependence on tensile ductility. VerSnyder and ~uard' showed that the application of unidirectional solidification to a brittle Ni-Cr-A1 alloy both improved the rupture life of the alloy and increased rupture ductility. Since this casting method results in columnar grains, it appeared that the solution to the lack of ductility in nickel-base alloy components was the elimination of the source of failure, namely the transverse grain boundaries. This concept was recently developed2 to produce cast-to-size gas-turbine blades and vanes consisting entirely of columnar grains oriented parallel to the major stress axis of the component. Not only did the process impart increased rupture life and ductility to the components, but it also increased their resistance to thermal shock. During this development, the effect of unidirectional solidification on the properties of several alloys was investigated. The resulting data allows certain conclusions to be drawn regarding the factors affecting the creep and stress-rupture properties of the cast nickel-base superalloy and also its resistance to thermal shock. Detailed information was obtained on the alloys Mar-MZOO, B-1900, In 100, and TRW 1900. The composition of the alloys studied are shown in Table I. MATERIAL PREPARATION AND TESTING The conventionally cast alloys are cast as +-in.-diam bars in innoculated shell molds under conditions designed to maintain control of grain size. Unidirec-tionally solidified casting were produced in the form of 3-in.-diam ingots. Specimens from the latter were machined such that the axes of the columnar grains were parallel with the axis of the test bar, except in certain cases where the transverse properties of the material were being evaluated. The specimens were tested in an axial loading creep machine.' Temperatures were measured with thermocouples, attached just outside each end of the gage length, to assure uniform temperature along the entire specimen. Chromel/alumel thermocouples were used up to 1800"F and Pt/Pt-10 pct Rh thermocouples above 1800"F. The specimen temperature was recorded and maintained within i2"F throughout the test. Creep extensions were measured automatically with extenso-meters attached to ridges on the specimen and recorded continuously using linear variable differential transformers and multipoint recording equipment. MICROSTRUCTURE The microstructures of transverse sections of the four alloys studied are shown in Figs. 1 and 2. Fig. 1 shows optical micrographs of the alloys, both in the conventionally cast and unidirectionally solidified conditions. Each alloy displays a cored dendritic structure, a distribution of MC carbide, and the presence of the y — y' eutectic constituent.~ In the case of IN 100 and B-1900, Fig. 1 indicates that in these specimens the eutectic is degenerate. That is, it consists only of y' pools indicating that the y constituent has been solutioned during the cooling period after solidification. The major effect of unidirectional solidification on the microstructures of the alloys is a tendency to promote a more dendritic form of MC carbide and an increase in dendrite arm spacing, both effects being a result of the slower solidification rate in the unidirectional solidification technique. V, lec tron micrographs of transverse sections of the four alloys in the two cast conditions are shown in

