Search Documents

By Fernando N, Guang LX

Brown coal in Victoria in spite of its substantial reserves is not utilized greatly because of its high moisture content(-65% w/w). Transportation and handling costs of raw brown coal, on an available energy basis are so expensive that 93% of production is burnt for electricity generation on or adjacent to the coal deposit in Victoria. With direct firing of moist brown coal in power stations, approximately 20% of the gross calorific value of the fuse is used to evaporate the water contained in the coal. This energy is lost as vapour with the flue gas which is vented to the atmosphere. Also there is a 25% increase in flue gas volume and the size and cost of most of the units through which it passes must be appropriately larger. Since there are large quantities of water present the flame temperature is significantly reduced. For zero excess air and no air pre-heating the theoretical flame temperatures are: 609'o wow moisture 1450¦C 40% ª ª ª 1790¦C ZOO ª ª ª 1990¦C As a result of this there is a reduction in radiant heat transfer leading to a requirement for a two fold increase in radiant tube area. A boiler of much greater size and cost is thus required to house the additional tubes. Figure 1 illustrates the relative sizes of a boiler fired with 60% moisture brown coal with a boiler or similar output fed with a British bituminous coal, 14% moisture.

Jan 1, 1989

By Yanagase T, Nakamura T, Ueda Y

The possibility of removing the phos phorus and sulphur contained in steelmaking slag has been studied by observing directly through the microscope melts heated on Pt- filaments. After a CaO crystal was placed in the molten slag, distributions of P, S and other elements formed around the CaO crystal were determined with the aid of EPMA. The results indicated that a layer of 2CaO SiO2 is formed on solid CaO in CaO-Si02 melts. Then between CaO and the newly formed compound the molten slag tends to migrate through cracks. For higher Fe 2 03 contents, the layers of the compounds 2CaO.Si02 and 3CaO SiO2 formed around the CaO crystal are not continuous but look more like particles, which promotes the dissolution of CaO. Phosphorus in slag was found to be enriched in the 2CaOòSi02 layer. Phosphorus in the 2CaO SiO2 phase is not related to the primary slag composition, being about 5-7% P205.. Sulphur in slag,as well as the phos- phorus,was concentrated in the 2CaO.Si02 phase. Disintegration due to weathering observed for slags produced in these investigations appeared to be due principally to hydration of lime.

Jan 1, 1980

By Valery W, Morrell S, Loughlin P, O&apos

Traditionally, blasts in mining operations are designed to prepare the in situ rock mass for excavation and transport without much consideration being given to the downstream comminution processes. Blasting is in fact the first step in a chain

Jan 1, 1998

Techniques and results achieved during the excavation of the Melbourne Underground Rail Loop (HURL) are summarised and discussed in the context of the various restraints present in a typical urban construction project. Mechanical methods (as distinct from those utilising blasting)accounted for the bulk of the excavation. Ground support was critical in this particular geological excavation setting, but is not discussed in detail except insofar as it constitutes a restraint to excavation progress.

Jan 1, 1978

In Australia, current production of rare earth element (REE) minerals, monazite and xenotime, occurs as by-product from titanium-enriched placers and beach sands. Undeveloped REE resources are associated with carbonatites, alkaline igneous rocks, pegmatites, phosphorites, cemented fluvial sandstones, and uranium mineralisations. The REE are held within a range of minerals including silicates, phosphates, a1uminophosphates, carbonates, and oxides. The development of these REE resources may require new processing and extraction methods. The distribution of REE in the currently mined ore minerals, monazite and bastnaesite, does not match that requested by the market. Exploration for new REE resources should be focused on ores with more marketable REE distributions, particularly with heavy REE, neodymium, samarium, europium and yttrium enrichments. Such ores occur within alkaline igneous rocks, in laterites overlying carbonatites and alkaline igneous rocks, and in placers derived from low-grade regional and contact metamorphic sediments. Lateritic REE deposits may be easily and economically mined by shovel in open pits and are unlikely to require extensive crushing and milling. In addition, lateritic REE clay deposits may be processed by simple hydrometallurgicaltreatment mehtods.

