Search Documents

By B. P. Watson

Uniaxial tests performed on core from instrumented sites at Amandelbult 1 shaft, Impala 10 shaft and Union Section Spud shaft showed a nonlinear elastic relationship between applied load and induced deformation. This nonlinear behaviour does not appear to be dependent on borehole orientation but in the case of the Amandelbult and Union sites appears to have been influenced by the stress condition of the rock mass at the time of drilling. Cores drilled at these two sites under destressed conditions, such as over a stope, showed a linear elastic response to the applied load whereas most of the cores drilled under relatively high radial stresses were nonlinear. The Impala 10 shaft tests, however, all showed strong nonlinear behaviour irrespective of the stress condition of the rock mass at the time of drilling, although high stress conditions may have influenced the severity of the nonlinearity. A comparison between underground stress change measurements and an elastic model indicated that the rock mass became nonlinear when the virgin stress condition was relaxed to about 10 MPa. The cores for laboratory testing were retrieved from vertical boreholes drilled up from the centre of a stope and from horizontal boreholes drilled over pillars and stopes at about 600 m, 1 100 m and 1 400 m below surface for the three sites respectively. The k-ratios under virgin conditions were estimated from sockets, modelling and stress measurements to be 1.0, 1.3, and 0.5 for the Amandelbult, Impala and Union sites respectively. Of the three sites, therefore, Impala 10 shaft appears to have had the highest virgin stress state. Tests performed on similar rocks from shallower depths at Impala Platinum essentially showed a linear relationship between stress and strain. From the small Impala Platinum rock test database available to the project, it appears that the nonlinear elastic behaviour initiates at this mine from about 1 000 m below surface and seems to become progressively more nonlinear below this depth. In addition, the nonlinear elastic rocks are weaker, have a lower Young?s modulus and a higher Poisson?s ratio than their linear elastic equivalents. Interestingly the tangential Poisson?s ratios of the nonlinear elastic materials are often greater than 0.5 at 50% of the failure stress, suggesting an early failure initiation. The paper describes the microscope and modelling work done to determine the causes of the nonlinear behaviour and discusses some implications of the behaviour for deep-level mining.

Jan 1, 2009

By A. Yamik

This research study includes studies carried out on the recovery of unburned carbon in the ashes of Tuncbilek Thermal Power Plant. Bottom ashes have been identified by X-ray diffraction and X-ray fluorescence. These samples are potentially of class F type and have significant amounts of unburned coal. According to the ash amount that units in the thermal power plant produce, and the analyses of the samples mixed, which used certain amounts in flotation tests, it was found that the bottom ash includes 91.47% ash in dry form and 8.53% combustible matter, and the lower calorific value is 491 kcal/kg. Optimum flotation conditions to get the unburned carbon were subsequently determined by examination of the optimum flotation grain size, pulp density, collector type and amount, depressant type and amount, frother type and amount, agitation speed, and froth-taking time. While the lower calorific value of the thermal power plant bottom ashes of the 3rd , 4th and 5th units and the mixed bottom ash sample was, respectively, 959, 469, 279 and 491 kcal/kg in dry form, it increased to 2490, 1312, 786 and 1348 kcal/kg in the product obtained as a result of flotation in optimum conditions. Key words: ash, conventional flotation, unburned carbon

Jan 1, 2008

By G. P. A. Howe

"A computer model of the rutile, ilmenite and zircon industry was developed jointly by Associated Minerals Consolidated and Consolidated Gold Fields for exploring marketing strategies and making predictions over a ten-year period. The industry is described briefly and the reasons for modelling it and choosing a deterministic approach explained. The economic structure of the model and its level of complexity are discussed. The necessity and techniques for convenient input and clear output, the team composition and the method of work are discussed.The reasons for the choice of FORTRAN, large computers, remote batch terminals and the vital importance of fast turn-round are discussed.Costs in staff time and computing are given, with an assessment of the reasons for the success of the model. The model is used on a regular basis to aid management decisions."

