Search Documents

By P. J. Gron

"The Samatosum Project is a base and precious metal deposit located in south central British Columbia. A dilute ore reserve of 766, 682 tonnes grading an average 1.1% copper, 3.0% zinc, 1.4% lead, 833 gram per tonne silver and 1.6 gram per tonne gold is available. The base metals occur as tetrahedrite, chalcopyrite, sphalerite and galena. Virtually all of the silver and gold are associated with the tetrahedrite.The mill is operated at a rate of 21 tonnes per hour. Sulphur dioxide is used as a zinc depressant in the grinding circuit. Production of a Cu/Pb/Ag concentrate is accomplished by conventional flotation. This concentrate is then separated into Cu-Ag and Pb concentrates through a reverse flotation circuit utilizing sulphur dioxide, starch and sulphuric acid as lead depressants.The tailings from the Cu/Pb/Ag circuit are treated with copper sulphate to activate the zinc. Production of a zinc concentrate is accomplished by conventional flotation. Dewatering of the concentrates to 6% moisture is done with a LAROX filter press.Tailings effluent is treated with lime and sodium sulphide to precipitate out the heavy metals. The resulting sludge is treated in OYNASAND sand filtration units to produce a quality effluent."

Jan 1, 1990

By Erin N. Legault-Seguin

The Lac des Iles Mine (LDI) is located approximately 100 km northwest of Thunder Bay, ON. The mine has been in operation since 1993. The initial mine production was 2,300 mtpd and increased to 15,000 mtpd following a mine expansion project that was completed in 2001. Effective Oct. 29, 2008, LDI was shut-down under care and maintenance due to low metal prices. Prior to shutting down, LDI was the only primary PGM deposit in operation in Canada and of the few found globally. The complex geology and physical properties of the deposit causes several challenges for the concentrator. This paper will discuss the solutions to the main challenges of attaining nameplate tonnage and achieve satisfactory Pd recovery and concentrate grades.

May 1, 2009

By Timothy R. Eby

"The Wabush Mines project was formed in 1956 to develop a large iron ore property in Western Labrador. The town of Wabush along with the mining and concentrating facilities are located 640 air miles from Montreal, and 734 air miles from St. John's. The operation has been in production since late 1964.While mining and concentrating operations are located in Labrador, the pelletizing facilities are situated 275 miles south at Sept-Iles, Quebec. Dedicated in 1965, Wabush produces six million tons of high quality iron ore pellets annually. The company employs 1, 550 people at Wabush and the Pointe Noire plant at Sept-Iles.Wabush Mines is an unincorporated joint venture of three companies -The Steel Company of Canada, Dominion Foundries and Steel Ltd. and the remaining 58% by the Wabush Iron Co. Ltd. Wabush Iron Co. Ltd. is in turn owned by six companies: The Youngstown Sheet & Tube Company, Inland Steel Company, Interlake Inc., Wheeling Pittsburg Steel Company, Finsider International S.A. and Pickands Mather & Company which is also managing agent.The town of Wabush is set in a remote part of Northern Canada accessible only by rail and air transportation. But this in no way has hindered the growth and development of the area. Modern housing units, shopping facilities, airport and of course, recreational facilities are all patt of every day living amenities, an accepted aprt of southern communities, but quite unique for northern isolated mining localities."

