Search Documents

By K Williams

Marvel Loch South Pit has had a number of stages of open and underground mining activities before acquisition by Sons of Gwalia. The historical pit had achieved a completed pit depth of 150 metres and the shaft and decline mine had reached approximately 220 metres in depth using open stope mining methods. The various mining methods reflect the various economics and industry practice at the time. The South Pit ore zones are medium grade (~2.5 g/t) but have a regular geometry and large tonnes per vertical metre. A number of studies have been completed up to a pre-feasibility stage looking at options to extend the pit depth and to lower the unit cost of gold production. The options considered were the re-optimisation of the pit to determine further cutbacks or the innovative use of an in-the-wall ramp. The in-the-wall ramp (tunnel) would permit the removal of the in pit ramp to expose additional ore that was within the footprint of the ramp design and to provide the opportunity to increase the final pit depth. Similar mining method has only been used at Three Mile (Coolgardie, WA) and Chalice Mine (Norseman, WA). The tunnel would serve as a gateway for further extension of the south mine and the central ore zone via underground mining methods. The ultimate depth of the South Pit has been extended to 310 metres below surface and significant additional ore has been recovered. This paper will give an insight into the various studies to optimise the Tunnel mining method, the determination of the various tunnel dimensions, and the phases of mining to arrive at the completed design.

Jan 1, 2003

By Tullemans FJ

This paper describes the general approach to ore reserve estimation and mine planning used at the Kidston Gold Mine. The geological setting and exploration is briefly summarized for background information.A geostatistical study of the deposit was carried out to determine the geological ore reserve. This was confirmed using a manual polygonal technique. Optimum pits outlined by a Lerchs-Grossman open pit design algorithm were manually smoothed allowing mineable reserves to be calculated. Mine production schedules based on kriged block grades and tonnages are continuously updated using production blasthole assays. An arithmetic mean technique of block grade estimation has proved successful to date. After milling approximately 4.9Mt of ore, the mill grade of 2.13g Au/t is only 0.5% above the mine estimate of 2.12g Au/t. The difference in contained gold between "As staked" blasthole reserves and kriged mineable reserves is 3.8%. The application of blasthole kriging as a basis for ore/waste classification in erratically mineralized areas is being evaluated. Planned future developments are briefly mentioned.

Jan 1, 1986

The Knelson Concentrator is a centrifugal gold concentrator developed in Canada, which utilises the combination of high gravitational ("G") forces and a unique fluidising action to efficiently recover free gold particles from minus 6 mm to fine micron gold in both alluvial and hardrock applications.Operating parameters including water requirements, fluidising pressures and feed rates are given, as well as an indication of their various effects on gold recovery.Results include a Colorado School of Mines Research Institute (CSMRI) report comparing the Knelson concentrator with various other gravity concentrators.

Jan 1, 1984

A review is presented of techniques cur- rently in use, or being developed, to enable the determination of virgin rock stress at consid- erable depth (> 1000 m) from small diameter sur- face drill holes (

Jan 1, 1975

By Shugen T

Due to the increase of passenger traffic, a new station is proposed which is about 6.8km from south station. An underground connection line is under feasibility study for connecting these two stations in order to avoid the in- terference with surface traffic. In this paper the traffic condi- tion and the geological formation along the planned route will be described and analysed. Different methods of con struction have been proposed and dis- cussed such as shield method, slurry wall method etc. In this paper compari- sons are made among these methods and advantages and disadvantages given. The authors proposal to construct this connection line by NATM raise wide

Jan 1, 1987

By R Lurf, C Weber

In the frame of this paper a holistic dynamic process model approach is presented in order to introduce operational and technical excellence in drilling and blasting. Both on a macro and micro level the single process parts of drilling and blasting are outlined and their interaction is explained. The use of this approach for closing the gap between process planning and process implementation is explained and an example of the value generated is given.