Jan 1, 2014

By B. McFadzean, M. Becker, S Geldenhuys, A. Molifie

Mineral hydration is known to result in low flotation recoveries and grades within primary platinum group element ores worldwide. This is because the phyllosilicate minerals derived from hydration reactions of silicate minerals (i) form electrostatic coatings on valuable minerals that in turn hinder collector adsorption, (ii) alter the viscosity of the slurry leading to poor gas dispersion and (iii) decrease the concentrate grade due to naturally-floating gangue. Sodium silicate was investigated because its dispersant, rheology modifying, and depressant properties could prove promising in combating the problems associated with these ore types. Quantitative evaluation by scanning electron microscopy analysis revealed large quantities of serpentine and talc present within the ore sample used in this study, which led to a poor flotation response as indicated by batch flotation tests. Using sodium silicate improved the recoveries and grades at high dosages (>1000 g/t). The zeta potential experiments indicate that improved recoveries are, in part, as a result of the reversal of serpentine surface charge, creating electrostatic repulsion between serpentine and valuable minerals which prevents the coating of valuable minerals by serpentine slimes. Ore dilution and rheology tests indicated that decreased viscosity at high dosages also improved recoveries. Talc micro-flotation tests revealed that the depression of talc occurred at higher sodium silicate dosages, which improved concentrate grade. The processing of nearsurface altered ores is becoming an increasing problem worldwide and the use of sodium silicate proved valuable in mitigating the problems associated with the altered ore investigated in this study. Keywords: Alteration, phyllosilicate slimes, colloidal chemistry

Jan 1, 2020

By J. Petersen, K. Shaik1, H. Kolev, Z. Cherkezova-Zheleva

Sperrylite is one of the most abundant platinum minerals globally, valued for its economic importance but also known for its highly refractory nature, making it difficult to process via the conventional route. This study explores the oxidative leaching of sperrylite using a cyanide–ferricyanide system, with a key focus on characterisation of the mineral and surface speciation under varied leaching conditions using x-ray photoelectron spectroscopy. The parameters investigated include the effect of sodium cyanide concentration, the use of potassium ferricyanide as an oxidant, copper sulphate pentahydrate as a catalyst, as well as the effects of temperature and particle size. A limited set of leaching tests was carried out to study the surface chemistry rather than optimising dissolution conditions. This approach identified mineral oxidation states and shifts in binding energies, prior to and post leaching. XPS analysis of sperrylite’s surface chemistry identified key species, comprising the bulk Pt(II)–As (≈73 eV) and As(–I)–Pt (≈41.8 eV) states, together with surface oxidation products Pt(II)–O (≈72 eV), Pt(IV)–O (≈74.5 eV), As(III)–O (≈43 eV) and As(V)–O (44.5 eV). Leaching led to the removal of pre-existing oxides on the ultra-finely ground sample, exposing the underlying bulk species. In contrast, the crystalline sample with an initial low concentration of oxides, generated higher amounts of fully oxidised species after leaching, reflecting greater surface reactivity.

Mar 6, 2026

By Kevin Peacocke

The future of Gravity ? Primary mineral recovery ? Enhancement of existing process efficiency ? Pre-Concentration ? Alternative? or ?New? production

Jan 1, 2006

By L. Forbes, G. Forbes, J. Wang

Bubble size measurement is a vital part of flotation system analysis and diagnostics. Over the years, a great many different bubble size analysis tools have been developed. However, all of them rely on ex-situ measurement and in-pulp sampling techniques. This paper evaluates the Mettler Toledo ParticleView™ Measurement probe as a novel method for in-situ bubble size measurement. This device is then compared to the conventional Anglo Platinum Bubble Sizer (StoneThree). It was found that the in-situ bubble size analysis technology appears to be a more user-friendly and reliable option for determining bubble size in flotation. However, the current instrument design is not suited to industrial applications. Keywords: Bubble size measurement, bubble coalescence, PVM probe

Jan 1, 2020

By A. W. Sundström

This paper reviews the development and suitability of various important thermophysical and electrical properties with respect to base metal mattes. Areas of focus include the critical validation of measurements of viscosity, density, surface and interfacial tension, electrical conductivity, and an overview of the various experimental methods used to determine these properties. Accurate physical property data of mattes are critical in process modelling and computational fluid dynamic modelling of smelting and converting operations employed in the extraction of copper, nickel, cobalt and platinum group metals.

