Search Documents

By R. G. Gillies, C. A. Shook, W. H. W. Husband

"The current state of knowledge concerning pipeline transport of coal in water slurry form is summarized for the four categories: coal-water fuels, conventional fine coal slurries, coarse coals and stabilized mixtures of coarse and fine particles. Surface chemistry is of dominant importance for coal-water fuels and considerable progress in understanding the role of surfactants has been achieved in recent years. Little generalized research on the flow of conventional fine coal slurries has been done in the past 17years, although innumerable conceptual designs and feasibility studies have been undertaken. Coarse coal slurries are fairly well understood but the model which explains their flow requires more data to be established fully. Stabilized flow mixtures should probably obey the same model as coarse coal slurries but experimental results for stabilized mixtures have not yet been incorporated in a comprehensive theory.IntroductionPipeline transportation of coal in a water vehicle has been employed for many years in coal washeries. It has been used less frequently in hydraulic mining and thermal power station fuel supply systems. The suitability of coal for pipeline transport arises from its moderate specific gravity relative to the carrier fluid and the fact that throughputs are often large and steady over long periods of time."

Jan 1, 1990

By Robert J-M Ethier

"Sequential blasting has been introduced at Mines Gaspe to reduce the harmful effects associated with the instantaneously primed blasting method. Three stages of modifications had been tried to improve this method: trials of a rectangular pattern instead of the square one, trials of lengthened hole collars at the perimeter of the blast and trials of increased inter-row delay intervals from 35 to 50 ms. Results showed that improvements to the instantaneously primed blasting method were limited by the probability of increasing the number of bootlegs.Doing these modifications allowed the definition of a general approach to improvements before the sequential blasting method was introduced. This general approach included: planning of the mining sequence, following up on the drilling, loading and tying-in of each blast, compiling and evaluating blast results, comparing results from one bench to the other and moving along with one change at a time. This approach has permitted the successful introduction of the sequential blasting method in two steps: trials of blast by rows of delayed holes and trials of hole-by-hole blasts. The optimum result has been analyzed by high-speed camera and by computer blast simulations, The actual optimum sequential blast is obtained with a CORDLINE priming system using period 15, permitted in a large drilling pattern, with an intersequences delay interval of 230 ms and an inner-sequences delay interval of 50 ms.While these modifications were being introduced, a careful study of the drilling and blasting costs was made, which showed a sharp reduction of drilling cost per tonne. Even though there was an increased use of packaged slurry the blasting cost per tonne also dropped. The reduction in cost per tonne was explained by the fact that the average energy factor was maintained while the blasting pattern was expanded.The sequential blasting method, successfully introduced at Mines Gaspe, permits blasts of better quality, reduces the drilling requirements by more than 30% and helps to achieve improved productivity while minimizing costs."

Jan 1, 1984

By D. A. Whitley, R. P. Carone

"Shaft sinking by blind shaft drilling offers the mining industry a different approach to shaft construction. Benefits of blind drilling include less construction time and fewer safety problems while being economically competitive with conventional sinking methods under certain conditions in soft water-bearing formations.Technology and equipment are available today to drill blind shafts up to 20 feet in diameter and over 3,000 feet deep. This is an extension of proven techniques developed by private industry. To drill a 20-foot-diameter hole requires a specially manufactured hydraulic drill unit with a rated hoist of 2 million pounds and 500,000 ft/lb of torque.This brief paper will discuss the following aspects of blind shaft drilling:• benefits;• equipment f or drilling;• circulation methods;• circulation rates;• shaft alignment; and• progress rates to be expected.IntroductionShaft sinking by blind shaft drilling offers the mining industry an improved alternative method for shaft construction. The drilling of 20-foot -diameter shafts to depth s in excess of 3,000 feet can be done by utilizing equipment specifically designed and manufactured for this purpose. This equipment is a distant cousin, at best, to standard oil well drilling rigs. The actual configuration of these drilling machines will be discussed in a following section.To most people, the drilling of mine shafts may seem to be a new or at least recent technology. However, as early as the I920s, German and Dutch miners were drilling 24-foot diameter shafts for coal mines. What led ""miners to resort to drilling were ground conditions that still plague conventional shaft sinkers today: soft , water-bearing formations. The major drawback to these early attempts was a low penetration rate due to poor bit cleaning. This, however, was not the end of early shaft drilling activity. From 1936 to 1950, a number of mine shafts were drilled by the calyx or coring method. This method employs a bit with a large bore down the center. As it drills, it cuts a core. When 5 to 10 feet have been drilled, the core is removed. The disadvantages of this method were the time and work involved in breaking the core free, and it was inadequate in soft water-bearing ground."

