Search Documents

By Roméo Roussin

"The yearly production from the Asbestos Hill pit is 1,550,000 tons of asbestos ore, with a yield varying between 18 and 20 % . The orebody was exposed at the top of a hill, and initial production started without having to remove any overburden. The projected ratio of barren rock to ore, based on the present orebody, was 2 to 1. However, as it was necessary to push back the upper benches, this ratio has changed to 3 to 1. The final pit will be 2,300 feet long by 1,000 feet at the longest and widest points. The final depth will be 680 ft. A pit slope stability study was carried out and an average wall angle of 60-70 degrees must be maintained. Preshearing of final pit limits will produce good wall stability. Permanent access ramps will be 60 ft wide, with an 8 % maximum grade. Geological conditions and the low rock temperature are the major causes of the operation's drilling and blasting problems."

Jan 1, 1976

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

By F. S. Thurner

This paper, a description of the new ore-unloading and stockpiling facilities at the Sydney Works of DOSCO Steel Limited, deals with a new approach to arrive at the most economical solution to combine ore unloading facilities for common bulk carriers and for different types of self-unloading vessels. Also discussed is the design and installation of a 1-mile-long steel-cord belt conveyor sys-tem with a most modern type of mobile belt conveyor stacker, along with automatic and semi-automatic controls for the entire ship-unloading and stockpiling operations.

Jan 1, 1968

By J. C. Nicholson

The "V" system was first introduced by the West Virginia Coal & Coke Company at their No. 9 mine, Norton. Norton is a small mining village on the B. & 0. railway, about seven miles from the town of Elkins. This year, accompanied by G. D. MacDougall, I visited this mine to obtain first-hand information regarding this modem system and to determine its adaptability to conditions in Nova Scotia. The following is a brief account of my observations. The seam that is being worked is known as the Lower Kittaning, which, at this point, has an average thickness of 7 feet. This includes a band of hard clay varying in thickness from 8 to 14 inches, which occurs about 2 feet from the pavement, also 8 inches of inferior coal at the roof. The latter is not recovered, which leaves to be mined about 5 1/2 feet of clean coal. The roof is slate and shale for the first 30 feet, followed by 40 to 60 feet of sandstone; the total cover is from 80 to 250 feet thick. The seam lies very flat, with a dip of only 2 per cent., and, as the dip is toward the main entrance, it' is in favor of the load, also providing natural drainage for any water the mine makes. As the mine is not gassy, and there is no water to be pumped out, one can understand that mining conditions are practically ideal.

Jan 1, 1924

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By A. J. Paul Laprairie

"ADVANCE planning of mining methods, from the first development openings to stope layout and pillar recovery, has long been accepted as a normal method of operating a mine. Recently, mine managers have become increasingly aware that advance planning of cost and accounting controls can also be considered a normal method of operation. The use of such controls is wide-spread in manufacturing industries. In mining, the gold mines of South Africa have pioneered, with marked success, in this field and have been closely associated with most of the research and field work in accounting control. Canadian mine managers are also beginning to realize the advantages of using planned costs. The control procedures which subsequently have been introduced at various mines have come to be known by such names as ""Responsibility Costing"" or Budgetary Control"".Budgetary control, the term used in this paper, is based on the concept of decentralized authority with centralized control. ;The control is achieved by measuring results against yardsticks which are in the form of budgets or standards. Bud-gets are made for the future activities of each possible operation as planned by the department head, and attention is directed to variations from this plan. Furthermore, the control process charges to each operation only those costs which are incurred directly for that operation, and which can be controlled by the person in charge. Thus, budgetary control relates results to the officials responsible for those results. Expenditures are analyzed according to the organizational structure of the mine and the people who run it, and not according to production processes."

Jan 1, 1960

By E. A. Davies, Trevor T. Jones

"Aspects of materials, design and operation of suspension equipment is dealt with, hazard, fatigue and special metallurgical properties of certain steels to resist are described, as is the effect of temperature in service modifying the properties of some steels to resist stress concentration and propagation of cracks.The influence of steady impact and fatigue loading and its results are described. Control of manufacture including nondestructive testing is outlined and acceptance parameters and strength calculations are given. Quality requirements and control in manufacture are outlined. A short description of the overwind detaching hook, together with illustrations of the operation of detachment are presented.MaterialsWinding engine ratings of 8000 h .p. and large capacity shafts 2000 m in depth (4000 m depths have already been reached and it may be necessary to go to 6000 m) and up to ten conveyances are not uncommon today. Loads of 100 or even 200 tons hoisted at low speeds are possible within the near future. Some of these appliances are designed to protect lives and installations in hazardous conditions when, due to human or mechanical fault, a malfunction occurs in the system. In addition, such equipment includes suspension gear of various kinds designed to anchor and apply high mechanical tensions to numerous steel ropes installed in shafts necessary either for the safe passage of conveyances or for balancing purposes when heavy loads are in motion.No unique metallurgical problems are presented in underground mining operations, but they have two special characteristics that influence the metallurgical aspects of the de sign of suspension gear and other equipment concerned in the transport of men and materials. (1) Any uncontrolled release of energy caused by the unexpected failure of a component is more likely to injure personnel and cause costly damage to installations in the narrow confines of an underground mine shaft. (2) Some mechanical equipment in mines, tends to be overloaded in service and suffer plastic distortion."