Jan 1, 1978

By Norman O. Lotter

Drill core is preferred as the sample material for metallurgical and mineralogical characterisation and flowsheeting of an orebody. The question arises as to how to do this at the economic optimum, since geologists have several other strategic uses for their drill core. The limiting factors are the cost of extra drilling for the metallurgical testwork and the need to preserve the drill core record. In this study, the representative sampling of drill core at an economic optimum for metallurgical testing is addressed. This phase of the drill core work is preceded by earlier drill core characterisation - for which other appropriate sampling protocols are used - that has provisionally categorised the orebody into geometallurgical units. In stratified sampling of drill core, use is made of a version of the stratified approach to compound distributions proposed by Cochran in 1946. Use is made of Gy’s 50-piece minimum sample mass model to estimate minimum requisite sample mass. In the case where sampling and testwork are required on a Lifeof- Mine blend of a given ore deposit, whereby defined ore types or geometallurgical units are present, the sample mass requirement is significantly reduced by working from drill-core at the geometallurgical unit level. A case study using Raglan drill core is discussed. Using nickel as an indicator paymetal, and sampling at a fundamental variance level of 8%, the minimum sample masses for disseminated sulphides, net-textured sulphides, and massive sulphides are 3.80, 7.37 and 4.39 kg respectively. When the same drill-core is sampled as a Life-of-Mine mixture without knowledge of the geometallurgical units, the minimum sample mass increases to 84.28 kg. It is thus possible to assemble a representative Life-of-Mine sample of drill-core more economically, at the same time validating its representativity. Equivalent calculations for copper, platinum and palladium are discussed, with outcomes consistent with this finding. When all four paymetals are considered, one selects the largest minimum mass out of all four cases. This results in minimum sample masses of 11.67, 74.90 and 175.16 kg for disseminated sulphides, net-textured sulphides and massive sulphides respectively. The simulated Life-of- Mine blend would require a minimum sample mass of 377.33 kg to cover all four paymetals.

Jan 1, 2010

By G. S. Dobby, J. A. Finch

"I. INTRODUCTIONA significant development in flotation over the past few years has been the increasing industrial use of flotation columns, primarily in Canada. The column differs dramatically from conventional mechanical flotation machines, both in design end operating philosophy, which has been a principal reason for its slow acceptance by the mineral industry. Boutin, Tremblay and Wheeler (1. 2) developed the concept in the early 1960's and since then plant and laboratory columns have been marketed commercially by Column Flotation Company of Canada Ltd. In 1980-81 at Mines Gaspe, Quebec, three columns replaced 13 conventional cleaners in a molybdenum upgrading circuit, with superior results (3). Since then many of the copper producers in British Columbia have installed columns for copper and molybdenum cleaning, including Gibraltar, Lornex, Highmont and Island Copper. There now appears to be widespread interest in flotation columns.The column is particularly attractive for applications involving multiple cleaning stages and can upgrade In a single stage compared with several stages of mechanical cells. This results in simpler, more controllable circuits. Importantly, the column itself is well suited to computer control. A significant problem, however, has been that of translating laboratory data to plant performance. The purposes of this communication are to address the problem of column scale-up and to describe some of the transport mechanisms of a flotation column, leading to a kinetics based model.A schematic of a flotation column is shown in Figure]. Industrial columns are up to 13 m high and 0.3 to 1.8 m in cross section (either square or circular). Three zones can be identified:a collection zone, with feed entering 2 to 3 m below the top of the column and descending against rising bubbles generated at a gas sparger; a washing zone, where a packed bubble bed is generated by a downward flow of wash water; and a conventional froth (2 - 5 cm thick), the sole purpose of which is particle transport to the launder. The tailings withdrawal at the bottom of the column is controlled at a rate slightly greater than the feed flowrate (called a positive bias).An important element is the washwater, added just below the froth zone. The component of the washwater that flows downward (to make up the bias) is sufficient to prevent coalescence of rising gas bubbles. The packed bubble beg so generated is very efficient at suppressing gangue entrainment to the concentrate."

Jan 1, 1985

By Elaine Ellingham, Francis T. Manns

"Abstract -The Orostar and Scadding were two small gold mines owned and operated by Orofino Resources Limited. Conventional statistical treatment indicates an identical arithmetic mean grade of 0.22 oz/T Au for both mineable reserves. Further, the deposits are both shown to have cut weighted average reserve grade of 0.21 oz/T. Orostar mined out at 0.206 oz/T and Scadding at0.156 oz/TAu . The combined exploration and development database contained 1394 fire assays, more than enough for statistical confidence in a normal distribution. Therefore this study was initiated to determine, if possible, why the mill head grades were lower than the averages and to experiment with several methods to determine whether a reliable statistical mill head grade estimation method would emerge. Despite the identical reserve grades, distinct differences in the grade distribution histograms are present. By studying the arithmetic and log-normal grade distribution s, with some attention to South African practices, this paper reports on those differences which may account for the considerable divergence in the mill head grades. Furthermore, this study casts considerable doubt on the industry standard method of cut weighted averages.The global mill head grades of the two deposits have been derived from the arithmetic average grades by graphic means. This precise method of mill head grade prediction, if applied to complex orebodies, could permit selective grade control and result in direct cost savings by allowing the operator to detect false value stopes, benches or levels and emphasize reliable regions of not only gold mines, but also uranium or base metal deposits."

