Search Documents

By E. L. Day

"In the early 1930s during the course of test work with a simple gold ore, it was evident that the time required to dissolve the gold by cyanidation was very much longer than should have been needed theoretically for the maximum size gold particles in the ore, A similar conclusion appeared to be valid for other gold ores. In a cyanidation system there are many factors which can influence the dissolution rate of gold, and a decision was made to investigate the more obvious variables, because a literature survey at the time showed that with the exception of the work of Yamazarki on the dissolution of silver in cyanide solution, virtually no attention had been given to this subject, Our work was not reported because the intention was to do this on completion of the Study, but owing to the demands on the Section's personnel for other work the investigation was never completed. Although other investigators have since studied the problem, the methods which we adopted and some of the conclusions may be of interest to metallurgists concerned with gold ore treatment.Form of GoldExperiments with gold ores were not possible because of the number of uncontrollable variables present in a gold ore-cyanidation system, therefore pure metal and reagents were used. Initially some experiments were carried out with gold leaf, but it was soon apparent that metal in this form was unsuitable because the uneven thickness of the leaf caused it to break up into pieces and. there was difficulty in determining precisely when complete dissolution had taken place, Numerous factors both expected and unexpected were found to influence considerably the results and much experimental work was necessary to establish the procedures which were finally adopted, Experiments were carried out with gold in the form of foil, wire, rings and sols. Finally, gold foil in the form of cylinders was adopted for most of the experiments although some work with gold in the sol form was included in the programme. Also some experin1ents were carried out with a gold ore to see if effects which were obtained with sodium chloride on gold sols were applicable to gold ores."

Jan 1, 1967

By Feng Tianran, Lu Shijie, Shen Zhengchang, Han Zhibin, Tan Ming

"As a kind of non-metallic material, high-purify quartz sand has been widely used in many fields. Flotation is a popular way to process quartz sand. But it is in difficult position for flotation to get high-purify quartz product due to large amount of coarse particles contained in the feed. In this paper, a design principle of special flotation cell for high-purify quartz sand has been put forward base on ore property analysis and laboratory test, and the pilot scale special flotation cell has been developed to meet the requirement of the quartz sand flotation process. The special flotation cell for high-purify quartz sand is featured by middle positioned impeller, false bottom and draft tube, which could decrease the rising distance of mineralized bubble and strengthen the circulation capacity of the lower part of the flotation cell. Hydrodynamic study indicates that high air dispersion degree and strong lower slurry circulation could be produced by pilot scale special flotation cell, which is helpful to create a suitable hydrodynamic environment for quartz sand processing.INTRODUCTIONNatural quartz is a non-metallic mineral, which is widely used as raw material in multiple industry process (Shifu, 2006). High purity quartz, especially containing more than 99.9% silicon dioxide, is characterized by high temperature resistance, small thermal expansion coefficient, highly insulating and so on. The demand of high purity quartz has been rising along with social and economic development, now high purity quartz is widely used in the field of photovoltaic industry, electronic information, communications and aerospace industry.Quartz is a kind of main rocking-forming minerals in the nature. There are seven genetic types, such as natural crystal, quartz sandstone, quartzite, vein quartz, konilite, natural siliceous sand, granite quartz (Baolei, Shuilin, & Dianchao, 2012). The natural crystal is primarily used as raw material to refine high purity quartz, but it is not available for two reasons. On the one hand, the natural crystal is extremely expensive and poor in resources reserves, which can not satisfy the need of large-scale industrial production. On the other hand, the chemical component of natural crystal is instability, it may lead to low stable product performance in large industrial applications, and it is also difficult to achieve raw materials standardization. Therefore, there are a lot of studies to search for other technological methods to obtain high purity quartz from other genetic quartz types."

