Search Documents

By Avishan Atrafi, Marek Pawlik

"Gas dispersion properties of sodium salts of 6, 12 and 18-carbon fatty acids (hexanoic, lauric and oleic acid) were investigated as a function of pH. A strong effect of pH was observed on gas dispersion properties of fatty acids. At high pH for 12 and 18 carbon fatty acids, at which these surfactants formed a true solution, the gas dispersion properties were similar to those of MIBC. In the case of sodium hexanoate, which has a much higher solubility than the longer chain fatty acids and therefore does not form precipitates, the gas dispersion properties of this surfactant were strongly enhanced in the acidic pH range, where hexanoic acid was fully associated. This result is an indication that undissociated hexanoic acid is much more surface-active than anionic hexanoate. Only a small effect of the surfactant chain length on gas dispersion properties of the tested reagents was observed. The measured critical coalescence concentration (CCC95) values increase slightly by decreasing chain length and range from 5.8 x 10-5 mol/L (17.7 mg/L) for sodium oleate to 7.2 x 10-5 mol/L (16 mg/L) for sodium laurate at pH 10 and 1.9 x 10-4 mol/L (26 mg/L) for sodium hexanoate at pH 3.7. These are compared to CCC95 of MIBC, which is measured to be 8 x 10-5 mol/L (8 mg/L). The soluble molecular species were recognized as the most effective species in preventing bubble coalescence."

Jan 1, 2014

By Z. L. Huang

A new porous apatite product was prepared using phosphorite from Yichang China by a tem-plate-directed method in self-made reaction equipment under constant temperature and pressure. The product was characterized by XRD, FT-IR and SEM. The results showed that the product was a kind of micrometer porous sphere three-dimensionally structured by apatite nanoflakes, that the average thickness of nanoflakes was about 50 nm, that the average pore size was about 1.2 µm and that the particle average size was about 20 µm. Great amounts of Ca2+channel, high special surface area and regular spherical shape show the potential promising applications of this special porous apatite product in the fields of catalyst, medication, chemical engineering and environment engineering

Jan 1, 2014

By Sydney Mantsho, Toni Streczynski, Manuel Gonzalez

"In 2013, the commissioning of the MillStar Stabilisation and FloatStar Stabilisation and Optimisation controllers were completed at the Cerro Bayo Silver (Ag) mine in Patagonia, Chile. The MillStar control system has stabilised the feed to the SAG mill as well as the density at the discharge end of the SAG mill and ball mill. The FloatStar Stabilisation and Optimisation controllers have successfully stabilised and optimised the flotation circuit to ensure consistent product quality within desired specifications.The mill feed is controlled utilising the MillStar Solids Feed controller. Additionally, the solids to liquid ratio into the SAG mill was controlled utilising the Mill Inlet Ratio controller in conjunction with the Solids Feed controller. The discharge end of the milling process is a highly interactive and complex system. The use of a Robust Nonlinear Model Predicative Controller (RNMPC) was ideally suited to control this section of the process. On the Cerro Bayo milling circuit, the RNMPC was used to control the mill discharge sump level and the primary cyclone feed density to produce a more consistent feed to the flotation circuit.Three levels of the FloatStar control system were installed, for flotation stability, concentrate flow stability as well as grade optimisation. The Level Stabiliser was used to stabilise the level control on 6 flotation banks. The Flow Optimiser was commissioned on the Rougher, Scavenger and Cleaner concentrate sumps to stabilise concentrate flow from the flotation cells. The Grade Recovery Optimiser was commissioned on the Roughers section. A number of instrumentation challenges were identified which limited the overall benefit derived from the system. Once these were addressed, the performance was optimised. The overall benefit provided by the system was observed in terms of the improvements in Ag recovery."

Jan 1, 2014

By Carmina Quintanar, Mario Palominos

"The mining industry is currently facing significant challenges to identify and adopt sustainable collector chemistry that effectively recover value minerals in difficult-to-process low-grade resources. These are typically characterized by complex mineralogy and the presence of significant amounts of penalty gangue sulfide minerals, especially pyrit which is a challenge to separate from value minerals at many major mine operations. Three chemical strategies for dealing with gangue sulfides and penalty elements are: a) selective flotation of value minerals while rejecting penalty minerals in the whole circuit, b) rejecting penalty minerals in an appropriate part of the circuit using selective depressants, c) using a combination of selective collectors and depressants in appropriate parts of the circuit. This paper will evaluate different strategies for dealing with those penalty elements and propose the most efficient alternative. New products and application technologies have been developed in the past 25 years by Cytec for implementing these strategies as dictated by the particular needs of a given plant. However, in recognition of the growing interest in meeting the sustainability challenges, Cytec Research and Development have been focused in the development of greener products (collectors, modifiers and frothers) and processes using FLOTATION MATRIX 100TM approach used to develop the optimal collector system for each specific ore. An overview of these new developments is given in this paper using case studies of application of selective collectors and polymeric modifiers including the newer, greener chemistries."

