Search Documents

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By Subagyo, Geoffrey Brooks, Ken Coley

The generation of droplets and their subsequent reaction in the emulsion is critical to the overall kinetics of oxygen steelmaking. High temperature experiments have been performed at McMaster University to study this behavior. The results from this work and other previous studies has formed the basis of a number of physical and chemical models that attempt to describe the critical aspects of droplet behavior in Oxygen Steelmaking. These models include semi-empirical models for predicting droplet generation rate, droplet size distribution and droplet residence time as a function of blowing parameters.

Jan 1, 2004

By Barry J. Morash

The over-all slope angle of between 55 and 60 degrees at the Adams Mine necessitates control blasting on the final pit walls. The control blasting techniques used are pre-shearing and buffer blasting. Pre-shearing with 2'I2-inch holes on 5-foot centers is used in areas where jointing and rock type are not conducive to smooth stable walls. Buffer blasting with 12'/4-inch holes is used in areas where the rock is competent. Control blasting adds to the operating costs, but can result in substantial savings in increased slope angle and reduced stripping.

Jan 1, 1978

By Navid Bahrani

The grain-based model (GBM) has resolved the difficulty of matching both the directtension (sc) and unconfined-compressive (st strengths of typical brittle rock by providing a synthetic material that mimics deformable, breakable polygonal grains cemented along their adjoining sides with deformable, breakable interfaces modeled as smooth-joint contacts. In this paper, a GBM utilizing a parallel-bonded base material is calibrated to match both st and sc of Lac du Bonnet granite and then used to simulate a Brazilian test. The Brazilian strength (sB) is slightly overestimated and the failure mode includes ductile post-peak response that is not representative of what occurs in laboratory Brazilian tests. By reducing the grain tensile strength, grain failure occurs during the Brazilian test and a more realistic failure mode that includes brittle post-peak response is obtained. However, the unconfinedcompressive strength of the modified material is too low. Sensitivity analysis on the grain and grainboundary strength properties demonstrates that the grain tensile strength controls the sB/sc ratio. Because the grain strength is controlled by the parallel-bond properties and the lowest achievable st/sc ratio in a parallel-bonded material is ~0.25, it is concluded thatsc, st and sB for a typical brittle rock cannot be matched with a GBM that utilizes a parallel-bonded base material.

Jun 1, 2012

By C. K. Wilton

"The Agnew Lake uranium deposits were discovered in 1953 following the discovery of the Elliot Lake deposits to the west. The original property was optioned to Kerr Addison Mines Limited who added additional claims by staking. Agnew Lake Mines Limited was incorporated in 1967 to develop the property and a shaft was sunk to 1040 metres and five levels developed before work was suspended due to low uranium prices at the end of1970.In 1974-75 the mine was dewatered and production started in 1977. By 1978 reserves were estimated at 10,000,000 tonnes averaging 0.35 kg. U10 , per tonne. Underground operations were terminated in 1980 although a uranium leaching operation was continued until early 1983.The deposits lie near the contact of Huronian metasediments with underlying Algoman granite. The sediments consist of arkose, conglomerate, argillite and quartzite with the uranium mineralogy mainly confined to oligomictic quartz pebble conglomerate. The higher uranium values are related to conglomerate with highest percentage of pebbles. The chief uranium minerals are uranothorite and monazite. It is of interest that the uranium thorium ratio differs appreciably from that of the Elliot Lake deposits. This fact along with the fact that the Elliot Lake sediments were deposited by paleocurrents from the northwest whereas the Agnew Lake sediments were deposited by paleocurrents from the northeast indicates widely separate sources for the deposits. It is suggested that the Agnew Lake uranium deposits are syngenetic placers deposited under anoxygenic atmospheric conditions."

Jan 1, 1986

By C. S. Crocker

The Centennial orebody was discovered and named in 1970, Manitoba's centennial year. It is relatively small, about 2 million tons. Strike length varies from 400 to 600 feet and widths from 10 to 60 feet; dip is 75 degrees. Low grade and metal prices demanded low-cost mining, and the mine was developed for conventional sublevel stoping. As the ore lay entirely under a large lake, ground movement had to be avoided and the stopes were to be filled hydraulically. Late in 1973, vertical crater retreat mining was introduced at Inco Limited, Sudbury, to recover pillars between filled stopes. It proved satisfactory and the results were publicized by CIL, who developed the technique. The method seemed to offer some advantages and one stope at Centennial Mine was selected to be mined by VCR while production was maintained from blasthole stopes. The trial stope was safe and showed lower development costs, reduced drilling time, a favourable powder factor and good fragmentation. VCR mining is now an accepted method at HBM&S Co., Ltd., and its use is being extended.