Jan 1, 1968

By H. L. Shergold, O. Mellgren

Concentration of fine quartz particles at the iso-octane/water interface has been investigated under different conditions of pH and dodecylamine concentration. The results obtained from the related studies on the effect of amine concentration and pH on the interfacial tension, adsorption density, electrokinetic potential, contact angle, and concentration of the various amine species in the system are presented. A good correlation was obtained between these different variables. It is well-known that very fine mineral particles are difficult to float in conventional flotation machines. Flotation rate studies have revealed that the rate of flotation of fine mineral particles is much smaller than that of coarser size fractions. The theories accounting for this behavior have been discussed by Arbiter and Harris1 and also Meloy.2 Theoretically, a hydrophobic fine particle might never make contact with a bubble because of the presence of an energy barrier in the vicinity of the air/water interface.' This energy barrier will have electrostatic, hydrodynamic, and Van der Waals force components. It was thought that by using an oil phase instead of air the energy barrier would be decreased so that fine particles could be concentrated at the oil/water interface more readily than at the air/water interface. The technique used involves dispersing the fine particles in water, containing the appropriate chemical reagents, and injecting a fine dispersion of iso-octane oil droplets into the pulp. After vigorous conditioning, the pulp is passed into a separating column where the oil droplets coated with a layer of mineral particles rise to the surface to form a separate layer. Air is introduced into the base of the separating column to ensure that heavy agglomerates of oil and particles report with the organic layer. This technique has been described previously4 and adopted by Lai and Fuerstenau5 who studied the alumina-dodecyl sulfonate system. The interfacial phenomena in the system composed of hematite, water, and iso-octane in the presence of sodium dodecyl sulfate have been studied and the results reported" earlier. This paper describes the results obtained from investigations into the interfacial phenomena in the quartz/water/iso-octane system in the presence of dodecylamine. The technique used in measuring the interfacial tension, electrokinetic potential, contact angle, and adsorption density were similar to those described previously? Materials Selected pieces of a high purity natural quartz, from the Isle of Man, were crushed in a laboratory jaw crusher and pulverizer. The — 52+72 mesh size fraction was retained and leached with successive washes of hot concentrated hydrochloric acid to remove iron impurities. When no iron was detected in the solution by ammonium thiocyanate, the quartz was washed thoroughly with distilled water until the conductivity of the wash water assumed that of the distilled water. Samples of 25 g of the —52+72 mesh quartz were ground for 5.25 min in an agate vibratory mill. The ground product was 100% —44 m and 57% —10 am, as determined by the Andreasen pipette. The specific surface area of the sample used for the adsorption and flotation tests was 0.94 sq m g-l. This corresponds to a mean particle diameter of 2.4 am. The —44 am quartz sample was stored under vacuum in the presence of silica gel crystals. For the contact angle determination between the three phases, quartz, iso-octane, and water, a piece of the natural quartz was ground into a block about 15 mm long, 15 mm wide, and 5 mm thick. One surface of the block was then polished by successively finer grades of silicon carbide "paper." The final polishing was conducted with alumina on a "hyprocel" paper. The polished quartz specimen was cleaned using nitric acid and ethyl alcohol followed by a wash with distilled water and then stored under distilled water. This pro-

Jan 1, 1971

By R. A. Flinn, R. D. Pehlke, D. R. Glass, P. O. Hays

Knowledge of the depth of penetralion of an oxygen jet into the bath of the oxygen converter and of the correlation of penetration with driuing pressuve, lance heighl, and nozzle throat area is vital to the understanding of converter operation. If the penetration is too shallow, then severe and hazardous slopping takes place. On the other hand, if the jel penetrates entirely Lhvough lhe bath for an apprcciublc period of time, bottom damage occurs. In addilion to measurement of the penetralion of the jel, knou~ledge of the circulatory movement in the bath is also of interest in order to evaluale various theories oj-concerter operating behavior which have been published. In this investigation, experimental converters were buill of IOU- , 300-, and 4000-lb capacity. Four independent methods were used to determine penelralion: the onset of bottom marking, a nitrogen bubbler probe, observation througlt an optical syslew built into the oxygen lance, and direcl viewing of the jet issuing from the bottom of the vessel. Good correlation zuas obtained, and empirical relalions for pvedicling perletration were found. These relations were conjzrmed by bottom marking tests in 55- and 110-ton vessels. Within the operaling conditions employed in these tests, the depth to which a single oxygen jet penetrated zuas found lo vary according to the relatiorl ThE technical literature is replete with data concerning the successful use of the basic oxygen furnace or converter in steelmaking. Experimental data are lacking, however, on the vital factors of the depth of penetration of the jet into the bath and the induced circulation. Commercial operating conditions usually have been the result of cut and try experiments in lance manipulation until satisfactory results were obtained. There have been, however, two hotly argued opposing theories concerning desirable depth of penetration and these are exemplified by the Schwarz and Miles patents1,2 on one hand and the Suess patent3 on the other. The Schwarz patent teaches that the jet, issuing from the nozzle at supersonic speed, penetrates deeply "so that the reactions between the iron and the oxygen and between the oxygen and the rest of the smelting components take place in the center of the bath". Specific operating suggestions are given by Miles.2 By contrast, the Suess patent calls for surface Circulalion was investigated by lour methods: by direct observation in 200-lb open baths, by the use of graphite rudders in the 300- and 4000-lb converlers, by direct observalion through an oplical system in the lance, and by various models al room temperature. All were in excellent agreement and indicated that the motion of the bath ulas up at the center, radially outluavd at the surface, and down at the sides. Experi-ments in small and in commercial vessels indicate that it is essential to operate with a jet penetration of approximately 50 pct of the bath depth. Surface blowing results in low oxygen eficienty and in hazardous conditions which may render the process inopeuable. RejYactory dartzage al the bottom of the vessel is only encountered when the jet penetrates to the bottom, and this can be avoided by properly applying the penetration formula. The application of this en/pirical formula in commercial peraations is best when limited to combinations of lance size, pressure, and height which are typically encounteved in the use of a single-hole lance. blowing so that "...the oxygen jet does not penetrate deeply into the molten metal bath and is confined to an impingement area at the central portion of the bath surface". These references are given merely to illustrate the basic differences between the two schools of thought and to point out the need for measurement of penetration for the sake of the operator. For example, it is shown later that inefficient and even dangerous conditions can arise if improper blowing conditions are used. Differences are also evident between the two schools of thought as to the mixing, circulation, and agitation which is to be accomplished by the jet. The Schwarz patent states that "surface contact is not sufficient in most cases to bring about quick reaction, the same as the blowing of the gas over the bath surface or the mere blowing of the gas onto the bath surface". The patent goes on to call for active mixing. In contrast the claims of the Suess patent call for "discharging a stream of oxygen ... to an extent to avoid material agitation of the bath by the oxygen stream". In this patent the circulation is said to be downward in the center and up at the sides of the vessel. A number of investigators4-12 have explored penetration and circulation in transparent models. In general, it is agreed in these tests that the circulation is upward at the center (along the sides of the jet cavity),

