Search Documents

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By T Arena

To maintain copper recoveries and maximise production at the Sepon Copper Operation it is crucial to control the amount of copper entering the leaching circuit. This requires close control of blending of the multiple ROM stockpiles to achieve the desired head grade. Grade variability in the ROM stockpiles can lead to significant variation in the processing plant copper feed grade.Head grade sampling from the milling circuit at Sepon is complicated due to milling in leach solution to preserve the water balance. Copper is present in both liquid and solid forms and copper in the added milling solution has to be accounted for. This leads to difficulties in manual head sampling which also introduces delays due to sample preparation and assay turnaround. On-stream analysis is complex because of the solution and solid copper and the need to account for recycled copper solution.This paper describes the complexity of feed grade management at Sepon and the application of on-belt analyser technology to assist in the control of copper metal throughput.

Aug 8, 2011

By P McCarthy

The relatively new field of geo-metallurgy promises to improve the predictability of mill feed quality and enhance processing outcomes. However, it is subject to the same limitations as the prediction of grade using geostatistics and has additional limitations due to the spatial distribution of the variations being measured and the sample sizes required. Schedules based on geo-metallurgical models will, in turn, be subject to variations arising from geological control and practical mining constraints.This paper discusses the key drivers of variations in mill feed quality and quantity from a mining perspective. It concludes that geo-metallurgical modelling addresses only one aspect of the problem. A case study is provided to illustrate poor predictability of metallurgical performance even with very detailed geological data.

Aug 8, 2011

By M Thompson, N Vines, Z Hearne, S Lam, G A. Gomes-Sebastiaõ, D van der Spuy

Construction and commissioning of the Nova Copper-Nickel project of Independence Group was completed in late 2016. The plant is in the Fraser Range of Western Australia, about 120km east of Norseman and produces separate Copper and Nickel concentrates. Since the early feasibility phases of the project, the importance of automation and control was recognised and planned for to ensure the plant performance meets the design expectations. The site is well equipped with common as well as advanced instrumentation. It currently boasts the largest number of Blue Cube MQi (mineral quantifier inline) slurry grade analysers on a single plant worldwide. It was also decided that 25 Blue Cube TempoTracks would be installed on the flotation cells. The TempoTracks provide information on froth height and velocity, hence giving continuous, quantitative measurements of the froth that is pulled off each cell, rather than relying on infrequent, subjective visual inspections.The Nova concentrator consists of a differential flotation circuit whereby copper bearing mineral are selectively floated prior to nickel flotation. It is imperative that losses of copper to the nickel circuit, and vice versa, are minimised. The plant metallurgical team and Process IQ collaborated to develop and implement the advanced control strategy for the plant. This paper focusses on the optimisation of the copper concentrate that is pulled off the copper rougher and scavengers. This strategy was made possible by the additional measurements listed above. The control optimisation of the copper rougher and copper rougher scavenger circuit was implemented during August 2017 on the StarCSTM advanced control platform. It continuously optimises the level and air setpoints. The control philosophy incorporates several notable techniques which include: a variable mass pull target that is a function of the quantity and grade of material entering the circuit, integrated compensation to prevent inventory build-up in cells, balancing of the froth velocity over the lip of each cell to adaptive, modular system usage and advanced error handling. CITATION:Gomes-Sebastiaõ, G A, Hearne, Z, Lam, S, van der Spuy, D, Thompson, M and Vines, N, 2018. Nova copper-nickel project optimisation of the copper rougher-scavenger circuit through advanced measurement and control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 77–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By T Elkington, A Finch

