Search Documents

By S. C. Borah

Graphite, a mineral form of pure carbon, is one of the most versatile minerals in industry, because of its varying physical properties and characteristics. The mineral occurs naturally in the form of tubular crystals or microcrystalline earthy lumps, or it is disseminated in rocks, which have undergone intense metamorphism. India has a large deposition of graphite minerals out of which about 43% are found in Arunachal Pradesh. However, compared to the rest of the country, the North-East Region and particularly Arunachal Pradesh has not attracted attention till date for detail investigation for characterization, beneficiation, prospecting and/or exploitation of the mineral resources including graphite. Bulk graphite sample were collected from upper Subanshiri district of Arunachal Pradesh. Chemical analysis of the representative samples were carried out and found that 7.29%, 19.60% and 6.07% of fixed carbon (FC) is present in graphite sample collected from La-Lamdak, Bopi and Taliha, Arunachal Pradesh, respectively. Chemical analysis of the ash of the graphite sample shows presence of impurities such as silica, Al2O3, Fe2O3, Ca, Mg etc in the graphite sample which are also supported by XRD and SEM-EDX investigation. The graphite samples of Arunachal Pradesh are low grade and do not fulfill the market requirement for the industrial applications. Therefore, low-grade graphite is subjected to beneficiation for the upgradation of the graphite for industrial applications. We have adopted the dispersion?cum-settling technique for the beneficiation of the graphite sample collected from Arunachal Pradesh. The FC of 40.21% with 41.17% raw graphite recovery which is equivalent to 71.02% carbon recovery have been obtained by gravity separation technique using only distilled water without any chemical reagent in case of graphite sample collected from Bopi, Arunachal Pradesh. The graphite sample is upgraded up to 47.75% FC with 41.91% raw graphite recovery, which is equivalent to 85.85% carbon recovery with the pH adjustment at 9 with NaOH. Keywords: graphite, beneficiation, gravity separation, arunachal Pradesh

Sep 1, 2012

By Dianyin Liang, Hongxiang Ran, Xiaoming Wang, Xiaoou Xia

"This paper presents a new magnetic separator, which can be applied to increase the grade of fine magnetite ore feeding of ball mill. This innovative equipment possesses a rotating magnetic system and has a magnetic field of rapid polarity change which can strengthen the destruction of magnetic agglomerations and the dispersion of minerals to improve the quality of separation. Now this type separators have been successfully applied in several large concentrating plants such as Shuichang Iron Mine under Shouang Mining Company in China. Finally, this paper outlines practical results focused on feed grade and tailing yield, the results are showing that the quality of feeding can be improve tremendously. Hence, a new generator of rotating magnetic field has been paved. INTRODUCTION Jidong region in China is the important origin of iron ore, the characteristics of the iron ore in this region is low grade and complex, the iron mine discharges fine powder tailings reaches tens of millions of tons each year, in the wind action easy to form sand, this poses a threat to the atmosphere environment of Beijing. In order to reduce the mixing of large amount of useless ore and reduce the energy consumption of mill operation, a high efficiency pregrinding equipment is needed. Rotating magnetic field separator (RMS) is an advanced equipment, the main advantage of RMS is the significant reduction in particle entrapment and can easily break magnetic agglomeration. This reduction is so significant that RMS is capable of operating very close to theoritical limit for separator precision and can increace efficiency in selection process.Some expenrimental work on dry rotating magnetic field separation has been carried out in July 1998 in the company Ka Pty Ltd, then in 2008 BGRIMM developed industrial separation XCTG0816 in Shandong province . The wet RMS was researched in1960s in Former Soviet Union and the first industrial equipment was developed by BGRIMM in 1970s,then in 1990s wet RMS was applied in Ansteel group corporation. In 2017,6 units large wet RMS (SXCT1230)which were the largest RMS was applied in Sichuan province. No matter wet RMS and dry RMS, although they are used in differenct applications, they have some common research.in addition ,they all have good use effect."