Jan 1, 1981

"Classification is an important aspect of mineral processing plants and if not operated efficiently can compromise both the throughput and recovery of the circuit. This paper discusses the benefits that can be obtained by operating the classification section efficiently. Since classification in most of the mineral processing plants is carried out using either hydrocyclones or screens the case studies involving the two classifiers were used in the discussion. Studies where optimising the classification circuit lead to improvements in the performance of the overall plant were included to show the benefits of paying attention to this area that is usually neglected. The data from the mill-float mill float, SABC, and Single Stage SAG mill circuit case studies have shown that the circuit throughput can be increased throughputs without compromising recoveries by optimising the classification circuit. On plants where the ore can be liberated at coarser sizes the experimental results have shown that replacing hydrocyclones with high frequency screens can lead to improved plant throughput with no detrimental effect on recovery. The discussion has included information on design and operational considerations for plants that have or intend to use hydrocyclones or screens that could make the classification circuit more efficient.INTRODUCTIONComminution is the process in which particles are reduced in size mainly by crushing and grinding. In most mineral processing circuits comminution is carried out to liberate the valuable minerals prior to subjecting the ore to a recovery process were values are concentrated or extracted (Mainza, Evertsson, Benzer, Tavares, Powell, Rule, Plint, …, 2013). Comminution is an energy intensive process and is usually achieved in stages. It is common to have a classifier after each comminution stage. The process is carried out in stages to minimize energy usage and to improve the efficiency of the process in meeting product specifications. Although comminution circuits have been advancing classification has remained a key component of the comminution circuit design (Mainza et al., 2013). Mainza et al. (2013) summarised the role of classification in mineral processing circuit as: to allow material in the equipment that can promote high operational efficiency, to improve material handling in the circuit, to minimize overgrinding of material to reduce energy consumption, and to provide the best quality product to enter the next stage of processing. Classification stages are employed in comminution circuits to ensure that high throughputs are processed without compromising the product quality or to produce a fine product at relatively low energy. If neglected classification can have detrimental effects on plant performance."

Jan 1, 2016

By M. Fiset, D. Belley

"In a country with a cold climate like Canada, the cost of replacing worn parts of snowplow equipment such as blades, is enormous. A great number of these blades, with different mechanical properties, are available, but few studies have been made to facilitate their selection according to the optimum ratio of wear resistance to cost. To attain this objective, laboratory tests have been developed to correlate test results with those obtained from various road service conditions. The test materials, 1080steel in different states, 1090steel and D2 tool steel were chosen to cover a large range of hardness as well as different microstructures. Comparison of the wear resistance of the test materials relative to a standard revealed, in general, a good correlation between the results of laboratory cement wheel tests and those from the road tests. Scanning electron microscope wear scars of laboratory and road test specimens were compared to determine if similar removal material mechanisms were active. IntroductionThe correlation between wear tests in service and those performed with the aid of laboratory equipment is of considerable interest. As a matter of fact, when correlation exists, it allows one to evaluate the performance of a material more easily and at a lesser cost.Several authors have been interested in simulating various wear circumstances, especially abrasive wear. In particular, the simulation of wear on implements working the soil, has been tried by several researchers. The test using the rubber wheel seems to be the one giving the best correlation if the soil is rather sandy and its moisture content is low.However, little work has been done concerning wear on the plates, skids and blades attached to trucks used for levelling and snowplowing; such equipment being used to keep roads clear in northern countries. Now each year, companies introduce new steels by claiming that the y are superior in performance to their predecessor s and invariably they demand a higher cost. The study presented here was undertaken with the goal of making a more judicious choice of these steels by simulating their behaviour in the laboratory. Moreover, the examination of abraded surfaces in situ and in the laboratory have also allowed us to compare the respective wear mechanisms."

