Search Documents

By Vernon C. Allison

The explosibility of coal dust has long been recognized by competent investigators as constituting one of the dangers of mining coal and in the use of pulverized coal as a fuel in industrial plants. The Bureau of Mines has carried on extensive series of experiments dealing with this subject, and has not only developed methods for the practical prevention of this danger, but in the, course of these experiments has developed a standard method of determining the relative explosibility of coal dusts and other organic dusts.3 Oil shale contains compounds 'of carbon and hydrogen that are either of a petroleum nature and are strongly ,adsorbed upon the incombustible part of the shale, or else are present in the shale as a compound ("kerogen") which has the property of changing into petroleum-like products when acted upon by heat. The oil shales may contain varying amounts of the organic matter, ranging from a trace to more than 66 per cent, depending upon their richness; therefore, it is important to know whether the dusts formed in mining and handling these oil shales are explosive when mixed with air and if so, to indicate remedial measures. This paper gives the results of explosibility tests of several pulverized oil shale's, selected as being typical of those which in the future may be used in commercial shale-oil production test on a sample of typical Colorado oil shale has been., published in an earlier paper.4

Jan 1, 1926

By Joseph Chalmers

[Stimulative methods of production, whereby the total recovery of oil from natural reservoirs is increased, have come into considerable prominence during the past 15 years. In many oil-producing areas properties considered ready for abandonment by ordinary producing methods have responded to some form of stimulation, and their economic lives have been extended. The stimulative method having widest application is the injection of air or gas into the reservoir formations through selected input wells and is commonly referred to as the ?gas drive." As a result of the many successful "gas-drive" operations operators are depending more and more upon this method for increasing the ulti¬mate recovery of oil from their properties. A number of factors influence the efficiency of different gases as propulsive agents in recovering oil from sands. Gases of high density and viscosity shrew a tendency toward a slightly higher efficiency than those of lower density and viscosity. The solubility of the gas in the oil also affects the efficiency of oil recovery. Not only does dissolved gas decrease the viscosity of the oil, but dissolved gas that expands from solution in the oil tends to increase the effectiveness of a "gas drive." Interfacial tension between the oil and the gas and its effect upon the recovery of oil by gas injection are factors of which little is known. Dr. A. G. Loomis5 expressed the opinion that interfacial tension probably plays a minor role in the recovery of oil, except under conditions that produce a gas-oil foam. In connection with the above physical properties that influence the action of a pressure medium, control of the injected volume of the pressure medium is perhaps the major factor. The rate ofg;as injection determines to a great extent the amount of slippage and the resulting efficiency of the operation. The importance of volume control is realized when one considers that frequently it is the only factor that is under complete control of the operator.]

Jan 1, 1930

By A. Wahab Khair, S. Jung

"This paper deals with the fracturing process of laterally confined blocks of coal subjected to impact indentation. During the test, blocks of coal with approximate dimensions of 10 in. x 10 in. x 6 in. were laterally confined to predetermined equivalent in-situ stresses and then subjected to an impact indentation by dropping coal cutting bits (various shapes) attached to a known weight from a known height. During the test a number of parameters, namely surface strains (using strain gages), penetration depth (using L.V.D.T.) and acoustic emission characteristics were measured. After the test, the fractured surfaces were photographed with the aid of a camera attached to a microscope. The fracture, its intensity and extended zone within the coal blocks were mapped using sonic techniques. By correlating measured parameters, fractured zones under a given set of test parameters were identified and characterized.INTRODUCTION To improve the understanding of basic failure mechanisms in coal cutting, a better knowledge of fracture and crack regions caused by the indentation in coal is needed. This study reports the detailed experimental procedure used in fracture analysis of indentation experiments on coal specimens using the Acoustic Emission (A.E. hereafter) and sonic techniques. The relationship between microcracking and the inelastic deformation of rock was confirmed by a series of experiments in which the A. E. generated by the cracking in the rock specimen were recorded and the number of events were compared to the strain measurement. (Scholz, 1967).According to fracture mechanism theory, crack initiation in brittle materials such as rocks begins from ""flaws"" either pre-existing or induced by the indentation process itself. Rocks are pervaded by natural cracks and pores, from which numerous possibilities for crack initiation arise (Lindquist, Lai and Alm, 1984)."