Jan 1, 2018

Most of the Indian coking coals are medium coking and of very high ash content. Beneficiation of these coals is a must for their utilisation in coke making. During washing while the ash content of the coal is reduced, the same is expected to affect the reactive-inert ratio and the proportion of various petrographic constituents in the clean coal. This will affect the coking behaviour, including the expansion characteristics, of such coal. An increase in expansion behaviour of coal increases the wall pressure and may damage the battery wall. Therefore, close monitoring of coking properties along with drop in ash is necessary for smooth use of the coal in coke ovens. An effort is, therefore, essential to understand the impact of washing on its coking properties. The studies were carried out with captive coals of Tata Steel, India. Three medium coking coal samples namely, VII A, VI A and XI SEB seam coals of West Bokaro Colliery were used for the study. The coal samples after washing to different ash levels were subjected to the following analysis: proximate, crucible swelling number (CSN), LT GK test, dilatometer and plastometer tests and petrography. The experimental data were then analysed to assess the relationship of various coking properties of the coal with its ash content. The studies clearly show that there is a strong impact of beneficiation of the coal on its coking behaviour. The impacts are more at lower level of ash in the clean coal. In general, the coking properties increase with a decrease in ash. This is primarily due to an enrichment of vitrinte materials in the clean coal and an increase in the reactive-inert ratio in the coals. However, the most important impact of the lowering ash is on the increase in the swelling nature of the coal. The coals with lower ash become highly expanding in nature. This may be very critical from operations of coke ovens point of view, especially stamp charged coke ovens. Necessary precaution should be taken in selecting the other coal blend constituents when these coals are beneficiated to a very low level of ash content.

Jan 1, 2014

By J. Y. Liu

The comminution in a high-pressure roller mill is modeled by an energy-based population balance approach considering three aspects of breakage taking place in the active zones of the mill: the interparticle breakage in the high-compression zone, the breakage at the edges of the rolls, and the pre-breakage in the acceleration zone. Together with an appropriate model of classification, this model can be used to simulate steady-state performance of closed-circuit grindings with high-pressure roller mill. After a brief description of the basic modeling approach, the algorithm of the steady-state calculation for a generalized grinding-classification circuit is presented, from which the circuit configurations commonly met in industrial practice can be derived. With an iron ore as feed material for example, simulation results are shown and discussed in respect of circulating load, specific energy consumption and product fineness for closed-circuit grindings under various operating conditions. The effects of stressing intensity, working gap, classifier parameters as well as circuit configuration on the overall circuit performance are investigated systematically by means of computer simulation.

Jan 1, 2014

By Ralph J. Holmes, Victor Sharp, Steven J. Spencer, Kevin J. Davey, Jonathan J. Campbell, Peter L. Phillips, David G. Barker

"Improved measurement tools for monitoring and control of AG/SAG mill performance have a high level of interest in industry. Historically, acoustic emission monitoring has been widely used on SAG/AG/ball mills and hydrocyclones to provide new information on the conditions inside these devices affecting their performance. The current work was focused on a new technique using surface vibration monitoring of a number of pilot-scale and production-scale AG/SAG mills to yield insights into the events occurring in the mills. The development of relationships between signal analysis outputs and mill operating conditions can be used for soft-sensor measurement of mill process variables. The technique used an array of accelerometers mounted on the mill lifter bolts linked to a fast data acquisition system which monitored the surface waves generated during operation. Details of the system are presented. Mill operating variables were adjusted systematically to provide a wide range of operating conditions for surface vibration signal collection. The experimental approach is discussed.The signals acquired during the experiments were analysed using a range of techniques. The results show that strong relationships exist between measured vibration power (both total power and within certain frequency bands) and mill load level/power and mill speed. A new method for extraction of power spectral density and band power information on features of interest in a mill rotation cycle is also presented.These results show that single sensor analysis information from the surface vibration system can be used as soft sensor inputs for monitoring process variables such as mill load that until now, have not been reliably measured. System outputs also show considerable promise in the area of condition monitoring. An example of the signal analysis output is presented showing elevated vibration levels in an area with higher resultant wear. Eventually, it is considered that outputs from this system for process variable and wear condition monitoring will be key new inputs to an online AG/SAG mill monitoring and control system."