Jan 1, 1987

By A. O. Dufresne

The mineral wealth of pre-Cambrian rocks in Canada has been the subject of much study by geologists and engineers (members of this Institute), particularly so in the past few years, following discoveries of mineral deposits in areas far a part. This interest is well worth sustaining knowing the numerous rich producing mines within the pre-Cambrian formations, and the vast area covered by its rocks throughout this country. The pre-Cambrian has yielded minerals, both metallic and non-metallic; of these a much diversified list could be made. In more than one district we can point to mining as being responsible for the opening up of new sections, attracting a population into regions which otherwise would have remained virgin land of little commercial value. In these pre-Cambrian formations are found the rich copper deposits of Michigan, producing without interruption since 1845, and from which seven billion pounds of copper has been won; while in Minnesota and the adjoining district, at the head of Lake Superior, are mined iron ores which have rendered possible the great steel manufacturing industry of United States, the base of the economic structure of that wealthy country. The pre-Cambrian has given Canada the nickel-copper mines of the Sudbury district, the silver deposits of Cobalt and the gold camps of Porcupine and Kirkland Lake. With all of these our members are familiar; and it suffices to mention them to bring to mind pictures of the wealth and 'the growing population, in a word the importance of mining in?those sections of the country.

Jan 1, 1926

By Frank E. Lathe

During the war the National Research Council at Ottawa sent out questionnaires to the managers of nearly all the industrial plants in Canada. Inquiry was made as to the research equipment possessed, the number of research workers employed and the nature of the research problems which still remained unsolved. Practically all the companies reported that they had no special facilities for research, had no re-search workers and did not require the assistance of the National Research Council-because they had no research problems. Perhaps we have here one of the chief reasons why certain of our manufacturers find themselves unable to meet foreign competition. For hundreds of years the Indian tribes of northern Chile worked, in a small way, the copper deposits at Chuquicamata. They had no research problems and made no striking success of their mining operations. Then came an American company with a research problem, which they proceeded to solve. To-day the stock of that company has a market value of about $140,000,000.

Jan 1, 1926

By F. M. Clement

British Columbia, unlike the Prairie Provinces, cannot lay claim to vast prairies. She can, however, claim many valleys, uplands and plateaus that are capable of marked agricultural development. It has been said that British Columbia is not an agricultural province. This may or may not be true, but at the present time agricultural production in this province stands second only to that of forestry. The industry has advanced from a total production of 8 millions in 1908 to a total production of 60 millions in 1924, a total increase of approximately 650 per cent in 16 years. In the last 10 years production has increased from 30 millions to 60 millions. No other industry can point to such a rapid development. In 1908 British Columbia imported 12 million dollars worth of foods compared to the 8 millions which were produced at home. In 1924 she imported 20 million dollars worth of foods compared to the 60 millions worth produced at home. In addition we exported foods to the value of approximately 10 million dollars. British Columbia is therefore self-sufficing in-so-far as values ar.e concerned except for approximately 10 millions of dollars. It is not to be expected that this province will ever grow all the coarse grains that she may require: these, along with certain meats, will always be a heavy item in the imports. We are concerned at the present time more with the value of the products than with the quantities produced: in other words, with quantities only in-so-far as ? quantities improve value.

Jan 1, 1925

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By K. Forsberg, A. Rasmuson, R. Rodriguez Varela, J. Martinez De La Cruz

