Search Documents

By H. S. Wilson

"The property owned by the Lamaque Mining Company comprises a group of forty-four claims and fractions occupying an area of about 2,458 acres, in west-central Bourlamaque township, Abitibi county, Quebec. It is on ,the outskirts of the towns of Bourlamaque and Val d'Or, about 70 miles east of Noranda, near the eastern end of the belt of greenstones of Keewatin and Timiskaming age that extends eastward through Kirkland Lake into northwestern Quebec, terminating in Haig and Jurie townships 40 miles to the east.The claims on which the orebodies occur were first staked in 1923; No. 3 vein was discovered the following year. The original discovery was made by R. Clark in 1923. This was a small quartz vein containing a pocket of coarse gold on the north side of a hill near the northwestern corner of block 3. It is said that all the gold was removed in one shot in blasting into the vein; elsewhere it was barren. A picket line was then run west along the strike of the vein, which occupied a narrow shear zone, and about 2,000 feet west, in prospecting on either side of the picket line, a large boulder of quartz and tourmaline containing visible gold was found. This led to more intensive prospecting by trenching in the vicinity with the result that the No. 3, or 'float' vein, about 250 feet north of the boulder, was found. Due to low ground this vein was exposed in only one trench. The only other important vein found on the surface was the No. 1, or H, vein, which was exposed in several places by stripping and trenching, but it did not carry appreciable amounts of gold."

Jan 1, 1954

By J. Lipp

The lion share of lithium produced globally originates from South American salars. The standard operation for lithium production utilizes an array of evaporation ponds. This process consume vast areas and is either very slow when relying on solar evaporation - roughly 18 months of residence time; or with very high energy consumption since over 90% of initial water volume needs to be evaporated. A new technology, based on solvent extraction was developed. Results indicate a distribution coefficient up to 30, and selectivity greater than 1,000 towards Na extraction. The loaded solvent is stripped using a strong mineral acid, and the product solution is the lithium derivative of that stripping acid. Utilization of this new LiSXTM technology results in reducing the area needed for a commercial plant as well as reduces the residence time. In addition applying different stripping acids can diversify the product line of such facility.

Jan 1, 2014

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"Potentially economic deposits of rare earth elements (REE) often contain elevated levels of naturally occurring radioactive materials (NORM), primarily thorium and uranium and their associated radioactive decay products. The concentrations of NORM usually exceed typical background levels of natural radioactivity, sometimes by factors of ten or more, and can be of concern relative to occupational radiation protection and the management and disposal of REE mineral processing and metallurgical wastes. This paper provides a summary of the radiological issues normally encountered in the REE concentrate production industry. In addition to an introduction to background radiation and radioactivity, including the thorium and uranium radioactive decay series, radiation levels expected to be encountered in REE concentrate production are outlined. The occupational, environmental and regulatory aspects of REE production related to NORM, including radiation dose limits, radioactive waste disposal guidelines, and threshold VALUES (for the application of transport regulations, are presented.INTRODUCTIONConcurrent with the increasing demand for new sources of rare earth elements (REE) to meet modern industrial needs, there is also an increasing awareness of the radioactivity associated with the REE ores and resources. This is an especially important consideration in addressing questions from the public and local communities who are often concerned about “radiation” and “radioactivity”. Public concern is heightened by reference to legacy issues that arose during times of less regulatory oversight; as well, the benefits of modern technologies, practices and regulation are overlooked. Such concerns are also often inflamed by unfounded claims by non-governmental organizations (NGO’s). Thus, it is important that all concerned have a full understanding of just what the potential risks from radiation associated with REE are, or are not. This paper provides an overview of the sources of radioactivity, the potential implications of radiation and radioactivity in the REE industry, and a brief discussion of established and reliable methods of managing exposure to radiation and radioactivity."