Jan 1, 1991

Spatial continuity as described by a variogram is a reflection of the underlying mineralisation/geology. Modelling of the spatial continuity (variogram) must account for both the quantitative data (ie sample grades), on which the variogram calculations are based, and the qualitative information as provided by the geological interpretation. An understanding of the geology and the variogram interpretation tie together the sample values and allow us to go beyond the actual data (Journel, 1995). Variography makes geology transportable and allows the geological interpolations to be channelled downstream into mine planning, ultimately affecting the economic decisions surrounding a deposit. As such the process of variography and resource modelling is critical. Thus consistent expert decisions need to be made which force geologists to have a closer look at the available information and the geological interpretations. The aim of this paper is to provide an overview of the latest developments in visualising variography and to demonstrate their usefulness in decisions regarding the spatial continuity of mineralisation. New ideas concerning potential future developments in visualising and modelling spatial continuity through variography are introduced.

Jan 1, 1996

By A Tomsett, J Rutter

Ore control systems at Ridgeway have been designed to deliver gold and copper metal production through focussing on the ore characteristics that impact on mine and mill performance and ultimately metal delivery. This is achieved using data collection and management systems which allow data to be collected digitally with æat captureÆ validation routines. This data forms the basis of forecasting systems which aim to accurately assess local in situ and drawn ore characteristics. Physical attributes of ore such as draw characteristics, brow conditions and visual grade estimation are rountinely recorded. Ore tracking and accounting systems monitor gold and copper grade, copper mineralogy, host lithology and ore sizing. These have material impacts on concentrator throughput and metal recovery. Routine reconcilation and check sampling allow calibration of these systems.

Jan 1, 2002

By Jagger N. D

Lead residue from the Zinc Leach Plant at Pasminco's Port Pirie Lead Smelter was previously filtered on a vacuum drum filter and further dried in a gas fired rotary kiln prior to stockpiling and transport to the Sinter Plant. This process involved several materials handling stages, recycled significant amounts of zinc and often resulted in poor environmental conditions. These problems have been overcome by pumping the thickened leach residue approximately 450m to the Sinter Plant where it is filtered in a Larox Automatic Pressure Filter. The filter cake is discharged onto a conveyor belt, held in a storage hopper and then fed directly to the main sinter plant feed stream. Filtrate is returned to the process for additional zinc recovery. The laboratory and pilot plant filtration results are briefly discussed and compared with the operating plant data. The filter installation and ancillaries are described in detail along with the commissioning, operating and maintenance experience over the past 4 years. This installation has overcome the environmental and materials handling problems and resulted in annual savings of approximately $1 million.

Jan 1, 1989

The paper describes a computer model developed within the State Electricity Commis- sion of Victoria for use in open cut planning. The purpose of the model is to simulate all the typical occurrences in, and influences on, the coal supply and overburden disposal systems in order to be able to assess their performance. The model incorporates much of the long term and day-to-day operations planning logic required for the allocation of resources within an open cut. This logic takes account of power station demands, bunker stocks, plant and crew availability, the balance of reserves between dredgers, planned maintenance, etc. The perfor- mance of plant within the system is simulated using random selections from statistical distri- butions of Time to Failure and Time of Failure for each plant item. The application of the model in selecting a suitable bunker capacity in a notional open cut development is described to illustrate the potential of the model in optimising plant selection.

Jan 1, 1982

By Hall S, Upton D

WMC Resources Ltd nickel operations have expanded significantly over the last three years. Production capacity has increased at mine/concentrate, smelting and refinery processes to such an extent that WMC now ranks within the top three or four producers of nickel metal in all forms. The stainless steel industry remains the dominant user of nickel. WMC's forecast is for stainless steel production to grow at 2.8 per cent per annum off of the 1995 peak, with much slower growth in the short-term as the stainless steel inventory overhang unwinds, followed by a return to higher trend growth rates. WMC's forecast for the long-term growth in demand for primary nickel is three per cent per annum off the 1995 peak; again, slower growth in the short-term before a return to higher long-term trend rates. This projection is towards the optimistic end of the range of industry experts. It equates to a requirement for new primary nickel of 25 000 to 30 000 tonnes of annual capacity each year.

Jan 1, 1996

By S Shipard

Filters are used in water treatment and hydrometallurgical process plants for objectives such as generating a dry spadable solid, pumpable high density slurry or high purity filtrate. The priority objective of every polishing filter, sometimes also termed clarifying filters is high purity filtrate and these are found in many diverse industries and even different applications within the same industry.To generate a high purity filtrate, process designers have the choice of many different polishing filter products, but in reality very few polishing filters are based on fundamentally different filtering concepts.This paper reviews the technology merits of well-known and the more recently developed polishing filter products and aims to assist metallurgists and engineers with the selection of an appropriate polishing filtration technology for pregnant liquor filtration and other process applications, plus a guide to best practice.CITATION:Shipard, S, 2013. Polishing filters for mineral processing plants, in Proceedings MetPlant 2013 , pp 118-125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

