Search Documents

By G. H. Gale, M. A. F. Fedikow, L. B. Dabek

Rare earth element (REE) data are reported for ores, sul?de-bearing rocks and host rocks from massive sul?de deposits and barren sul?de facies iron formations in Proterozoic volcanic rocks of the Flin Flon-Snow Lake area, Manitoba. Some of the rare earth elements (e.g., Eu), are selectively leached in zones of intense alteration and redeposited together with the sul?des and silicatesin the uppermost parts of the alteration zones and at the rock-water interface. Chondrite normalized REE pro?les of layered sul?de ores and exhalites proximal to the deposits typically have positive europium anomalies and are enriched in light REE. In contrast, barren sul?de facies iron formations exhibit negative or ‘normal’ Eu pro?les. REE data are useful to explorationists in determining the presence of ‘off-hole’ metal-bearing sul?de zones, in distinguishing metal-poor sul?dic layers related to ‘economic’ hydrothermal activity from barren sul?de facies iron formation and in some instances as a means of establishing ‘ore-equivalent’ strata.

Jan 1, 1997

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"Abstract - The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the La Joya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein (BPV) type, with a significant amount of the gold reserves contained in the oxide cap. Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the LaJoya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein(BPV) type, with a signi?cant amount of the gold reserves contained in the oxide cap.Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997

By Peter Cunningham

Teck Facts and Figures ? Employ more than 14,000 around the world, includes: ? Over 8,600 in Canada (close to 7,800 in British Columbia) ? Close to 2,000 in Chile ? Over 2,700 in Peru ? Approximately 600 in U.S. ? Hundreds more in exploration around the world ? Total capital expenditures ? $1.8 billion for 2012

Aug 1, 2013

By M. F. Goudge

ROCK wool, one of the most recent additions to the list of Canadian-made, insulating materials, is a soft, light, fibrous material consisting of interlaced, flexible, glassy fibres so exceedingly fine that, individually, they are almost invisible to the naked eye and will float in air. In the process of manufacture, a suitable rock, generally a self-fluxing argillaceous dolomite consisting of nearly equal proportions of acidic and basic constituents, is melted to a completely fluid state and then converted into fibres either by a blast of steam or air, or by a mechanical device. The increase within the past five years in the number of plants in the United States making rock wool and slag wool has been remarkable, especially in view of the depressed conditions prevailing 'with most industries during this period. In 1930, there were only 8 plants reporting production of .these materials, whereas at the present time there are 44 plants in the United States listed as making these products, and there are 3 plants in Canada. In 1929, the total sales of rock-wool products in the United States amounted to-$2,377,324. In 1934, according to the National Rock and Slag Wool Association, 26 member companies reported sales of $3,695,405, and in 1935 the sale's of 30 member companies had a value of $5,571,469. The establishment of the rock-wool industry in Canada followed the publication in 1931 of a report (1) by the Mines Branch, Department of Mines, Ottawa, in which was set forth the results of field work and laboratory studies which indicated that large deposits of rock in the Niagara peninsula, hitherto regarded as valueless, were suitable for the making of rock wool. This report was supplemented in 1934 by another report (2), giving the results of further laboratory and commercial-scale tests on the rock from these particular deposits, which proved conclusively that rock wool of good quality could be made from the rock in question.

Jan 1, 1936

By Bruno Lafrance

Abstract - Quartz veins at the Mufferaw gold prospect and Komis gold deposit, northern Saskatchewan, are examples of oblique-extension veins that crystallized in shear and tensile fractures, which propagated and then opened oblique to their walls during a single continuous deformation event. The Mufferaw gold prospect consists of an interlinked mesh of conjugate shear fractures, tensile fractures, and veins. Oblique-extension veins crystallized in conjugate shear fractures, which opened during dilation of intersecting tensile fractures under the same far-field stress system. At the Komis gold mine, tensile and dextral shear fractures cut across granodiorite dikes. The tensile fractures formed perpendicular to the dike margins during stress transfer from the less-competent country rocks to the more-competent dikes. During extension of the dikes oblique to the bulk extension direction in the country rocks, the tensile fractures were reactivated as sinistral shear fractures. The reactivated tensile fractures and dextral shear fractures opened oblique to their walls, parallel to the bulk extension direction, and were sealed by the deposition of oblique-extension veins during the same deformation event.