Jan 1, 1968

By A. L. Barnes

Residual oil in watered-out reservoirs is a tremendous reserve which has been unrecoverable by established production methods. A study of the new recovery methods indicated that the forward combustion urocess might- recover oil from such reservoirs; however, no thermal recovery operating experience in a watered-out system was available. The Delaware-Childers pilot thermal test was undertaken to test the feasibility of thermal recovery in this watered-out reservoir. The pilot test consisted of a 2.22-acre, inverted five-spot in the 600-ft deep Bartlesville sand. The reservoir in the pilot area had a porosity of 20.6 per cent, a permeability of 118 md and an average sand thickness of 45 ft. The reservoir contains a 33' API, 6-cp oil. Combustion was started Nov. 22, 1960. The initial air injection capacity was 750 Mscf/D, but it was eventually increased to 2,000 Mscf/D. The test was surrounded by an active water flood; therefore, water production was initially high, but decreased as the heat wave moved toward the producing wells. Oil-bank arrival at an individual well was indicated by a drop in GOR and WOR, and an increase in oil production. Combustion-front arrival was evident at three of the pilot producers, and they were plugged. Cumulative oil production from pilot area wells war over 12,000 bbl. Operational difficulties were negligible and only conventional equipment was necessary. The combustion efficiency of this test averaged over 80 per cent. Results from coring showed that the leading edge of the combustion front tended to be wedge-shaped but a nearly complete sweep of the reservoir was eventually obtained. An isopach map based on evidence from 10 core holes and the existing wells showed that 126 acre-ft had been swept by the heat wave. Using this swept volume, an air requirement of 15.7 MMscf/acre-ft was calculated. It was calculated that 275 ,STB/acre-ft was consumed bv the heat wave. INTRODUCTION There is a large amount of oil remaining in reservoirs that have been water flooded. A study of ways to recover this oil showed that the forward combustion process might be applicable. Results from a number of forward combustion tests have been reported in the literature, but none of these tests were conducted in a watered-out system. The Delaware-Childers pilot thermal test was initiated in 1960 to define the operating characteristics of underground combustion in this watered-out Bartlesville sand reservoir, The purpose of this paper is to present the pilot test results in detail. FORWARD COMBUSTION PROCESS The forward combustion process consists of initiating combustion in the formation surrounding an injection well and driving this heat wave through the formation toward offset producing wells. As the combustion front progresses through the reservoir, oil and formation water are vaporized, driven forward in the gaseous phase, and recon-densed in the cooler part of the formation. These distilled liquids, water of combustion and gaseous combustion products, form a bank or three-phase region ahead of the burning front. This bank pushes mobile reservoir fluids toward the production wells. The rate of movement of the combustion front is controlled by the rate at which the nondistill able residue which serves as process fuel can be completely burned off the sand. The production performance from a heat wave conducted in a watered-out oil reservoir will differ from one conducted in a dissolved gas-depleted reservoir because of the difference in fluid saturations. The primary depleted reservoir contains connate water saturation, relatively high oil saturation and some gas saturation. The watered-out reservoir contains a highly mobile water saturation, residual oil saturation and little gas saturation. As the combustion front moves forward in either type of depleted reservoir, it drives the distillable oil, the water in place and the water of combustion ahead, and burns the nondistillable portion of the oil. The heat-wave process in a watered-out reservoir differs from the process in a