Jan 1, 2014

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"In this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 - 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 - 3.0x103 mol/m3 NH4OH, 0.4 - 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration.For gold recovery from the pregnant solution, the trioctylmethyl ammonium chloride (TOMAC) was used in this investigation as an extractant to extract gold from thiosulfate solution without pH and other adjustments. The effects of gold concentration, pH, ammonia, thiosulfate and cupric ionic concentrations, extractant and diluent concentrations and retention time on the gold recovery were investigated. It was found that 180 mol/m3 extractant diluted with n-octant at O/A ratio of 1:1 could extracted the 100% of gold in 0.6 ks from the thiosulfate solution at the optimal leaching conditions. The 100% gold stripping could be achieved with 10% thiourea solution."

Jan 1, 2003

By J. A. Sweet

The issues facing graduate training in the mineral processing industry are not too different today from those that prompted the initiation of the Anglo American Platinum Graduate Development Programme (AGDP) in 2002. Graduate metallurgists in South Africa enter the industry from different undergraduate programmes at various tertiary institutions, and so the knowledge and skills of the young graduates varies. Further, the geographical expansion of the industry combined with the downsizing of business units means that there are fewer opportunities for young graduates to be mentored through their first few years on site. Anglo American Platinum chose to address these issues by implementing an intensive, structured graduate training programme for all their new metallurgical graduates, known as the AGDP. The first two years of experience of the AGDP, from the viewpoints of both graduates and lecturers, were presented to the mineral processing community at the IMPC in Turkey in 2006 (Sweet et al, 2006). From the beginning, the programme was structured in a modular fashion to include a basic technical ?toolbox? including statistics, the scientific method and sampling protocols, while the mineral processing content comprised advanced learning in comminution, classification and flotation (later extended to include hydrometallurgy). Technical communication ? both written and verbal ? was included from the start. The programme was focussed very strongly on site work (?learning by doing?), with a major integrated site campaign conducted and analysed by each cohort. In 2012 the AGDP will accept its ninth cohort into the programme. This paper describes how Anglo American Platinum and the University of Cape Town have developed and adapted the programme over the last few years, in response to the challenges of the global recession, skills retention, and the changing operational needs of the company. The programme, which was drawn up to accommodate around 15 concentrator-only graduates, now accommodates 35-40 concentrator, smelter and refinery graduates annually. The programme has also been modified to facilitate new graduates spending most of their first year on the operations. The benefits of the programme for Anglo American Platinum have been tangible, and will be discussed in the paper. Keywords: graduate training, technology transfer

Sep 1, 2012

By S. K. Kawatra, T. C. Eisele

"Coal-fired electrical power generation plants produce 56% of all the electricity in the U.S., burning approximately 860 million tons of coal annually. This results in the production of 58 million tons of fly-ash; 19 million tons of bottom ash and boiler slag, and 23 million tons of desulfurization sludge.s annually. These are a considerable disposal problem, and it would therefore be very valuable to be able to sell these residues and by-products as useful materials, rather than paying to dispose of them in landfills. However, utilization rates are currently very low, below 32% even for the most thoroughly commercialized combustion byproduct (fly-ash). This poor utilization rate is a result of the high impurity content of combustion byproducts, which makes them unsuitable for existing markets.Mineral processing techniques are useful for upgrading and utilizing combustion by-products. Fly-ash can be processed to remove unburned carbon, or utilized as a binder component in ore pelletization and agglomeration processes; bottom ash can be processed to produce certain aggregate grades; CO2 emissions can be sequestered using modified leaching techniques; and many scrubber sludge’s require processing before they can be used for producing gypsum products.The experiments described in this paper were carried out to study the application of mineral processing techniques to upgrading combustion by-products, particularly flue-gas scrubber sludge. A process was developed for upgrading unoxidized Flue-Gas Desulfurization (FGD) sludge’s by removing the primary impurity (unreacted limestone). A combination of hydrocycloning followed by froth flotation reduced the limestone concentration to as little as 1.7%, while recovering 66% of the sludge weight as a clean product. The recovered limestone was sufficiently concentrated that it could be recycled to the scrubber for more complete utilization."