Jan 1, 2016

By K. M. Tait, M. M. McDonald

"An overview of the status of the development and application of Integrated Gasification Combined Cycle (IOCC) power generation is presented. Current projects in North America, Europe and Japan are described, together with the status of plans to apply the technology in Canada. A brief review of the technology is presented, including promising coproduction cycles and hybrid gasification fluid bed processes. The ability of the process to be modified for CO2 to be extracted for enhanced oil recovery or disposal is addressed. The environmental impact of IGCC technology is compared to those of other power generation technologies IntroductionDefinition and HistoryIntegrated Gasification Combined Cycle (IGCC) technology is a concept which has been around for about 50 years but has been generating increasing interest in the last 10 to 15 years. This paper focusses on coal as the feedstock for gasification. Other feedstocks used in gasification systems have included oil, biomass, tires and petroleum coke. IGCC technology integrates coal gasification with generation of electricity by means of a combined cycle system which fires the produced gas in the gas turbine. Figure 1 shows the basic components of an IGCC system which are the gasifier, the gas cleanup system and sulphur recovery plant, the gas turbine/generator set, the heat recovery steam generator (HRSG) and the steam turbine/generator set. The benefits of an IGCC system over a conventional Rankine Cycle pulverized coal (RCPC) fired system for the generation of electricity from coal are that the IGCC system has potential to have higher efficiency and lower emissions of NO., SO and CO2 per unit of power produced than the corresponding RCPC system."

Jan 1, 1994

By Zhang Wei

"Pulang Copper Mine is located in Shangri-La county, Diqing Prefecture, Yunnan Province, with currently defined copper reserve of 4.8 million tonnes of copper metal and an average grade of 0.34% Cu. The mineralized zone in a dome shape is 2,300 m long, 600–800 m wide, and 1,000 m high. At present, the project is at a construction phase, with a first-stage mining and processing capacity of 12.5 million tonnes of ore per year. Ore haulage is planned via a drift and ore pass development system. The cavability of mineralized rock is classified into three types (II, III, IV), with type III accounting for more than 98% of the total reserves. The cavability of the orebody is generally considered to be good and block caving mining method is planned. Semi-autogenous grinding and ball milling are adopted for the mineral processing. The tailing dam construction method is a center-line method.INTRODUCTIONAs the China's largest underground nonferrous mine, Pulang Copper Mine is located in the northeast of Shangri-La County, Diqing Prefecture, Yunnan Province, China. It is 62 km northeast of Shangri-La city. Shangri-La County is a Tibetan-dominated, multiple-ethnic region, with a population of approximately 163,000 in 2009. The county is rich in mineral and water resources, thriving with tourism. Its economy is also dominated by agriculture. To date, the defined copper reserves at the Pulang Copper Mine is 4.8 million tonnes of copper metal at an average grade of 0.34% Cu. In addition, it contains a gold reserve of 145 tonnes, a silver reserve of 2,754 tonnes, a molybdenum reserve of 0.19 million tonnes, and a sulphur reserve of 10.5 million tonnes. The first-stage mining and processing capacity is planned at 12.5 million tonnes of ore per year. When it ramps up to this production rate, the mine will produce copper concentrate containing 50,000 tonnes of copper and molybdenum concentrate containing 968 tonnes of molybdenum. A drift and ore pass system is planned for ore haulage and mining method is a block caving method. Semi-autogenous grinding and ball milling are considered for mineral processing. A center line dam is adopted for the tailing dam construction (Feng, 2010; Feng, Li, & Wang, 2011; China Enfi Engineering Corporation, 2014)."