Jan 1, 1988

By Peter N. Calder, Louise H. Michaud

"An interactive mine planning package has been developed to aid with the tasks involved in generating dragline mine plans. This package employs recent advances in PC-based,3D computer graphics and 3D geologic modelling. A Gridded Seam Model (GSM), capable of modelling rugged topography and multiple coal seams, including folding and faulting, is used to generate the geologic database This model is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal reserves and the removal of waste material.As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans and can allow for the evaluation of a number of mining options within a reasonable time frame.IntroductionThere are a large number of variables that must be taken into account during the development of a dragline mine plan. This is especially true when developing a mine in mountainous terrain, where there is a lack of continuity of the geology and topography over the mine site. Until recently, the complexity of dragline mine plans has prohibited the development of a universal mine planning package that is applicable to all geologic and topographic situations. The majority of the commercial programs that are presently available to facilitate dragline mine planning have been developed for specific mine properties or are limited in the coal geology and mining methods that they can simulate (Brown and Clifford, 1983; White 1983; White and Jones, 1984; Sadri and Lee, 1982; Dagdelen, 1979)."

Jan 1, 1993

By M. K. Abel

"The Strathcona Mine is located in Levack Township on the North Range ofthe Sudbury Basin. The main orebody consists of pyrrhotite-pentlandite-chalcopyrite mineralization associated with an embayment of the footwall of the Sudbury Irruptive. A zone of massive chalcopyrite-cubanite-pentlandite mineralization occurs in a complex vein system in a series of mixed gneisses and breccias in the footwall. Vein widths vary from a few millimetres to 6 metres. In December 1979, this zone was estimated to contain 976,000 metric tonnes, with a grade of 9.31% Cu and 0.46% Ni. The vein system has a general strike of N 68°W at an angle of 60 degrees to the average strike of the footwall contact of the Irruptive. The dip of the vein system is 45 degrees sw. The strike and dip of individual veins in the system coincide with the directions that would result if a compressive stress had acted in a direction normal to the footwall of the Sudbury Irruptive, producing a conjugate set of fractures. The strike of the Irruptive at the Strathcona Mine is parallel to the long axis of the basin.IntroductionThe Strathcona Mine, owned and operated by Falconbridge Nickel Mines Limited, is located in Levack Township on the northwest rim of the Sudbury basin (Fig. I) . It is one of a group of nickel-copper sulphide ore deposits present along an 8.2-km section of the North Range of the Sudbury Irruptive. In the mines of the North Range, subunits of the Irruptive, going from hanging wall to footwall , include felsic norite, dark norite and dark norite breccia. The footwall complex at Strathcona includes the late granite breccia, which hosts a large proportion of the nickel-copper ores, and a compositionally variable group of brecciated and migmatized rocks, herein referred to as the feldspathic gneiss complex. It is within this latter group of rocks that the vein system of the Copper Zone occurs."

Jan 1, 1981

By Robert White

?Introduction of BMS?Paste fill generalities?Development through paste?Development through rock fill?Conclusion ?Brunswick mine is operated by Xstrata. The mine has been in operation since 1964 and produces around 10 000 tons per day of ore containing (in order) zinc, lead and silver? The ore body consists of close to ten sub-parallel massive sulfide lenses. The length of the ore body is 1200 m with a width of up to 200 m. From the surface, the ore body extends to a depth to 1200m ?There is 100 km of active drifts for a total 400 km ?The mine is divided by 7 levels and 23 actives sub levels

Feb 1, 2008

By P. Mottahed, E. K. S. Passaris, J. Q. Ran

"The jointed roof of underground mine openings in stratified rock can be analyzed in terms of a voussoir beam. Because of the essential indeterminacy of the structure, previous attempts of theoretically solving the equilibrium equation have been unsuccessful. Numericalanalysisby the finite element method taking the geometrical and joint non-linearity into consideration combined with the experimental method has been adopted to study the performance isopara of the voussoir beam. Deformation and failure mechanism is analyzed in relation to the failure modes. Equations are proposed to estimate the elastic buckling strength and the crushing strength of the voussoir beam and to verify the failure mode of shear sliding. For application of the mechanism of the voussoir beam in mining operations, methods are described to predict the stability of a jointed roof and to design the dimensions of mining openings.IntroductionThe roof stability of an underground mine opening has direct effects on the selection of support methods, opening dimensions and, more importantly, on the safety of mining personnel. The prediction of the roof stability can be of importance in the design of a mining method and in mining operations. The jointed roof of mine openings in stratified rock can be stable under transverse load depending on the roof geometry and properties of the roof material and joints. The stability of this type of roof can be analyzed in terms of a voussoir beam which was introduced by Evans (1941) to study the strength of underground strata. Brady and Brown (1985) analyzed the voussoir beam and suggested that the mechanism of the voussoir beam could be used in the design of underground mine openings in stratified rock instead of the traditional continuous beam theory."