Jan 1, 2004

By F. McCarthy, R. McDonald, G. Woodbridge, G. Brock, D. Robinson

"The Direct Nickel process is a hydrometallurgical technology being developed to treat nickel laterite ores by leaching at atmospheric pressure. The leaching process uses nitric acid in a relatively large excess, is thus non-selective, and much of the soluble iron goes into solution. The first stage of solution purification is iron hydrolysis and the Direct Nickel process utilises the colligative properties of the pregnant leach solution (PLS) to enable the removal nitric acid of varying concentrations via distillation. Once sufficient acid has been removed, the boiling point of the solution is increased allowing high temperatures (up to ~170°C) to be achieved under atmospheric pressure. The higher temperatures initiate the precipitation of the iron primarily as hematite and allow the removal of the acid generated by the hydrolysis reaction. The rejection of the iron is near complete with solution tenors typically falling from 65 g/L Fe, or more, to less than 50 mg/L Fe. The separation of clean nitric acid from the PLS at this stage allows for relatively simple acid recycling. A hematite product with iron content above 60% could also provide an extra revenue stream.INTRODUCTION The Direct Nickel (DNi) Process is a novel hydrometallurgical processing route designed to treat all types of nickel laterite ores in a single flow sheet using nitric acid under atmospheric conditions. A simplified flow sheet is shown in Figure 1.Between 2007 and 2012 the process was developed and refined at Direct Nickel’s laboratory within the CSIRO Minerals’ facilities in Perth, Australia, and in 2013 a series of pilot plant trials were run under continuous operating conditions. The process is designed to treat both limonite and saprolite in the same flow sheet, and after comminution, the blended ore is mixed with nitric acid and leached just below boiling point in agitated atmospheric leach tanks. The acid is added in excess, so typically for a blend of limonite and saprolite the acid addition can be in the order of 1.8-2.0 t acid/t dry ore. After a residence time of between 4-6 hours the majority of the soluble metals have leached into solution and the insoluble leach residue is separated from the pregnant leach solution (PLS) via counter-current decantation."

Jan 1, 2016

By J. P. Mogan, E. D. Dainty, K. Katsuyama

"The Volvo BM 861 U articulated truck is one of the few underground diesel units manufactured by an organization which shares the same corporate roof as the engine manufacturer. As a consequence, the unit has provided an opportunity for the characteristics of the entire system- turbocharged aftercooled engine, transmission and exhaust scrubber- to interact to minimize emission levels. The performance of the components of the system, as evaluated by full-scale dynamometer testing, is summarized. The over-all effect of the various innovations was a 38% reduction in the recommended ventilation level over that of the bare engine.IntroductionThe Mining Research Laboratories of Energy, Mines and Resources Canada is required, as part o f the certification service of the Canadian Explosive Atmosphere s Laboratory, to test the exhaust emissions of diesel engines, and to recommend appropriate amounts of fresh ventilating air to minimize the risks to health of underground personnel working with, or in the vicinity of, such diesel engines. Volvo BM AB of Sweden made application for the certification of the BM 861 U truck during a period in which EMR personnel were engaged in a number of research projects concerned with improving the environment in dieselized mines. One such avenue of research was the venturi or high-energy scrubber; as the BM 861 U was equipped with this type of scrubber , EMR and Volvo BM agreed to cooperate in a considerably more extensive investigation than would be normal for a certification application. The outcome of some of this research is summarized in this paper."