Jan 1, 1979

By J. D. Jones

The geographic occurrence of economic mineral deposits presents a variety of problems in modern tailings disposal operations. This paper presents case histories in several sectors of the mineral industry as well as the several stages of operations planning required for new designs, system expansion, reactivation of abandoned systems and upgrading to present environmental standards.

Jan 1, 1978

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By Raymond B. Hryciuk

Environmental auditing has evolved rapidly over the last decade — first in North America, then Europe, and most recently in Asia — into a widely practiced discipline designed to provide senior management with assurance that operations are being managed in compliance with established governmental standards, internal company policies, and good industry practices. This paper first examines the evolution of environmental auditing, focusing in particular on three interlocking driving forces: company initiatives, collaborative industry initiatives, and government initiatives. Characteristics of effective audit programs, those that have emerged among the leaders, are discussed, including: objectives, scope, coverage, approach, staffing, and organizational considerations. The author then addresses important future trends and developments for environmental audit program design, content, and coverage.

Jan 1, 1996

CSIRO Minerals, in association with the AJ Parker CRC for Hydrometallurgy, has an active program of hydrometallurgical research in which physical and computational modelling are used to better understand and improve a range of different unit operations. The modelling is based on flow simulation (Computational Fluid Dynamics or CFD), but incorporates other physical and chemical phenomena of importance, such as droplet break-up and coalescence, species transport and reaction. This paper reviews some of the major projects that have been undertaken at CSIRO Minerals and will illustrate the critical importance of hydrodynamics to the performance of unit operations and the improvements that can be made to performance using such modelling techniques. Unit operations that are discussed include solvent-extraction, gravity thickeners, flotation cells, bio-heap leaching and stirred tanks.

Jan 1, 2005

By W. Dong

This paper presents the fundamental study of the temperature distribution in a reforming planar solid oxide fuel cell (SOFC) using mathematical modeling and experimental testing approaches at Versa Power Systems (VPS). In order to investigate the on-cell temperature distribution under high rates of Natural Gas direct internal reforming (DIR), both the computer simulation approach and the experimental testing approach have been developed. In this work, comprehensive in-house DIR and SOFC models were developed and employed for the computational fluid dynamics (CFD) based 3D computer simulation. The current SOFC module has been corrected to take into account both the on-cell electrical leaking effect and the stack stage structural resistance. Meanwhile, an instrumented single-cell test jig with multiple thermocouples was built, and a series of experimental tests were performed at various conditions. The numerical results based on the single-cell jigs are in very good agreement with the physical test results.

Jan 1, 2005

By B. N. Church, R. H. Seraphim, J. T. Shearer

"The Lexington-Lone Star CU-Au deposits straddle the Canada U. S.A. border, south of Greenwood, British Columbia. This 3 km long linear porphyry system occurs in a northeast dipping belt of sheared quartz porphyry and serpentinite. The best grades of mineralization occur in three principal bodies known as the Pit zone, the Northwest zone and the Lexington Main zone. The Pit zone at the Lone Star mine is the largest of the mineralized bodies and consists of fracture fillings and disseminations of pyrite, chalcopyrite and minor molybdenite, hosted by the Lexington quartz porphyry. The Northwest zone, discovered by drilling through overburden near the 49th Parallel, consists of pyrite-chalcopyrite-gold mineralization in the quartz porphyry and the footwall serpentinite. The Lexington Main zone has the highest grade of gold and occurs near the footwall of the quartz porphyry with the mineralogy and setting similar to the Northwest zone. Alteration of the host quartz porphyry is mostly sericitic and chloritic; alteration in the adjacent serpentinite is mostly talc and carbonates.A weighted average of the drill-indicated reserves is 19.5 million tonnes grading 0.56% CU and 0.55 gl t Au.IntroductionThis paper describes copper-gold mineralization associated with the Lexington quartz porphyry in the Greenwood mining camp of south-central British Columbia and adjacent parts of Washington State (Fig. 1).Access to the property is mainly by a network of farm, logging and old mining roads to the U.S. border, 10 km south of Greenwood, British Columbia."