Jan 1, 1989

By H. C. Brunaugh, James Westfield, R. W. Whittaker

"INTRODUCTION The purpose of this circular is to describe the sealing off of a mine fire and subsequent use of carbon dioxide gas to extinguish it.A fire of electrical origin occurred in the Valier mine of the Valier Coal Co., Valier, Franklin County, I11., on March 29, 1949, at about 1:35 p.m. It was discovered about 3:35 p.m. in 5 south west intake airway inby 1 and 2 west panels. The No. 5 southwest airway had caved, and the fire was in the top coal beneath a large fall of rock. All men, except officials, were ordered from the mine. The mine officials decided to seal the fire, and four temporary seals were erected, which isolated approximately 200 feet of 5 south west entry. The seals were completed on March 30 at 2:45 a.m., but on March 31, at 3;40 a.m,, two of them were blown out by an explosion of gas that was produced by the fire. The two seals were rebuilt, the work being completed on March 31 at 12:00 noon, but they were blown out by another gas explosion at 12:10 a.m. on April 1. It was then decided to extinguish the fire with water if possible.To accomplish this, concrete-block dams were constructed. On April 1, about 4:25 a.m., when the dams were about half completed, water was introduced into the fire area through a 2-inch pipe.On April 4, J. G, Crawford, general manager of the Valier Coal Co., notified James Westfield, chief of the Vincennes (Ind.) Branch, U. S. Bureau of Mines, by telephone of the fire in Valier mine and requested assistance to combat it. Westfield, accompanied by F. J. Smith and H. C. Brumbaugh, Federal coal-mine inspectors, went underground and inspected the seals and dams. Later, during a conference with company officials, it was decided that the concrete-block dams were not strong enough to withstand the hydrostatic pressure that would be produced by flooding the fire area. It was then decided to use carbon dioxide gas to extinguish the fire. Four seals were completed, and 5 tons of carbon dioxide gas was introduced into the fire area, which extinguished the fire."

Apr 1, 1950

By A. Gene Collins

Some of the geochemical relationships that exist between subsurface fluids and the associated geologic strata in petroleum producing areas of Louisiana have been determined. Samples of petroleum-associated water were obtained from 126 wells in Louisiana that produced from sediments of three geologic ages: Tertiary, Cretaceous, and Jurassic. The samples were trans-ported to a central laboratory for analysis of chemical composition, using standard methods, to determine if the compositions varied with the geologic strata of their source and, if so, why. The dissolved constituents were com-pared with those of a brine that was concentrated by evaporation. The concentrations of bromide, calcium, and strontium were useful in distinguishing the brines produced from sediments of a late age from those of an earlier age. The concentration ratios of Mg' (total equivalent magnesium) and bromide indicated that dolomitization probably had occurred and altered the composition of the brines. A principal-components analysis of the data indicated an inverse relationship between depth and concentrations of bromide, strontium, calcium, and lithium.

Jan 1, 1970

By Van E. Shaw

Bastnaesite is a natural rare-earth fluorcarbonate of the cerium group that affords an abundant and high-grade source of the lighter rare-earth elements. A simple and efficient method has been developed by the Bureau of Mines for extracting rare-earth compounds from this mineral. Digesting of a flotation concentrate with sulfuric acid converts the rare-earth compounds from fluorcarbonates to sulfates. Action of the acid releases gaseous com-pounds of fluorine and silicon, leaving the sulfated material free of these elements; carbon dioxide from carbonate decomposition is eliminated at the same time. Calcining the sulfated material at 1,200° F. renders the gangue constituents insoluble, whereas the rare-earth sulfates are left in water-soluble form. Leaching with water yields a solution of pure rare-earth sulfates. Bastnaesite could become prominent as a source of cerium-group rare-earth elements. It is rich in the light rare-earth elements and comparatively easy to process; reserves of the mineral are extensive enough to supply a greatly expanded market for many years.