Jan 1, 2012

By A. R. Byers

"Porcupine Peninsular mine is at the extreme southwestern end of North peninsula in Night Hawk lake, Cody township, Ontario. It lies approximately 10 miles east of the gold-producing district of Porcupine.Gold in quartz veins was discovered on Gold -island in Night Hawk lake in 1906, the same year in which the now famous Porcupine gold camp was discovered farther west. Most of the claims now held by the Company were originally staked by Charles Auer in 1907, In 1910 when the level of the lake was exceptionally low, gold was discovered in a quartz vein near the shore and close to the present mine shaft.The mine is developed by a main shaft to a depth of 440 feet, with levels at 80, 180, 300, and 425 feet vertical depth and by a winze to 630 feet. A mill of 200 tons daily capacity was built during 1923, Production commenced on January 4, 1924, and continued without interruption to May 31; 1926, when operations were suspended due to a decrease in the grade of ore. Total production amounted to 27,416 ounces of gold from 99,708 tons of ore, an average grade of 0.275 oz. a ton. Diamond drilling and re-sampling of the mine during 1934 and 1935 indicated approximately 1,480,000 tons, having an average grade of 0.123 oz. gold a ton, above the 625-foot level."

Jan 1, 1954

By M. Bourassa, P. Roy

"This paper describes the automation of Kiena's grinding circuit which comprises an open SAG mill circuit and a closed ball mill circuit with two stages of hydrocyclones. The circuit has been instrumented according to a two level control strategy.The regulatory control strategy is implemented in an industrial controller. This controller does data filtering and calculation (flowrate and solid content) and regulates the pump box levels (2), the water additions: or the pulp percent solids (4) and the fresh ore feed rate.The supervisory control calculates for the industrial controller, the fresh ore feed rate setpoint and the pulp percent solids setpoints in order to optimize the grinding circuit operation. It is made of two modules, one for data filtering and one for control optimization. The filtering program uses modern tools to adjust the measured value and estimate missing data (dynamic material balance, on line estimation of model parameter, etc.). The control program acts as an expert system which combines the benefits of model-based control and rule-based control. A multivariable predictive controller (DMC) is used to maintain the circulating load and the hydrocyclones feed percent solids (which is correlated to particle size) while the rule-based control validates the previous output, detects and avoids the SAG overloads and sump pumps overflows.The system has been operating since MAY 1992 and the benefits obtained are discussed.INTRODUCTIONIn 1990, Les Mines d'Or Kiena decided to go ahead with a project for automating its grinding circuit as proposed by the Centre de recherché minerals (CRM). Its objectives in doing so were to marginally increase production capacity (1 % ) and to create a new challenge for plant staff. The main stages of the project, which involved CRM, Kiena Mines and a consultant, are shown in Table 1. The project was completed in May 1992 with the implementation of a supervisory control system. This text describes the main features of the system with a special focus on its most innovative aspects."

Jan 1, 1993

By A. Perucho, J. P. Harrison, A. Bedi, L. Alejano, L. Lamas, A. Sofianos, A. M. Ferrero, R. Migliazza, R. Olsson, J-F. Mathier

"In 2010, the Eurocode for Geotechnical Design, EN-1997-1:2004 (CEN, 2004), informally known as Eurocode 7 or EC7, became the Reference Design Code (RDC) for geotechnical design – including rock engineering design – within the European Union (EU). EC7 is one standard within the comprehensive Structural Eurocode suite, which as a whole has been also adopted by a number of other countries beyond the EU. EC7 is thus becoming a key design standard for geotechnical engineering worldwide.As part of the Structural Eurocode suite, EC7 requires designs to adhere to the principles of Limit State Design. However, it is not clear that current rock engineering design practice can satisfy this requirement. In addition, evidence is accumulating that EC7 is currently difficult to apply to, and may even be inappropriate for, rock engineering design. These issues may be due to the fact that the development of EC7 to date took place without any formal input from the international rock mechanics and rock engineering community.In early 2011 under the auspices of CEN (Comité Européen de Normalisation / European Committee for Standardisation), EC7 entered a formal period of maintenance which was aimed at improving the applicability and ease-of-use of the Code. This maintenance cycle will conclude in 2020 with the publication of a revised version of EC7.This paper describes a number of critical aspects for rock engineering in the context of EC7, inparticular the following:– the history of the Structural Eurocodes and the concepts they embody;– the nature of Limit State Design and the challenges and opportunities it poses for rock engineering design;– the formal means by which the Structural Eurocode maintenance cycle proceeds;– the plans currently being developed for improving EC7 with regard to rock engineering design and construction;– the unique and vital opportunity for the entire international rock mechanics and rock engineering community to comment on the Code and make suggestions for its improvement."