Jan 1, 1966

By H. W. Meyer, H. N. Lander, F. D. Delve

A method of calculating the changes in blast-furnace performance brought about by burden and/or blast modifications is presented. Essentially the method consists of three simultaneous equutions derived from materials and heat balances. These equations can be used not only to evaluate quantitatively the effect of changes in process operating variables on furnace performance, but also to provide a useful means of evaluating changes in process variables which cannot be measured directly. It has been customary for a number of years to use simple heat and materials balances as a basis for assessing blast-furnace practice. A good example of the method used to set up these balances is that proposed by Joseph and Neustatter.1 This approach to process assessment has limited utility, however, in that it cannot be used to predict the furnace coke rate or production under new operating conditions. Using an approach based on multiple correlation of blast-furnace variables, R V. Flint2 has developed an equation which may be used to predict the change in coke rate that will result from some changes in operating conditions with a reasonable degree of accuracy. Although this equation has useful applications in production planning, it cannot be used to study the relationships between the operating variables and the fundamental thermochemi-cal characteristics of the process. In attempting to analyze the blast-furnace process quantitatively, the idea of dividing the furnace into zones3 may at first appear attractive. In our present state of knowledge, however, it is not possible to define with any accuracy the physical limits of such zones in relationship to their temperatures or to the reactions which may occur in them. Although its application is restricted, the zonal approach to blast-furnace analysis is useful in some instances. For example, the change in the calculated flame temperature in the "combustion zone" caused by injecting steam constitutes information which is helpful in understanding why the addition of steam to the blast is best accompanied by an increase in blast temperature. The zonal approach cannot, at the present time, be used to establish the relationships between process variables and process performance if the whole process rather than part of it is to be considered. One of the earliest approaches to the problem of relating blast-furnace operating variables to pro- duction and coke rate was that developed by Marshall.4 Essentially Marshall's work showed that it was possible to estimate the performance of a furnace by solving three simultaneous equations which consisted of rudimentary carbon and heat balances plus a further equation relating the production, wind rate, and the carbon burned at the tuyeres. Although these equations did not include all of the chemical and thermal variables of the process, their derivation and application seems to be the earliest attempt which achieved any success in relating prior furnace operating data to the calculation of furnace performance under different blast conditions. Work carried out in Germany has been directed mainly towards prediction of coke rates using material and thermal balances rather than statistical methods. wesemann5 used prior furnace operating data as part of the basis for predicting the change in coke rate accompanying a change in burden composition. This author employed a method of successive approximations to estimate the secondary changes in slag volume and stone rate brought about by the change in coke rate. The most recent analysis, which seems to have been developed concurrently with the thermochemical model presented in this paper, has been described by Georgen.6 This author has succeeded in improving on Wesemann's approach by expressing the total changes in the slag volume and stone rate in terms of the change in coke rate itself. This is accomplished in a manner similar to that used in the thermochemical model described in this paper. Although Georgen makes use of a calculated furnace heat loss, he does not relate the heat loss per unit of hot metal to the production rate as is done in the present work. Georgen's approach may be used to calculate the changes in materials requirements accompanying changes in furnace operation; it cannot be used to assess the resulting changes in production. The fact that blast-furnace behavior can be interpreted by consideration of the heat requirements of the process was demonstrated by Dancy, Sadler, and Lander.7 In the analysis of blast-furnace operation with oxygen and steam injection these authors showed that it was possible to account for the changes in production and coke rate