Jan 1, 2003

By Z. C. Zhen

Basing on character of fine ores, and employing all the advantage of dissolved-air flotation, the study within the dissertation put forth the methods of superfine metal mineral flotation with dissolved-air flotation equipment, and constructed a full set of laboratory flotation system. Experiments both in water and in slurry were respectively carried out by means of this flotation equipment. Further study was also fulfilled on mechanism of air-dissolved released devices, and the key components of system including ejector, releaser and saturator were designed. Optimizing devices parameters were chosen by taking ideal performance of the devices into consideration, according to orthogonal experiments and tests on bubbles factors, those performance factors were called air release rate, air release efficiency. The results with some minerals are better than JJF flotation machine with 30 litres bulk. The Dissolved-air Flotation(DAF) machine shows great potentiality in treating super-fine metal mineral concentration. The research indicates the Dissolved-air Flotation(DAF) system has superiority over mechanical flotation machine in fine flotation. Air-dissolved released bubbles appear on the surface of hydrophobic minerals in priority, solving collision probability less in the tradition fine mineral separation, such that the metallurgy technology of fine metallic minerals are improved. The exploratory research is a foundation for industrial pilot, commercial test and equipment maturity in the future.

Jan 1, 2014

By John Starkey

"The development of the Minnovex SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.In the last century, it was deemed prudent to select up to 50-tonne samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5-tonne sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50-tonne sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By Sunil K. Tripathy

Particle characteristics such as size, density, liberation and magnetic susceptibility play vital role in magnetic separation technique. To understand the performance of magnetic separation process for chromite beneficiation industry, particle characteristics need to be analysed. However, to date, this has been an expensive and time consuming task, thus only minimal amounts of this type of data are available in the literature. Several new methods are being developed, that will produce the required mineralogical and liberation data to provide processing information rapidly and inexpensively. Among these, QEMSCAN is a unique and advanced characterisation equipment used for liberation analysis for different ore whereas S.G. Franz Isodynamic Separator for determining the magnetic susceptibility. In Indian chromite deposits, the content of iron bearing minerals in the ore is typical which controls the Cr:Fe ratio in the product while treating in gravity based beneficiation plant. In the present investigation, detailed characterisation of two distinct chromite ore samples from Sukinda chromite deposit, India, was investigated which includes advanced mineral characterisation using QEMSCANand magnetic susceptibility measurement by using Frantz Isodynamic separator, etc.. Presence of haematite and gibbsite along with chromite mineral were identified as major gangue minerals in the high grade ore from XRD pattern whereas Goethite, Quartz, Haematite, Kaolinite, Ringwoodite identified in the low grade ore. The mass magnetic susceptibility of low grade ore is very high 5.2 cm3/g compared to 2.7 cm3/g for high grade ore, due to the presence of abundant quantity of iron bearing minerals. Subsequently, these two types of ore were subjected for magnetic separation for improving Cr:Fe ratio by using different magnetic separators viz. induced roll magnetic separator, wet high intensity magnetic separator, rare earth roll magnetic separator, rare earth drum magnetic separator. The results of magnetic separation studies indicated that, Cr: Fe ratio of the chromite ores can be improved to 3.99 and 1.97 from the feed assaying 3.09 and 1.29 respectively. Studies on rare earth roll magnetic separator indicated that both the ores were upgraded to a maximum Cr:Fe ratio level at optimised condition. Keywords: characterization, QEMSCAN, magnetic separation, rare earth roll magnetic separator, industrial mineral, chromite

Sep 1, 2012

By J. Y. Tian

In view of the fact that many domestic iron ore-dressing plant applying flotation cells in the re-verse flotation, to improve the technical level of magnetite reverse flotation, we apply such a technological process of one stage rougher and two stages scavenger flotation column respectively. The middling from the two stage scavenger process are returned to magnetic separation for condensing. By contrast, the technological process of one stage rougher and one stage cleaning flotation cells is made up of by multi-magnetic separation and magnetic middling regrinding separations. It has been proved that the flotation column we offer can simplify the technological process structure, obtain advanced technical indexes, run the system smoothly, reduce energy consumption, and be environ-mental friendly.