Jan 1, 2007

In southeastern China, offshore Tertiarybasins are buried underneath the broad continental shelf areas from Taiwan to Hainan Island. These basins bear relatively similar characteristics of structure, stratigraphy and tectonics. Based on age and tectonic framework, these Tertiary basins are divided into two groups of Paleogene basin and Neogene basin (Fig.1 and 2). However, observations of extensional structures indicate that the Paleogene basins are rift basins; and the predominant structural features are NE-SW trending half grabens and fault blocks. In a regional scale, these half grabens and adjacent uplifts represent a horst-and-graben structural style. Neogene basins are downwarp basins lying on the tilting continental shelf. Late Tertiary sequences are relatively undeformed but locally with minor folding and thrusting during the Pliocene-Pleistocene.Seismic stratigraphy and well data indicate that the Early Tertiary strata are commonly tilted and disturbed as nonmarine to marginal marine facies deposited in the wedge-shaped half grabens; the Late Tertiary strata are generally parallel undisturbed marine facies accumulated in the enlarged downwarp basins overlying the infilled half grabens. In general, three major regional unconformities formed during the Late Cretaceous, the Late Eocene and the Middle Miocene. Widespread extrusive basaltic flows are commonly associated with these unconformities.

Jan 1, 1990

By Roberts M. L

Long Shaft was initially developed using a rail haulage system on every working level comprising battery electric locomotives and granby trucks loaded by rail mounted rocker shovels. Production was commenced using conventional hand held cut and fill mining methods. In an effort to improve productivity and reduce operating costs a mechanised cut and fill stoping method evolved to suit the wider sections of the orebody. To further improve productivity and reduce costs the mechanised levels of the mine are progressively being redeveloped to enable the use of trackless diesel haulage equipment. An added benefit of trackless haulage equipment will be the ability to place development mullock into stopes as Fill.

Jan 1, 1988

By P D. Fraser

This paper examines the new water-hydraulic (hydro powered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef, hard-rock South African mines. These include - drill rigs for flat end tunnel development, narrow inclined raises and winzes, large inclines and declines and long hole based developments such as orepasses and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed air powered, hand-held development are generally more cost effective than imported oil electro-hydraulic drill rigs. Furthermore, hydro powered rigs are inherently energy efficient. The benefits of hydropower are discussed and a æcomprehensive development modelÆ is presented which demonstrates that orebodies can be accessed in significantly shorter times. æLocalisedÆ half level hydropower systems are introduced and a range of ancillary equipment available is listed.CITATION:Fraser, P D, 2012. The use of high-pressure, water-hydraulic (hydropower) technology in South African narrow-reef, hard-rock mines, in Proceedings Narrow Vein Mining 2012 , pp 229-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Mullens P

Recent advances in technology have allowed many of the problems of directional control of long diamond drill holes to be overcome. Three case histories are presented, from Cobar, Hilton North and Mount Isa Mine, in which careful hole design and the use of wedges and down-the-hole motors have allowed tight directional control of drilling. Substantial savings in time and cost were achieved in all three cases.

Jan 1, 1990

By Just G. D

The results of a geostatistical analysis of geochemical data obtained from field measurements are described in the paper. Q values derived from seismic signal rise times for different travel paths in the rock masses were used in the study. Cross-hole seismic measurements made at surface and underground sites formed the basis for the work. Geostatistical estimation of average l/Q values for area of the rock were compared with geological interpretions of rock type distributions. Reasonable correlations were obtained between the two methods of rock quality estimation.

Jan 1, 1988

The mine planning and operational aspects of applying Continuous Surface Miner (CSM) technology to Australian coal strip and open cut mines is investigated for both existing and planned deposits. CSM produc- tivity as a function of geomechanical properties, formation thickness, mechanical availability and in-pit physical constraints, are considered. Productivity and operational costs are derived from current production machines and from first principles.