Jan 1, 1962

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for OFHC copper, and for a series of binary solid solutions of high purity copper with zinc, gallium, germanium, arsenic, and silicon, to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity. The apparatus used was of the torsional pendulum type developed by KeI1 modified so that the specimen and vibrating system could be maintained in a high vacuum. The activation energy for grain boundary relaxation in copper is 33,000 cal per mol. This is considerably less than the activation energy for self-diffusion, in disagreement with Ke's theory2 that the two activation energies should be the same. All the alloying elements increase the activation energy for grain boundary relaxation to approximately 44,000 cal per mol, increasing the grain boundary viscosity at a given temperature. The results are discussed in terms of theories of grain boundary slip put forward by MottQ and by Ke.+ Experiments have also been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. EXPERIMENTS described in this paper were designed to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity, using the internal friction method developed by Kel for measuring grain boundary viscosity. It was considered desirable to make the system under investigation as simple as possible by making experiments on a comprehensive series of binary alloys of copper with the elements immediately following it in the periodic table, i.e., zinc, gallium, germanium, and arsenic. These elements are within the range of favorable size factor for solution in copper, and the systems have been extensively investigated by Hume-Rothery and his co-workers." Later, in order to study the effect of the relative size of the solvent and solute atoms, experiments were made on a series of Cu-Si alloys, since the apparent atomic diameter of silicon when in solution in copper—the diameter necessary to assign to the solute atoms to account for the lattice constant of the solid solutiona—is almost the same as that of the solvent atoms. Preliminary experiments were made to measure the variation of internal friction with temperature for pure copper. Ke made some experiments on copper," but found that the curves obtained were not reproducible in consecutive experiments. The copper was maintained in an argon atmosphere during the experiments but, although he took precautions to exclude oxygen, Ke came to the conclusion that the precautions were not entirely satisfactory, and that the lack of reproducibility must be due to absorption of oxygen by the copper. Experiments have therefore been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. Previous Work Ke made extensive experiments on high purity aluminum and was able to show that the grain boundaries behave viscously at high temperatures. He found that the relative rate of movement of the grains could be expressed as Where v is the velocity of slip, A is the constant, u is the shear stress, H is the activation energy, R is the gas constant, and T is the absolute temperature. By assuming that the boundary layer was one atom thick, he obtained a value for the viscosity which, when extrapolated to the melting point, gave good agreement with the viscosity of the liquid metal at the melting point. Ke also made experiments on other high purity and commercial purity metals:, and on some alloys." " He came to the conclusion2 that the activation energy for grain boundary slip was the same as for self or volume diffusion and for steady state creep in single crystals. Rotherham, Smith, and Greenough" have shown recently that the activation energy for grain boundary slip is not the same as for self-diffusion in tin,