Jan 1, 2015

By Laura Kelsey

Contaminant Robust In Situ Water Extractor CRIWE Nafion-based water clean-up Extract purified water from natural extraterrestrial sources In situ water processing for downstream electrolysis Chemically resistant to process contaminants such as acid

May 1, 2013

By Unkown

The Province-wide road ban on movement of heavy loads has had the effect of curtailing or stopping development in several areas. In the Leduc area, the discovery well has been restricted in flow to only a fraction of normal due to limited storage space, but drilling at Imperial Leduc Nos. 2, 3, and 4 has been continued for the past few weeks. The No. 2 well is within 100 feet of the producing horizon and should be completed within the next few days. According to reports, it has been logging slightly lower, structurally, than the discovery well, but, regardless of the outcome, it has been an important test to determine westerly cross-section of the Leduc structure. No official reports have been made available of any tests made during the drilling of the well, but it is understood that promising oil and gas shows have been indicated in higher formations. Actual drilling operations have not been commenced by any of the other companies holding leases in the immediate area but it is expected that, when road bans are removed and equipment is assured, several wells will be commenced. Announcement has been made that Imperial Oil, Limited, will drill a well near Battle lake, about thirty-five miles southwest of the Leduc field. Location of the well has been made following an extensive seismograph survey of the area, with total depth of the test well expected to be in the 8,000- to 8,500-foot range. Drilling will be done with the heavy-duty rig last used at the De Winton test. Imperial Oil have abandoned hope of oil production in the Provost area after drilling nine wells, but will retain their interest in the gas field that has been developed. Of the wells drilled, four indicated gas flows ranging from 1,060 to 13,200 M.c.f. per day.

Jan 1, 1947

By F. Habashi

"Extractive metallurgy was divided into the three sectors pyro-, hydro-, and electrometallurgy in 1959 when Professor Joseph Newton at the Idaho School of Mines in Moscow mentioned this in his book Extractive Metallurgy. Pioneer hydrometallurgists who built this discipline can be traced to the alchemists in the ninth century. It is now a mature subject of great importance in which pressure plays a vital role. Short biographies of some hydrometallurgists and the processes they invented are briefly outlined.INTRODUCTIONHydrometallurgy is the use of aqueous solutions to recover metals from ores. It is a relatively new discipline when compared with pyrometallurgy the use of fire to melt ores and recover metals which was practiced in ancient times. Hydrometallurgy can be traced to the time of alchemists whose concern was the transmutation of base metals into gold. Although alchemists did not succeed in their venture yet they described many reagents that are useful today. For example, they prepared sulfuric acid by distillation of iron vitriol, muriatic acid by distillation of sulfuric acid with salt, and nitric acid by reaction of sulfuric acid by reaction of sulfuric acid with salpeter. Jabir Ibn Hayyan the Muslim alchemist who lived in the ninth century (Figure 1) described aqua regia a mixture of nitric and hydrochloric acid that can dissolve gold although either acid has no action on gold. THE MIDDLE AGESIn the Middle Ages, it was reported that copper was recovered at Rio Tinto in Spain by allowing copper-containing pyrite to be exposed in piles to the action of air and rain. Copper sulfate solution obtained was treated with pieces of iron to precipitate metallic copper—a process that was called cementation. Georgius Agricola (1494–1555) (Figure 2) a medical doctor in Saxony who used to visit mines and smelters to examine miners and metal workers, described in his book De Re Metallica the parting of gold, i.e., separating of silver from gold by acids."

Jan 1, 2016

By D. C. Rance

"The Quintette Coal Limited property is located in the northeast coal area of British Columbia.A basic agreement with the Japanese steel industry was executed on January 27, 1981 for the sale of 69.5 million tonnes of Quintette metallurgical coal over a 14.5-year period. This contract period can be extended by five years by mutual agreement. Sale agreements have also been signed for the sale of 19.4 million tonnes of oxidized coal over a 15-year period.Work started on site development in the late summer of 1981, and at present, two of the four eventual pits-the McConkey and Frame-are under development.The pits are currently in a prestripping phase. These pits are notable for the stripping volumes that have to be removed from relatively small pit areas. In order to provide for the required detailed rapid short-range planning of these pits, engineering will be computerized, as will the truck dispatch system.The mining area lies 21.1 km from the plant site by road and the transport of raw coal to the plant is by means of a high-speed conveyor system which has a total length of 13.4 km with a vertical drop of 740 m.The surface plant facility was designed on a modularized basis to facilitate maintenance, and is designed to enable the use of gravity f low of raw coal and heavy media in the plant to minimize the use of pumps.The construction of the plant and mine site facilities is ongoing, and the first coal production is scheduled for early December 1983.IntroductionQuintett e Coal Limited is a Canadian company incorporated in the province of British Columbia in 1971. Denison Mine s Limited is the manager of Quintette's activities. Equity in Quintette Coal Limited is held by several shareholders, with interests as follows: Denison Mines Limited, 50%; Charbonnages de France International S.A., 12%; and Japanese interest, 38%."

