Search Documents

By J-H Shin, Y-S Jung, D-J Youn, G-J Bae

This research is to grope for a method to reduce high pore pressure taking place on tunnel shotcrete lining, especially in underwater tunnels, effectively by utilising a new concept of patternised pin drain. Accordingly, the patternised pin drain system is investigated numerically in order to confirm to the effect of reduction of pore pressure by the pin drain and its effective application. Installation of pin drain shows considerable reduction in the figure of pore pressure. It is found through 2D numerical modelling that the change of pore pressure, according to the shape and the location of pin drain, is sensitive by the sequences of the change of location > the change of length > the change of angle degree. In the results of investigation in 3D modelling, the pore pressure is the largest in the centre of the interval among pin drains, and it is possible to obtain an ideal degree of longitudinal angle and an interval by investigating pore pressure taking place on the lining.

Jan 1, 2008

By N Van Buc, E Coroiu

The rapid socio-economic growth of Hanoi City coincides with a corresponding growth of the transport demand. Today, the transport in Hanoi is completely dependent on private modes of transport. Because of the lack of an efficient public transport system and the expected rapid increase in traffic volumes, the movement of people and goods in the urban areas of Hanoi will cause congestion in the present city transport network. The solution of the construction of new roads, or the widening of the existing streets, is very expensive in urban areas and usually causes many social problems due to the resettlement of people. From the point of view of the number of inhabitants, Hanoi City is now over one million. Above this number the international experience shows that the public transportation must be a mass transport system with large capacity, commercial speed and also independent as much as possible from the street network. According to the Hanoi Master Plan for 2020, the Hanoi urban population will be over 3.5 million persons. Also, in the next 15 years, the distances between centre-destination points will be doubled by comparison to 1995.

Jan 1, 1999

The Research Centres Program initiated by the Federal Government and supported by the mining industry has had a major impact on geoscience research and education during the past five years. Eight major university based-Geoscience Research Centres are currently supported by the Government, including four Key Centres of Teaching and Research and a further four Cooperative Research Centres (CRCs). The Research Centres Program has led to a concentration of high quality research and teaching in areas of demand and strategic importance creating strong university - industry linkages and a source of well trained and motivated graduates. Over the last decade Australia's reputation as a leader in mineral exploration and ore deposit research has grown substantially, in part because of the development of the Research Centres Program, and to increased collaboration and interaction between research groups and exploration geoscientists across the industry. During a period when ore deposit research activity has been decreasing in other countries (eg USA, Canada, Japan and most European countries), equivalent research activities in Australia have been increasing, within a well co-ordinated national framework. The future challenge for universities and the mining industry will be to maintain the momentum of the successful research centres in order for the centres to become self-funding over a six- to nine-year period.

Jan 1, 1996

Synthetic and commercial activated carbons are characterised for several chemical and physical properties. A range of techniques is used to establish correlations between physicochemical parameters and gold- adsorption activities. The most important parameter in the carbon activation process for a product with a high gold-adsorption activity is the activation temperature. High activation temperatures yield products with large micropore volumes which provides sites that are ideal in size for adsorption. The surface area of an activated carbon is not necessarily a good measure of its adsorption activity. Surface oxygen-containing functional groups are identified by Fourier transform infrared spectrophotometry to be comprised mainly of ethers and hydroxyls. These functional groups line the edges of the micropores imparting a polar character to the pore and aid in the solvation of the adsorbate. Oxidants such as nitric acid result in a proliferation of surface carboxyl groups. resulting in a negatively- charged surface that is not conducive to the adsorption of gold.

Jan 1, 1993

By Mansor A. N

Results are reported for the computer simulation of heap leaching of mixed copper oxide and sulphide ores. They resemble those obtained from testwork in terms of a substantial peak in the copper concentration of the pregnant solution, an initial period when no copper emerges and a lengthy period towards the end when the copper concentration and the daily increment in copper recovery are low. The simulation can be used to forecast process results before any column or similar testwork is performed. Potential applications of the simulation to process design, operating strategy and optimisation are discussed. Three modes of operation are identified that correspond to different performance patterns and dependencies on ore and process variables. The relative merits of different operating strategies for approaching the ideal performance are being investigated. For process design and development purposes, the simulation may be used with a limited testwork programme to achieve significant savings in time and resources.