"This study analyzes the separation of rare earth elements by means of a supported liquid membrane (SLM) with the final objective of recovering REE from an apatite concentrate (Alemrajabi, Forsberg, & Rasmuson, 2015; Mohammadi, Forsberg, Martinez de la Cruz, & Rasmuson, 2015). In this study, the feed phase consists of an aqueous phase containing REE, the membrane phase contains the organic solvent and carrier (D2EHPA and EHEHPA), and the stripping phase is a hydrochloric acid solution. An evaluation of mass fluxes, separation efficiency, and membrane performance is conducted. In order to analyze the suitability of liquid membranes in the extraction of REE, a deeper insight into the mechanisms causing instability is needed. In this study, surface tension is considered as the key factor of Marangoni instabilities and spontaneous emulsification.INTRODUCTIONThe demand of REE and their compounds has increased considerably due to their special physicochemical features that make them crucial elements for numerous high-tech applications, including wind turbines, hybrid cars, mobile phones, and defense technologies. They are also extensively utilized in traditional industries such as nuclear energy, petroleum, metallurgy, agriculture, and textiles (Xie, Zhang, Dreisinger, & Dyole, 2014; Zhang, Wu, Bian, & Zeng, 2014).Solvent extraction is widely used for the separation of REE (Xie et al., 2014; Zhao, Huo, Pan, Li, & Liu, 2014). Di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHEHPA) are two of the most effective extractants for the separation of rare earth elements among organophosphorus extractants (Gupta & Krishnamurthy, 2005). However, the difficulty in stripping loaded D2EHPA extractant, especially for heavy REE, has limited its utilization. Yttrium can be stripped at lower acidities in EHEHPA systems compared to D2EHPA systems (Gupta et al., 2005), but the extraction efficiency is lower. Conventional solvent extraction by mixer-settlers is restricted by its large solvent inventory and loading limits, and suffers from phase disengagement, emulsification, loss of solvent, and flooding problems (Swain, Jeong, Lee, & Lee, 2007). In this context, supported liquid membranes (SLMs) present a potential alternative due to their advantages, being low solvent inventory, process simplicity, low energy and operational costs, great enrichment ratio, and combination of extraction and stripping into one single step. A SLM is a system in which two aqueous phases are separated by an organic liquid membrane suspended in the pores of a porous support by capillary forces. One of the aqueous phases is the feed solution with the solute and the other is the stripping or receiving solution. The solute diffuses through the liquid membrane and then is extracted into the stripping solution (Kislik, 2010)."

Jan 1, 2016

By M. Alvarez-Silva, A. Uribe-Salas, J. A. Finch, M. Mimezami

The point of zero charge (PZC) of electrokinetically anisotropic minerals (chlorite and serpentine) was determined using the Mular-Roberts (M-R) titration technique, and compared to isoelectric point (IEP) obtained from electrophoretic mobility measurements. To validate the M-R technique, the point of zero charge and isoelectric point of two isotropic minerals (alumina and silica) were shown to be comparable. For serpentine and chlorite, respectively the PZC was found at pH 4.3 and 4.6, while the IEP occurred at pH 3.2 and <3. Settling tests showed that the maximum settling rate, which corresponds to aggregated particles, for chlorite was around pH 3, i.e., close to the IEP; lizardite did not show a conclusive maximum.

Jan 1, 2009

By P. D. Hanson, H. Colijin

"New procedures and techniques are now available for the design of bulk storage bins. These new methods have essentially eliminated guesswork in the gravity flow of bulk solids, and have provided a sound basis for the quantitative analysis of alternate designs of hoppers and bins. This paper will discuss the practical application of the Solids Flow Theory (Jenike & Johanson) and illustrate the required design procedure with a few examples of actual bin operations."

Jan 1, 1970

By Eduardo A. Pérez, Alejandro R. Alonso, Rosa María Luna-Sánchez, Gretchen T. Lapidus

Rare earth elements have been widely used in various sectors, from the aerospace and steel industries, to electronic applications, particularly in displays and batteries for portable devices. The high demand for newer and better equipment, such as cell phones, tablets and lap tops, has increased the consumption of the rare earth elements and at the same time the need for its recovery from electronic wastes. For that reason, the recycling of batteries is important, principally the Ni-HM batteries, due to their elevated content of rare earths elements, in addition to the high concentrations of cobalt and nickel. The current processes are based on dissolution in strong acid solutions (sulfuric acid concentrations from 2 to 4 mol/L), and temperatures from 30 to 90°C. In the present work, electrodes from spent Ni-HM batteries were leached using 1 mol/L H2SO4, in the presence of ozone as the oxidant, where recoveries of 96% for La, Ce and Nd were obtained at room temperature. The separation of Ni and Co from the leach solutions was performed using an electrochemical reactor, after which rare earth elements were precipitated, obtaining a mixture of its hydroxides with impurities below 1%, according to EDS analysis.

Jan 1, 2014

By G. Marchand, R. H. Hay, E. C. Pearson

"AbstractA polishing .technique is described together with two anodic etching methods for aluminum and its alloys. Some of the optical and structural characteristics of the film formed by •these etching methods are discussed and it is shown to what degree these properties of the film are related to the crystallographic orientation of the metallic substrate. Applications to the study of recrystallization and twinning phenomena and to the study of plastic deformation, banding, and texture estimation are discussed. Micrographs are shown .to illustrate the manner in which the technique is particularly well suited to the study of such phenomena.IntroductionThe physical metallurgist is constantly faced with the problem of polishing and etching of metallic sections. Mechanical polishing is tedious, time consuming, and not applicable whenever a surface entirely free from plastic deformation is required. Etchants are generally required to reveal the grain structure in order to determine its size, shape, and regularity, or to bring up constituents. In the case of aluminum, the .most common etchant to reveal grains is a mixture of three acids: HC1, HN03, and HF. This etchant is fairly satisfactory on certain alloys and for certain metallurgical conditions but in general fails to give a good definition of the grain on castings, on highly alloyed products, and whenever the grain is smaller than 100 microns in diameter. Besides size and shape, a grain, or crystal, has an orientation and may be endowed with several types of imperfections."