Jan 1, 1983

By G. Macfarlane

"In 1985, a crushing plant, located in the feed preparation area of Kidd Creek's copper smelter, was modified. The plant, which originally had treated only copper-bearing materials for the smeller, at a rate of 10 tonnes per hour, was expanded to 40 tonnes per hour capacity and modified to treat silica ores to meet the smelter’s flux requirement and also gold ores from the company's Hoyle Pond property. In the storage area adjacent to the crushing plant a 300 tonne per day gold mill was constructed.This paper outlines the construction and first year of operation of the crushing plant and gold mill with emphasis placed on the capital and operating advantages to be gained by utilizing an existing metallurgical infrastructure.IntroductionThe Kidd Creek Mines Ltd. copper-zinc-silver orebody is located 24 km north of Timmins, in Northern Ontario . Mining of this massive sulphide de posit commenced in 1966 and, in the ensuing years, a concentrator and zinc plant were constructed at the metallurgical complex, approximately 17 km by rail from the mine site . At this same site, in 1981, a copper smelter and refinery were commissioned. The smelter which utilizes the Mitsubishi smelting process for the continuous production of blister copper from copper concentrate, has been comprehensively described in previous papers.At the time of the smelter construction, a small (10 tonnes per hour) crushing plant was installed in the smelter's feed preparation area. This plant was used to treat the copper-bearing revert material produced by the smelter, and, apart from periods when slags and matte were produced through furnace drainage at the end of each operating campaign, it was generally under-utilized. This fact, together with the requirement to devise a more cost effective method of providing silica flux for the smelting operation, was the basic rationale for modifying and expanding and crushing plan t. At the same time, development at Kidd's Hoyle Pond orebody had progressed to such a stage that a gold mill of 300 tonnes per day was warranted."

Jan 1, 1988

By Rodrigo Madariaga, Tracy T. Morris

The practice of stripping copper starter sheets from titanium blanks to be used in a conventional electrolytic tankhouse has been around since the advent of Electrometallurgy. Historically it has been done manually, utilizing many people to produce in some cases thousands of starter sheets per day. Some other conventional tankhouses have successfully converted to using mechanical means to strip starter sheets or have made the switch to permanent cathodes and although robotics have been around for quite some time they have not been used to strip starter sheets until recently. The Amarillo Copper Refinery began using robotics to strip several years ago and the details to how this came about and how the robots work will be described. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

By P. E. Weidmark

"PART 1-Published PapersAllcott, G.A., and Archibald, D.E.; ""Description of pillar behaviour at Heath Steele Mines""; Can Min Metall Bull; 74:834:80-87; 1981.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of rock Mechanics; 3:32-33; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:37-38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:38; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses"" ; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:41; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:42; 1979.Baar, C.A.; Discussion of Theme 1: ""Physical properties of intact rock and rock masses""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:46; 1979.Baar, C.A.; Discussion of Theme 2: ""Tectonophysics""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:60; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3: 116; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:116-117; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:117; 1979.Baar, C.A. '; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:118-119; 1979.Baar, C.A.; Discussions (2) of Theme 4: ""Underground openings""; Proceedings 3rd Congress lntnl Soc of Rock Mechanics; 3:119; 1979.Baar, C.A.; Discussion of Theme 4: ""Underground openings""; Proceedings 3rd Congress Intnl Soc of Rock Mechanics; 3:120-121; 1979."