Jan 1, 2016

By Waghmarem Umesh V., Vinay Jain, Pradip, Beena Rai

"The hematite surface plays a vital role in several processes of industrial and technological importance, such as, in beneficiation of iron ores, catalysis, and geochemical processes. Therefore, it is imperative to have a clear description of the structure and composition of this surface, which forms the underlying basis for such a wide variety of complex phenomena. Particularly, from the perspective of beneficiation of Indian alumina-rich iron ore slimes and fines, a clear understanding of the surface structure and composition of hematite surface and its difference from the alumina surface will facilitate identification and/or design of selective reagents which can be used to separate the two minerals. In this work, the hydroxylated hematite (0001) surface was modeled using density functional theory (DFT). The computed planar relaxations are consistent with X-Ray crystal truncation rod diffraction results reported in the literature. It is demonstrated that only one type of surface, that is, the (OH)3-Fe-H3O3-R is stable under aqueous conditions, as the relaxations for the second type of termination: (OH)3-Fe-Fe-R do not match quantitatively with experiments suggesting that its coexistence with the (OH)3-Fe-H3O3-R surface is unlikely. A detailed analysis of this surface shows that two of the three (OH) groups are not connected to the Fe surface atom. Instead, they form H2O molecules by combining with the H-atoms on the O-layer beneath the Fe-terminated surface leaving the Fe surface-atom bonded to only one OH-group. This undercoordination of Fe-atoms on the surface explains its higher reactivity as compared to hydroxylated alumina.INTRODUCTIONThe hematite surface plays a vital role in several processes of industrial and technological importance. A few examples are: flocculation/froth flotation of iron ores (Ravishankar, Pradip & Khosla, 1995), catalysis (Muhler, Schlögl & Ertl, 1992; Samsonov, 1973), and geochemical processes (Brown, Henrich, Casey, Clark, Eggleston & Felmy et al., 1999; Sposito, 1989). Therefore, it is imperative to have a clear description of the structure and composition of the hematite surface, which form the underlying basis for such a wide variety of complex phenomena. Particularly, from the perspective of beneficiation of Indian alumina-rich iron ore slimes and fines, this is an important problem, as a clear understanding of the surface structure and composition of hematite surface and its difference from the alumina surface will facilitate identification and/or design of selective reagents which can be used to separate the two minerals. Our current research focus is at employing molecular modeling techniques to come up with such selective reagents and then test their efficacy in the practical scenario through selective dispersion – flocculation labscale experiments and subsequently plant trials. Obviously, the correct structure and composition of the hydroxylated hematite surface is a fundamental prerequisite for such investigations."

Jan 1, 2016

By Eamonn F. Maher

Superconductivity is one of the most remarkable scientific phenomena ever investigated. It is the phenomenon whereby some materials exhibit zero resistance to the passage of an electric current when cooled to low temperatures, and requires a quantum mechanical explanation. Four Nobel prizes in physics have been awarded specifically on the subject of superconductivity, with many more enabled by superconducting technology. For example, particle beams are generated in accelerators and manipulated in ?particle beam lines? in the ?Big Physics? projects around the world eg. at CERN, Geneva, leading to major discoveries in fundamental particle physics. Similarly, at the JET Propulsion laboratory near Oxford, U.K, controlled nuclear fusion has been demonstrated, and magnetic containment of plasmas is key. In the chemical and biological sciences high field NMR spectroscopy has become indispensable for examining organic matter, revealing the mysteries of the workings of cells, genetics, and in the development of new polymers and pharmaceuticals. With all these very advanced uses for superconducting magnets, it is easy to forget that superconductivity is big business, not just a scientific curiosity. MRI (Magnetic Resonance Imaging) superconducting magnets, the key component of high resolution body scanners, use approximately half of the world?s superconducting wire ? the other half being mostly used in accelerator magnets. The MRI market is about 3 billion dollars per annum, and one MRI magnet uses 200km of wire. New applications for superconducting magnets are now appearing including ?Catheter steering?, enabling much shorter timescales for life-saving brain tumour removals and ?Functional MRI?, a whole new area in patient diagnostics. Whilst the use of low temperature superconductors (LTS) is now well established commercially in superconducting magnets and niche electronic applications, the application of LTS in electric power distribution and transport has been very limited to date. It is now more than fifteen years since the so-called High Temperature Superconductor (HTS) materials were discovered: these can be operated at liquid nitrogen temperatures rather than liquid helium temperatures. However, materials processing and scale-up issues have prevented their widespread use, and in particular the required price/performance criteria are only beginning to be reached except in certain niche markets. BSCCO (Bismuth Strontium Calcium Copper Oxide) tapes up to one km long are now readily available, and have been demonstrated in high current cables for power distribution networks, but the general consensus is that 1) it is difficult to reduce the price much further because of the silver matrix required and 2) in applications where coils are required eg. motors, generators, transformers etc the properties of BSCCO are rather poor because of the critical current dependence on magnetic field. Magnetic fields are always associated with coils and windings, and such fields are of course fundamental to the operation of all electrical machines. YBCO (Yttrium Barium Copper Oxide) however, has good characteristics in field and for the last few years there has been intensive research and development costing several tens of millions of dollars worldwide into the scale-up of production of so-called ?coated conductor?. This ?second generation? tape can be produced by any of many different film deposition techniques, with more or less success for short lengths, but as yet it is unavailable in lengths more than a few tens of metres.