Jan 1, 1992

By Peter Dunn

London Mining Plc. is developing an iron ore project in Sierra Leone. The Marampa mine is a brownfield development effort, having been operated by others since the 1930?s until low iron ore prices forced closure. Peak production of the prior operations was approximately 2.5 Mt/a in the 1960?s. Following civil war In Sierra Leone, London Mining obtained the mining license in 2006 and commenced activity to redevelop the Marampa mining and processing operations. There are two ore deposits of interest for development as well as a resource comprised of tailings from previous operations. Phase 1 will be the mining of the tailings resource with a 1.8 Mt/a plant producing 66 per cent Fe sinter feed, expandable to 3.6 Mtpa. The first phase is currently under construction with start-up expected in the third quarter of 2011. Phase 2 will include development of the two ore deposits. These deposits are weathered secondary ore and the main primary ore resource. Phase 2 is currently under prefeasibility study and targets a final 16 Mt/a concentrate production in 2016. Outotec partnered with London Mining on testing efforts to develop the magnetic separation flowsheet using SLon VPHGMS machines to process the Marampa material. This paper explains the flowsheet development process for the weathered and primary ores commencing with sample characterization and detailed parametric investigations to evaluate SLon performance. The final flowsheet configuration is explained, including expected circuit recoveries and concentrate quality, clearly demonstrating the performance of the SLon VPHGMS circuit in iron ore tailings treatment applications.

May 1, 2011

By J. Sammut, T. G. Joseph, R. Andreev, M. Curley

"Decisions regarding mining method and subsequent choice of excavator must take into account the quantitative factors of productivity, availability, and capital, operating, and maintenance costs. Dig performance was compared between a hydraulic excavator (HE) and electric rope shovel (RS) of similar size class (i.e., use the same amount of energy to excavate a unit quantity of the same material from a mining face), focusing on the quantitative factors above. Machine performance, normalized to bucket capacity, was assessed as a function of hours of service (60,000 hours per machine). Results showed higher production rates for the HE of similar capacity and age. In general, the RS exhibited lower service cost per volume capacity, though it had higher capital cost. The RS became more cost effective than the HE of similar capacity within approximately 30,000 hours of service. ¦ KEYWORDS Cost, Electric rope shovel (RS), Excavation, Hydraulic excavator (HE), Surface mining RÉSUMÉ Les décisions concernant la méthode minière à adopter et le choix ultérieur d’un engin d’ex¬cavation doivent tenir compte des facteurs quantitatifs de la productivité, de la disponibilité ainsi que des coûts d’investissement, d’exploitation et d’entretien. Cette étude compare les performances en termes d’excavation d’une excavatrice hydraulique et d’une pelle électrique à câbles de même taille (qui utili¬sent par exemple la même quantité d’énergie pour creuser une quantité unitaire du même matériau dans un front de taille), en se concentrant sur les facteurs quantitatifs susmentionnés. La performance de la machine, normalisée à la contenance du godet de volume unitaire, est évaluée en fonction des heures de service (60 000 heures d’activité par machine). Les résultats montrent des taux de production plus élevés pour l’excavatrice hydraulique d’une capacité et d’une ancienneté similaires. De manière générale, la pelle électrique à câbles affiche un coût d’entretien par capacité volumique inférieur, mais son coût d’in¬vestissement est plus élevé. La pelle électrique à câbles devient plus rentable que l’excavatrice hydrau¬lique d’une même capacité au bout d’environ 30 000 heures de fonctionnement. ¦ MOTS CLÉS coût, excavation, excavatrice hydraulique, exploitation à ciel ouvert, pelle électrique à cablesINTRODUCTION The most common excavating tools in surface mining operations are the hydraulic excavator (HE) and electric rope shovel (RS). In general, electric RSs are more reliable and cheaper to maintain (P&H Mining Equipment, 2007), but where complicated geological conditions exist, HEs are preferred because they are generally considered to be more mobile."