Jan 1, 1995

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By G. R. Parslow

U, Fe, Mn, Ni, Cu, Zn and Co data for the sediment in both Key and Seahorse lakes, which overlie portions of known economic uranium deposits in the region, are presented. With the exception of U, Fe and Mn, the elemental distributions can be considered anomalous, in a statistical sense, in both lakes. The U values are of particular interest in that Key Lake is not anomalous, whereas Seahorse Lake is markedly anomalous. Tentative correlations made with background data from other surveys in an attempt to differentiate between anomalous and background values indicate that deviations from linearity in a distribution, and not absolute mean or maximum values, are indicative of anomalous samples within the distribution.

Jan 1, 1979

By Jaime Meléndez Martínez

Recent interest in unconventional reservoirs motivates our work in laboratory measurements of seismic anisotropy. Seismic anisotropy is the variation in speed of a wave as a function of its direction of propagation. Analyzing anisotropy in unconventional reservoirs is important since anisotropy leads, for example, to differential stresses upon loading and could affect hydraulic stimulation (Reinicke et al., 2010, Zimmermann and Reinicke, 2009); in this sense, laboratory measurements are an important tool to study seismic anisotropy at small scales which can aid in the characterization of larger formations. The purpose of this work is to describe the laboratory methodology used to simultaneously measure ultrasonic P and S-waves in three different directions from a single core sample. Elastic anisotropy of a Proterozoic sedimentary rock from south-west Alberta is investigated. In metamorphic rocks seismic anisotropy is caused by preferred mineralogical alignment or foliation. Assuming a transversally isotropic medium, arrays of compressional and shear piezoelectric ceramic transducers were mounted on a sample trimmed from a core to measure travel times of ultrasonic P-waves and S-waves as a function of confining pressure at directions perpendicular, parallel, and oblique to the plane of foliation (bedding). Results show strong anisotropy agreeing with the assumption of a transversely isotropic medium. Dependence of travel times and hysteresis effects can be observed when pressurizing and depressurizing.

Jun 1, 2012

By R. ZapataN.

"In the following report, Altonorte Smelter owned by Xstrata will explain its experience with its denominated furnace called ""Continuous Altonorte Reactor"" since started up in March 2002. The Reactor is the main and only smelting furnace since the operation of Reverb Furnace was stopped (15 days after the start up of the Reactor) and it can be operate with dry concentrate for injection by tuyere and wet concentrated via Garr Gun when the injection system fails. From the started up of the Reactor, three operational campaigns have been carried out where in each one they have been increased their smelting throughput and availability. The flexibility reached by the technology bath smelting has allowed a high level of smelting of concentrate and revert materials. The high availability of the Reactor and overcoming problems that were considered of high complexity like the extraction of white metal and slag, refractory campaign, etc. has allowed the Altonorte smelter to project to smelting 1,200,000 tonnes per year with its only Reactor in next year."

Jan 1, 2007

By Claude Gosselin

En 1995, la Compagnie minière Québec Cartier a mis de l'avant un projet de recherche sur la modélisation de l'écoulement des gaz pour ses fours de frittage à l'usine de bouletage de Port-Cartier. Cette démarche s'inscrivait dans un large processus de collaboration avec l'Université Laval et le Consortium de Recherche Minérale (COREM). L'usine de bouletage possède deux fours de frittage d'une capacité moyenne de 600 tonnes/heure pour chacun des fours. Les fours de frittage sont des systèmes complexes d'échange de chaleur qui fonctionnent à contre-courant (le débit de boulettes versus les débits de gaz). Pour rencontrer les spécifications reliées aux propriétés mécaniques des boulettes, le processus de fabrication requiert des mesures et un contrôle des systèmes très précis. L'information fournie par plus de 70 capteurs (pression, température, puissance, vitesse, hauteur de lit, position de volet....) est utilisée pour manipuler une vitesse de grille, cinq ventilateurs et neuf zones de brûleurs. Malheureusement, les variables qui influencent fortement les mécanismes de frittage, c'est-à-dire les débits de gaz dans les différentes zones du four ainsi que la masse de boulettes qui circulent ne sont pas mesurées. Une méthode est donc proposée pour une estimation en ligne de ces variables. La méthode est basée sur un arrangement de 65 équations reliant pressions, températures et débits de gaz dans les conduites, les ventilateurs, les sections du lit et les fuites (Gosselin, 1998). Pour des raisons de simplification de cet article, seul un sous-système du four sera présenté. Les techniques de réconciliation des données reliées à la conservation de la matière et de l'énergie montrent que la mesure en ligne du débit de boulettes mène à l'estimation des débits de gaz et apporte des avantages intéressants pour le contrôle des variables stratégiques des fours.