Oct 1, 2003

By I. A. Cameron

In 1979, John Peacey and William (Bill) Davenport published The Iron Blast Furnace Theory and Practice billed as "An up to date and comprehensive treatment of blast furnaces from fundamental principles to modern operations" (back cover). As a 1979 graduate of McGill University’s Metallurgical Engineering program, I belonged to the last "beta" student group which completed the prescribed blast furnace course work before The Iron Blast Furnace Theory and Practice was published. As my career developed, I become an international blast furnace consultant and have worked with blast furnace operators and raw material suppliers on 5 continents. The blast furnace is the dominate iron making process responsible for 70% of global steel production. Blast furnace engineers have implemented many improvements by manipulating the blast furnace process metallurgy using the principles presented by Peacey and Davenport to reduce coke consumption and increase oxygen usage and blast furnace productivity. This paper briefly summarizes some key principles presented by Peacey and Davenport (1979), describes process improvements made by blast furnace operators over the 35 years since The Iron Blast Furnace Theory and Practice was published and outlines important future developments in blast furnace technology.

Jan 1, 2014

By M. Niinae, F. Nakahara, T. Kawamoto, T. Suzuki

"MgO was chosen as an As(V) immobilization agent and a series of immobilization experiments was performed to obtain insights into the behavior of As(V)and MgO during leaching tests. Our experimental and modeling results demonstrated that As(V) immobilization by MgO consists of the following steps: (i) an increase in soil pH, (ii) desorption of As(V) from the soil, and (iii) the re-immobilization of As(V) by MgO/Mg(OH)2particles. Regarding the behavior of MgO, the modeling results showed that when the MgO dosage was 25 mg MgO/4g-drysoilor less, the majority of MgO was used to increase pH, and less than 1% of MgO was used to sorb As(V), which was consistent with the result of leaching tests showing that a high level of As(V) was leached at the MgO dosages. On the other hand, when the MgO dosage was above 25 mg MgO/4g-drysoil, the percentage of MgO used for As(V) sorption increased up to 35%, and correspondingly, the As(V) leaching level decreased to below 0.01 mg/L As at an MgO dosage of 75 mg MgO/4g-drysoil.INTRODUCTIONOne of the major arsenictransport pathways causing groundwater contamination is the migration of arsenicfrom artificially or naturally contaminated surface soils. Therefore, in this study, the immobilization of arsenate (As(V)) in soils was investigated using commercial-grade magnesium oxide (MgO) as a potential cost-effective measurement to prevent the occurrence of groundwater contamination with As(V).With respect to the use of MgO for remediating As(V)-contaminated environmental media, MgO has been used in several studies to remove As(V)from water(Yu et al., 2011; Jia et al., 2013; Tresintsi et al., 2014). Although these studies demonstrated that MgO effectively removes As(V)from water in water-MgO systems, the behavior of As(V)in water-soil-MgO systems has not been evaluated in the literature, and several questions remain to be answered to comprehensively evaluate the use of MgO as an As(V)immobilization agent in soils. For instance, as is well-documented in the literature(Ford, 2002; Lenoble et al., 2002; Zeng et al., 2008), iron oxy-hydroxide (FeOOH) is one of the important adsorbents for As(V)in both natural and engineered systems. Therefore, it is anticipated that the presence of FeOOH in soils significantly influences the behavior of As(V)in water-soil-MgO systems and consequently, the immobilization performance by MgO. Another important question to be answered is the behavior of MgO during the immobilization treatment. In our previous studies (Suzuki et al., 2013a, 2013b), commercial-grade MgO was demonstrated to effectively immobilize lead and fluoride, and the immobilization effectiveness was indicated to last more than 100 years against the exposure to acid rain (pH 4.0). However, these studies focused on the behavior of contaminants. As a result, little is known about the behavior of MgO during the immobilization treatment. The lack of understanding of the behavior of MgO during immobilization treatment is one of the main concerns leading to relatively low public confidence in immobilization treatments."