Jan 1, 1993

By J. Bigu, M. G. Grenier

"Dust size distribution and aerosol size distribution measurements have been carried out in several Canadian underground uranium mines. In addition, dust samples have been analyzed for long-lived radioactive products of the U-238 and Th-232 natural decay chains using ex-spectroscopy and -y-spectroscopy techniques.From the data collected one may summarize: (a) most airborne particulates are of size below I u-m and 50% by mass are found above 1 u-m; (b) dust clouds are bimodal; (c) preferential deposition of radon (thoron) daughters takes place on airborne particulates in the sub -micron range at about 0.1 u-m; (d) deposition of radon (thoron) daughters is proportional to particle surface area; and (e) ex-spectroscopy and -y-spectroscopy of dust samples reveals the presence of U-238, Ra-226 and some of their short-lived and long-lived decay products.IntroductionExtended inhalation of airborne radioisotopes poses a potential health problem to occupational workers. Because of this, monitoring of radiation and dust levels for dose exposure calculation purposes is not only recommended but in most cases mandatory.CANMET (Energy, Mines a nd Resources Canada) has long since been engaged in a comprehensive monitoring program aimed at determining dust concentrations in the respirable size range, aerosol concentration in the sub-micron range, and in the radioactivity associated with these particulates in underground uranium mines. Measurements have been carried-out with gravimetric dust samplers, dust size selectors (including a horizontal elutriator , a fineparticle spectrometer and Nuclepore* filters of different pore sizes) and a condensation nucleus counter(1 – 6). Inactive and active working sites have been monitored according to some typical mining operations. A summary of these data has been given elsewhere(3- 5)."

Jan 1, 1984

By C. J. Simensen, R. Østhus, H. J. Roven, K. G. Skorpen, H. Kalager

"This work encompasses co-extrusion of alloy Al4.5Mg at the core and rapidly solidified Al4.5Mg1Ag forming the surface layer. The goal is to produce a multi-material by co-extrusion having a relatively hard surface as compared to a softer core. At the same time, work hardening in both alloys is expected to be significant due to Mg in solid solution. Precipitation hardening at 160°C is studied by applying solution heat treatments at 560°C. The hardness increased from 80 to 130 VH in the surface material after 236 h. Surprisingly, the Al4.5Mg alloy also shows pronounced aging at this temperature, i.e. from 70 to 90 VH. The relatively high solution heat treatment temperature introduces grain growth in the core, but this is insignificant for the RS surface alloy. Blisters forms at the surface and cracks follows large portions of the interface. However, the tensile ductility is significant in all conditions due to very pronounced work hardening, i.e. for the as co-extruded, T6, under- and over-aged. The elongation at fracture ranges between 40–45% and the tensile strengths 240–275 MPa. The tensile properties increase linearly with the thickness of the RS alloy, i.e. following the rule of mixtures.INTRODUCTION Al-Mg alloys in 5xxx-series are classified as non-heat treatable wrought alloys (Polmear, StJohn, Nie, & Ma, 2017). The formation of the binary ß-Al8Mg5 does not give a substantial increase in the strength of the alloys (Mondolfo, 1976). When a third element like Ag, Cu or Zn are added, G.P.?zones are formed at low temperatures and intermediate, partial coherent phases are nucleated somewhat higher temperatures and finally a ternary, equilibrium phase is formed (Auld, 1968; Cousland & Tate, 1986; Mondolfo, 1976). Both the formation of G.P.?zones and intermediate phases increase the hardness and strength of the materials. An intermediate, hexagonal T´?phase is formed in Al-5 wt%Mg-1wt%Ag, and finally the equilibrium, cubic phase (Al,Ag)9Mg5 is nucleated (Cousland & Tate, 1986; Mondolfo, 1976)."