Jan 1, 2008

By M. Gericke

The microbial leaching of metal sulfides is now an established biotechnological technology. Over the past 25 years, refinements in the engineering design of bioleaching processes have paralleled advances in our understanding of the diversity and role of the micro-organisms driving the process and the mechanisms by which micro-organisms enhance metal sulfide oxidation. Commercial success started with the treatment of refractory gold concentrates using mesophilic micro-organisms, followed by the development of tank bioleaching processes for the treatment of base metal concentrates. This was, initially, a mesophilic process with limited potential for recovery of copper from chalcopyrite concentrates due to slow rates and low copper extractions. The exploitation of thermophiles represents a major breakthrough in the development of bioleaching technology for the treatment of chalcopyrite-containing ores and concentrates. This development also opened the route to heap bioleaching of chalcopyrite ores, which is now a major focus of research programmes and piloting campaigns. This paper reviews the historical development of minerals bioleaching processes and gives an update on the current status of commercial tank and heap bioleach operations around the world.

Jan 1, 2009

By Bosman

Medium suspensions play an integral part in the successful application of dense medium separation for both static and dynamic separators. Although models exist to predict particle movement as a function of medium density and viscosity, these models have been derived on the assumption of Newtonian rheology. Viscosity measurements of medium suspensions have shown that they are non-Newtonian, with a yield stress, and as such cannot be used in the existing models. As a result, medium selection remains an art based upon practical experience and indirect measurements of viscosity such as stability and cyclone differentials.

Jan 1, 2014

By H. Karabulut, S. Gündüz, K. Karacif, M. A. Erden

The corrosion properties of iron-based composite materials containing graphite and silicon carbide (SiC) reinforcement were investigated. The effects of silicon carbide reinforcement were investigated by adding 0.5% graphite and 1%, 2%, and 4% SiC. A powder metallurgy method was used to produce the composite samples. Iron, graphite, and silicon carbide powders were blended for one hour with a threeaxis mixer and then unidirectionally pressed under a pressure of 750 MPa. After pressing, the composite materials were sintered at 1100°C for one hour. The corrosion properties and microstructure, density, and hardness properties of the composite materials that can affect the corrosion properties were also investigated. It was determined that the pore ratio and hardness of the composite material increased, and corrosion resistance decreased, with increasing silicon carbide content.

Jun 2, 2022

The proper understanding of the functioning of ground support under dynamic loading and the current approaches to designing of dynamic support are plagued by a great deal of uncertainty and lack of knowledge. This applies equally to the understanding of the support capacity as well as the demand placed onto the support due to dynamic loading. This lack of understanding currently leads to a case of design indeterminacy. This paper does not aim to solve this problem of design indeterminacy but to explore some of the issues that need consideration to obtain a better understanding of the dynamic demand on ground support systems. Keywords ground support, dynamic loading.

Dec 1, 2013

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

Primary roof support represents the first line of defence against rockrelated falls of ground in underground mines, and improper utilization or misunderstanding of the applicability and behaviour of primary support can be costly from a safety standpoint. This is a major concern for underground mines, as roof support is the single most costly expense from a mining operational perspective. This is further backed by the evidence that, in the USA, hundreds of injuries and fatalities still occur each year because of rib, roof, and massive roof falls. Additionally, the fully-grouted passive rebar, fully-grouted tension rebar, and resin-assisted mechanical anchor bolts, which constitute a large portion (89%) of the 68 million bolts installed each year in underground mines in the USA can vary in cost quite dramatically. To mitigate this concern a study was conducted in 2010 by the National Institute of Occupational Safety and Health, in conjunction with Southern Illinois University of Carbondale, to assess the performance of primary roofbolts in underground coal mines for improved safety and cost. This was accomplished using underground roofbolt monitoring solutions, field data, and numerical modelling to better understand the quasi-static behaviour of underground coal mine roofs and the response behaviour of the bolts. In particular, over 170 instrumented extensometers, closure meters, shear meters, fully-grouted passive rebar, fully-grouted tension rebar, and resin-assisted mechanical roofbolts were installed at three coal mines across the USA. Of these three mines, two used the room and pillar extraction method and the other used the longwall extraction method. There was no evidence to indicate a difference in performance of the active primary roofbolts compared with the passive primary roofbolts. Additionally, in the initial loading phase, the active bolts showed no difference in loading, indicating that tension bleed-off is of more of a concern than originally thought. Lastly, for the initial computer modelling studies, challenges still remain in obtaining a good match to the in situ bolt measurements and replicating the discontinuous roof rock and in situ bolt behaviour over time.