Jan 1, 1982

By Donald J. MacNeil

THE opinion, based upon geological knowledge, that certain areas within the Province of Nova Scotia might yield commercial quantities of petroleum, is not new. It dates back to at least 1864, when the Pioneer Oil and Salt Company drilled some shallow holes in search of oil near lake Ainslie, Cape Breton. As a matter of fact, several companies were engaged in oil exploratory work near lake Ainslie at about that time; included among them were the Inverness Oil and Mining Company, the Victoria Oil Company, the American Oil Company, and the Cape Breton Oil and Mining Company. Oil exploration by these and other companies was conducted sporadically on Cape Breton island until 1914. In several instances, the depth of the test holes exceeded 1,000 feet; the deepest was carried to 3,260 feet. The Lake Ainslie area was selected because oil seepages were present along certain sections of the lake shore, but the tests that were drilled to tap the oil-bearing zone failed to yield anything of commercial value. Currently, there are three areas in Nova Scotia wherein active exploratory work is being conducted, namely, at Pugsley Siding close to Amherst; at Kennetcook, Hants county; and near Mabou, Inverness county. The Pugsley Siding test is being drilled by the Sun Oil Company, of Philadelphia; the work at Kennetcook is under the direction of the Nova Scotia Oil and Gas Company; two relatively deep holes were drilled by the Lion Oil Refining Company in 1944 near Mabou, and, as a result of the additional geological information derived therefrom, another test probably will be drilled by this Company in the same area. Aside from these activities in the search for petroleum, the oil possibilities of several other sections of the Province are being studied by means of surface geological mapping.

Jan 1, 1945

By P. C. Parsons, G. C. Milligan

"IN FIELD WORK in the Cape Breton Highlands, which are heavily covered with vegetation, it is necessary to run traverses along the valleys of small brooks. We encountered difficulty in closing such traverses, and the following technique was developed to solve this problem. It has been tested in the field for four seasons by several people, and found to be simple, efficient and more accurate than any other compass-and-pace system of which we are aware. So far as we can find, the technique has not been described previously. It may be of use to others.The Cape Breton Highlands of Nova Scotia consist of hills of old intrusive and metamorphosed sedimentary rocks protruding up to 1,000 feet above the general level of the younger sediments which underlie the valleys. The flat hill-tops are the remnants of a plateau; drainage off the edge of this plateau has produced many small steep brooks. They occupy valleys which are up to 800 feet deep, and V-shaped in cross section, with steep sides covered by mixed conifers and hardwoods. The stream at the bottom is rarely more than a few feet wide, with a negligible meander belt, but with many bends, rapids and falls. Visibility along the stream, in consequence, is rarely more than a few hundred feet, and in many places much less.It was found impractical to map the streams by the method of meander lines, as described in many standard surveying texts and hand-books. The limited visibility, and the numerous bends of the brooks, necessitated many corners. Every corner introduces errors. To 'close' a survey with 40 or 50 such corners proved either very time-consuming or impossible. In most cases, however, the general direction of a valley may be obtained from an aerial photograph, or by direct observation, and this became the basis of the method adopted."

Jan 1, 1971

By Donald F. MacDonald

THE cement plant nearest to Nova Scotia is not far from Montreal. Cement is a heavy product which, because of its relatively low value, cannot stand a high freight charge without unduly enhancing its cost. This is one reason why cement costs are high in Nova Scotia. The regular retail price per bag (8772 lb.) in Antigonish is 85 cents, which would be $3.40 per Canadian barrel of 350 pounds, or $3.65 per American barrel of 376 pounds.It is said that the lowest wholesale price in Halifax is 65 cents per sack, which would be $2.60 per Canadian barrel or about $2.80 per American barrel. According to U.S. Bureau of Mines statistics, the average factory price for cement in 1937 was $1.48 per American barrel, which is practically the same as the value per barrel indicated in Dominion statistics for the Canadian output during that year. The difference between $3.40 and $1.48 is $1.92. It is evident that the average user of cement in the Mari-times pays a stiff premium because Maritime cement raw materials have not been developed. Rock-wool, the manufacture of which is rapidly increasing in Ontario and the United States, is much needed for building insulation in the cold climate of Nova Scotia.