Jan 1, 2003

By David Verrelli, Melissa Kistner, Leanne Smith, Chris Aldrich, Lidia Auret, Warren Bruckard

In this investigation, different mixtures of realgar and orpiment particles were floated in a laboratory batch flotation cell and multivariate image analysis was used to estimate the arsenic content in the froths. The analysis was based on the froth colour, as well as extraction of three groups of textural features, namely those based on grey level co-occurrence matrices (GLCMs), wavelets and local binary patterns (LBPs). Collectively, these features provided better information on the arsenic content of the froths than any one of the individual groups of features. Partial least squares models could explain approximately 78% of the variance in the arsenic by using all the features combined. The colour content, particularly the green component in the red-green-blue (RGB) features, provided almost as much information as each of the three sets of texture-base features individually.

Jan 1, 2014

By Jury P. Nazarov

"At present the traditional study of crystal lattices of nmerials in a topic “flota tion mineralogy ” is used up. The present investigation is development of the a sclsical approaches to t he analy sis of ideal crystal lattices and f ormation on the basic obtained results of consultation, having practical chara cter.The strategy of develop ment floatation reagents i s offered, which basic pr inciple – complementary assembling m olecules forming surface co mpounds so thatth e steric charact eristic of the “visitor "" (of a polar gro up of molecule SAS) corresponded to the st er ic requirements of the ""o wner"" (elementary cell of a mineral), or coincided inter molecular cavities). In itsh case process of for mation of surface com pounds ca n be considered(a first approximation) as a realization of a principle of the design er "" LEGO "".The approach, which basic idea consi deration actioonf reactant ions and ions of ele mentary cell as three-di mensional objects is developed. And at suchp paroach the laws of a ster eometry - laws describin g spatial effect s are applicable. Thus it is possible toconsider a miner al surface as a mat r ix - basis for formation of the requirem ents to polar group of a molleec cuollector, and or (it is possible) depressant. As a whole approach represents a generalized principle double com plementation, enveloping both power, and geometric asp ects (concept ""lock "" and “key "" - spatial conform ity. Figure 7 (left). Fragment of a crystal lat tice of ap atite. Oleic acid ions interact on ly with th e calcium cations locate d on a long axi s of an elementary c ell. Magenta colour represe nts the calciu m cations, which are n ot particip atin g in interactio n, as th e degree of screening by ions neighbours exceeds 1.Figure 2. (right)The illustration of space complementary. “Afterbuilding” an elementary cell of apatite (radical PO4) related molecules of the visitor – alkyl phosphate (polar group PO4). Cations of calcium are not shown."

Jan 1, 2003

By Yuhe Tang, Jun Zhang, Jianguo Liu

"The nature high carbon graphite with fine particle size has low commercial value because of its narrow application range. In order to improve its value, this paper has studied the methods for nature spherical graphite. The nature spherical graphite can be used as the battery material in the field of electronic product battery and new energy automobile battery, basis on the physicochemical characteristics and particle feature of graphite. In this research, the Fixed Carbon (FC) grade of the graphite sample is more than 95.0% and the particle size of the graphite sample is from +325 mesh to -100 mesh. There are many methods for nature spherical graphite, including the fluidized bed airflow mill, the hydro-spheroidization mill and micropowder mill. The testing results indicate that the method of ACM micropowder mill is the best because the spherical shaping ratio and production yield of spherical graphite are both the best.According to the testing results of the ACM micropowder mill, the best process includes two stages of coarse crushing, four stages of fine crushing and twelve stages of shaping. And two kinds of spherical graphite products can be got, which are the product of D50=22.85 µm and the product of D50=15.43µm, and the whole yield of them is up to 54.43%. So, it lays a foundation for the high value utilization of this kind of graphite resources.INTRODUCTION Graphite is isomer of the diamond. Graphite ore resources are mainly concentrated in China, Brazil, India, followed by Czech, Korea, Mexico, Canada and other countries. Graphite ore has lots of characteristics by itself crystal structure, such as good resistance to high temperature, electrical conductivity, thermal conductivity, thermal shock resistance, good lubricity, plasticity, chemical stability and so on. So, Graphite is widely used in metallurgy, machinery, electrical, chemical, petroleum, nuclear industry, defense industry and other areas. [1,2,3] Natural graphite ore has low geological Fixed Carbon (FC) grade. FC grade should be enriched to more than 94.0% by mineral processing. [1,2] The particle size composition of this high carbon graphite affects its application value. The part of +100 mesh particle size has high application value. The part of -100 mesh particle size has low value because of its limited application field. In order to improve the value of-100 mesh particle size, this part high carbon graphite can be made into spherical graphite. And the value of the spherical graphite is great, it is more than 8 times of the feed. This paper has lots of tests for spherical graphite preparing with the fine particle size natural high carbon graphite. And it lays a foundation for the high value of this kind of resource."