Jan 1, 2018

By Stewart A. Ferguson

Location.-The property consists of eight claims (P-12339 to 12343, 12403 to 12405) in Robb township, adjoining Jamieson township on the west. A mocor road extends twenty-two miles northwest from Timmins to the mine. Acknowledgments.- The field work was done in 1940 and 1943, while the writer was employed by the Ontario Department of Mines. The Metals Reserve Company has made available information regarding the property through Messrs. W. R, Dunbar, of Hollinger Consolidated Gold Mines, and W. C. Ringsleben, of the Metals Control Board, Department of Munitions and Supply.

Jan 1, 1945

By R. A. Rabnett, G. Paget, Patrick Walsh

"Tumbler Ridge, Canada's newest resource community, has been developed differently than have been other resource communities.Since its conceptualization, emphasis has been placed on the establishment of a traditional municipal government at early a stage as possible.Planning f or the community goes back to 1977. By then, extensive study by provincial agencies had shown a new resource town would be required to exploit north east coal. The Ministry of Municipal Affairs, in conjunction with a consultant named R.A. Rabnett began the extensive Tumbler Ridge conceptual plan.The results of the conceptual plan are evident in the organizational and planning goals of Tumbler Ridge. In every aspect from the election of officials to some financial matters, the town functions as a normal municipality. With the resource companies of the North East Coal Development within its municipal boundaries. Tumbler Ridge has been able to debenture its capital projects against its municipal tax base.The town's ability to function as a normal municipality is enhanced by its control over Crown land it has purchased from the province. This gives it further control over the development of the community and helps in establishing agreements with the resource companies and the provincial government to ensure that housing and service needs are met. While resource company representatives sit on certain municipal committees, their roles are advisory in nature.The community continues to move toward full municipal status and will have a fully elected Council by 1986.BackgroundPlanning for the development of northeast British Columbia coal resources began in 1976 under the aegis of the provincial Cabinet Committee on Coal Development. A series of subcommittees were established including a Townsite/Community Development subcommittee. The Ministry of Municipal Affairs chaired this subcommittee and continued as the lead agency for the provincial settlement planning effort over the period 1976 to 1981."

Jan 1, 1983

By T. R. Yu, D. B. Counter

"In an effort to increase productivity, the use of fly ash as a binder for consolidated backfill was studied. From laboratory and underground tests f or its cementitious properties and environmental effects, it was found that a portion of Portland cement could be replaced by the same amount of type ""C"" fly ash to produce an acceptable consolidated rockfill product for use at Kidd Creek.The environmental concerns in terms of dust control and emanation of radon gas were unfounded from measurements. The dust count was comparable to the use of Portland cement only, or with ground blast furnace slag, and the radiation readings were low, averaging one-seventh the regulation level.Since May 1984, a total of over 100 000tonnes of fly ash has been consumed as a binder blended with Portland cement, producing over four million tonnes of consolidated rockfill. To date, the fill in the stopes has performed very satisfactorily, while yielding considerable cost savings.IntroductionThe Kidd Creek minesite, located 27 km north of the city centre of Timmins, Ontario, produces 4.5 million tonnes of base metal sulphide ore annually. The mining method for both No. I and No .2 mines is mainly sub-level blasthole stoping with delayed backfilling.No. 1 mine was developed with a shaft to a depth of 930 m in 1973 to recover the ore between the floor of the open pit at the 216 m horizon, and the 792 m horizon. Stopes are normally 18 m wide, 22 m to 65 m long, with heights varying from 90 m to 135 m. Vertical rib pillars between stopes are typically 24 m wide and sill pillars are 30 m thick.Pillar recovery is implemented after the consolidated rockfill placed in the mined stopes has cured for a period of at least three months. This allows a maximum recovery of the ore with a minimum of dilution, while also maintaining safe working conditions.No. 2 mine was developed from a second shaft, sunk to a depth of 1530 m in 1978, for the recovery of ore beneath the No. I mine. Sub-level stoping in No .2 mine is similar to No.1 mine in methodology, yet differs in sequencing, as no rib pillars are left."