The theory of constraints (TOC) is a business improvement method that focuses on exploiting a business’s bottleneck to deliver the highest possible profit. Early applications were mostly in the manufacturing industry; however, the theory in itself is completely generic and has now been applied widely in other industries such as services, retail, software and distribution, amongst others. The intent of the approach is attractive – it focuses on the ‘silver bullet’ rather than ‘death by a hundred projects’, and it focuses on growth rather than cost cutting. Application within the mining industry has been limited to date, although there are a few applications emerging. This paper discusses how TOC can be applied to maximise value during the project planning phase and how to maximise profits when the mine is operational. The paper uses two case studies to illustrate the approach. Case study 1 uses the approach to improve tactical mine planning, which delivers an increase in revenue of 58 per cent. The second case study is a strategic mine planning example that delivers an increase in value of 77 per cent.CITATION:Finch, A and Elkington, T, 2014. Application of the theory of constraints to strategic and tactical mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By L Rachmad

Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) deposit which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. Evaluations were made on former block caving mines at PT Freeport Indonesia (IOZ, GBT Area I and II) in order to design a more appropriate support system. As a permanent support, the thread bar bolt support system is widely used in the DOZ mine. The advantages of this system are ease of operation, quality control and high bond strength. The main problem of this system is the curing time of about 28 days to achieve maximum strength, necessitating the installation of a temporary support for its implementation. In this instance, the system was inefficient in operation and studies were required to find an alternative grouting system. This paper examines the evaluation of thread bar bolt support system and compares the performance of two types of grouting (resin cartridge and cement cartridge) with cement grouting performance. The evaluation is conducted with a pull out test. The advantages and disadvantages for each grouting method, comparison of cost estimation and grouting application in mine scale are presented in this paper.

Jan 1, 2002

By B Mack

The cost of water treatment is now more than ever a major consideration for maintaining an environmentally and economically sustainable mining operation. As an industry, we often have to consider water sources that are highly impure and difficult to treat. We are also discovering the value of our waste waters in this regard and using new and improved methods and technology to reclaim and reuse water. In many instances, the water or waste water to be treated is highly acidic and saturated in sparingly soluble salts. Conventional systems used to liberate this type of water typically involve high doses of lime with large volumes of waste sludge produced, and are comparatively complex to operate, to pretreat the water in order to reduce scaling tendency on the reverse osmosis stage. However, if the water is considered valuable for reuse, then why not avoid difficult and cumbersome pretreatment processes and treat the water at low pH to keep the sparingly soluble salts, metals and other dissolved species in solution. This paper describes a patented technology that uses and successfully proves this concept as a cost effective option for certain situations. Results from a treatability study on an Australian groundwater are discussed, along with an economic comparison to a conventional method and discussion on full-scale potential.

Jan 1, 2009

Cannington Mine is an underground, hard rock, metalliferous mine located in North-Western Queensland, Australia. Weld mesh is installed to prevent the failure of rock from between the installed reinforcement elements. Corrosion reduces the capacity and life expectancy of mesh and presents a real hazard to underground personnel and equipment as it reduces the effectiveness of the support system. Corrosion influences the economics of the mining operation through the need to conduct rehabilitation of the ground support which involves re-installing new mesh or shotcreting over the affected mesh to protect it from further corrosion. The requirement for rehabilitation is determined by the geotechnical engineer based on an individual visual assessment with little or no engineering input. It was identified that a more quantitative method was required that considered the safety and economic risks involved. A project was undertaken to develop a simple method to evaluate corroded mesh and to provide selection criteria for rehabilitation. A weld mesh corrosion classification has been developed that relates the average wire diameter of corroded mesh to the remaining capacity of the mesh. Accompanying selection criteria provides recommendations as to when rehabilitation may be required based on the estimated residual mesh capacity, the remaining development life, and the level of personnel exposure.