Jan 1, 1959

By Todd M. Ruff

Current methods of inspecting wire rope for broken wires or excessive wear include visual inspection, physical measurements of rope diameter, and electromagnetic nondestructive testing (NDT). Visual inspection and physical measurement arc the least comprehensive methods. Electromagnetic NDT enables a more thorough assessment of the condition of a wire rope, but the repeatability, accuracy, and objectivity of this method can be improved. One means of achieving this goal is to use a computer to analyze the test data and determine the condition of the wire rope, including the presence of broken wires and corrosion, and the amount of wear. An off-the-shelf data acquisition and analysis system was tested in a U.S. Bureau of Mines laboratory using a continuous loop of wire rope containing fabricated flaws. The test rope was run through a commercially available NDT instrument. The output of the instrument, normally connected to a paper strip chart recorder, was digitized and analyzed with a personal computer. These initial tests were successful in showing that the use of a computer can improve current methods of NDT waveform collection and analysis.

Jan 1, 2010

By Steven J. Page, John A. Organiscak

Prolonged exposure to airborne respirable coal mine dust is responsible for coal workers' pneumoconi¬osis (CWP): Furthermore, miners who show evidence of higher radiographic categories of simple CWP are at increased risk of developing progressive massive fibro¬sis (PMF). As of 1990, there were nearly 130,000 coal miners in the United States. "' This excludes mines that produce less than 10,000 tons annually and the anthracite coal mines. Estimates indicate that at age 58, an average of 7/1000 U.S. workers and 89/1000 U.K workers will have developed PMF(2-1) Health research studies have iden¬tified that the risk of developing and the severity of CWP arc directly related to (1) the amount of respirable dust exposure and (2) the coal rank.,'- The rank of coal is its stage of formation in the series peat, lignite, sub-bituminous, bituminous, and anthra¬cite (in order of increasing rank). The rank of coal can also be represented by the com¬mercially important characteristics specified by its proximate analysis: fixed carbon, vol¬atile matter, mineral matter, and moisture content.

By E. W. Pehrson

In making any canvass of secondary metals great care must be exercised to avoid duplication or exaggeration of net consumption. One of the major difficulties is to trace the metal accurately as it passes through the many cycles of manufacture. Greater or less duplication probably occurs in any canvass. The manufacturer of tin plate, for instance, purchases primary pig tin exclusively as a raw material. Most of it goes into the coating on the steel sheet, but a substantial part emerges in the form of byproducts such as scruffs and drosses. These are sold to other plants, where they are used in the manufacture of alloys and chemicals. Alloys and chemicals, however, are not necessarily articles for final consumption. The alloy may be sold in ingot form to a bearing manufacturer, who, in turn may produce some scrap, which he may sell to still' another plant that may make still other products. There is a considerable return of tin in the form of waste products from chemicals sold to the silk industry. Even tin plate does not represent an ultimate use of tin because the tin-can maker produces large amounts of clippings, which are sold to detinning plants, where the tin is recovered and used again for some other purpose. Thus the degree of duplication in consumption statistics depends on the point in the industrial cycle where consumption is measured.

Jan 1, 1936

By L. R. Willmott

An ethanolamine purification unit for removing carbon dioxide and hydrogen sulfide from Firscher-Tropsch synthesis gas was installed at the Bureau of Mines synthetic liquid fuels demonstration plant at Louisiana, Mo. The unit was a surplus Radford Girbotol unit from the Missouri Ordnance Works modified for a capacity of 90,000 std. cu. ft per hour of synthesis gas at 450 p.s.i.g., operating pressure. The hydrogen sulfide loading of the feed gas was specified at 500 grains per 100 cu. Ft. The unit was designed by the Girdler Corp. and installed by the Koppers Co. Initial operations were conducted far 11 days in May 1951. Thereafter 7 additional runs were made, varying lo duration from 8 to 54 days. The last run was terminated on May 29, 1953, the total time the Plant wars in operation being 219 days.