INDEX OF CONTENTSIntroductionThe slag samplesGranulated SlagGlass-spinel-magnetite-metallic leadRapidly Chilled SlagSlowly Cooled SlagSpinel - magnetite - zinc melitite (hardystonite) willemite - olivine -lead silicate - metallic lead - lead sulphide - copper sulphide - copper arsenide - nickel arsenide.ConclusionsIllustrationsINTRODUCTIONThis paper presents the results of a mineragraphic examination of representative samples of granulated lead blast furnace slags from the Port Pirie Smelter, and of slowly cooled samples of t:b.e same slags, undertaken at the request of the Broken Hill Associated Smelters Pty. Ltd., as part of the research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organization.THE SLAG SAMPLESThe chemical composition of the slags examined is given by the following three analyses of the granulated slags, supplied by the Broken Hill Associated Smelters (Table 1).

Jan 1, 1949

By L Soares, W T. Hennies, F Fujimur

Barra Bonita reservoir, located in the Sao Paulo State, Brazil, has been mainly used for local navigation and electricity generation to supply a prosper region in the country. Sand mining activities in that area have an important social and economic meaning for the local community. In this reservoir there are several sand mines that produce around 45 000 m3 of sand a month. These deposits were rich in material used as concrete aggregate in the civil construction. However, nowadays a significant increase in the demand of gravel can be observed, representing a serious productive problem. This material hasnÆt been well accepted by the market and, through the years, it was disposed at open sky in piles as waste deposits. This deposits have caused environmental problems like visual impact, reduction of free spaces outside and inside the mine, source of material to erosion and sedimentation processes in lower areas, flooding as a result of the filling up process in the drainage system, among others. For a lack of an appropriate technological characterisation, this material have been mainly used to pavement internal and external areas in the mine, with lower cost associated. With the purpose of evaluate the usefulness of this material in the conventional concrete, there were conducted several tests in the disposed residue including petrographical, physical, and chemical characterisation. The petrographical analysis and the preliminary results of the study showed that the material reacts with the alkalis that are present in the conventional cement (CP-II-E-32). In order to make the application technical and economically possible a research was developed seeking forms to correct this characteristic by adding special cements with high pozzolana content. The results of the technological, physical and chemical characterisation of the products indicated the technical viability of the use of that material. The study also allowed projecting environmental improvements resulting in the elimination of the waste piles.

Jan 1, 2003

Mining is a high risk, high capital and potentially high reward undertaking. A large proportion of the risk comes from a lack of definition of the orebody (which also provides some of the potential) and the unpredictable nature of the market. This makes the planning process difficult but encourages the development of a robust yet flexible mining system. The system should be capable of absorbing some deviation from the anticipated concept without a significant impact on profitability. The mine planning process tends to consist of a series of related but discrete stages. For instance, the pit shells are designed, a schedule for the pit shells is created, a plant fleet is chosen to achieve the schedule and a financial analysis is carried out on that scenario. It is likely a few iterations are carried out using various mill throughputs to produce a favoured financial result. The problem is that handing results from stage æBÆ for use in æCÆ doesnÆt encourage a flexible system. æCÆ is likely to be built for exactly æBÆ. Unfortunately, in mining, æAÆ (the orebody) has the highest potential for variability and impacts everything else downstream. æDÆ the market also has high potential for unplanned variability. These variations can spread and æreverberateÆ through the whole mine process. For example an unexpected increase in ore oversize impacts all downstream mine processes to the primary crusher which may in turn create problems back æupstreamÆ by restricting throughput rate. Also an unexpected drop in demand or price could require modifications to the planned production rates. This paper looks at how mining process simulation can be used to support the development of strategies to counteract unforseen circumstances or alter production to match fluctuations in demand and price.

Jan 1, 2003

By Fair A, Oxenford J

Syncrude Canada Ltd operates one of the largest open pit mines in the world at Fort McMurray in northern Alberta, Canada. In 1993, Syncrude mined and processed 131.2 Mt of oil sands to produce 67.0 MBbls of synthetic crude oil (SCO). This represents approximately 13 per cent of Canada's crude oil requirements. In addition to the oil sand mined, Syncrude moved approximately 96 Mt of overburden ahead of the mining operation in 1993. Since start-up in 1978, Syncrude has had outstanding success in improving the safety and reliability of its operation. Much of this success has been achieved by reducing risk through the application of new and improved technology. This improved safety and reliability has resulted in, among other things, very significant improvements in operating costs and profitability. This paper discusses some of the technology applications that have been introduced at Syncrude to reduce risks to people, equipment, operations and the environment. Three specific examples will be discussed in detail to demonstrate how reductions in risk have greatly improved the operation.