Nov 25, 2010

By S Tierney, D Cumming-Potvin, I Thin, Y Potvin, D Grant

The preliminary modifying factors for future stope design in the Southern Mine Area of Olympic Dam consisted of only a single, arbitrary value of Equivalent Linear Overbreak/Sloughing (ELOS). In order to improve this, a study was conducted which developed a more comprehensive methodology for assigning ELOS, Equivalent Linear Lost Ore (ELLO) and Equivalent Linear Fill Overbreak (ELFO) to individual stope faces based on geotechnical and mining parameters. The approach used was to look at the simple cases, which were classed as vertical stope walls in good ground (RQD 80-100%), divided into wall orientations (North, South, East, West). The stope walls were also split based on the blasting practice used (toeing, parallel or a combination of the two). The expected ELOS and ELLO from these ‘base cases’ are then modified by parameters which have historically been found to affect stope performance (Hydraulic Radius and Q’). The size of the effect found in the historical data determines the ELOS / ELLO applied. The methodology was summarised in an easy to use flow chart and was applied to all of the proposed stope shapes for the Southern Mine Area and summarised per mining block. This allowed each iteration of the mine plan to be assessed in terms of overbreak (both rock and vertical fill exposures) and underbreak.

Mar 15, 2021

By D Luppnow, H Rourke

Recent disasters such as the failure of the Mount Polley tailings embankment remind us of the risks that tailings facilities pose. It is widely recognised that dam-break assessments are a vital tool in identifying the consequences of the failure of a facility, which in turn can be used to develop emergency action plans. A typical assessment includes an estimation of breach parameters and outflow volume, followed by the preparation of an inundation map to illustrate potential flow extents and downstream impacts. This paper focuses on the estimation of outflow volumes, which is an area that the authors feel can be improved. Presently, many types of analyses assume that the volume of tailings released is only a function of the storage volume and dam height. After a review of several documented tailings failures, it has been found that the extent and depth of the supernatant pond needs to be considered as it is just as important, if not more so, as the storage volume and dam height. Tailings facilities with excess water storage have a higher risk of failure as they are more susceptible to overtopping, piping and liquefaction failures. In addition, they pose greater failure consequences as the saturated conditions will lead to more material being mobilised.This paper has reviewed available information on a number of tailings dam failures and proposes an alternative estimation of potential tailings release volumes as a function of supernatant water stored on the facility for use in dam-break analyses. In a broader sense, the paper seeks to shift the current risk paradigm from tailings dam heights to volumes of water stored and provides a basis for continuing research and discussion.CITATION:Rourke, H and Luppnow, D, 2015. The risks of excess water on tailings facilities and its application to dam-break studies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By B Jones, M Chappell

Permanent rock bolts used to support rock tunnels are required to perform for the design life of the structure as a minimum. Quality of installation is critical to the performance over the life of the rock bolt.This paper will present the findings from an in investigation into the integrity of rock bolts installed in an underground hydroelectric power station cavern and access tunnel. The 25?mm diameter rock bolts were installed 50 years ago, tensioned and post cement grouted. Due to a major machine upgrade the whole facility was subject to an asset survey. The owners are responsible for managing the risks associated with the failure of these rock bolts and ensuring the structural integrity of the tunnels and caverns is maintained to continue operations, protect machinery, assure production and more importantly maintain a safe working environment for all employees and visitors.To help manage risk a proactive approach is desired. To this end a test schedule using a non-destructive testing (NDT) system was carried out by Independent Integrity Testing Pty Ltd (i2t). The system used in this application was RokTel™. The system operates by applying a small axial impact to the rock bolt end and measuring the resultant acceleration response. The rock bolt characteristics affect the acceleration response.The data output from the system is analysed principally using Fourier Analysis (FFT) and sinusoidal waves. The energy generated in the bar, the rate of damping and changes in frequency are all assessed. Testing was carried out on 70 rock bolts within the tunnel and cavern. A selection were then over cored, photographed and documented. The data gathered from the testing is then correlated with physical evidence to establish a calibration for the remainder of the rock bolts and assess if this is a viable method for identifying defective elements, and what degree of accuracy can be achieved. The findings will assist with the future assessment of similar hard rock underground?facilities.CITATION:Jones, B and Chappell, M, 2014. The use of non-destructive testing to identify defective rock bolts – a case study, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Millar, B Wraith