May 1, 2001

By S. A. Bradford

The twenty years before World War I was the Golden Age of copper smelting in British Columbia. In this short time, the smelters developed from small, primitive units to large, efficient operations. The first copper claims had been staked on Howe Sound and Knight Inlet in 1864, and there was extensive copper mining in the interior by the mid-1880s, but before 1895, all ore was shipped out of the country for smelting, converting and refining. The first interest in smelter construction was undoubtedly inspired by a Provincial bonus and Dominion land grants offered to smelter builders. The early smelters made use of small blast furnaces which were designed to smelt any kind of ore, but usually far too little ore was available. The first smelter seems to have been the McRae furnace on the Spillimacheen River (1883), followed by Vancouver (1889), Revelstoke (1891), and Golden (1891) (1). They each smelted a few tons of galena and then quickly closed down permanently for lack of ore. Only smelters that actually produced some copper matte are described in the following sections.

Jan 1, 1999

By R. A. L. Drew, G. Mendoza-Suarez, J. Filipi, R. Vintila, J. A. Kozinski

Economics and environmental considerations along with the increasing demand of hydrogen encourage development of novel technologies such as plasma processing of hydrocarbons and thermal cracking of natural gas. Plasma discharges, either in thermal or non-thermal regimes are expected to allow low temperature and fuel flexible on-site hydrogen generation. The main drawback of thermal plasma reformers is the high-energy consumption resulting from high-temperature operation. On the other hand, non-thermal plasma, generated by dielectric barrier discharge (DBD), is able to simulate the chemical reactions employing much lower energies than those required by thermal treatment processes. The non-thermal plasma process allows for instance, a direct conversion of methane into hydrogen and carbon black with no CO2 release. The focus of this research was on the GHG-free method of H2 generation in compact non-thermal plasma reactors using low, medium and high permittivity dielectric ceramics. A stable, non-thermal plasma was generated by placing a dielectric ceramic between two electrodes with a 25 thou gap and applying an alternating current of 1-5kHz and voltages of 4-8kV. In order to ensure energetic efficient plasmas, experiments were conducted to analyze the behaviour of different permittivity ceramics. It was found that the dielectric properties of a ceramic, when used in a DBD reactor, have a strong influence on the discharge characteristics, which in turn influence the power consumption. Higher dielectric constant resulted in higher conversion rates of methane (higher yield of hydrogen and carbon). At the same time, the mechanical properties of the dielectric material, which are closely associated with its processability, influenced its resistance to electron bombardment, as well as thermal and mechanical damage. Therefore a reliable ceramic should have good dielectric properties, in addition to good thermo-mechanical stability.

Jan 1, 2004

By M. Kamyab

The Deep Exploration Technology project, as part of the Australian Cooperative Research Centre, is developing technologies to drill deep boreholes for mineral exploration purposes. The aim of the initiative is to transfer drilling technologies from oil and gas into mining applications. Several modifications have to be pondered due to this technology exchange: smaller cuttings sizes because of using impregnated diamond bits; narrower annulus space; higher drilling fluid velocity and likelihood of turbulent flow regime in the annulus; and higher pressure loss. In particular the results of our lab experiments have shown that the increase in concentration of small size cuttings can significantly change the rheology of the mud when drilling in hard rocks. This, in return, could have a noticeable increase in the pressure loss encountered along the annulus space. As a continuation of the above study, numerical simulations were conducted to investigate the cuttings transport behaviour in small size annulus space. Fluid velocity, annulus size, cuttings concentration, cuttings density, and cuttings size were some of the parameters that were varied to see their effects on cuttings transportation and the pressure loss along the annulus space. The results indicate that, due to the differences between oil and gas and mining drilling, conventional oil well planning is not applicable for mineral exploration drilling and numerical simulation would help in this matter.

Aug 1, 2013