Jan 1, 2014

By J. W. Drelich, H. Zeng, L. Xie, X. Cui, Z. Gao, M. Tian, Y. Hu, W. Hu, W. Sun

Flotation is a mineral separation technology that uses the surface hydrophobic difference of valuable minerals and their associated gangue minerals to separate them. The flotation collector adsorbs on the valuable mineral surface to improve its hydrophobicity, and metal ions are usually used as activators to enhance the collector adsorption. Different mineral surfaces show different charging properties and adsorption behaviours with the collector or metal ions. Moreover, the order of adding metal ions and the collector also show significant and different flotation performance for the same mineral. The adsorption or flotation behaviour or both are governed by mineral surface chemistry, such as surface charging and reactivity. In our recent studies, force measurement using atomic force microscopy (AFM) was employed to study the surface charging and adsorption mechanism of metal ions and collectors. By preparing collector-functionalised AFM tips, AFM can directly measure the adsorption strength of the collector on the mineral surface to determine the anisotropy of mineral surface reactivity. The preparation of collector-functionalised AFM tips provides the foundation for further study of the activation role of metal ion in the collector adsorption. The application of AFM for force measurement in the surface chemistry of mineral flotation can provide important information on developing flotation reagents and lays the foundation for the specific regulation of mineral surface characteristics. Keywords: Scheelite; flotation; surface chemistry; AFM force measurement

Jan 1, 2020

By T. Orupold

This paper covers the commercial development of gravity separation of fine particles using a Lamella High Shear Rate REFLUX? Classifier (REFLUX? Classifier), focusing primarily on coal applications. The REFLUX? Classifier is a fluidized bed device that incorporates a system of closely spaced parallel inclined channels located above the fluidized bed. These channels make it possible to achieve a significant suppression of the effects of particle size, resulting in a highly effective separation on the basis of density. The improved gravity separation performance is shown to be remarkably high, with a significant reduction in the variation of separation density with particle size, and a significant reduction in the change in Ecart probable error (Ep) with size. The first full commercial-sized units of the REFLUX? Classifier were field-tested in late 2009 in coal applications. More recently, the technology has been applied in fine particle separation in minerals applications and there are a number of full-sized units operating in chrome applications in South Africa. Initially, pilot-scaled units (typically the RC?300) were trialled in iron ore, mineral sands, and manganese plants amongst other minerals, typically after other technologies failed to achieve the desired results. Currently a number of laboratories globally are carrying out more testing in minerals applications. More than 50 RC? units are now operating in coal and minerals applications. This paper introduces the REFLUX? Classifier technology, identifies commercial applications, and gives some commercial results.

Jan 1, 2014

By J-N. Oyourou, R. McCrindle, C. J. S. Fourie

"Many mines in South Africa were inappropriately closed and left unattended during the last century. These old mines are potential sources of environmental pollution and may pose a health risk to local populations, since the surrounds contain elevated levels of toxic elements. Soil from the old Edendale lead mine property in Mamelodi Extension 11, east of Pretoria, which was suspected to be contaminated with lead, was analysed. The mine, which primarily extracted galena, was decommissioned in 1938. During this study, the old mine property and surrounds were screened for zinc and lead using a field-portable X-ray fluorescence (pXRF) spectrometer. The metal concentrations, which ranged from 18 to 7 300 mg/kg for zinc and from 50 to 21 000 mg/kg, for lead, were plotted together with the GPS coordinates to produce a concentration distribution map for lead and zinc. This map revealed three anomalies of unacceptably high concentrations, possibly corresponding to areas where ore had been piled or dumped to waste from the old mine. Thirty-six of the soil samples that were analysed by pXRF on site were selected and analysed in the laboratory using inductively coupled plasmaoptical emission spectrometry (ICP-OES) for verification purposes. The zinc and lead concentrations obtained from the two analytical methods were compared using linear regression analysis. Excellent correlation was obtained between the results from the two methods (r2 = 0.99 for zinc and r2 = 0.95 for lead). IntroductionEarly economic development in South Africa was based mainly on mining. However, these activities left a legacy of approximately 6 000 improperly closed mines scattered throughout the country (SAI, 2009; van Schie, 2012). Due to their proximity to settlements, these abandoned mines may pose a potential health risk to humans and an environmental hazard. Mining activities generate large amounts of waste, mostly in the form of overburden and process tailings, which often contain high concentrations of toxic elements. Bioavailable toxic elements can contaminate crops growing in the polluted area (Kala, 2010; Marwa, Meharg, and Rice, 2012) or eventually migrate and detrimentally affect the groundwater (Rösner and van Schalkwyk, 2000). Moreover, sulfides accumulated in mine waste generate acid minewater (Rösner and van Schalkwyk 2000). Unfortunately, owners of mines, closed before the promulgation of the Minerals Act more than twenty years ago (Act 50 of 1991), avoided the compulsory rehabilitation of the environment enforced by this legislation. Toxic elements, such as lead, which were confined within ores, may become exposed through mining and are therefore more easily mobilized within the environment. Elements essential to human and plant metabolism, such as zinc, when exposed by mining activities, may become hazardous due to elevated concentrations (Aslibekan and Moles, 2003; Wuana and Okiemen, 2011). Humans exposed to potentially toxic metals may experience harmful effects as discussed elsewhere (Nriagu and Pacynar, 1988; Wayne and Ming-Ho, 2005)."