Process plants are characterised by variability of performance over a wide range of time-scales; reflected in fluctuations in metal recovery, concentrate grade, plant throughput and reagent costs. In turn, these fluctuations impact financial metrics such as operating costs and revenue. The primary cause of plant variability is variation in the physical, lithological and mineralogical characteristics of the ore fed to the plant. The variability of the ore is driven by the intrinsic heterogeneity of the geology and mineralogy of the orebody, the mining method and mine production plan, the capacity to stockpile and blend, as well as the plant flow sheet and the level of plant automation. Whilst the impact of ore variability on process plants is universally recognised, it is rarely quantified in financial terms. Consequently, opportunities to reduce its impact are often overlooked due to the lack of a basis for a quantifiable cost-benefit analysis to justify improvement initiatives. This paper will present case studies using production data from the Renison tin concentrator and a zinc concentrator. These case studies demonstrate that as the standard deviation of plant head grade increases (as a proxy for ore variability), plant metal recovery subsequently reduces. The metal recovery is then converted into plant revenue losses, to quantify the economic impact of ore variability. The Renison case study demonstrated that whilst a very rare occurrence, revenue losses were as high as 34 per cent (relative to the baseline) when standard deviation was at its highest. The zinc concentrator case study demonstrated that revenue losses were as high as 6 per cent (relative to the baseline) when standard deviation was at its highest. Options are available for reducing and managing ore variability in the process plant. These options include changing mining practices so that the ore is fed to the plant with less variability, more advanced process plant control systems and the use of predictive geometallurgical models.

Aug 24, 2022

By S Ellis

In January 2008 Chirano Gold Mines Limited committed to expansion of the Chirano Gold Project from its existing design capacity of 2 Mtpa ROM ore to a new design value of 3.5 Mtpa. In addition to increased throughput, the design had to contend with increasing ore hardness and competency, while at the same time make cost effective use of existing equipment with minimum disruption to existing production. The solution adopted involved some novel approaches including tertiary crushing and operation of the SABC circuit in overflow ball mill mode and parallel elution with a common acid wash column. This paper describes the approach taken to the design of these elements to achieve a cost effective and safe capacity expansion.

Aug 8, 2011

By Taylor G. R

Fluid inclusions within quartz accompanying several stages of mineralization at Hillgrove are de cri bed. Pyrite-arsenopyrite-gold mineralization shows uncorrected filling temperatures of between 195°C and 250°C. Later stibnite-antimonide-siderite and stibnite-calcite mineralization has filling temperatures between 100°C and 195°C and a bimodal distribution of temperature peaking at 175°C and 145°C, possibly correlated with the two stages of mineral deposition. Secondary included fluids within an earlier generation of deformed quartz veins are derived from hydrothermal fluids contemporary with the main-stage mineralizing fluids described above. Primary inclusions within latestage, cross-cutting quartz-chlorite-calcite veins show these veins to be unrelated to the mineralization.A correlation between filling temperatures and salinities indicates that mineralization accompanied the mixing of a hot, partly saline, fluid (at 5 per cent equivalent NaCI) with cooler, less-saline meteoric or connate water. Over a vertical distance of 200 m, equivalent mineral assemblages were deposited over the same temperature range. Studies on single crystals suggest rapid deposition with fluid temperature dropping 45°C during their growth. Ore mineragraphy and the fluid inclusion data suggest that the metals were transported by sulphur-poor, relatively low-temperature, low-salinity solutions, possibly as carbonate complexe , and that a vertical zonation of the W-Sb-Au mineralization is compatible with the mixing of this hydrothermal fluid with cooler groundwater. Regional metallogenic and geological considerations suggest that ore metals are derived from the remobilization of deep-seated stratabound deposits or from metamorphic fluids expelled from deepseated volcanoclastic sediments.