Jan 1, 2014

By Peng Qian, Xiao Li, Guoyan Fu, Peiwei Han, Yongliang Wang, Shufeng Ye

"Arsenic removal from high arsenic gold concentrate is conducive to increase the mineral value and realize the mineral comprehensive utilization. This study investigated the alkaline pressure oxidation leaching (APOL) of an arsenical gold concentrate in lower temperature to separate the arsenic into filtrate. The effects of temperature, NaOH concentration, solid-liquid ratio, reaction pressure and stirring speed on the leaching efficiency were investigated, and the characteristics of the gold concentrate and leaching residues were evaluated using XRD and SEM analysis methods. The obtained results showed that by using lower temperature (<60?) it is possible to avoid the production of elemental sulfur during the leaching process, which is benefit for the oxidation of arsenopyrite; When the reaction was carried out under appropriate conditions, more than 98% of the arsenic will be extracted into the filtrate as the form of arsenate or thioarsenate. INTRODUCTION In recent years, there has been considerable interest in the recovery of gold from refractory arsenical gold ore. The arsenic in this kind of ore usually exists as the form of arsenopyrite, and the gold surrounded by arsenopyrite exists as the form of fine particles, which will give many difficulties to metallurgical work. When the content of arsenic in the gold ore is more than 0.5%, it will seriously penalize the smelting efficiency (Ruiz et al., 2014). So pretreatment of the refractory gold ore is necessary to obtain the largest economic value and environmental benefits (Balaz et al., 2000). The oxidation pretreatment processes mainly include roasting oxidation, pressure oxidation, chemical treatment and biological treatment (Ann et al., 1992; Kou and Chen, 2012; Tongamp et al., 2010; Fernandez et al., 1995; Lin and Zheng, 1996). Among them, the roasting oxidation and pressure oxidation are the more ordinary processes in industry. The roasting oxidation process is the mature and adaptable technology, but the production of waste gas containing sulfur and arsenic will pollute the environment. The pressure oxidation method possesses certain metallurgical and environmental advantages, and can efficiently decompose the mineral. According to the different solution media, the pretreatment can be divided into alkaline and acidic pressure leaching pretreatments (Papangelakis and Demopoulos, 1990; Hiskey and Sanchez, 1995). The acidic pressure oxidation method has been used in most smelting plants for high arsenic gold ore pretreatment, while the alkaline pressure oxidation is still not widely applied. Compared with the acidic pressure oxidation, the alkaline pressure oxidation can be realized under lower temperatures."

Jan 1, 2018

By Grant C. Lukey, Jannie S. J. van Deventer

"The environmental effects of the mining and mineral industry include destruction of natural habitats, changes in river regimes and water tables, and other serious ecological impacts. In this century, it is likely that water will become a critical resource, and in most countries the mining industry competes for a share of this resource. The Kyoto Protocol may at first seem only relevant to the coal mining and power industry, however, it should not be forgotten that the mining and mineral industry is a significant consumer of power. Therefore the ratification of the Kyoto Protocol by most developed countries and the introduction of a carbon credit trading scheme will impact on the industry by potentially increased costs in utilities and waste discharges. It is clear therefore that the mining industry faces many challenges in the coming years. The mining industry?s commitment to sustainable development needs to continue to evolve, in order to meet these challenges effectively. With the advent of globalisation of the industry, it is now an opportune time for the industry to gain international agreement on how they want the industry to achieve sustainability in future years; such a progressive approach is necessary, otherwise government will force the industry to change, which may not necessarily be the best outcome for the industry.INTRODUCTIONThe Earth Summit in Rio de Janeiro in 1992 was an opportunity for world leaders to assemble and discuss strategies and initiatives that provide for further industrial growth without adverse effects on the environment. The World Summit on Sustainable Development held last year in Johannesburg, South Africa, was an opportunity to evaluate those initiatives implemented over the past 10 years, and to set a new and sustainable direction for the future. It is clear that industrial and technology development will continue at a rapid pace in order to serve the needs of a growing world population, but it is essential that the course of this development is well planned, well executed, and that it is sustainable. In reality, while government officials and politicians continue to debate policy and international protocols, the environment continues to suffer and the effects of climate change and global-warming become more real each day."

Jan 1, 2003

By Lj. D. Andric

Development of modern devices for mechanical and mechanochemical materials activation has been dated since the beginning of last century. Rapid development of high-energy mills that are different in type, size, design and performances, has been occurred during the last four decades. Because of complete understanding of mechanical processing, entire knowledge of theoretical principles of high-energy mills is necessary. These principles are main causales of process that are happened in materials during the mechanical activation. This paper is occupied by theoretical principles of operation of high-energy mills. Conventional high energy mills with balls, high-energy planetary mills and high-energy vibrational mills are particularly considered in the paper.

Jan 1, 2014

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin. The Rohm & Haas chelating resin, Amberlite IRC 748, with its weakly acidic groups, did not work in acidic solution but exhibited good results at pH 4 and above. The resin that efficiently removed metals from high acidic solutions was the bis-picolylamine resin. Maximum nickel uptake values ranged between 85 g and 112 g Ni per Kg of resin.The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to- solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment."