Jan 1, 1989

By D Pearce

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

By D A. Kepert, I J. Tehnas, M A. Pudovsk

BHP Billiton (BHPB) was the first company to start iron ore mining in the Pilbara at Mt Goldsworthy in 1966 through Goldsworthy Mining Limited (GML - then Consolidated Goldfields Australia, Cyprus Mines and Utah). Operations later started at Newman on Mt Whaleback in 1969 with the Mt Newman Mining Joint Venture (MNM û then comprising American Metals Climax û AMAX, Colonial Sugar Refineries û CSR and BHP). In 1986 it acquired majority ownership of MNM, and at the same time the previously 100 per cent BHPB owned but undeveloped Yandi property came on board. Purchase of Jimblebar (formerly McCameyÆs Monster) occurred in 1990 and full ownership of Goldsworthy followed in 1991. With the exception of Jimblebar (100 per cent owned), all mines are now 85 per cent BHPB and the balance with Itochu and Mitsui. This evolution of the company resulted in an eclectic mix of mines/ores, each with their varied exploration and evaluation histories. Discussion of some aspects of these histories, and reflections on changes in exploration-related activities with particular reference to discussion of advances in geological understanding since the 1960s forms the basis of this paper. BHPB presently has open cut mines at four main centres û Newman, Jimblebar, Marillana Creek (Yandi) and Yarrie û and is currently developing the former GML Area C near Yandi. With the exception of NewmanÆs Mt Whaleback mine and immediate satellites, all are contract operated. Ore is carried on BHPB railroads (696 km total) for export through the companyÆs Nelson Point or Finucane Island shipping facilities at Port Hedland. Some is directed to the BHPB Boodarie Iron hot briquetted iron plant near Finucane Island. Over 73 Mt of ore was produced by BHPB in calendar 2001, and the company has now mined over 1500 Mt in Western Australia since their operations at Yampi Sound first started in 1956.

Jan 1, 2002

Incremental sampling is defined as a solution to fight segregation, the theory is demonstrated and theoretical and practical aspects are discussed. The number of increments necessary for successful sampling is discussed. As an application, riffle splitter division is reviewed.

Mar 1, 2010

Our modern cities are almost incapable of sustaining themselves without subsurface infrastructure, which is not identifiable at first glance. This very soon becomes evident when the chaotic conditions prevailing in some cases in the multi-million cities on the African, Asian and South American continents are taken into consideration. This does not simply apply to the hopelessly congested streets in the downtown areas. If anything, it is shown here too that a subsurface infrastructure represents an important prerequisite for public health right up to banishing the danger of disease. Even during the 1990s, this has been clearly underlined through examples of cholera and plague epidemics in parts of Central and South America as well as on the Indian subcontinent. The overriding significance of an inner urban subsurface infrastructure in order to create decent conditions in the major built-up areas was once again emphasised not all that long ago at the United Nations HABITAT-II Conference in Istanbul, Turkey, in June 1996. More than 15 000 delegates from all over the world mulled over and discussed the prerequisites for humane living conditions in human settlements taking the varying climatic, topographical and cultural marginal conditions in different regions of the globe into account. Apart from the built-up areas themselves, the utilisation of underground space is experiencing high and ever increasing significance in less densely populated regions. Attractive and fast transport links between industrial centres call for high- performance transport arteries for the economic, speedy and unhampered carriage of people and goods. Important impulses for the economic power of a region or nation are provided by transport development and links. As a consequence, tunnels for roads and railways are being built or planned to a great degree for crossing mountain ranges, rivers and straits.

Jan 1, 1999

The Australasian Institute of Mining and Metallurgy (AusIMM) is a professional society for all those associated with the activities of the mineral industry. Differences of opinion exist within the membership of the AusIMM on the role it should play in the future as a professional society in a changing industry and world environment. This same dilemma is concerning other professional societies of which the author is a member. Some of the activities and priorities of the AusIMM are reviewed in order to clarify a frequently expressed opinion that it identifies with and supports industry at the expense of representing the interests of its individual members. By definition and by action this is certainly not the case and it is concluded that all activities whether seen to be industry or member orientated serve to benefit both. The AusIMM plays a most important role in integrating and promoting the interests of all sections of the mineral industry whether corporate or individual and the Presidential activities in education this year provide an excellent example of this.