Jan 1, 1984

By Nilmani M, Fountain CR

Injection of gases into slag-melt mixtures produces various zones as a result of bubble formation and disintegration within the melt. The extent of these zones depends on the type of reactor used. When compared with ferrous processes, non ferrous processes are character- ised by large bubbles formed adjacent to the tuyeres, low flowrates and shallow tuyere sub- mergence. These features can result in a greater proportion of reaction occurring above the bath, more refractory wear and tuyere blockage with more splashing. The large bubble zone adjacent to the tuyeres has been investigated using the tech- niques of physical modelling, mathematical modelling and plant trials. Large bubble form- ation in physical models was recorded using a high speed camera and a rapid response pressure transducer coupled to an oscilloscope and data recorder. It was found that the bubble volume (Vb) could be correlated at low flowrates using the single bubble model Vb = 1.378 Q6/5 g-3/5 Deviations from this correlation occurred with increasing gas jet momentum. Plant trials were carried out on a copper converter at Mount Isa Mines during five different charges. Pressure measurements were made through the tuyeres during the slag blow and commencement of the copper blow. The power spectrum density showed that the dominant pulse amplitude occurred at a frequency of approximately 3 pulses/sec. Plant data from this and other converters were correlated using the same relationship as for physical modelling. De- viations occurred due to the state of the re- fractory, bath composition or bath circulation effects.

Jan 1, 1984

Large deposits present computational challenges to todayÆs commercial orebody modelling systems that are based on conventional block models. We describe a system that is specifically engineered to model and visualise large deposits. Central to the system is linear octree encoding of conventional block models and real-time conversion of three-dimensional (3D) meshes to linear octrees. We provide both methodological treatment and practical experience in implementing such a system. A commercial implementation is also presented to demonstrate the validity of the approach.

Sep 26, 2011

By K W. Bian, Y M. Liu

Tongkuangyu Copper Mine is currently the only mine in China employing block caving. It comprises two large orebodies known as the No 4 orebody and the No 5 orebody. They are approximately 50° in dip angle, 80 to 240 m in width and 800–1000 m in strike length. The two orebodies are separated by a distance of 110–130 m. Production with block caving originally, ie Phase 1 project started at Tongkuangyu from the first undercut at a depth of 200–300 m below the ground surface and designated as Lift 810 m in late 1989 and has continued to the present. During the last 25 years Tongkuangyu has mined three lifts: Lifts 810 m, 690 m and 530 m. The previous two lifts utilised a slusher process with an annual designed production rate of 4 Mt. In this context the lift name represents the elevation of track haul level.The Tongkuangyu Phase 2 project serves for two lifts (ie Lift 530 m and 410 m) under the elevation of 690 m and the annual designed production rate is 6 Mt. Since the orebody is approximately 50° in dip angle, it is originally designed that production at Lift 530 m is comprised of one main extraction level and two auxiliary extraction levels in the footwall and undercutting is started from one end of the extraction footprint forward to another end, which is from north-east to south-west.Production at Lift 530 m started from March 2011 and reached to 6.39 Mt in 2013 and 6.9 Mt in 2014. Additionally, Tongkuangyu improved block caving processes and used modern mining equipment, which differ from the previous two lifts. Blastholes for undercutting and drawbell-preparation are now drilled using jumbos. The blasted ore is transferred to the underground crushing station via 10 t electric load-haul-dumps (LHDs) and then delivered to surface via a belt conveyor 3200 m long.Due to increasing ground pressure, a consequence of mining depth increase, stress abutment and inadequate support, significant damage occurred at the Tongkuangyu Copper Mine with production at Lift 530 m. This resulted in significant production delays and rehabilitation costs. A series of improvements have since been implemented including an advanced undercut sequence and increased ground support. All of these improvements have allowed Tongkuangyu to alleviate ground control issues, reduce operating costs and ensure safe production.CITATION:Liu, Y M and Bian, K W, 2016. Production at Lift 530 m of Tongkuangyu Copper Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A M. Ebbels, D Pratt