Jan 1, 2019

By D. Hatfield

"Flotation plants typically aim to maximise recovery at or above a target grade. As the ore from the mine varies, operators increase or decrease the mass pull in different flotation banks by adjusting air and level set points in order to achieve target concentrate grade. A methodology has been developed to maximise overall recovery at target grade by determining the optimal mass pull for each bank. However, the approach of targeting equal grade for each ore type in the deposit leads to sub-optimal overall recovery. This is because some ore types sacrifice a large amount of recovery to reach target grade while others easily achieve target grade and can be processed at higher than target grade for little or no loss in recovery. Processing different ore types at different grades and blending the concentrates therefore gives a higher overall recovery.This paper presents a case study where an 80 year production forecast was made for a large Chilean copper concentrator in feasibility stage. A circuit model was created using SGS’s Integrated Geometallurgical Simulator (IGS) for the different ore types to be processed. The model was calibrated from standard rougher flotation tests (MFT), cleaner tests and from the results of plant surveys of similar operations. The pull rates for each bank in the circuit were determined to achieve an optimal graderecovery curve for each ore type. These curves were combined at different concentrate grades for each ore type to obtain the mathematically optimal overall recovery at target grade. The paper shows a methodology for obtaining an optimal combination of operating conditions for each ore type to maximise overall recovery at a set combined concentrate grade."

Jan 1, 2013

By Gregg S. Hill, Bert J. Huls

"This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed us to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flow sheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit. Details of the technology behind each unit operation will be presented in later publications.INTRODUCTIONSince 1996 BHPBilliton and MEL (Minera Escondida Ltda.) have developed a process to recover copper from coarse particles in the rougher tailings. Copper recovery from fresh tailings is not new. Several operations in Chile, such as Chuquicamata, El Teniente (AMEC, 2003), Mantos Blancos and others have operated various forms of tailings circuits. Both Chuquicamata and El Teniente practice cascade flotation scalping off froth containing fine copper particles after allowing sufficient retention time, air inducement and, sometimes, additional reagent addition. Chuquicamata tailings are not segregated but floated in sequential cascade and conventional large cell arrangements. At the Valle Central operation of El Teniente a coarse fraction of mill tailings is ground and floated, with the rejects recombined with fine tailings and subjected to cascade flotation through a sequence of concrete launders as the tailings flow towards their final deposition area. Mantos Blancos cyclone the rougher tailings and blend the underflow with scavenger concentrate from elsewhere in the principal circuit prior to flotation in Wemco Cells. Kemess in BC, Canada operates a 160 m3 Outokumpu cell to reduce the tailings sulfur content (Rasmussen, et.al, 2004)."

Jan 1, 2005

By Gregory A. Johnson

Operations and Maintenance departments have long had an adversarial relationship. The widespread evolution and adoption of modern management techniques such as Reliability Centered Maintenance (RCM) and Lean Production however has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance, and are now adopting Lean throughout the organization. Modern management initiatives like these explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in the realms of people and methodology. One area that has lagged behind in supporting these developments however is information systems. Enterprise Asset Management (EAM) systems in maintenance and newer Manufacturing Execution Systems (MES) in operations have not been truly integrated in the way needed. Complicated plants, different software architectures, continually changing conditions and many variables have lead to systems problems which have contributed to the maintenance/operations divide. Master data synchronization (the ?plant tree?) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology including web services and service orientated architectures. New technologies are coming on-stream to enable the final ?bridging of the gap?.

Feb 1, 2008

By C. S. Maggs, L. Shwydiuk, H. W. Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomical. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

Jan 1, 2003

By Michel Aubertin

Les digues de retenue de résidus miniers devraient être conçues de façon à supporter les charges les plus défavorables qui puissent être anticipées. Les nombreux incidents survenus au cours des dernières années à travers le monde montrent toutefois que la stabilité de ces ouvrages reste encore problématique. Les cas de rupture les plus courants sont reliés aux glissements le long des pentes, à la liquéfaction des rejets, au débordement des bassins, ainsi qu?à l'érosion régressive et de surface. Après avoir rappelé la nature et l?importance des certains incidents récents, l?origine de ces problèmes est brièvement présentée. On aborde ensuite le lien entre les critères à adopter pour la conception des ouvrages et les risques associés à leur rupture. De nouvelles avenues pour aider à contrôler certains problèmes sont enfin discutées, en mettant l?emphase sur la codisposition des roches stériles dans le parc à résidus miniers.