Jan 1, 2016

By Dieter Birk

"The Atlantic Coal Institute illustrates the potential for high technology employment in Maritime Canada, by using local talent and the latest equipment to address a national market. Since I983, contract research for industry and government has generated 31 man-years of high-tech employment, added $2.3 million to the local economy and contributed new technology for Canadian coal. Industry now has access to new procedures for coal minerals analysis, pyrolysis, and geochemistry applied to industrial problems of exploration, beneficiation, conversion and combustion.Research at the Institute is market-driven, based on cost recoveries from contracts. The financial performance to date exceeds that of similar industrial research institutes in major cities and demonstrates that small isolated laboratories are cost-effective. Economic renewal of Canada's resource industries will require increased R&D which in turn can be a source of local employment and pride. Small research teams are more efficient but require an enlightened policy of contracting-out by big business and big government."

Jan 1, 1987

By B. Panton, J. Carvalho, E. T. Brown

"A major consideration in the design of high capacity tiedown anchors for dam, bridge and tower foundations is the tensile resistance of the rock mass to pullout, typically as a result of overturning moments or hydrostatic uplift. Rock mass pullout capacity for installed anchors is developed from the tensile strength and fracture propagation properties of intact rock, the orientation and physical properties of the discontinuities and anchor confinement at depth. The typically assumed, but generally conservative, design approach is to calculate anchor pullout capacity using the dead weight of a uniformly shaped inverted “cone” with an assumed initiation point and breakout angle. In some cases, some tensile or shear strength is considered across the area of the assumed pullout cone, however, these strength estimates are based primarily on based on limited historic testing data, empirical relationships for rock mass strength developed for other applications, and engineering judgement.As an alternative to the current foundation anchor design method, this paper presents a new approach to the rock cone pullout problem using Discrete Fracture Networks (DFN) combined with numerical simulations. The simulations presented in the paper investigate the influence of fractures in a synthetic rock mass on ultimate anchor strength. In addition, the global influence on fracture network statistics on rock mass pullout failure is also discussed and it is contended that some of the aleatory and epistemic uncertainty inherent in the design of rock anchors can be reduced by considering fracture statistics in anchor design."

Jan 1, 2015

By W. G. Jeffery

"The mining and mineral industries have been, and remain, a major component of the Canadian economy. There are approximately 560 producing mining establishments of which there are some 130 metal mines and an equal number of non-metal mines, the balance being quarries for stone, sand and gravel. For 17 metals and minerals, Canada ranks within the top five as a world producer. There are 29 metallurgical plants. Employment in mining, smelting and refining was about 150000 in 1990. Mineral production, including coal, is about $20 billion. Exports up to the metal stage amount to $15 billion providing a positive trade balance of some $10 billion.The producing industry has a wide diversity of products. The companies range from small single mining operations to large multinationals. In terms of technology the industry has always been in the forefront of cost-effective practice, either using home-grown innovation or freely importing technology from around the world,The Mining Industry Technology Council (MITEC) makes an annual survey of the exploration and R&D expenditures of the senior mining industry that is the mining companies that are involved in mineral production from their existing mines. It does not include those companies solely involved in exploration using funds raised through equity sales.Table 1 shows the actual R&D and exploration expenditures as a per cent of sales. R&D shows a rising trend since 1988although the drop in value of output due to lower prices must be recognized as contributing to the increase. The point about this compilation is that the mining industry re-invests some 4070 of its sales in both exploration and R&D in order to sustain itself. Exploration for the renewal of metal inventories for future mining is a process unique to mining. It is not classified as R&D, and the necessity for this investment goes unrecognized by those who state that the industry does not do enough R&D."

Jan 1, 1993

By Robert W. Plummer

"This paper describes the use of Geographic Information Systems (GIS) as a tool for mineral exploration by using the Eskay Creek area of northern British Columbia as an example. Data entry, analysis and output are discussed. Examples of some of the capabilities of the technology are presented.The main benefit of the technology is being able to perform complex and sophisticated searches of large and diverse data sets to highlight exploration targets. A GIS is a powerful data management tool that can be used in mineral exploration. It is a computer based system that is designed for the collection, storage and analysis of objects and phenomena where geographic location is an important characteristic. The main function of the GIS is to produce information for the geologist from a variety of sources (geology, geophysics, geochemistry, mineral deposits and so forth) quickly and efficiently. This allows the geologist to examine large amounts of data in a fraction of the time than can be done using conventional manual methods."