Jan 1, 2003

By Zhang Yuejun, Feng Tianran, Shen Zhengchang, Han Dengfeng

"With continuous mining industry development and dressing plant scale expansion, flotation cell is developed towards to large scale and intelligence. Based on flotation cell scale-up theory and industrial practice, KYF-320 air-forced mechanical flotation cell with effective volume of 320m3 was successfully developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM) and adopted by China Gold Inner Mongolia Mining Co., Ltd, Luming project of China Railway Resource Group Co., Ltd, and Toromocho project of Chinalco in Peru. In this paper, the structure and technical characteristics of KYF-320 flotation cell are introduced, and the application of that equipment in China Gold Inner Mongolia Mining Co., LTD is demonstrated. The tank of KYF-320 flotation cell is cylinder-shaped, 8200mm in diameter and 7500mm high, with double froth lauders and large inclined angle cone bottom. 16 sets of KYF-320 flotation cells of which the processing capacity is 26,000,000 tons/a, are used in the second phase project of China Gold Inner Mongolia Mining Co., LTD. Their stable running shows the long life of impeller and stator and the power intensity (power consumption divided by effective volume of flotation cell) of KYF-320 flotation cell is only 0.73kW/m3 which is significantly less than that of small scale flotation cells. The industrial production obtains good results that the Cu grade of final concentrate of entire flotation circuit is 22.90% at the recovery of 86.73%, when Cu grade of feed is 0.35%, which indicates that KYF-320 flotation cell has good performance and can be widely used in large scale mine."

Jan 1, 2014

By K. S. McClure, S. B. Chitralekha, R. B. Gopaluni, Chmylek. T., S. L. Shah

This is a tutorial paper on industrially successful approaches for nonlinear process monitoring. Online process monitoring is essential to continuous operation of plants at high efficiency. The problem of process monitoring is one where an impending but undesirable process condition has to be identified and used to alert process engineers. This problem has traditionally been solved by practicing engineers using statistical techniques that detect a change in the underlying correlation structure of process variables. For linear correlation structures, algorithms such as principal components analysis, independent component analysis and partial least squares have been proposed. However, many industrial processes exhibit nonlinear correlation structure between the process variables. In this tutorial we describe various nonlinear monitoring techniques and elaborate on two recently developed methods, namely Support Vector Machine and Local Linear Embedding. The two methods are evaluated by application on two experimental case studies, a SAG mill and a polymer extruder.

Jan 1, 2014

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis shows that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. Co-existence of ilmenite with pseudorutile, rutile and haematite is observed in substantially varying amounts in the three deposits. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among ilmenites in different places.In processing of ilmenite through the Becher process, aeration rusting of pre-reduced ilmenite is found to be the rate limiting step thus, affecting the productivity of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half.A new route of processing ilmenite for synthetic rutile has also been developed in which, ilmenite is carbothermally reduced and then processed through plasma route. The slag thus obtained is processed further to get high-grade synthetic rutile, metallic iron and high purity iron oxide. The process has been scaled up in a continuous moving bed plasma reactor. It is technologically and economically more viable where, all the iron values are recovered as salable byproducts. This paper describes the salient features of the technologies developed for the beneficiation of ilmenite to synthetic rutile."

Jan 1, 2003

By Fangming Liu

The key problems of current flowsheets and equipments are analyzed. A new steel slag&apos;s crushing flowsheet whose key equipments are the improved inertia cone crusher and inertia vibrating jaw crusher is proposed. An advanced two stage open-circuit crushing method is adopted in the flowsheet, with 90% of particle size crushing under 6mm. Using inertia vibrating technology and selective crushing principle the crushers can realize steel slag separating fully into steel and slag and with flexible transmission mechanism the crusher can be protected when iron lump is passing. The flowsheets can enhance the recovery of metal greatly, and expand the application range of tail slag and added value.

Sep 1, 2012

By Axel Pankewitz, Andrew Smith, Mathias Stender, Christian Behrens

"Particle size measurement is one of the most important factors in obtaining peak performance of the mineral processing plant in order to ensure efficient milling and flotation circuit operation. Off-line particle distribution analysis technologies only allow an infrequent check of the ore slurry size and hence do not allow for timely process monitoring or intervention. Most existing on-line particle size analysers suffer from a variety of disabilities such as poor statistics, non-representative sampling or mechanically complex setup. This paper will describe an Ultrasonic Extinction based method which overcomes many limitations of existing online analysers and has proven its performance for mineral applications over many years. Installation examples will be given. Since new technologies usually raise e questions about comparability and agreement to common particle size analytical methods e.g. sieving or laser diffraction analysis, extensive studies were performed comparing these different technologies to quantify the quality of results as well as its mathematical robustness."

Jan 1, 2014