Search Documents

By Lucien Eaton

This paper describing the mining practices at Mine No. 1, Menominee Range, Mich., is one of a. series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. It is felt that the publication of this information will be of interest and value to the mining industry at large and especially to operators whose mining conditions are similar to those described. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of Mine No. 1 for much of the information presented.

Jan 1, 1929

By Willard L. Hunter

A series of steel heats, one low-alloy and nine carbon, was made by the Bureau of Mines in a 1-ton arc furnace from ferrous scrap from incinerated refuse, steel cans, and detinned steel cans, both alone and blended with heavy-melting scrap. Two additional control heats, one of carbon steel and one of low-alloy steel, were made from electric furnace heavy-melting scrap to pro-vide comparative data. The steel products were cast into two 4-by 4-inch nominal 50-pound ingots; in most heats, an 8-by 8-inch nominal 7S0-pound ingot was also obtained. Tests of these ingots indicated that reinforcing bars of acceptable quality can be made from urban refuse components such as steel cans.

Jan 1, 1976

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

This Bureau of Mines report is a compilation of information on computer models of mineral commodity markets in the Federal Government, The directory was compiled by the Analytic System Working Group of the Interagency Minerals Information Coordinating Committee to support the formulation of policies related to nonfuel minerals.

Jan 1, 1984

By G. L. Neumann

The Guymard mine in Orange County, N. Y., is reported to have been discovered in 1862 and mined until 1876, producing 10,000 tons of lead and zinc ore. The property was examined by an engineer of the Bureau of Mines in 1948. Development work was done by the Bureau in April and May 1949 and March 1950. During these two periods four drill holes totaling 2,090 feet were completed. The mineralized sections of the core were sampled and assayed.

Jan 1, 1952

By IRENE AITKENS

The Mining Law of 1910 , with amendments of 1914 and 1928 , is at present in force in the Dominican Republic . The first and basic mining law of the Republic was passed in 1876 , and although numerous changes and amendments have been made from time to time , the new laws and amendments thereto have not changed the original or basic law materially . However , these enactments have materially changed the legal methods governing the exploitation of the mineral resources of this country and have added new regulations and requirements to those concerning certain specific minerals , etc. The original or basic law still exists as it was first promulgated to protect the rights of the Dominican Republic itself , the rights of the landowner , and the rights of prospectors in general . The Mining Law of 1876 remained in force , without amendment , until it was superseded by the law of May 25 , 1904 , an enactment modeled after the Mexican mining law and designed especially to encourage the investment of

May 1, 1931

By G. L. Neumann

"INTRODUCTION AND SUMMARYThe Guymard mine in Orange County, N. Y., is reported to have been discovered in 1862 and mined until 1876, producing 10,000 tons of lead and zinc ore. 2/The property was examined by an engineer of the Bureau of Mines 3/ in 1948. Development work was done by the Bureau in April and May 1949 and March 1950. During these two periods four drill holes totaling 2,090 feet were completed. The mineralized sections of the core were sampled and assayed.ACKNOWLEDGMENTSThe diamond drilling was conducted under the general supervision of McHenry Mosier, chief, Mining Development Branch, Minerals Technology Division, Region VIII, and the direct supervision of Kenneth M. Earl and the writer as project engineers. Drill cores were logged by Paul K. Sims of the Federal Geological Survey. Chemical analyses were made by the Bruce Williams laboratories, Joplin, Mo., and the Minerals Processing Branch, Minerals Technology Division, Region VIII, Bureau of Mines, under the general supervision of Paul M. Ambrose, chief, and the direct supervision of Howard F. Carl, chief, Physical and Chemical Section.LOCATION AND ACCESSIBILITYThe Guymard deposit (see fig. 1) is on the west slope of Mount Hope, Orange County, N. Y., 1,500 feet northeast of Lake Guymard.Graham station, near the deposit, is on the Erie Railroad about 8 miles north of Port Jervis and 4 miles south of Otisville."

Aug 1, 1952

By D. S. Kingery

Owing to changes in State mining laws, the Maryland Bureau of Mines requires all mine foremen to have a thorough, practical knowledge of mine gases and the limitations and use of recognized gas-detecting devices. This requirement involves immediate training of second-grade mine foremen and aspirants to qualify them for certification under the new law. Cooperation of the Federal Bureau of Mines was requested, and a plan for training was discussed and adopted. The methods used in Maryland aroused unusual interest by participating individuals, and the final results were very satisfactory. Consequently, it is thought that this plan will be of interest and assistance to other organizations faced with the need for such training.