Jan 1, 1956

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By Oliver C. Ralston, Foster Fraas

The electrostatic separation of solids utilizes the forces exerted when electrically charged particles of the solids are present in an electric field . The charges may be acquired by various means (5) , and when the acquisition or loss of charge depends on the property of the particle , separation can be obtained between particles having different properties . A property commonly utilized in present - day separators in conductance . Charging also may be accomplished by bringing the particles into intimate contact with various surfaces . This is sometimes described as a " frictional electrical effect. The charge , or specifically the polarity of the charge , in this latter case evidently depends on the property known as the contact potential , as has been explained in the discussion of a paper (7) and in several other papers (10) . Separation by this method is accomplished in two steps - a charging step , in which the particles are brought into intimate contact with an electrification surface , and a separation step , in which the charged particles are separated in an intense electric field . Descriptions of such methods may be found in the literature (2) , (7) , ( 8) . Even as early as 1909 , Blake and Morscher (2) described the charging of particles by intimate contact followed by separation in an electric field . They also state that the polarity of the electrical charge acquired by the particles depends on their composition . O'Brien ( 8) presented several designs of apparatus . He obtained electrification by means of a wiping action , either on inclined plates or in rotating cups , in which a centrifugal force was imparted to the particles .

Nov 1, 1942

By D. J. MacDonald

The Bureau of Mines investigated two alternative methods for treating a zirconium-bearing chloride-sulfate strip liquor to obtain reactor-grade Zr02. One method involves neutralization with NH3 and the other hydrothermal precipitation. The strip liquor was derived from zircon sand by a Bureau of Mines method for separating zirconium and hafnium via solvent extraction with a tertiary amine. Neutralization with NH3 to precipitate hydrous zirconium oxide required 0.9 to 1.1 g NH3 per gram of zirconium. The NH3 can be recovered for recycle. Zr02 that met reactor-grade specifications was produced by precipitation with NH3? Hydrothermal precipitation of Zr02 from strip liquor required that the solution be maintained at 2600 C and 680 psi for 10 min and in a non-corrodible pressure vessel. In bench-scale experiments both methods gave-zirconium recoveries greater than 99 pct.

Jan 1, 1984

By R. D. Leitch

"REASONS FOR AND PURPOSE OF WORKIn 1924 the United States Public Health Service was requested to undertake a special study of stream pollution. At that time the proposal that the United States Bureau of Mines take up the study was made by the Public Health Service because in point of training and experience the personnel of the latter was considered not to be as well, suited to this type of investigation as was that of the Bureau of Mines. H. Foster Bain, then Director of this bureau, promised to undertake the work, and, accordingly, field investigations were begun in the spring of 1925. The problems of mine-drainage wastes and of gas-house and coke-oven waste were investigated in the laboratory, and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau of Mines experiment stations, while in Germany in 1924, where he was shown a practical application of the process, but no information was obtained as to definite chemical or mechanical processes. Because of the then pending American patent application by the German firm, we made no attempt to develop our findings further. Shortly after, a similar method of treatment was developed in the United States, and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage.SCOPE OF WORKAt the time our work was begun there was such a diversity of opinion on the whole subject and apparently so little was accurately known, that it was decided to undertake a basic study from which (1) certain definite information might be evident, and (2) what might be considered side issues of the original investigation would be suggested for subsequent study.A stream in a district thought to be representative of those in low to average sulphur bituminous coal fields and another in a high sulpbur district were selected for study, A fair (weber of factors entered into the tentative selection of these streams, the chief ones being their accessibility and freedom from other industrial or domestic pollution, besides, of course, the presence of mine drainage in these streams."

Apr 1, 1931

By Curtis D. Edgerton

The Pittsburgh Mine Map Repository of the Bureau of Mines serves as a basic reference file for the archival preservation of mine map data of mines east of the Mississippi River. About 22,000 of an estimated 500,000 available mine maps have been microfilmed A computerized index serves as the mechanism for retrieval of any microfilmed mine map. The operation, equipment, and index are described in the report.

Jan 1, 1974

By L. Y. Sadler

The Bureau of Mines conducted a study Lo determine the loss in weight of silica (Si02) volatilization from low-alumina (A1203) refractories used as hot face liner materials in such process equipment as coal gasifiers, synthesis gas transfer lines, and ammonia plant secondary re-formers. Small specimens of 80-and 40-pct-A1203 brick and 95-pct-SiO2 brick were exposed to steam in high-pressure furnaces at pressures of up to 1,000 psig and temperatures up to 1,400° C for periods ranging up to 120 h. Weight losses from the 40-pct-A1203 brick after 40 h of exposure were highest, 2.75 pet at 1,400° C and 1,000 psig. The rate of weight loss had dropped to near zero after 80 h of exposure at all temperatures. No relationship between total silica content of the specimen and weight loss could be established nor did scanning electron microscopic examination of the specimens before and after exposure identify specific regions (e.g., surface) suffering a disproportionate share of the silica loss. It was concluded that minor silica volatilization is likely to occur, if at all, at temperatures of less than 1,000° C and pressures below 1,000 psig, and that low-alumina refractories should be used as dry-ash coal gasifier hot face linings.