Jan 1, 2018

By Bisweswar Das, Barada Mishra, Hrushikesh Sahoo, Swagat Rath

Banded hematite jasper (BHJ) containing 45.2% Fe, 32.64% SiO2, 0.63 % Al2O3 and 1.25 % LOI is found difficult to beneficiate either by magnetic or flotation techniques due to fine intergrowth of jasper with hematite. Phase transformation by reduction roasting with activated charcoal followed by low intensity magnetic separation to achieve a suitable iron concentrate has been attempted in this study. The mineralogy of the ore and different roasted products has been studied by X-ray powder diffraction (XRD) and scanning electron microscope (SEM) to understand the reduction mechanism. The magnetite formation is observed at 850ºC while metallic iron appeared at a higher temperature. The effects of reduction variables such as reduction time (30-270 min), temperature (750-1050ºC), and reductant (1-12 %) using activated charcoal are studied. An iron concentrate with 64.65% Fe and 55.8% recovery could be obtained under optimum conditions of temperature: 850ºC, time: 1.5 h, and reductant: 6% by weight.

Jan 1, 2014

By Luís Marcelo Tavares, Marko Hilden, Malcolm Powell, Grant Ballantyne, Lian Liu

The t10 relationship developed by Narayanan and Whiten has underpinned a number of the JKMRC models and the characterisation of ore competence through impact testing with the drop weight tester. This usefulness is based on a consistent relationship between the t10 value and the overall size distribution that was noted for brittle rocks. However, like all characterisation tests this should be used only when the controlling conditions apply, which in this case is single impact breakage between two metal platens and within the range of sizes in which fragment sizes are normalizable. For any other mode of breakage the relationship should be confirmed before being applied. Soft ores or bimodal ores with widely different competence between dominant components have non-typical breakage signatures. Breakage via single point impact abrasion, compressed-bed breakage, low-energy surface breakage and incremental breakage, to name some of the other breakage modes, do not obey the general t10 relationship, so their outcomes cannot be used to provide a direct comparison. Inappropriate use of the t10 parameter can result in misleading conclusions about efficiency of energy use. These issues and alternative comparison techniques are presented and discussed in terms of choosing appropriate measures of efficiency of breakage, ore competence and energy required for comminution.

Jan 1, 2014

By D. R. Nagaraj

The traditional (popular) approach to reagent development and optimization, which has become entrenched in both research and practice for many decades, is highly reductionistic, incremental and costly, does not produce robust chemical solutions, and is not sustainable. There are also several other key drivers and changes in the mineral industry that clearly warrant a new approach. In response to these, an intense effort was made at Cytec over the past fifteen years to develop a meaningful, efficient, and sustainable approach to develop new reagents and robust chemical solutions in mineral separations. This effort culminated in three important outcomes: a) development of the holistic approach, called FLOTATION MATRIX 100? process, b) novel reagents, and c) enhanced application knowledge for reagents. In this paper, the efficiency, utility and power of the holistic approach will be demonstrated with examples using both existing and new reagents in the processing of Cu-Au, Au and Cu-Mo ores.