Jan 1, 1992

By W. F. J. Cosser

AN agreement having been arrived at in 1935 whereby McIntyre Porcupine Mines would purchase gravel for back-filling purposes from Hollinger Consolidated Gold Mines, the aerial gear as described below was installed. As originally discussed, the plan called for installation of a loading bin at the junction to the Hollinger tram, so making the McIntyre tram an entirely separate unit. The experience of the Hollinger engineers, however, went to prove that the operation of a bin (remote from sources of heat) should be avoided if possible, owing to the severe winter conditions (35° to 40° F. below zero).

Jan 1, 1938

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By R. Pakalnis, H. Miller, Madill. T.

"This paper describes a methodical approach to the estimation of the orientation and the magnitude of in-situ stresses. The study was performed at the Ruttan Mine, Sherritt Gordon Mines Ltd. , a 6,000 T.P.D. underground operation, located in northern Manitoba, Canada. It involves an initial estimate to be made based upon: structural interpretation • virgin stress measurements conducted in other areas (world wide, regional)The verification of the prevailing stress regime was made by conducting CSIRO hollow inclusion(1) overcoring measurements. The current cost for a virgin stress determination is about $7000 per measurement(2) and the difficulty encountered in attaining a good reading is high. This paper will describe the analytical procedures employed at Ruttan in evaluating the in-situ stress magnitude and orientation based on three overcore tests. It is proposed to perform an additional six measurements in order to verify the following results:Vertical stress = av (MPa) = 0.027 by depth (m)Major principal stress = o! """" 2.5 xav (340°/-20°)*Intermediate principal stress = a2 - 1.2xav (070°/0°)Minor principal stress = a3 """" o.8xov (160°/-70°)IntroductionThe Ruttan Mine of Sherritt Gordon Mines Ltd., a 6,000 T.P.D. underground operation, is located in northern Manitoba, Canada (Fig. I). The Ruttan copper-zinc orebody is a multi-lensed, steeply dipping (70 degrees) en-echelon deposit. Individual lenses have a maximum strike length of 350 m with widths varying from 7 m to 61 m. The mining method is o pen stoping with delayed backfilling and extends from surface to 860 m below surface."

Jan 1, 1985

By I. H. Warren

"An analysis of form-coking processes is presented in terms-of their fundamental mode of operation and their relationship to other coking processes. Their possible future role in cokemaking is assessed. IntroductionAny consideration of prospects and possibilities for form coking must commence with the iron and steel industries-their likely future growth pattern on a world and regional basis and the potential direction of future developments in iron and steelmaking technology.From the numerous estimates which have been made of the future consumption of steel, it would appear that a growth rate of 3lllo between now and the year 2000 is likely. Radical changes in steel making technology are unlikely to be commercially adopted on any significant scale during the next twenty years . However, widespread commercialization inter alia of continuous casting and direct reduction, growth of electric furnace steelmaking and a decrease in coke rates will all contribute to a growth rate for metallurgical coke that certainly will be less than that of steel."

Jan 1, 1980

By L. Lamothe, C. H. The

"Pilot precipitator tests were conducted at Noranda's Horne Smelter in late 1978 to evaluate methods of improving converter dust collection efficiency. A bout 35 Nms/min. of converter off-gas were isokineticatly diverted from the converter flue to the pilot precipitator leased from Flakt (Canada) Ltd., consisting of three fields, one transformer-rectifier set per field and 77-m2 total collecting plate area. The effects of gas volume flow rate and conditioning the gas with sulphur trioxide and/or additional moisture were tested. II was found that gas flow rate and moisture level had the most pronounced effect on collection efficiency. Based on a techno-economic assessment of different options for improving converter Courell efficiency, waffle hoods and water sprays were installed on the converters to reduce air infiltration and increase the moisture level in the gas.BackgroundThe Horne Smelter of Noranda Inc. is situated in northwestern Quebec and, since the closure o f the min e in 1976, has been operating as a custom smelter. The concentrates treated at the smelter come from various mines with mixed sulphide ores , many o f them containing significant amounts of lead and zinc which makes dust collection in electrostatic precipitators mo re difficult than normal.As part of a continuing program on reducing smelter dust emissions, the No . 6 Cottrell was installed in 1972 up stream of Nos. 2 and 4 Cottrells (in parallel) in a n attempt to improve dust collection by increasing the over- all precipitator capacity ( Fig. I). However, it has never per formed a t its designed efficiency o f 94%. The average efficiency established in various test s was in the range of 60 – 65%."