Jan 1, 1952

By E. G. Davis

Under a memorandum of agreement with Reynolds Metals Co., Richmond, VA, the Bureau of Mines studied the problem of corundum formation on refractory linings in aluminum recycling furnaces. A laboratory test was developed for evaluating refractories in contact with molten recycled aluminum and identifying the mechanism of corundum formation. A test apparatus was designed and constructed to evaluate the performance of refractory samples. Corundum mechanism formation studies indicated that corundum formed on refractories when there is metal penetration. Once corundum forms, it acts as a wick allowing the molten aluminum to move to the surface where it is oxidized, thus causing further growth of the corundum. Phosphoric acid treatment or a spinel mortar coating prevented corundum formation on the 70-and 90-pct-A1203 refractories.

Jan 1, 1988

By Harry Vivian

This paper deals principally with the retreating method of mining as applied in the Calumet & Hecla Consolidated Copper Co.'s deep Conglomerate mine, pointing cut some of the difficulties encountered in deep mining and describing the particular methods used at Calumet to carry on a large-scale operation at great depth with a minimum hazard factor. The circular is one of a series dealing with mining methods and costs which is being prepared for and published by the United States Bureau of Mines. ACKNOWLEDGMENTS Acknowledgment is due to those officials and operating heads of the Calumet & Hecla Cc. whose years of familiarity with the conditions developing at the Conglomerate mine as great depth was attained have enabled them to contribute valuable information to the subject of deep-mining problems.

Jan 1, 1931

By O. C. Ralston

Natural or artificial manganese dioxide of a grade pure enough to be satisfactory as depolarizer for dry cells has never been available in large supply simultaneously with being available in desired quality . The Second World War called for more of it than ever . A supply of natural material from the Gold Coast was ample for the war and was not completely exhausted . Whereas the crystal form of the manganese oxide was not recognized as a matter of importance until the war came , it is now known that gamma MnO2 is a desirable form and that pyrolusite , once thought acceptable , is not the best mineral . The following paper is a translation of an internal company report filed at the Bitterfeld office of the I. G. Farbenindustrie A.G. by Dr. Peter Marx in 1933 , just a year after G. W. Nichols had published in the Transactions of the American Electrochemical Society a study of making anodic manganese dioxide from solutions of manganous sulfate . The I. G. experiments were made to confirm the American work and were also extended to a larger scale . Only chemical purity was considered , and no mention is made of crystal form . The report adds to the knowledge submitted by Nichols but has not been previously available to the general public . Believing it of value to the United States industry , a translation has been made .

May 1, 1948

By J. William Ganser

This paper is one of a series being prepared by the United States Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1931

By Charles Vaught

The purpose of this study was to determine mine workers' state of fie-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers' responses are presented in this report, along with segments of narrative accounts, to profile miners' fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 2010

By Andrew Allan

[This report describe the first experiment of the Anthracite Research Laboratory, Bureau of Miners, in attempting to reduce underground-mining costs and conserve anthracite as a natural r-source by introducing now minim methods. The work war, dons in cooperation with one of the large anthracite-producing companies. It applies to productive mining, characterized by comparatively low cost, per ton and high production per man, as differentiated from development mining, which is always necessary before the, productive or retreat phase can begin. The system d scribed in this report is believed to be generally applicable to beds pitching 70° to 90° and, under certain conditions, to beds pitching loss than 70°. After development hate been completed, an openings is made, extending the full width of the 9- to 10-foot coal bad and reaching from the haulageway to the vertical limits of the solid coal. Long drill holes (20 to 50 feet) charged with about one stick of permissible explosive riper foot of length are fused to break the coal. Once broken, the coal is loaded onto a shaker conveyor by gravity and thence into mine: cars. The coal is mined retreating in 15- to 20-foot sections that are broken and loaded onto the conveyor through a specially constructed chute. In the Bureau?s experimental work, the height of sections arse ranged from 35 to 60 fact, depending on the geologic extent of the coal bed.]

Jan 1, 1952

By John B. Gayle

During studies of the various methods for determining and specifying the factors that indicate whether a particular coke is better or worse than other cokes for metallurgical uses, questions arose as to the precision of screen-analysis tests on coke. Although the usual index of precision, the standard deviation of the test result, gives a measure of the precision of these data, the experimental determination of the standard deviation for a particular set of conditions requires tests on a large number of duplicate samples. Because this procedure necessaily involves a great deal of labor, an equation for predicting standard deviations from theoretical considerations has been developed. Results predicted with this equation agree satisfactorily with the experimental values and are applicable to tests on coal, coke, gravel, and other bulk materials.

Jan 1, 1952

By L. D. Wyant

That natural gas-gasoline can be used to advantage as a refrigerant is suggested by the fact that the "make" tanks and other parts of the equipment of gasoline plants frequently become coated with frost. The experiments reported in this paper confirm this assumption and indicate that volatile gasoline can be use used to advantage in many refrigerating plants. The Bureau of Mines is making a study of wax distillates in order to find out why satisfactory lubricating oils and waxes can be made easily from certain crude oils and only with difficulty from others. In the commercial distillation of crude petroleum it is customary to separate the distillates into the following groups: (A) Gasolines and naphthas, (B) Kerosenes, (C) Gas oil, and (D) Wax distillate (consisting mostly of light lubricating oil together with small amounts of paraffin Wax).