Jan 1, 1981

By C. F. Chung, F. P. Agterberg

"Prediction of a variable sulphur content in Cape Breton seams is important for planning the production of a highgrade metallurgical coal. Two extrapolation methods (Kriging and a version of Universal Kriging) to predict sulphur content in blocks of coal before mining are presented and applied to the New Lingan Mine reserves in the Harbour seam. The uncertainty of the predicted values is expressed by using standard deviations. Some statistical results for the Phalen seam, which occurs about 400 ft below the Harbour seam, are presented for comparison. The two mathematical models consist of two sets of equations which have been used in computer algorithms. Some limitations of the present approach and possibilities for further statistical work are indicated."

Jan 1, 1973

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By A. Yaghini, Y. Pourrahimian

"Human factors (HFs) play an important role in the mining and mineral industry, affecting operational and maintenance efficiency and safety. Despite the introduction of new technologies and automation in this sector, it is well known that a significantly large proportion of total human errors occur during the operation and maintenance phase. A comprehensive literature review of HFs across several industries is provided. From this review, the impact of HFs on operation and maintenance is summarized, with a focus on what the mining industry is currently doing and what opportunities exist for additional improvements. Future research directions and themes are also identified.RÉSUMÉ Les facteurs humains (FH) jouent un rôle important dans l’industrie des mines et des minéraux, en ce qu’ils affectent l’efficacité et la sécurité de l’exploitation et de l’entretien. Malgré l’apparition de nouvelles technologies et de l’automatisation dans ce secteur, il est bien connu qu’une grande partie des erreurs humaines (EH) se produisent durant une phase d’exploitation et d’entretien. Cet article propose une analyse documentaire approfondie des FH dans plusieurs secteurs. L’impact des FH sur l’exploitation et l’entretien est résumé à partir de cette analyse, une attention particulière étant accordée à l’évolution de l’industrie minière et aux possibilités d’améliorer davantage ses activités. Sont également identifiés les futurs thèmes et voies de recherche.INTRODUCTIONDuring the past several decades, the mining industry has focused on improving equipment, machinery, and methods that have led to more advanced hardware and software, equipment with higher reliability and productivity, and other technological advancements. These actions have improved safety and productivity and have reduced casualties and maintenance workload. Although today’s mining equipment and machinery are technologically advanced and highly reliable, the risk of accidents is still relatively high and key performance indicators have not improved significantly compared to other industries (Sorensen, 2012). A prominent reason could be due to insignificant integration of human factors (HFs) as part of planning, operation, and maintenance activities. The current mining system is a people system, and inevitably HFs and human error (HE) figure prominently in all aspects of this industry. Even the most advanced technologies and innovations require operators and maintainers with significant knowledge and skill, which could increase the potential for HE."

Jan 1, 2018

By J. Mrozowski, R. Kurowski, A. Chmielarz, Z. Szolomicki

PbSO4 is a commonly encountered component of the materials used in lead recycling (e.g. battery paste) and in by-products of metallurgical processes (e.g. residues from zinc hydrometallurgy, dust from copper smelting). Smelting of battery paste results in SO2 emission and in generation of significant amounts of hazardous ‘white slag’. Those adverse phenomena can be eliminated by removal of sulphur from the paste. Lead-bearing by-product materials are of polymetallic character with usually low Pb content, which makes lead recovery technologically difficult and uneconomic. However it can be successfully achieved by extraction of lead sulphate from solid phase with triethylenetetramine (TETA) water solutions. That compound has capability for selective solvation of a whole lead sulphate molecule. Virtually pure lead carbonate can be precipitated by means of saturation of lead-loaded aqueous TETA solution with carbon dioxide, and complete regeneration of the extractant is achieved by fixing of sulphate ion into gypsum through operation of calcium hydroxide suspension. The paper presents results of the lab and pilot scale studies into process of battery paste desulphurisation and recovery of lead from the residue of zinc calcine leaching.