Jan 1, 1985

By Rachel S. Prudhomme, Michael L. Jeremic

"The consolidation of mine backfill by free zing is a concept which has been under study in the mining engineering laboratories at Laurentian University during the past three years. The proposed underground application of freezing involves the artificial freezing of in-situ backfill by means of a refrigerated brine solution which would be circulated through a circuit off freeze pipes. The most interesting findings to date are: (I) The uniaxial compressive strength off frozen fill is considerably higher than that of cemented fill in a ratio of 20:1 (aggregate to cement), and (2) load deformation characteristics of the frozen fill suggest that a higher ice content results in more brittle failure and that samples which have initially failed can still support up 10 one-half the ultimate load without additional failure.Although at this early stage a derailed economic analysis of the procedure has not been possible, a general evaluation of the costs involved suggests that the method could be competitive with the hydraulic placement of cemented backfill. Results obtained from laboratory investigations indicate that the freezing of backfill is a structurally feasible option .IntroductionGround consolidation by freezing is based on the principle of transformation o f water contained in an aggregate-slurry into ice, which act s as a binding agent between the bulk particles, and which results in the transformation of a granular soil into a ""rock -type"" material. The abrasive nature of the particles enhance s the strength o f the ice by providing internal friction. As a result of this internal friction, the chances of plastic flow of the frozen mass when in a loaded condition are reduced(1). T he strength of a frozen aggregate is al so dependent on the grain shape of the aggregate particles which may or may not promote particle interlocking(2) and on the temperature since, below the freezing point of the water/aggregate mixture, the strength of the frozen mass increase s with decreasing temperatures.In the shaft sinking industry, artificial freezing of loose , unconsolidated soils has been in practice for several decades. Shafts for Saskatchewan 's potash industry have been sun k to depths of 3000 feet by employing artificial freezing to stabilize the Blairmore Formation(3). The common procedure for freezing ground for shaft sinking is summarized as follows(4,5): I) 150 mm diameter bore holes spaced on 1.5 m centres are drilled in a circular pattern with a radius of 1.5 m outside the periphery of the proposed shaft."

Jan 1, 1985

By M. Korchynsky

"The key words which characterize vanadium are: unlimited availability, versatility of applications and price stability. The supply of vanadium is assured by diversified sources, distributed all over the globe. The inexhaustible raw materials base is complemented by a strong vanadium industry. Both the fully integrated vanadium producers and converters of vanadium oxide or vanadium-containing slags or residues guarantee an adequate supply, commensurate with the steady growing demand.The major share of the world's vanadium output is being consumed by the steel industry. As an additive to steel, the versatility of vanadium is particularly impressive. A few hundreds of one per cent of vanadium convert plain carbon steel into high-strength, low-alloy steel with more than double strength. On the other extreme, high-speed steels made via the powder metallurgy route show superior performance with vanadium additions as high as 6 or 8 percent. Vanadium is used as a cost-effective alloying addition in steels for high-temperature service, fully alloyed heat-treatable steels, new dual-phase steels for automotive components, rail steels, etc., to mention only a few applications. Vanadium is also an established essential addition for titanium alloys. The chemical industry is relying on vanadium compounds as important catalysts.In spite of a wide diversity of applications and continual growth in consumption, vanadium has exhibited, over the past several decades, a remarkable price stability, free of conjunctural fluctuations. Because of its availability and versatility, it will continue to be one of the key metallic elements for future technologies.Key Features of VanadiumIn attempting to single out the key features of the metallic element vanadium, three descriptive characteristics come to mind: availability, versatility and price stability."

Jan 1, 1982

By Derek J. Barratt

This paper compares a number of operating conventional and semi-autogenous grinding circuits and analyzes them in regard to operating and capital costs, specifically as applied to porphyry copper ores.

Jan 1, 1979