Jan 1, 1989

By Korsch RJ

Permian oroclines in eastern Australia must have formed by sliding on a detachment surface. It is identified as a westward- dipping Devonian and Carboniferous sub- duction zone. Major strike-slip faults probably sole out on the same surface. One major fault with an associated serpentinite belt was pulled away from the craton abd bent into loops. Basins formed in the loops.

Jan 1, 1987

By D Dickson

The properties along Ida Avenue in Mosman stand 10 m above the road on an outcrop of Sydney sandstone. Access to the houses is generally via a long steep staircase. The owner of 22 Ida Avenue identified an opportunity to use the natural strength of the rock beneath his property to excavate an underground garage and to provide access to the basement of his property via a 10 m elevator shaft from the back of the garage. This paper will describe the design and construction of this unique and innovative urban development.

Jan 1, 2008

The Queensland Magnesia Project is based on a unique cryptocrystalline nodular magnesite orebody which required an innovative approach to process design in order to economically exploit the characteristics of the ore and produce a marketable range of high quality refractory magnesias for a declining world market. High quality natural refractory magnesia must have an MgO content in excess of 95 per cent with a very strictly controlled content and ratio of residual impurities such as calcium, silica and iron. The natural products compete with magnesias derived by chemical extraction from sea water or brines which exhibit very high purity but often lack other characteristics which are of value to refractory brick makers. Since start up in late-1991 QMAG has achieved a remarkable market penetration for both its deadburned and electrofused products with sales for the 1993/94 financial year representing 92 per cent of deadburned capacity and 138 per cent of original electrofused capacity respectively, all at a time when the world steel industry has been in recession.

Jan 1, 1995

By Pollard D. M

In the batch phase disengagement test, an organic and an aqueous phase are mixed together for a known period to produce a dispersion which may be either organic continuous (aqueous phase droplets) or aqueous continuous (organic phase droplets). The continuity of the dis- persion will depend upon the method of init- iating the dispersion, the conditions under which the system is operating, such as temper- ature and impeller speed, and the properties of the liquids, such as viscosity, inter- facial tension and solute content. Once the dispersion has been agitated for the required period, the agitator is turned off and the position of the coalescence interface and the sedimentation interface recorded as a function of time. This will produce a plot similar to Figure 1, where the overall dir- ection of travel of the droplets of dispersed phase is away from the sedimentation inter- face and towards the coalescence interface where the droplets coalesce with the homophase.

Jan 1, 1987

The introduction of on-stream analysis in flotation circuits has raised the possibility of automatic control of flotation performance by digital computers. The development of control strategies for an industrial zinc cir- cuit is discussed with reference to identifi- cation of the major disturbances, investigation into the performance of the circuit, the design of the control algorithms, the testing of their performance and their implementation in a production environment.

Jan 1, 1983

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

The Kidston Gold Mine i s located in northern Queensland some 2 Ukm northwest of Townsville. I t is the largest gold mine in Australia and produces approximately 25 percent of Australia's gold and one percent of the world's gold.Initially, traditional mining industry management approaches resulted in the rejection of what appeared to be an attractive low-grade deposit as an uneconomic proposition. Critical re-examination revealed that the rejection was based upon managerial inflexibility and traditionally over-conservative methods of mine evaluation, construction, operation, projected commodity prices and contingency factors. "Ihus it tradition was to prevail, the Kidston prospect would never have been realised.

Jan 1, 1985

By Armstrong G. J, Bowling K. McG, Gray C. H

An experimental induration facility has been developed and used for conducting iso- thermal tests and plant simulation studies on the thermal induration of iron ore pellets. The influence of time, temperature, lime content, ore type, shale content and particle-size dis- tribution (e.g. Blaine Index) is being studied in a continuing programme. The present paper deals with experiments relating to the first three of these parameters and illustrates the use of an experimental design suitable for statistical analysis. The relations between isothermal data and the results of complete simulation rests are discussed.

Jan 1, 1973