Jan 1, 1957

By H. D. Outmans

The paper presents a theoretical approach to the drilling problem based on rock mechanics and drilling fluid hydraulics at the bottom of the hole. The volume of the fractured rock around the vevtically penetrating bit tooth is expressed as a function of the tooth pressure, included tooth angle, drilling fluid pressure and formation characteristics on the assumption that fracturing is preceded by plastic flow. This assumption is verified by comparing the stress-strain state in the rock around the tooth to that in equivalent tri-axial compression tests described in the literature. An expression similar to the above is derived for the tooth penetration in the cuttings which have been retrained at the bottom. Combination of these two expressions leads to a relation between depth of tooth penetration in the virgin rock, the amount of cuttings retained and the other variables. By relating the cutting volume to the drilling rate, the hydraulic bit horsepower and the drilling fluid pressure, it is possible to arrive at formulas which express the drilling rate for viscous or turbulent flow at the cutting surface, for instant clearance, for retained cuttings, or for false tooth foundering as functions of such variables as the drilling fluid pressure, hydraulic horsepower at the bit, rotary speed and bit weight. Plotting the results as drilling curves and comparing them to published field and laboratory data justify the conclusion that the drilling model presented in this paper approximates the actual mechanism. The drilling curves serve to explain some characteristic features of the rotary drilling operation, and the equations may be used for numerical evaluation of the effect of changes in the magnitude of some of the variables on the drilling rate. INTRODUCTION Published laboratory data have established that consistent and relatively simple relations exist between the drilling rate and any one of the important variables. For instance, the drilling rate usually increases at an increasing rate with the bit weight. It increases at a decreasing rate with the rotary speed, decreases at a decreasing rate with increased drilling fluid pressure and plots as an S-shaped curve against the hydraulic horsepower at the bit. This relative simplicity seems difficult to understand considering that the drilling mechanism is a continuous process of generation and removal of innumerable individual cuttings, under different conditions for each. On the other hand, the drilling rate (although determined by this complicated process) only expresses the average rate at which cuttings are produced and cleared away. Ignorance of the drilling mechanism as far as individual cuttings are concerned, therefore, does not exclude the possibility of arriving at a concept of the drilling rate provided the mechanism is properly evaluated for the average cutting. It then may be concluded from the first sentence that this concept also should be rather simple in its final form, although not necessarily in its derivation. Two aspects of the drilling mechanism are difficult to evaluate — (1) the effect a penetrating drilling fluid has on the stresses around a bit tooth entering the formation and (2) the volume of rock fractured by a penetrating tooth which moves both vertically and horizontally. Thus, the scope of this paper has been limited to an evaluation of the drilling mechanism in formations which have a low permeability and are drilled with hard-formation bits. In the following sections, the drilling mechanism is analyzed in three steps. First, the effect of tooth pressure on the volume of fractured rock around the tooth is evaluated, assuming initially that the bottom of the hole is free of cuttings and, then, determining the effect of a layer of these cuttings. In the second section, the thickness of this layer is related to the drilling rate and the chip clearance time, and the latter to the hydraulic horsepower at the bit under conditions of laminar and viscous flow at the cutting surface. In the third section. the previous results are combined with the rotary speed into drilling equations which are then plotted and compared to experimental drilling curves. This section also contains some numerical examples of drilling rate computations. Some mathematical details are given in the appendixes. Finally, it should be mentioned that, although some drilling equations are already available, these equations (with the exception of one' which attempts to relate drilling rate to drilling fluid pressure) are all mathematical expressions for observed laboratory data; none considers the effect of delayed drill-cutting removal, an essential feature of the drilling mechanism.

By AIME AIME

ABOUT one hundred were in attendance when Donald M. Liddell opened the session* on non-ferrous metallurgy at 2 p. m. on Tuesday. F. F. Col- cord was vice-chairman. For the first part of the session the chair was turned over to Frank G. Breyer, who introduced G. L. Spencer, Jr., to read his contribution (T.P. 378), "High Silica Retorts at the Rose Lake Smelter," which was an account of the method of manufacture of high-silica zinc retorts at the Rose Lake smelter, and of the service given by these retorts. The materials used are, by volume, 50 per cent clay, 25 per cent silica flour and 25 per cent grog. Written discussion of the paper by E. M. Johnson, W. R. In- galls and M. M. Neale was read by Mr. Breyer. Mr. Johnson explained that their practice in manufacture differed very little from Rose Lake practice, but that their retorts did not last as long, possibly because Eagle-Picher does not use a hydraulic retort press or sintered ore. He ascribes the longer life of silica re- torts to the fact that they do not bend under heat. Mr. Ingalls pointed out that silica retorts are no better as heat conductors than clay retorts, but that they do have a superior rigidity in the furnace. The character of the retorts does not affect the density of the charge. Mr. Neale gave the procedure in the manufacture and use of high-silica retorts at the Donora zinc works, not

Jan 1, 1931

By Jay A. Carpenter

FIRST of several sessions at the Annual Meeting devoted to mining methods was a joint program with the Coal Division devoted to the use of Diesels underground. Fred W. Stiefel, in the first paper, stressed the saving in original cost and in operation. Wm. B. Harris then presented the paper of which he was a joint author, and S. H. Ash stressed the poisonous nature of nitrous fumes from Diesel engines even in minute quantity. Determination is difficult but in exhaust gases they are present in amount two to five times that of carbon monoxide. Jay A. Carpenter, in the closing paper of the session, stated that state laws in general prohibit the use of Diesels underground, and that almost all mine inspectors are opposed.