Jan 1, 2014

By H. R. Butler

"The Ontario Division of Inca Metals Company, a Unit of Inca Limited, operates eleven mines, four mills, three refineries, one smelter and one iron ore recovery plant. All but one mine, mill and refinery are located within a fifty kilometer radius of Sudbury, Ontario. A mine-mill complex is located some 100 kilometers west of Thunder Bay on the shore of Lake Shebandowan and a nickel refinery at Port Colborne.During the past 10 years the use of recycled water in our milling operations has increased to more than 95% at each mill. This high degree of water reuse has reduced the (a) need for fresh water and (b) the contaminant level of the downstream aquatic environment. The aggregating of effluents in a common receptor provides a process water having a consistent quality thereby minimizing upsets in mill metallurgy while concurrently improving the operating economies and the downstream aquatic environment."

Jan 1, 1980

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By Hugh P. Godard, K. Winslow

"AbstractA number of panels of various aluminum alloys in different combinations and secured by steel and three types of aluminum rivets were exposed underground at two locations in a Northern Ontario gold mine for two years and then examined to determine the extent of corrosion. The results indicate Alcan 65S-T to possess considerable advantages over Alcan 178-T, which has been employed in the construction of light skips and cages with considerable success for almost twenty years. Information on the behaviour of these alloys when used with steel rivets and in mixed combinations with themselves was obtained.IntroductionBy the complete substitution of aluminum alloys for steel in the fabrication of mining skips and cages, their weight can be reduced as much as 50 per cent. Lesser savings are possible though its savings are possible through its plates, doors, reinforcing members, etc. Reduced weight leads to economy through increased hoisting efficiency.For a new installation, the basis of design is the rate of production, which thus fixes the live load to be hoisted per trip. A lighter skip permits the use of a lighter rope and a smaller hoist. In deep shafts with high-speed hoists operated in balance, the power required for accelerating is considerable. The hoist size is determined by the weight of skip, load, and rope plus the force required to accelerate or decelerate these three elements A light skip may result in a considerably lighter rope. This is important because, even though the skip can be completely balanced this is not true of the rope. Partial balancing is possible, but conical hoist drums or other devices for this purpose are costly; thus a smaller rope results in a smaller hoist, with consequent general reduction in cost of the whole installation. A reduction in power consumption is also obtained as a result of keeping to a minimum the amount of unbalanced load and the weight of all moving parts which must be accelerated."

Jan 1, 1950

"The success or failure of coal mining operations in Western Canada may hinge on the ability to extract thick coal under a variety of geological and mining circumstances and conditions. The paper presents, in who-where, what- how pattern, the current status of undergrounud mining of thick coal seams based on a review of foreign technical literature. The underground production of coal from what are considered to be thick seams is over 300 million tons per year. Methods of mining have evolved, through years of trials and tribulations, capable of meeting the requirements of a modern mine: high bulk outputs from a limited number of mining faces by concentrating in the horizontal (mechanization) and in the vertical (increased working lift)."

Jan 1, 1972

By Kretschmar. U. H.

Fieldwork in the Meguma of Nova Scotia and Archean equivalents shows that bedding-parallel quartz lode gold veins (LVs) commonly occur at the top of graded elastic sequences. We define a "gold cycle" (GC) by analogy with Bouma turbidites and show that most "shear zones" and "lamprophyres" correspond to the upper pelagic-pelitic (E) division. We describe GCs from Archean Chester Twp, ON; Elmhirst, ON; Bourlamaque, QC; "intrusions" and interpret them as crystal tuffs and tuff-breccias. Extensive early Archean pyroclastic volcanism is implied: the genesis of trondjhemite-tonalite-granodiorite (TTG) rocks must be re-examined. The geopetal nature and asymmetric alteration of LVs indicates genesis from sea-floor hydrothermal vents. Textures suggest that often quartz was deposited as a gel. Vent geometry (fracture, point source or diffuse seep), bottom topography and vent spacing is reflected in wade-thickness plots. GC facing directions survive metamorphism. The Bourlamaque batholith was a flat-lying sheet of quartz-feldspar-hornblende crystal tuff, and isoclinal folding has repeated one or more gold-bearing horizons. Syngenesis clarifies and simplifies LV formation with major implications for models. Exploration becomes more cost-effective. Basin analysis, whole rock geochemistry, ore lens geometry and vent spacing can be used.