Jan 1, 1923

By Andrew W. Berg

The Bureau of Mines Mineral Industry Location System (MILS) is part of the computerized Minerals Availability System (MAS), a comprehensive data base of known mineral deposits. MILS, the location subsystem of MAS, has become widely used by the minerals industry and organizations with land-use planning and land management responsibilities. Information on more than 135,000 mineral locations and processing plants in the United States is contained in the data base. This information includes the name, location, mineral commodity, type of operation, bibliography, and cross-references for each property or prospect. Computer-drawn map overlays at various scales showing clustered MILS locations and computer printouts keyed to those overlays are available for inspection and reproduction at the Bureau's Field Operations Centers at Juneau, Alaska, Denver, Colo., Pittsburgh, Pa., and Spokane, Wash.

Jan 1, 1979

By R. H. Reist, R. D. Dey, V. Castranova, J. P. Durham, Y. Rojanasakul

"Silicosis is a fibrotic pulmonary disease produced by inhalation of silica-containing dusts (Peters, 1986). Chronic silicosis may develop 20-40 years after initial exposure to crystalline silica, and the disease may progress from a simple to a complicated form. Few symptoms are evident in simple silicosis with pulmonary function being relatively normal. However, chest radiographs reveal small rounded ·opacities in the upper lobes of the lungs. These silicotic nodules consist of collagen arranged in a distinctive circular pattern. As fibrotic changes become more severe, the disease progresses to complicated silicosis (progressive massive fibrosis). Complicated silicosis is associated with shortness of breath and decreases in pulmonary function characteristic ofrestrictive lung disease. Chest x rays reveal numerous large silicotic nodules which may be associated with scar emphysema. Several mechanisms have been proposed to explain the cellular events which result in silica-induced lung damage and fibrosis (Lapp and Castranova, 1993). They include: ( l) direct cytotoxicity of silica, (2) activation of oxidant and enzyme release from alveolar macrophages, (3) recruitment and activation of polymorphonuclear leukocytes, and (4) stimulation of fibroblast proliferation and collagen synthesis.Tetrandrine is a bisbenzylisoquinoline alkaloid derived from the Chinese herb Radix Stephania tetrandra. It has a molecular weight of 622.73 and an empirical formula of C38H420 6N2. The chemical structure of tetrandrine has been published previously by our laboratory (Castranova et al., 1991 a). Its structure is characterized by methoxy groups at C7 and C12 , uncharged nitrogens at N2 and N’2 and two 17-carbon ring members connected by a double oxygen bridge between Ca-C7 and C11-C12. Tetrandrine has been shown to reduce both silica-induced fibrosis and the elevation of lung collagen content in rats (Huang et al .. 1981; Yu et al., 1983; ldel, 1987). Furthermore, tetrandrine has been used as an antifibrotic agent in Chinese clinical trials (Li et al.. 1981 ). Preliminary results suggest that administration of tetrandrine to patients with silicosis results in substantial improvement of symptoms, increases in diffusion capacity, and decreases in the size of shadows on lung x rays."

Nov 1, 1995

By C. T. Baroch

As part of a general program for investigating all phases of titanium production, argon was substituted for helium in the reduction step at the Bureau of Mines pilot plant, which employed a modification of the Kroll, or magnesium-reduction, process. Argon was substituted for helium in 108 of the 140 batches of sponge made during 1 month's reduction operations for July 1954. Argon was substituted for helium satisfactorily, with only slight modifications in technique. Metal quality, feed rate of TiC14, magnesium efficiency, and average production per batch were closely comparable with either gas. Argon runs were slightly more troublesome because of the formation of condensable chloride complexes, which tended to plug feed and vent lines and to entrap deposits of lower titanium chlorides on the reactor-pot lids. These lower chlorides were objection-able because they were pyrophoric and created obnoxious fumes when pots were opened. When feed and vent lines became plugged care was required in poking or unplugging these lines to prevent air from entering the reactor. These problems were relatively minor, and continued development of reactors and techniques for the use of argon should further minimize objectionable side reactions obtained when argon is used.

Jan 1, 1956

By H. Herbert Hughes

Soapstone commonly is associated with talc , and reports on either commodity usually contain a discussion of the other . From a geological or mineralogical standpoint the combination is justifiable , for soapstone essentially is impure talc . Commercially , however , the relation between them is remote . About 95 per cent of all talc sold in the United States is in ground form, whereas practically all soapstone is sold as furnace blocks or as fabricated structural slabs for many and diverse applications .

Feb 1, 1932