Jan 1, 1986

By David M. Hyman

The Bureau of Mines has developed two experimental designs for deter- mining the volumes and relative proportions of the various gas species, particularly methane (CH4), occluded in rock salt. To date, the rock salt samples analyzed have been relatively small (400- to 1,000-gram) grab samples from Louisiana Gulf Coast domal salt mines. The results obtained are comparable to results in Polish domal salt mines, in terms of occluded gas volumes per mass of rock salt. The notable difference between the Louisiana and Polish occluded gas mixtures is in the relative proportions of the individual gas species. The two methods used by the Bureau are ballmill crushing and dissolution. Of the two, the dissolution method appears to be more versatile because it can be performed in situ. The relevance and applicability of data on the occluded gas contents of rock salt are dependent on sample size, sample collection method, geologic context of the sample, and the correlation with gas emissions that occur as a result of mining-induced fractures and pressure differentials.

Jan 1, 1982

"Minimizing Particle Contamination During Generation of Fresh Dust for Inhalation Studies J. Abraham, MS, Mechanical and Aerospace Engineering, West Virginia University, 1995Correlating Lung Crackle Using Holographic Interferometry Ali Afshari, MS, West Virginia University, 1989Effect of Bit Wear on Dust Generation Mudassar Ahmad, MS, West Virginia University, 1992 The Effect of Surfactants on Suppression of Non-Wettable Particles Ali Alaboyun, MS, Mineral Engineering, The Pennsylvania State University, 1989 Geochemical Characterization of Kerogens, Shales, and Coal Refuse Associated with Allegheny Formation of Cases of Northern West Virginia Dick Andre, MS, West Virginia University, 1987Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment Indranil R. Bardhan, MEM Report, The Pennsylvania State University, 1992Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment I. Bardhan, R. V. Ramani, and J.M. Mutmansky, Mining Engineering, The Pennsylvania State University, University Park, PA, Final Report to the U.S. Bureau of Mines, April, 1994Particle Concentrations in a Hazelton Inhalation Chamber Shahram Bavani, MS, West Virginia University, 1985Use and Potential of Lazer Holographic Interferometry and Subsidence Model- Study of an Underground Room and Pillar Mine Richard Begley, MS, West Virginia University, 1984Development of a Mechanistic Model for Prediction of Subsidence in a Longwall Mine Richard Begley, PhD, West Virginia University, 1990Redesign of Micro-Orifice Uniform Deposit Impactor Steve Behm, MS, University of Minnesota, 1991Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle, MS, The Pennsylvania State University, 1996Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle and R.-V. Ramani, The Pennsylvania State University, University Park, PA, Final Report, September 9, 1996A Fracture Mechanics Study of Crack Propagation Mechanism in Coal: The Mechanics of Fine Fragment Formation Z.T. Bieniawski and R. Karl Zipf, Jr., Mining Engineering Department, The Pennsylvania State University, University Park, PA. Final Report, October l, 1988A Mathematical Model for the Prediction of Ambient Dust Concentrations in Mine Atmospheres R. Bhaskar, MS, Mining Engineering and Operations Research, The Pennsylvania State University, 1984Spatial and Temporal Behavior of Dust in Mines-Theoretical and Experimental Studies –R. Bhaskar, PhD, Mining Engineering, The Pennsylvania State University, 1987"

Jan 1, 1998

By I. AITKENS

Quartz maintains a rather conspicuous position among gem stones , despite its being the commonest and, in its natural form, the most easily recognized of mineral substances . This prominence is due primarily to the extensive use of amethyst , which provides stones of the finest violet color , and also to the wide employment of yellow quartz ( citrine ) which is called topaz by jewellers and vies with the true topaz in color and brilliance . Unlike many less costly gem materials quartz is hard and durable .

Mar 1, 1932

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963