Jan 1, 1939

By J. K. Armstrong, C. Feyerabend

"As mines are constantly growing and expanding, so do the challenges for emergency response teams. They have to keep up with the pace set by current and future production techniques. Although mines have now reached depths of several kilometres and their dimensions and complexity are that of an entire city, mines rescue still must be able to reach the most remote areas within the mine in a swift and safe manner. The duration of breathing apparatus and physical human capabilities are limitations. Therefore, alternative methods have to be explored to extend the time under oxygen for mine rescue teams without putting additional stress on the team members. To address this global trend, Dräger, Goldcorp and PAUS have partnered to develop a mine rescue vehicle that allows mine rescue teams to travel for an extended period of time through a contaminated atmosphere without the use of breathing apparatus, thus extending the range of their mission. By applying currently available techniques, the safe expansion of mine production can be ensured, giving mine rescue teams the ability to respond to accidents in a safer and faster way. INTRODUCTION With the reduction of easily accessible natural resources, there is a global trend toward searching for higher ore grades underground and/or continually expanding mines underground to extend their lifetime. While in some areas this trend has just begun, in other countries mines are reaching depths or horizontal dimensions that pose extreme challenges (Codelco, 2016). These challenges include safety relevant topics, such as rock stability, heat and seismicity, but also more basic issues such as distances to the working face, which can become crucial considering the cost to develop a new shaft or decline. To overcome this, there is a growing interest in collaboration among various stakeholders to drive the development and support of deeper mines and tackle the complexity of underground mining. This is evidenced by the fact that several industry and research groups and networks have formed, e.g. the I2mine project in Europe and the Ultra-Deep Mining Network by the Centre for Excellence in Mining Innovation in Canada. Due to commodity pricing and the trend toward renewable energy, metal/non-metal mining will be the driving force behind this development."

Jan 1, 2019

By M. E. Wilson, A. C. Lee

"The property owned by Senator-Rouyn Mines, Limited, is in Rouyn township about 17'2 miles southwest of the town of Rouyn. It adjoins the Chadbourne claims of Noranda Mines, Limited, on the south and the Bagamac property on the ·west. It includes seven claims-block 44, blocks 80 to 83 and blocks 96 and 97; the mine is wholly in blocks 44 and 82.Late in 1936 gold was discovered in an outcrop of rusty weathering carbonate rock near the north end of block 44, and the following year the present Company was organized to proceed with the development of the property. During 1937-38, 17,000 feet of diamond drill core were bored to determine the extent of the ore deposit at depth. From October 15th, 1940, to April 15th, 1941, the ore was hauled to the mill at the Arntfield mine for treatment. The mill on the Senator-Rouyn property started on April 25th, 1941, and has been in practically continuous operation since than time. To the end of 1946, 574,874 tons of ore, from which gold having a value of $3,836,450 was recovered, were treated in the mill.GEOLOGYThe rocks exposed at the Senator-Rouyn mine, except in the southern part of the property, are almost wholly quartz diorite, part of an irregular mass that extends west from the town of Rouyn along the north shore of Noranda lake and thence southwest across the Senator-Rouyn claims. In the northern part of the propertyt inclusions of rhyolite occur here and there in the diorite. In the southern part the predominant rock is dacite and in the east-central part of block 44 claim andesite. Dykes of andesite, quartz syenite, and later diabase also occur on the property.The andesite of the Abitibi volcanics is not exposed on the property, but has been intersected in three diamond drill holes, one on the eastern boundary of block 44 and two farther west within the block. This andesite is probably the western end of a band of pillowed andesite well exposed in the Larose claim to the east."

Jan 1, 1954

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

By Delio J-J Tortosa, Fred F. Langford

"The Cenex orebody occurs at the intersection of northwest and northeast-trending fault zones that formed during post-Hudsonian uplift. The ore is localized in breccia zones, along faults, and in veins and adjacent wallrocks. The host rocks are Tazin quartzo-fe/dspathic mylonites and ultramylonites and chloritesericite- quartz-graphite-feldspar mylonite schist. The uraniumbearing minerals are finely disseminated pitchblende and uraniferous titanate.The earliest mineralization may have been associated with /ate-stage retrograde metamorphism in the mylonite schist. The main stages of mineralization were associated with brecciation, hematization, carbonatization, and chloritization of the mylonites and ultramylonites. Uranium mineralization was clearly much later than any igneous or metamorphic activity associated with the Hudsonian orogeny.Late post-orogenic uplift, erosion, and deposition of the Martin continental clastics in fault basins were coeval with uranium mineralization. The deposit is consistent with a meteoric-hydrologic system constituting a source for orebearing fluids, hence the close spatial relationship of the uranium deposits in the Beaverlodge area with the basal unconformity of the Martin Group."

Jan 1, 1986