The current commodities super-cycle has seen an explosion in the number of mining projects demanding human resources throughout the world. The demand for key personnel currently far outweighs the international talent pool and will take several years to subside. A highly effective project team can be the difference between a successful project and a bad public relations exercise. Building an effective team and retaining the team members has become one of the major influencing factors for successful project development in the mining industry in the last decade.Increasingly, international teams are being established combining skill sets, subject matter experts, unique previous experiences and diverse cultures to deliver mining projects all around the world.This paper explores the characteristics of a highly effective team, the communication and geographic challenges and some potential pitfalls which influence the ability to form effective teams within the mining industry.CITATION:Ebbels, A M and Pratt, D, 2012. A great project team - Bringing together location and culture, in Proceedings Project Evaluation 2012 , pp 197-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By M Ozkayhan, N Arslan

"The Efemçukuru underground mine in western Turkey is an intermediate sulfidation, epithermal gold deposit. The bulk of the mineral resources and all of the mineral reserves lie within the Kestanebeleni (KB) vein system. This system comprises four spatially-distinct mineralised zones: the south ore shoot (SOS), the middle ore shoot (MOS), the north ore shoot (NOS) and the KB north-west ore shoot. Production currently occurs only in the SOS, MOS and NOS zones. The gold mineralisation is very fine grained and occurs as free grains in quartz and carbonate, and as inclusions in sulfide minerals. Gold is recovered as part of a sulfide concentrate by flotation methods. Though hosted in the KB vein, the gold mineralisation is not evenly distributed within the veins. Definition of its occurrence is totally dependent on diamond drilling.Diamond drilling at Efemçukuru is done with its own equipment and staff, all managed by the mine geology group. The process over the mine’s six year production history incorporates continual improvement with an innovative approach by focusing on the following: drill team organisation career development and training product research and effective equipment management cost reduction planning and scheduling of development for drill stations.Over 40 000 metres of mostly BQ size core are drilled annually by three drill rigs at a cost approaching US$35/m.The planning and execution of the drilling pattern depends on the configuration of the ore shoot and the planned mining method. Ore extraction is mainly by drift and fill mining augmented by about 15 per cent longhole stoping. The drilling of a specific area is scheduled to be finished 3 to 8 months prior to mining. This scheduling is sufficient for short-term grade model updates and any needed changes to the planned development or stope sequencing prior to planned production from the stope area.CITATION:Arslan, N and Ozkayhan, M, 2017. Diamond drilling at Efemçukuru gold mine, Turkey – a case study on the benefits of timely and cost-effective drilling to short-term planning, in Proceedings Tenth International Mining Geology Conference 2017, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By T Burns, P Savory

In 2013, Rio Tinto Iron Ore (RTIO) produced 251 Mt from 15 mines in Western Australia. Throughout the mines, Ore Reserve models are used for long-term and medium-term mine planning. Grade control data aids the accuracy of short-term planning. Reconciliation of models with grade control data is important for maintaining confidence in predictions from the models, understanding the limitations of the models, and identifying issues that may require further work.There are a large number of sites and models, with more than 200 professionals involved in different parts of the reconciliation process. Regular meetings of all involved and enabling effective communication are important in the reconciliation process.Reconciliation data is gathered and processed through a web-based system; Grade Block Reconciliation System. This system cuts each grade block against the required model, stores the results, and allows users to view and analyse the data. Development of this system has occurred over a number of years and all Rio Tinto Iron Ore mine geologists and resource geologists now use it as standard to report reconciliation results. The results can be viewed in many ways including by different time periods or benches. Graphing the results assists identification of trends. Centralising and standardising reconciliation has allowed easier comparison between sites. Flexibility in the system allows users to customise reports to manage issues unique to their particular site.In parallel with system development, substantial effort has been put into ensuring mining professionals get together to discuss and understand reconciliation issues. To facilitate this there are now regular sessions, including site visits. Issues are assessed on a case-by-case basis and decisions on how best to address the issues are made by the relevant stakeholders. Reconciliation reports and action plans are revised each quarter.CITATION:Burns, T and Savory, P, 2014. Reconciliation of orebody model predictions – system and people, in Proceedings Ninth International Mining Geology Conference 2014 , pp 367–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014