Jan 1, 1994

By Milawarma E, Cusack C

The Sapan Dalam coal deposit of Indonesia consists of ten steeply dipping seams with thicknesses varying between 0.1 and 3.5 m and split by shale, clay, silt and sandstone. The area contains four faults dipping about 75¦ with four to 85 m vertical displacements. The complex nature of the deposit coupled with limited 27 exploration drillholes at an average spacing of 200 m made it difficult to create a realistic geological model. A three-dimensional gridded seam model gave a fair representation of the deposit. Attempt to create an optimum pit using the WHITTLE 3D pit optimiser proved unsuccessful since the pit optimiser is restricted to standard regular or fixed blocks. The gridded seam model was converted to a fixed block model prior to the optimum pit design. Smoothing and pit base controlling were also introduced to obtain a smoother pit. A mining scenario produced 3.6 million tonnes of coal, 28.4 million bcm of waste and US$18.1 million revenue.

Jan 1, 1995

By R T. A MacGillivray, S B. Curtis

Bacteriophage (phage) are viruses that infect bacteria. Protein coatings on the surface of the phage particle can be genetically engineered so that they bind to inorganic molecules. The filamentous phage particle is about 930 nanometres in length and 6.5 nanometres in diameter and consists of a single-stranded molecule of DNA surrounded by five different coat protein molecules denoted P3, P6, P7, P8 and P9. Peptide sequences in the P3 coat protein that bind to sphalerite and chalcopyrite have been identified. The binding is selective; phage with specific P3 peptide sequences bind to minerals but do not bind to silica or to pyrite. Two peptide sequences in the P8 coat protein that bind selectively to chalcopyrite and pyrite have also been identified. The amino acids in the P8 binding sequences are hydrophilic and thus a coating of a mineral particle with phage having these peptide sequences may render the particle hydrophilic. Experiments are underway to confirm this. Phage are relatively easy to grow and are not living organisms requiring an energy source to maintain life. Phage can also tolerate a range of pH and temperatures. Given this, and the ability to indentify phage coat proteins that bind selectively to a variety of inorganic molecules, phage have the potential to be useful tools in mineral processing and waste treatment.

Jan 1, 2008

By Paley N, Cameron A, Townson P

Although blasthole deviation is a problem which can seriously affect blasting operations, there is little practical emphasis on controlling this deviation and no practical emphasis on understanding its practical behaviour. The most common way of dealing with it involves tight control over drill set up and surveying hole paths. The surveying might involve simple collar location and inclination measurement to estimate the hole's actual path. At best, some operations routinely survey hole paths after all holes in a stope have been drilled. In addition, although there is an expectation that holes will deviate, there is no planning for this behaviour in order to reduce its impact on the blast. Design decisions are invariably made with the assumption that holes are straight. If and when surveys reveal problems it is possible only to adjust charging and initiation to 'work around them'. In extreme cases the drill might be recalled to fill in gaps. The lack of planning and the lack of understanding are doubtlessly linked.A model is presented that will predict the expected path of a drill hole. By knowing how a selected few holes deviated it is possible to make a good estimate of the deviation of other holes in the same rock mass. After minimal calibration the model can be used to increase the amount of information for a given amount of surveying or the amount of surveying can be reduced while maintaining the same level of knowledge of blasthole deviation. Equally important is the ability to plan for the deviation in future drilling through altering the initial collar angles or drilling from different locations. It is the authors' hope that planning for hole deviation becomes as much a part of the design process as planning for detonator delay scatter and explosive performance variation.

Jan 1, 1992

By Firmin K

The Mt. Tom Price orebody of Hamersley Iron Pty. Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the orebody, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control'of products based on selective mining is the production of advance data, on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades Are determined from assay of samples taken from blasthole cuttings.

Jan 1, 1980

By Gresham J. J

The rapid and successful development by Western Mining Corporation Limited (WMC) of a gold mining industry based on the deposits of the Kambalda-St Ives group, was the final chapter in a story that started some 85 years earlier. Although the exploration work that led to the development of the current mining operation took place in the 1970s and 1980s, the successes had their roots in the 1890s and it took three gold rushes, and separate uranium and nickel exploration booms to make the discoveries Possible.

Jan 1, 1991