Jan 1, 2014

By V. V. Lvov, L. S. Chitalov

"The purpose of the research is intensification of physico-mechanical ore properties determination for ball grinding processes in comminution circuits. The research presents comparative studies aimed at intensification of Bond Ball Mill Work Index (BWi) determination, such as testing technique of Ahmadi and Shahsavari, Berry and Bruse, Gharehgheshlagh, Horst and Bassarear, Kapur, Magdalinovich. The subject of the research is a test procedure of apatite-nepheline, copper-nickel, gold-sulfide and iron ores for the Bond ball mill index. The Bond Ball Mill Work Index for the material firstly was determined by standard Bond test methodology. Two the most promising testing techniques - Ahmadi and Kapur testing techniques - were modified. For the Ahmadi technique it was proposed to pay attention to the circulating load, which should be stabilized on the value of 250% as fast as possible. Two methods were put forward to quicker stabilize the circulating load. For the Kapur technique it was proposed to use empirical coefficients, which is determined especially for the apatite-nepheline, copper-nickel, gold-sulfide and ores. The modified Ahmadi and Kapur techniques require no more than two cycles of ball grinding to determine BWi (while normally 6-8 cycles are required) and less than 5 kg of initial feed. The suggested modified Ahmadi and Kapur techniques allow to intensify the physico-mechanical ore properties determination for ball grinding processes and BWi test costs considerably, which makes them useful for mass sampling and monitoring strength properties of ores entering a concentrating mill. INTRODUCTION When designing concentrating mills, the choice of the technological scheme for ore pretreatment, particularly the type, quantity and size of the main process environment, the determination of optimal grinding conditions and the calculation of equipment load are carried out by preliminary studies of grinding in semi-industrial or laboratory-scale plants. Semi-industrial tests on full-scale plants provide the most reliable information for calculating specific loads for equipment. However, this requires a significant amount of ore samples, a high labor costs and the pilot plants. Thence the most researchers performed grinding tests with small laboratory equipment using small ore samples."

Jan 1, 2018

By H. Z. Kuyumcu

Associated with the development of a novel microbiological oxidation process for the conditioning of iron hydroxide slurries from ferrous mine waters, there is a realistic chance to make the contained iron available for a material utilization. The transformation of ferrous into ferric compounds is coupled with the precipitation of iron hydroxisulphate mostly in terms of the mineral Schwert-mannite. The further treatment of the iron hydroxisulphate has to be aimed on the processing for product recovery and product refinement. For many potential applications, e.g. in the ceramic industry, the pigment industry or for metallurgical applications, the removal of sulphate is essential. For the dehydration of the iron hydroxisulphate and the sulphate removal, microwave heating technology is a beneficial method. In contrast to conventional thermal heating processes the supply of energy in microwave application takes place directly within the material through the dissipation of electromagnetic energy, i.e. no heating medium is needed. It is a volumetric heating process regardless of the surface of the material. The rapid and targeted energy supply and the good controllability of microwave heating systems are advantages which have led to a wide variety of applications in industrial processes. Among the diverse use for heating of temperature-sensitive, chemical and pharmaceutical products as well as foodstuffs the number of applications also in mineral and solid processing increases. At the Department for Mechanical Process Engineering and Solids Processing of the Technical University Berlin the use of microwave technology for the treatment of iron hydroxisulphates has been investigated systematically within the framework of a cooperative research project. The paper at hand shows results from material conversion tests subject to a variation of the relevant process parameters. The reaction products are characterized and the process is compared with the conventional heating in a rotary kiln.

Jan 1, 2014

By Seoul National University, Ki-Ho Kim, Jong-Pyo Kim, Sung-Min Joo, Hee-Chan Cho, Hyung-Seok Kim

Aragonite was synthesized in addition of Mg2+ ion and SrCO3 seed by carbonation process, and the best condition and mechanism of the synthesis was studied by analysis of continuous pH change, ICP, XRD, and SEM. As MgCl2•6H2O addition increased, aragonite phase increased at condition of CO2 flow rate of 100 mL/min and stirring rate of 250 rpm. It was the dissolution of Mg(OH)2 that determined overall reaction time. As SrCO3 seed addition increased at 0.2 mole MgCl2•6H2O, the amount of aragonite increased and the aspect ratio was from 5 to 9. And it was thought that Mg2+ ion prohibited calcitetransformation of aragonite formed by SrCO3.

Jan 1, 2003

By Johann Botha, Niel de Clerk, Tony B. Lange

"PROCESS COMPLEXITYDespite many years of research and development, mineral and metallurgical processes are in general highly complex and still difficult to understand and control. One of the biggest factors contributing to this complexity is the highly non-linear, multivariate, chaotic nature of such processes.This complexity is magnified in production environments where business optimisation rather than beneficiation is the primary objective. Return on investment, sustainability, and social issues such as Aids and the environment all form part of the goal hierarchy of industrial concerns. In addition, international competition and price volatility all have a huge impact on these processes in terms of operational constraints.Therefore the optimisation and control of beneficiation processes must take into account many factors other than pure process variables such as flow rates and levels. For example, commodity prices and client requirements all need to be added to the control problem, which together with incomplete process knowledge and non-linearities etc., make automation and optimisation extremely difficult.The ideal solution is to have a controller which in addition to performing full non-linear constrained optimal control can at the same time take into account other non-process factors such as price and client satisfaction."