Jan 1, 1952

By J. Jacob, A. G. Guézennec, F. Savreux, S. Nanaa, M. Delclaud, P. d’Hugues

Mining wastes can contain base and precious metals, but also metalloids and rare earth elements that are nowadays considered as highly critical for the industrial development of the European Union. The development of alternative routes to conventional processing is still required in order to decrease the cost associated with the treatment of these resources, which are more complex in composition and with lower grades. An ecologically acceptable and yet economic alternative for processing of low-grade sulphidic primary ores as well as mining wastes is the extraction of metals using bioleaching processes. The purpose of this study was to test the potential of bioleaching procedures for the extraction of residual metals contained in sulphide-rich tailing wastes coming from a European copper mine. These wastes are mainly composed of pyrite (60%) and contain cobalt (0.06 %) and gold (0.95 g/t). Bioleaching experiments were performed in 2 L stirred reactors in batch mode and in pilot tanks (110L) in continuous mode, using the "BRGM-KCC" bacterial consortia. High metal extractions were obtained (cobalt dissolution > 90%), which confirm that bioleaching is an effective process for this tailings material. Experimental results were used to design a global treatment process scheme and to perform a preliminary economic evaluation, showing good profitability of a hypothetical industrial project.

Jan 1, 2014

By Martin Lebeuf

The phenomena occurring in the cathode and at the cathode surface of aluminum electrolysis cells are very important in regards to cathode voltage drop and cathode wear. In the current study, laboratory-scale aluminum electrolysis cell cathodes were analyzed by X-ray microtomography. This technique allows an excellent visualization of the distribution of different substances, if their respective X-ray attenuation coefficients are different enough. In the current case, the important difference in the mean atomic number between cryolitic bath and graphitic carbon results in good contrasts. The volumetric bath penetration profile, porosity and impurities distribution in the cathode were thus obtained. Furthermore, metallic impurities and bath heterogeneities were observed at the cathode surface. Observations were also made with Scanning Electron Microscopy - Energy Dispersive Spectroscopy (SEM-EDS).

Jan 1, 2011

By S. K. Dimitrov

?Ellatzite Med? is one of the biggest mining companies in Bulgaria, processing about 12,000,000 t of ore per year. Waste materials left after extraction of copper concentrate are deposited in tailings dam ?Benkovski 2?. The hydraulic structure is built according to the downstream method, through hydrocyclonization where the downstream batter and the body of the wall are formed by the separated coarse sand particles of the separated tailings. In connection with the prolonged concession of Ellatzite Med and the enlarged capacity of Benkovski 2, the tailings dam has expanded on to the surrounding terrain. To guarantee a normal hydrocyclonization and build up of a tailings wall during waste deposition from the ore mill, the technological scheme of the hydraulic transport system of Benkovski 2 has been changed.

Aug 1, 2013

By D. Furrer, M. Dallaire

The arrival of Image analysis in the last 20 years has changed the world of quantitative metallography. Many standard measurement techniques which were previously manual can now be done with fully automated systems. This reduces subjectivity and operator fatigue and therefore enhances the quality of the statistical results. In many laboratories, Titanium Alloy microstructures continue to be evaluated by traditional methods, where quality of results is subject to operator fatigue and level of experience. Advances in Camera technology have tremendously improved image acquisition. One can often see clearly at 500x what can not be observed at 1000x, allowing for a larger area to be analyzed, without the inconveniences associated with very high magnification objectives. Powerful and versatile Image analysis software combined with a high precision motorized stage gives access to a multitude of applications, which were extremely challenging or impossible until now. Image Analysis tools such as Multilayer Grab, which reconstructs an uneven image into one plane of focus (ex. Observation at high magnification of texture resulting from etching) and Mosaic which builds an image from a number of fields of view (ex. Reconstruction of very large grains at low magnifications) expand even further the power and flexibility of IA systems. This presentation will describe how automated methods are applied to the point count method and grain size measurement. We will show how cameras and software work together to permit quantitative measurements of primary alpha and prior beta microstructures, as well as lamellar alpha plate thickness in titanium alloys.Automated and semi automated quantitative measurements of various Titanium microstrures have been assessed, using the Clemex Vision PE. Examples of the methods and steps used are presented.

Jan 1, 2006