Jan 1, 1942

By AIME AIME

NO FEATURE of the annual meeting is considered more important at Institute headquarters than the assembly of delegates from the various local sections and divisions. There the president of the Institute and other officials may learn at first hand what the members are thinking and doing in every part of the country, and the delegates, in turn, may find that head- quarters is not a group of more or less cold-blooded New Yorkers whose primary function is to send out annual bills for $15. This year, the section and division delegates required three sessions to thresh out the matters of common interest: Monday morning and afternoon and Thursday afternoon. They were also guests of the Institute at the Directors' dinner on Tuesday night, and at the Directors' meeting afterward.

Jan 1, 1932

By George S. Rice

THE year 1929 has shown a surprising growth in the attention given by mining men to the subject of ground movement and subsidence from mining, as evidenced by the large number of articles that have appeared in technical journals, also papers and discussions in mining societies in the leading mining countries of the world. These have not been confined to consideration of the narrower limits of the subject but in application have extended to many of the fundamental questions involved in mining. The papers and discussions have been concerned with .ground movements resulting from mining of a great variety of minerals, metallic and lion-metallic. Examples of the former are: the mining of gold ore at Johannesburg, South Africa, and in the Kolar field, India; mining copper ores in Arizona and Utah; and lead and zinc in the Joplin region. Examples of ground movement resulting from mining non-metallic minerals are found in: the mining of. coal in many countries; potash mining in Germany; the mining of- common salt in several parts of the' United States; and the mining of sulfur in Texas and Louisiana; and examples of subsidence in the non-metallics are found exceptionally in the extraction of petroleum by wells, as in the Goose Creek field, on the Gulf Coast,' and recently in the Sour Lake field' of Texas

Jan 1, 1930

By M. Kashiwada

The zinc leach residues are introduced into waelz kiln to fume volatile metals and before the end of 1967, the waelz-fume containing zinc, lead, cadmium and indium was directly recycled back to the leaching process for the production of electrolytic slab zinc. However, since 1968, we have been recovering with success those valuable metals contained in the fume separately instead of direct leaching. According to the improved process, the waelz-fume, after being mixed with chloridizing agents, is fed into the rotary kiln to be roasted, wherein most of lead and cadmium content is collected as fume and most of zinc remains in the calcine. Zinc calcine thus obtained, containing 70 to 75 per cent zinc and, less than 1.0 per cent lead is sent to zinc plant for further recovery and the fume containing 40 to 50 per cent lead and 3 to 6 per cent cadmium is further processed to recover lead, cadmium and indium. The advantage of this process can be secured to the utmost when it is combined with the following subsequent treatments. (a) Blast furnace smelting of non-magnetic waelz slag to recover copper, silver and gold as matte. (b) Gallium recovering process from magnetic waelz slag. (c) Soda process of lead bearing cake produced after removing cadmium and indium from the said fume. Thus the extractions of zinc, lead and cadmium from leach residues account for 87 per cent, 72 per cent and 85 per cent respectively.

Jan 1, 1970

Since its organization, in July, 1917, the War Minerals Committee of the Institute, of which William Y. Westervelt is chairman, has been studying important phases of the mineral industry and its relation to winning the war. From this has come a realization of the imperative need for more definite coordination than is possible without direction by some governmental agency. No privately controlled industry can have the detailed knowledge of war needs or the control of all its supplies and markets necessary to effect the adjustment of its activities for war purposes. Inevitable shortages of certain essential minerals confront us unless immediate steps are taken to stimulate and develop. the mining

Jan 2, 1918