Jan 1, 1997

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

By R Blin, R Walde, R Belli, D Inaudi

A fiber optic distributed sensing system allows the monitoring of parameters useful to determine the short- and long-term behaviour of the structure in response to the external actions, including, eg seismic activities as well as long-term phenomena such as seepage, tunneling, sinkholes, and other geo-structural movements. Monitoring of large retaining structures with such a system provides direct strain/deformation and temperature measurements on the broad interior area with an arrangement of several sensing cable lines, enabling early detection, localisation and sizing of subsurface damages. Measurements are provided every meter along the entire sensing cable, this is particularly important in such cases where the location of defects and damages cannot be predicted. Fiber optic distributed sensing cables are generally available for retrofit installation inside the dam structure using trenches on the downstream face or laid during construction below the geomembrane liner within the bedding sand layer. Mapping the cable route enables exact correlation between a linear coordinate on the cable length and a position in the dam. Cable installation is envisaged to be carried out during further raising of the embankment; additional cable sections are plugged to the previously installed cables and measured with the existing measurement system, requiring only an update of the mapping. The measurement system is placed remotely from the sensing area since a section of sensing cable can be used to link to the sensing area at the storage facility several kilometers away. The system is available for on-line, 24/7 real-time operational data management. Such fiber optic distributed sensing systems allow storage facilities to be monitored with long, accurate, continuous and precise data for geotechnical diagnostic purposes. This contribution will introduce the principles, benefits, and limitations of this technology.

Jul 1, 2021

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By D W. Nisbet

Today Hudson Bay Mining and SmeltingÆs 777 Project is the largest mining construction project under way in Canada. The project comprises six components: construction of the new 777 zinc-copper mine; construction of the new Chisel North zinc mine that will truck ore out from 600 metres below surface; expansion of the Flin Flon ore concentrator; expansion of the zinc plant to increase throughput by 15 per cent; a spill gas project that will reduce fugitive gas emissions by some 90 per cent; and infrastructure improvements including construction of a new electrical substation. Total investment in The 777 Project is over $US 260 million. Seven years ago, the Flin Flon, Manitoba-based company was fighting for its very existence. How does a company go from down-for-the-count to robust contender in just seven years? Contributing reasons are many, but all have their root in a process HBMS calls æTransformationÆ. It is transformation that has taken HBMS, a very traditional company, through a very non-traditional turnaround (Figure 1).

Jan 1, 2000

By R Higashi, D Maruoka, T Murakami, Y Iwami

The ironmaking industry consumes a large amount of fossil fuel derived carbon as heat source, reducing agent of iron ores and carburising agent of reduced iron. Although the demand for drastic decrease of carbon dioxide emission, carbon is an essential element for smelting process of molten iron. The carbon recycling ironmaking process by circulating CO has been already proposed to achieve carbon neutrality. However, the production of molten hot metal is not considered in this process because sufficient amount of carbon does not dissolve in reduced iron by CO. Therefore, our group has suggested a new carbon recycling ironmaking process which can produce hot metal. In this process, free carbon and iron carbides produced by carbon deposition reaction using metallic iron as a catalyst are used. It is known that only Fe3C is obtained as iron carbide by using CO gas, however, Fe5C2 is also produced by adding H2 gas. The composite agglomerated with these carbonaceous materials and fine iron ore (Deposited Carbon-Iron oxide Composite: DCIC) is reduced and melted in a furnace. It is reported that Fe3C in DCIC accelerates the reduction reaction and melting of the composite. In this study, the effects of iron carbides and free carbon on the melting behaviour of DCIC are investigated. Fe3C, Fe5C2 and free carbon were produced by vapour deposition using porous iron whiskers and CO-CO2-H2 gas. These were agglomerated with hematite reagent at a certain ratio to prepare DCIC samples with and without Fe5C2. The samples were heated up to 1300°C in inert atmosphere. The DCIC containing Fe5C2 completely melted and iron nuggets were obtained after the experiment. This behaviour was not observed in the composite without Fe5C2. This indicates that using Fe5C2 is more preferable than Fe3C for molten iron production using DCIC.