Jan 1, 1988

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

By C. P. Verschuren, P. W. Kingston, W. F. Caley

"In recent years, there has been rapid growth in the use of natural stone building and construct ion products. The largest growing markets are for pre-fabricated natural stone panels for interior and exterior wall facing and flooring. This increased demand is attributed to advanced quarrying and processing technologies, renewed appreciation for the aesthetic appeal of natural stone, and to the superior durability of natural stone when compared to glass, steel, and concrete. Geologically, plutonic rocks, and to a lesser extent marble and limestone/dolostone, are used extensively for these applications. This paper details the economic structure of the dimension stone industry, describes the necessary characteristics of a stone quarry, and outlines the geological criteria which favour an economic quarry.INTRODUCTIONThe world building stone industry has remained relatively stable over the last 5 to 6 years. In contrast, the North American stone industry has experienced substantial growth during that period. The increased use of commercial granite is primarily responsible for this growth, where use as exterior wall veneer for commercial, industrial, and institutional buildings represents the largest and fastest growing market.This increased usage in the construction industry has been sparked by the application of new technologies in quarrying, processing and installation , ma king natural stone more competitive with man-made materials which are energy intensive to produce, and have risen dramatically in price. The development of safer, time-saving stone installation techniques has also appealed to the liability-conscience construction industry. Finally, there is a trend by designers and architects toward utilizing long-la sting weather-resistant building materials, and a renewed appreciation of the aesthetic appeal of natural stone. The other large user of granite is the monument industry of North America which, although it has decreased slightly in recent years, still consumes approximately 40% of all commercial granite produced. The local use of commercial marble has remained relatively stable, and North America still relies heavily on European sources and suppliers. There has been some concern over the use of marble for exterior applications in areas subject to acid rain, and in colder climates where the marble ma y be vulnerable to freeze thaw cycles. Despite these concerns, the greatest problem is not with the structural breakdown of marble but the inability of some marbles to retain their polished finishes in the se environments. As a result, there has been an increase in the use of granite at the expense of marble for exterior applications. Finally, commercial marble is used extensively for interior flooring, wall s, counter tops, furniture, sculptures, and stairway components"

Jan 1, 1989

By J. A. Meech, C. A. Harris

"The application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved and because of problems with accurate on stream measurement of process variables. Conventional control is based on proportional, integral and derivative functions of a continuously measured error term. Computer control can enhance these actions by incorporating logical routines to switch from one relationship to another. The success of this logical approach depends on our understanding of the process dynamics and the stability of the process and model under all conditions. Typically the model does not apply at all times in mineral processing because of frequent and unmeasurable changes in the ore parameters.Recent advances in the theory of fuzzy sets have led to the application of this science to process control. Fuzzy Logic can be used to develop heuristic or rule-of-thumb controllers with the strategy based on the actual operating practice of experienced plant operators. Control action has increased flexibility through the adaptation of human reasoning. Acceptance of the control system by operating personnel is significantly higher because of their participation in its formulation. The requirement of an exact model is not essential.A heuristic controller has been designed and tested with a computer simulation model of a secondary crushing plant. The results of this study are discussed and future applications of this control technique to other mineral processes are suggested. IntroductionThe application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved. Mineral processes typically are characterized by non-linear relationships between input and output variables. Many of these variables cannot be monitored accurately on-stream and so long time lags on the measurement loop are features of the system. The processes, themselves, often have long time-varying responses while the process loads fluctuate significantly on a short-term basis.Attempts to control these processes have led to the formulation of mathematical models to describe each unit activity. Adaptive techniques have also been tried to compensate and account for process changes and vageries. These approaches are mathematically rigorous so that their complexity and precision limit their usefulness when applied to ""vague"" processes."