Jan 1, 2019

By C. O. Aksoy, G. G. U. Aksoy, A. Fisne, I. Alagoz, E. Kaya

Coal produced in underground mines is transported to the surface by means of conveyor belts throughout long roadways. The combustion of belts puts a large number of employees at great risk. Underground collieries differ from other underground mines -due to the combustible nature of the product. The most prevalent cause of belt fires in underground coal mine is spontaneous combustion due to oxidation of the coal, which also enables the conveyor belt to burn over time. In 2014, a belt fire in an underground coal mine in Manisa-Soma, Turkey caused 301 fatalities. A study has been conducted on this accident for approximately 3 years, consisting of combustion tests in a purpose-built research gallery, comparison of the test results with mine records of the accident, and CFD modelling of the mine environment. The intensity of the fire was sufficient to redirect the air flow underground, causin large amounts of toxic gases to fill almost the entire mine in approximately 15 minutes. It is recommended that CFD analysis be used in planning emergency action strategies in underground mines.

Dec 13, 2023

By K. Cole, D. Mesa, P. Brito-Parada, M. R. van Heerden

Turbulence in mechanical flotation cells, achieved via an impeller, plays a key role in keeping particles in suspension, dispersing air bubbles, and promoting particle-bubble collision. However, studying the hydrodynamics of a flotation cell is not a simple task, due to the complex nature of flotation systems which are opaque, turbulent, multiphase and polydisperse in terms of particle and bubble sizes. In this paper we study the impact of impeller design modifications on the hydrodynamics of a continuously overflowing bench-scale flotation tank. To this end, two different impeller designs, with and without a stator, were assessed using Positron Emission Particle Tracking (PEPT). This allowed the authors to determine, for the first time, the effect of an impeller design on the behaviour of both hydrophobic and hydrophilic particle tracers. It was experimentally observed that the use of a stator modifies the hydrodynamics within the flotation cell, distorting the lower mixing loop that is characteristic of axial impellers. The role of the stator in dissipating turbulence results in reduced particle velocities outside of the impeller-stator region. These results have important implications for flotation cell design and are discussed in the context of the impact that different designs have on particle movement, flotation hydrodynamics and, ultimately, flotation performance. The data set generated is also extremely valuable for modelling and validation purposes. Keywords: Flotation, flotation tank, impeller design, rotor, stator, PEPT, hydrodynamics

Jan 1, 2020

By M. I. Mabala, B. P. Watson, M. J. Kanda

A failed and stable Upper Group 2 chromitite pillar database was collected in 2007 as part of the PlatMine 1.2 pillar strength project. The database consisted of 177 pillars, of which 33 had failed. Most of the data were collected from various intermediate-depth mines near the town of Thabazimbi. Spans between rows of chain pillars were about 30 m. Pillar loads were estimated using pseudo-3D, elastic, boundary element modelling software. The pillar-load data were evaluated using a maximum likelihood regression analysis to determine strength parameters, following a similar approach to historically acceptable practice. The original formula was named the PlatMine Formula. This paper describes re-evaluations of the database, using a linear formula and several variations of the power formula. The formula providing the lowest standard deviation to the data in the database was considered the best representation of the pillars in the database. Through this rigorous process, a new formula for peak pillar strength was developed for Upper Group 2 chromitite pillars, which is unaffected by volume. The small standard deviation provided by this formula suggests a reliable relationship between strength and w/h ratio, in the w/h ratio range between 1.5 and 4.7. Accuracy, precision, and recall analysis confirmed the efficacy of this equation to the data in the database. Importantly, the new formula provided in the paper does not predict a significantly different strength to the current PlatMine formula, within the confines of the database.

Nov 27, 2024