Jan 1, 2011

By Jiuhua Xu, Yuling Xie, Fenglei Bie, Neng Jiang

"Abstract - The Xiaoqingling Mt. area is one of the most productive gold districts in China. The gold-bearing quartz veins are controlled by a series of east-west shear zones within the Archean Taihua Group, and related to the late Yanshanian (Cretaceous) granite. The major metallic minerals are native gold, electrum, pyrite, galena, chalcopyrite and sphalerite, with gangue minerals dominated by quartz, sericite, ankerite, and calcite. The host rocks are mainly amphibolite, plagioclase gneiss, and migmatites. Principal alteration is sericitization, silicification, pyritization, and carbonization.There are four generations of hydrothermal quartz in altered rocks of gold deposits. The earliest generation of quartz, (Q1), occurs in altered amphibolite gneiss and migmatite, and typically contains fluid inclusions with halite crystals (type A) and two phases, (L+V), of fluid inclusions (type B). The salinities of type A inclusions are 32 wt% to 52 wt%, with dissolution temperatures of halite crystals being from 155°C to 465°C. The second generation of quartz, (Q2), occurs as a fine-grained aggregate associated with sericite, and has small (less than 3 µm) type B inclusions. The third generation of quartz, (Q3), occurs in mylonitic, intensively altered rocks and specially beresite (a type of rock composed of quartz, sericite, and pyrite) near the veins, and contains large amounts of CO2-rich fluid inclusions (type C-fluid inclusions with liquid CO2 and type D-fluid inclusion with high density CO2). The CO2 contents of type C range from 72.6 to 87.4 mol% in gas phases, and 35.7 to 68.3 mol% in liquid phases, based on Laser Raman analysis. The homogenization temperatures of fluid inclusion type A and C are from 215°C to 380°C, and from 210°C to 325°C, respectively. The minimum trapping pressure of fluid inclusions is estimated as 80 MPa to 170 MPa for type A, and from 57 MPa to 190 MPa for type C, which approximate to those of fluid inclusions in vein quartz.The ?18O of quartz are from 10.4‰ to 11.0‰ for Q3 of altered rocks, and from 10.7‰ to 12.8‰ for stage I quartz. The calculated ?18O of fluid inclusions varies from -1.3‰ to 6.0‰. The ?D of fluid inclusions ranges from -67‰ to -59‰ and from -81‰ to -48 ‰, respectively. It is concluded that the water in the hydrothermal fluids both reacting with wallrocks and precipitating orebodies could have been mainly of magmatic and/or metamorphic nature. However, local meteoric water might have been important in late mineralization, because of a distinct oxygen-shift toward the meteoric water. The ?34S values for pyrite of the ores range from -7.1‰ to +7.1‰, with an average of +2.9‰. Those of other sulfides (chalcopyrite, galena, and sphalerite, range from -12.5‰ to 8.3‰. The ratios of lead isotopes for galena of the ores are: 17.06 to 17.31 (206Pb/204Pb), 15.43 to 15.74 (207Pb/204Pb) and 37.58 to 38.45 (208Pb/204Pb). In summary, ore-forming fluids in the Wenyu-Dongchuang gold deposits may have originated from a mantle and/or lower crust source, and ore materials were derived from the Precambrian basement, the Taihua Group."

Jan 1, 1998

This paper examines the latest advances in mine hoist motor and drives systems. The technology employed for large hoists has migrated from the traditional DC technology to AC motors with cyclo convertor drives, and more recently, advances in pulse width modulation (PWM) drives have resulted in these being applied to large hoist drives. When combined with PWM drive technology, the induction motor presents the ideal solution for hoist applications This paper examines the factors in choosing a suitable PWM drive and motor for a hoist installation. Factors under consideration include: ? hoist duty cycle, ? drive rating restrictions, ? choice of power semiconductor device,, ? low speed operation, ? maintenance ? reliability The cage induction motor and synchronous motor are compared and it is shown that the induction motor is the motor of choice for large hoists.

May 1, 2010