Jun 19, 2024

By P J. Hawke

Within the Mesa J pisolitic iron ore mine, clay is distributed unevenly throughout the deposit and often forms as pods and channels less than 10 m in width. The mine resource model, based on 50 m + 50 m spaced drilling, has been unable to accurately delineate the clay for scheduling and mining purposes. Therefore, alternative methods for mapping the clay-contaminated ore were sought. Predictive clay mapping will significantly reduce production costs at Mesa J through improved selective mining practices, more accurate scheduling, reduced wear on mining equipment and minimising the need for maintenance of haul roads and ramps. High lateral resolution electromagnetic (EM) surveying using a Geonics EM31 instrument can quickly and inexpensively delineate the extent and orientation of the clays. Preliminary results indicate that a block model based on the interpretation of the EM data can accurately predict the distribution, volume and tonnage of ore and waste material. While rip-line mapping, infill drilling, ground penetrating radar and gravity can delineate clay with various degrees of success, none were as efficient as EM31.

Jan 1, 2002

By J J. Frausto, G R. Ballantyne, M S. Powell, R Cruz, K Runge

Hydrocyclones are the most widely used device for classification in a grinding circuit. However, even the most efficient hydrocyclone has a bypass of fines from the feed to the underflow which reduces comminution circuit performance, as well as misclassification around the cut point. Fine screens classify only according to the particle size, allowing for a reduction in the recirculation of fines back to the mill. The development of high capacity multi-screens makes fine classification in a grinding circuit a viable option. Minera Saucito recently substituted hydrocyclones with screens in its grinding circuit. The change of classifier resulted in an increase in throughput and lead recovery but a decrease in silver recovery. This case study presents the changes in comminution and flotation performance that occurred after the installation of screens and uses historical operational data collected over 12 months of operation to investigate the reasons for these observed changes. CITATION:Frausto, J J, Ballantyne, G R, Runge, K, Powell, M S and Cruz, R, 2017., in Proceedings MetPlant 2017, pp 298–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

The Cannington silver lead zinc deposit is located near Mt Isa in North West Queensland. This world class orebody is owned by BHP World Minerals (BHP) and is estimated to contain 45 million tonnes of ore at an average grade of 11 per cent lead, four per cent zinc and 500 grams/tonne silver. At BHPÆs planned 1.5 Mtpa extraction rate, the mine life will exceed 20 years. Construction of the underground mine, which commenced in August 1993, was carried out by Peabody Resources Ltd (Mining Services Division) (PRL) for BHP Minerals Pty Limited (BHP) under contract packages totalling approximately $100 M using several innovative techniques to deliver safety, quality and time related project goals. Client/Contractor Partnering, resulting in harmonious working relationships, a combined commitment to the achievement of an excellent safety record, and a seamless transition from the construction phase to operation of the mine, has been a feature of the project.

Jan 1, 1998

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

Since the early 1990s it has been evident that electricity demand has outstripped investment in generation and transmission. At the same time, concerns were being expressed about the risks associated with the run down of the Maui gas field. It is axiomatic that the necessary investments firstly require a stable and supportive regulatory and fiscal environment, and secondly that such investments have long lead times. A unwillingness by successive Governments to fund the necessary infrastructure, however, lead to the profound restructuring of the electricity with the ultimate objective of transferring the investment risk from Government to the private sector. Successive power crises since 1992 result from a failure to put in place a regulatory framework necessary to provide the environment to allow the private sector to make the needed investments within the necessary timeframe. The electricity sector has now stabilised to the extent that the regulatory risks associated with generation investment have been reduced. This does not mean that risk has been eliminated, however, and both economic and environmental issues will continue to constrain investment in some power proposals particularly those in the South Island and especially any South Island coal or gas thermal proposal. This is firstly because of several very simple economic issues:  1. while the South Island may have significant coal resources it lacks a significant electricity market; 2. except for a six to ten week period in a dry year, low cost hydro will price any large-scale South Island thermal out of the market which will restrict any large scale thermal station to a dry year and/or peaking load; 3. except for a six to ten week period in a dry year, export capacity on the HVDC link to the North Island is constrained to around 964 MWe (and 482 MWe from North to South in dry years); and 4. construction of any new thermal plant in the northern half of the North Island will price any South Island thermal station out of the market. There are also significant environmental issues associated with the establishment of a large scale thermally based power station in the South Island. Because the South Island lacks any large scale economically proven gas reserves, the environmental constraints considered are those associated with coal production. A coal mine dedicated to power generation will have significant on-site impacts associated, in particular those associated with disposal of opencast overburden and visual impacts. These will, however, be partially offset by the relative remoteness of such sites to population centres. What cannot be offset, however, is the off-site impacts, in particular, CO2, SOx and NOx emissions, water disposal and acid mine drainage.

Jan 1, 2003