Nov 1, 2002

By David R. Skuse, Jacek A. Kostuch, Steven M. Fortier

"Particulate ground calcium carbonate (GCC) is used as a filler and coating pigment in a wide range of applications including papers, paints, plastics and films. In this paper we will overview the requirements for GCC used in both filling and coating applications in the paper industry and highlight the processes used in the production of these materials.INTRODUCTIONCalcium carbonate is both abundant and very widely distributed occurring most commonly as limestone, marble and chalk (Harben 2002). Given, the high purity, whiteness and relative inertness of these materials it is not surprising that they are heavily utilised in a range of industrial applications. Worldwide ground calcium carbonate (GCC) capacity is estimated at 50.5 million tonnes per year (Roskill, 2002). This usage is divided between relatively coarse materials that are used in applications such as landscaping, cultured marble and carpet backing and finer grades that find application in plastics, rubbers, inks, paints and paper. Given the usage of calcium carbonate products across a very wide range of consumer products, the outlook for GCC is very promising with growth expected in many markets. Growth is anticipated across many applications in the emerging nations and more specifically in paper applications on a global basis.Over the last several decades the GCC processing industry has evolved to be well adapted to both the cost effective production and delivery of standard products and the production of high performance speciality products. Many of the standard unit operations found in the metaliferous raw material processing industry are also used, albeit in some cases in modified form, in the processing of GCC. Coarse products (diameter > 3 - 10 µm) are typically produced by dry processing routes. Whereas, the finer products are typically produced by a combination of wet and dry processing."

Jan 1, 2004

By S. Caron, P. Radziszewski

Industrial practice in mineral processing shows that an important problem in understanding and monitoring in-mill parameters is due to the lack of fundamental knowledge and appropriate sensors. However, over the last decade, Discrete Element Method (DEM) modelling has shown an interesting potential in describing the fundamentals of grinding mill behaviour, in improving the understanding of internal grinding mill dynamics, and in developing solutions to industrial practice. With the objective of bringing this modelling technology into the concentrator control room to assist operators, this paper aims to describe the main elements needed to apply this emerging and developing technology to on-line mill performance monitoring.

Jan 1, 2004

By Descarreaux. Jean

"The Abitibi volcanic belt was sampled along a cross section extending from Matagami to a point east of Rouyn. A few samples were also collected in Louvicourt township, Quebec. The major elements were determined for 344 samples, and rock names were defined using normative minerals. The analytical data were studied by means of variation diagrams. The Abitibi volcanic belt is characterized by rocks belonging to both the tholeiitic and calc-alkaline magmatic series, but they show some differences as compared to some typical reference series, particularly those from Japan. Basalt is the predominant rock type and accounts for 44 per cent of the sampled outcrops. The volcanic rocks are relatively poor in K2O and TiO2. Regionally, the volcanogenic copper-zinc mineralization is associated with the calc-alkaline volcanic sequences. Locally, within such sequences, some types of abnormal deviations from the averages are recognized only in association with the copper-zinc mineralization. The anomalies are ascribed to hydrothermal alteration consisting of the introduction of MgO and removal of N a20; enrichment in K20 is also observed where zinc mineralization predominates. Examples of such anomalous zones show that, in places, this alteration phenomenon can be quite extensive. Petrochemical characteristics can be used as geochemical ore guides in exploration programs."