Jan 1, 1987

By V. G. Papangelakis, G. P. Demopoulos

"Recovery of gold from refractory ores and concentrates presently constitutes one of the most important, challenging, and exciting areas of R&D activity in the gold processing industry. New technologies are being tested for the treatment of refractory gold materials, some of which have been advanced to the level of commercial operation. In this paper, some recent technological developments in the hydrometallurgical processing of pyritic matrix-refractory gold ores are highlighted. Key operational steps of each of the alternate hydrometallurgical technologies are analyzed and potential advantages and drawbacks are identified. The processes which are reviewed are: hydro chemical oxidation, biochemical oxidation and pressure oxidation. INTRODUCTIONOver the years the term ""refractory"" has been applied in gold ore processing to denote situations in which straightforward cyanidation failed to yield high gold recoveries. A number of mineralogical and chemical factors may be responsible for this ""refractoriness"" problem. A systematic classification of the different options for their treatment has been discussed in a recent review paper. In this paper, the pretreatment of the submicroscopic gold encapsulated within the matrix of pyrite and arsenopyrite minerals is considered. This type of gold is the ultimate refractory material because complete breakdown by reaction of the host mineral structure is required.The method which has been traditionally applied for the treatment of pyritic-type refractory gold ores is an oxidation roast (single stage or double stage depending on the As content) of a flotation concentrate to produce a porous calcine, the latter being more amenable to cyanidation. Despite its established practice, oxidation roasting is not considered particularly attractive with today's standards for high product recovery and clean environment. Roasting is known to be very sensitive to heating parameters and feed composition and deviation from optimum conditions can result in reduction in permeability which is translated to incomplete gold liberation."

Jan 1, 1989

By R. S. Nichols

"During 1973 to 1978, Canadaka Mines Limited, a subsidiary of St. Joseph Explorations Ltd., undertook an extensive exploration and development program in the Cobalt area. This program resulted in the delineation of previously unknown stratigraphic units in the Archean volcanic sequence. During this time period, significant are controls related to area silver deposits were also identified.The Archean geology is comprised of a volcanic pile conformably overlain by sediments. The volcanics contain at least two felsic volcanic centres near the stratigraphic top of the pile. The bulk of the pile consists of mafic flows and interflow sediments. lnterflow sediments around silver are shoots contain mineralized halos of base metal sulphides. The halos exhibit lateral and vertical metal zoning with Cu, Pb and Zn mineralization decreasing away from an are shoot.Silver mineralization controls determined during the Canadaka program agree with the historically well established importance of Coleman sediments as well as Archean contacts for hosting silver deposits. The vertical extent of are shoots is typically 150to 250ft. A strong correlation was found to exist in the Cobalt area between Archean strike and the strike of are veins. Finally, al/ Cobalt area are deposits appear to be associated with a distinct volcanic pile at the top of a sequence of Archean flows."

Jan 1, 1988

By Rory S. McLaren

"Cost per ton as it relates to mobile underground vehicle maintenance and repair is invariably astronomical. The reason: the mechanic replaced a ten micron filter with a 250 micron filter because it appeared to be physically identical; the purchasing agent bought ""Brand X's"" filter because it was 25% cheaper- the result, a filter life 30% less; the hydraulic pump was sent for repair at a cost of $2000.00 and failed shortly after installation; pumps are failing because there is no testing equipment available in the workshop.This paper will identify a number of the common pitfalls resulting in high costs, and offer solutions to bring these costs to within acceptable limits.The following key issues will be discussed:A. Genuine parts replacement versus ""Brand X""B. Evaluating outside repair shopsC. The influence of environmental conditions on optional equipmentD. Personnel trainingE. Servicing and testing equipmentIntroductionThere is an old English aphorism, ""Look after the pennies, the pounds will look after themselves"".This paper is aimed at the pennies.Genuine Parts Replacement versus ""Brand X""High interest rates and floundering mineral prices are forcing many equipment owners and operators to purchase ""Brand X"" or ""Pirate"" parts in order to survive. ""Pirate"" part manufacturers invariably offer lucrative discounts which are most appealing to the average purchasing agent whose responsibility it is to save money. Unfortunately, in most cases, there is a tradeoff involved; when the price drops so does the quality, which can adversely affect owning and operating costs. Unless totally obvious, ""original"" or ""pirate"" part metamorphosis requires scrupulous analysis by competent individuals.Hydrostatic transmissions have been used successfully for many year s in various industries. They found their way into mobile underground loaders in the early seventies and have since become very unpopular in mining circles due to their apparent ""inherent unreliability"" and near ""prohibitive"" repair costs. The big benefit of the hydrostatic transmission is compact component packaging which enables the machine to work in very small headings."

Jan 1, 1983