Jan 1, 2003

By Yuexin Han, Zehong Wang, Fujia Yu, Wanzhong Yin, Xinchao Wei

Bauxite is the main raw material in alumina and refractory industries. China has plentiful bauxite resources, most of which belong to the diaspore type bauxite with characteristics of high aluminum content, high silicon content and low ratio of alumina and silica (A/S). The resources with A/S 4-7 account for more than 60% of the total resource reserves of bauxite. Therefore improving the A/S through bauxite desilication is the key task of bauxite concentration in China. Normally the grinding fineness of 80-90% - 0.074mm is required in the bauxite flotation process. Thus fine grinding of bauxite ores is necessary, which leads to the high energy consumption. In the meanwhile, bauxite ores are easy to produce slime during grinding processes. The large amount of slime produced in fine grinding greatly worsens the process environment of bauxite flotation, affects the separation performance and results in the loss of metal. Also, fine grinding makes the flotation concentrate difficult to dewater, while the water content in the flotation concentrate must be removed by distillation in the subsequent alumina dissolution process, causing the increase of energy consumption and cost in the production of alumina. In this study, the selective grinding behaviors were examined with Henan Bauxite as feed. Separation of alumina and silica at a coarser grinding fineness was achieved and new route was explored to enhance the desilication in bauxite concentration to improve the A/S of bauxite concentrate.

Jan 1, 2003

By Nicholas Enraght – Moony, Alvin Johns, Zhonghan Zhang, Zhang Xianhua, T. Choo

"The tungsten (WO3)-rich ores from King Island Scheelite (KIS) Mine, Australia, containing scheelite(CaWO4) were previously recovered by gravity separation and flotation of fine scheelite (1978-92) with an overall recovery of 76% when both circuits were operating. Recently extensive test work has been conducted both in China and in Australia on KIS ores, assaying from 0.50%-1.34%WO3, and tailings assaying 0.2%WO3(GZRINM 2009; 2011a; 2011b). A new approach, which aimed at improving both recovery and grade of concentrate by means of an innovative all flotation route WOF (Whole Ore Flotation), achieved excellent results: 90%-92% recovery to concentrate grade of 66%-70%WO3for the ores. The process is characterized by the use of selective reagents in flotation, including a newly developed collector for scheelite, GYWA. The WOF process also embraces the "Improved Petrov Method" in the cleaning of scheelite rougher concentrate. Earlier investigations found that the removal of sulfides by flotation prior to scheelite flotation was not necessary. It was also found that recycling of process water did not influenceresults. Two main ore types were tested as well as tailings from 2009to 2001(0.20%WO3). In addition a flow sheet using wet high gradient magnetic separation (WHGMS) in tandem with flotation was also investigated for the tailings."

Jan 1, 2014

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By S. M. Javad Koleini

Processing of phosphate ore sample was investigated for increasing phosphate content and reduction of its gangue minerals such as carbonates and silicates. Experimental designs were per-formed using Taguchi method. Different flotation methods were investigated for Moundon phosphate ore sample and three methods were used as follow: direct cellophane flotation, reverse calcite flotation and reverse quartz flotation. Because of the sensitivity of cellophane flotation to slime content, prior desliming was carried out before the experiments. Direct flotation experiments carried out and a concentrate contained 23.80% P2O5, 6.88% SiO2 and 72.33% recovery were produced. The achieved P2O5 content in the produced concentrate from reverse flotation of calcite was 26.44% and the recovery was 82.56%. The concentrate products obtained at optimum conditions by direct flotation of phosphate and indirect flotation of calcite were subjected to indirect flotation of calcite and direct flotation of appetite and final concentrates with P2O5 grade of the order of 24.19% and 26.96% were obtained, respectively. It was concluded that one stage direct flotation is unavoidable to achieve a product with low SiO2 content.

Jan 1, 2014