Jan 1, 1973

By C. O. Aksoy

There is a long history of coal production in Turkey with electric energy generated from power plants since the 1950s. However, the cost of power generation is high. Therefore, it has become necessary to find a means of decreasing production costs to become more competitive in a global market. This paper attempts to economically minimize the overall operating costs of a dragline-shovel-truck system applied at an open pit mine that has fed the Yatagan power plant since 1979, lowering the lignite production cost, and indirectly, the overall electricity generation unit cost. Systems currently in place, as a result of former optimization studies, are time-consuming and expensive to re-implement to comply with today’s very different geometric and economic conditions affecting mining operations. In such cases, rather than re-optimization, it is more viable to identify the parameters that affect the minimum unit cost, via a cost minimization study, allowing present mine equipment to be utilized more efficiently. Unit cost minimization analyses are subject to the capacity of the pool of mining equipment available, combined with the mining block geometry from pre-stripping onwards. In this overall unit cost minimization study, P&H shovels and CAT 777 trucks with capacities of 15 yd3 and 77 tons, respectively, were used in truck-shovel pre-stripping operations. A 65 yd3 Marion 8050 dragline was used to expose the overburden immediately over the coal seam. Pre-stripping bench heights varied from 8 m to 20 m and dragline bench heights from 20 m and 25 m were evaluated to minimize the unit cost of field operations. Total overburden extended to a depth of 60 m (35 m to 40 m for pre-stripping). Minimization analyses performed on the pre-stripping truck-shovel operation, prior to dragline operations, determined that the shovel bench height should be 15 m requiring a dragline bench height of 25 m.

Jan 1, 2005

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011

By Anand Raman, Steve Dixon

"Industry practice for defining acid consumption is based on column tests. Freeport-McMoRan (FCX) has adopted a practice of leach operation using a defined pH or gpl acid in the raffinate based on the column test program. The acid consumption can be easily calculated using the leach operating parameters of SX-EW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate. The column leach test results and a column to heap efficiency factor are used to define the copper extraction. The maximum acid consumption will occur when zero acid is contained in the raffinate. The term Net Extracted Value (NEV) is to define the maximum extracted value relative to acid consumed.This paper presents the operating logic and method used to calculate acid consumption based on column tests and operating parameters.INTRODUCTIONIndustry practice for defining acid consumption is based on column tests. This may result in lower economic value if the tests are not designed to account for operating variables. A test program is described to assist in defining lift height and the influence of gangue on solution chemistry. A simple spreadsheet is presented that will use the leach operating parameters of SXEW efficiency, lift height, bulk density, irrigation rate, primary leach cycle time, acid cure dose and acid concentration in the raffinate to calculate the acid consumption for a proposed operation.A review of current leach operations solution chemistry will help to define acid consumption. This is recommended for all current leach operations.DISCUSSIONThe current practice at Freeport-McMoRan (FCX) is the use of column test results to define operating parameters. The monitoring of operational solution chemistry and copper production addresses any changes needed in operational parameters. This practice maximizes the value extracted from each tonne of ore leached."

Jan 1, 2008

By R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. This paper presents the findings of on-going testing of various sizes and shapes of grinding media. Plant observations combined with estimated breakage rates demonstrate the importance of appropriate selection of media sizes on the milling operation.IntroductionBrunswick Mining and Smelting is located near Bathurst, New Brunswick, and operates one of the world's largest lead and zinc mines. The ore mineralogy and processing flowsheet have been described elsewhere (Petruk and Schnarr, 1981; Shannon et 01., 1993). Despite the 25 years' milling experience, there has been considerable disagreement as to the required grind size (Grant et 01., 1991). Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37 um) and averaged slightly above 71% in 1992. Results from mineralogical analysis (Petruk and Schnarr, 1981), laboratory and pilot plant experiments, as well as plant sampling (Grant et al., 1991; Hendriks and Ounpuu, 1985; Shannon et al., 1993) indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15 urn to 25 um range.This paper shows the results obtained so far from the evaluation of the effect of grinding media size and shape on grinding mill efficiency. The problem of finding optimum grinding media size, shape and composition has been recogrtized since the early 19405. The main criterion for the selection of media size is the size of the material to be ground (Bond, 1958). Although several relationships have been proposed to assist in the selection of grinding media size, none of them are entirely satisfactory (Wills, 1988). Other approaches using the breakage rates and process simulators were developed to help in the selection of grinding media size (Austin et al., 1976; Lo and Herbst, 1986; Concha et 01., 1992; Samskog et al., 1990; Martinovic et al., 1990). Although considerable effort was put into the analysis of grinding media size, very little information is available on the effect of grinding media shape (Norman and Decker, 1985, p. 3C-4). Norris (1952), Kelsall et al. (1973) and Herbst and Lo (1989) have shown that balls are more efficient than other shapes of grinding media including truncated cones and cubes."

Jan 1, 1994