Search Documents

By John W. Reddy

The C&NW Ore Dock at Escanaba, Michigan, is a major terminal on Lake Michigan for iron ore pellets arriving from the Marquette Iron Range located 112 km (70 miles) to the north. In an average year, the terminal handles in excess of 8 000 000 Mg (LT) of iron ore pellets consigned to a number of major steel companies. It is important to the steel companies for both cost control and operating efficiency that each cargo be sampled as accurately as possible in order to determine the physical and chemical properties of the pellets. This paper describes the equipment and operating procedures of the sampling facility and Presents some sampling data.

Jan 1, 1985

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By Moussa Wone, Jeff Peterson, Filippo Azzarà, Daniele Nebbia

The DC Water and Sewer Authority's Long Term Control Plan includes tunnels, sewer separation, pumping station rehabilitation and green infrastructure to reduce combined sewer overflow (CSO) discharges to the District waterways. The Northeast Boundary Tunnel is a deep, large sewer tunnel that will reduce CSO discharges; signifi- cantly mitigate known chronic flooding in the Northeast Boundary drainage area and improve the water quality of the Anacostia River. This paper presents the unique combination of Owner and Contractor perspectives of the entire Project from conception through procurement, execution, and contract management, providing lesson learned, chal- lenges encountered, and solutions implemented to deliver the Project successfully.

Jun 23, 2024

By N. Sloan Dworian, Alyssa Smith, Ian Kellogg

Many studies have utilized magnetic susceptibility data to fingerprint porphyry copper centers; however, usage of magnetic susceptibility data to identify trends in a Climaxtype molybdenum porphyry deposit is limited. To better understand potential petrophysical signatures in a Climaxtype Mo porphyry deposit, magnetic susceptibility data was gathered at regular intervals from core holes across the Climax Mine, targeting major lithologies and styles of alteration. Preliminary analysis suggests that there are quantifiable patterns which may correspond with the mineralizing intrusions. This data can complement current mapping and exploration techniques to identify Climax-type molybdenum porphyry centers and likewise further the exploration potential for this deposit type.

Feb 22, 2026

By M. E. Volin

Reagent control for optimum concentrate yield was studied by laboratory batch flotation tests simulating the Groveland plant flotation circuit in which a rougher concentrate is cleaned twice. The reagents were a fatty acid collector, a sulphonate collector and sulphuric acid. The study included two types of flotation feed representative of the reground and deslimed tailing from the spiral concentration circuit, one when the ore mineral is predominantly specularite and the other when it is magnetite. The factorial design included three levels of fatty acid, five levels of sulphonate and five levels of H2S04, with the two types of ore in nested blocks, making up a total of 75 tests. Similarity of results and reproducibility were established in preliminary tests. The final tests were performed in random order under closely controlled conditions following the established procedure.

Jan 1, 1965

By Boyd Eisenbraun, Dennis Murr, Milton Rojas

Approximately since 1925, the phenomena of grinding and classification of minerals with screens have been studied. In the U.S. iron ore mining operations located in the so-called “Mesabi Iron range,” magnetite processing plants have made progress in the application of high-frequency screens that have allowed them to process low-grade Taconite ores and successfully achieve the economic benefit of these minerals. In the particular case of magnetite minerals disseminated in the siliceous matrix, the main objective is to reduce the generation of particles called “middlings” with high silica contents. Commonly the primary challenge of the metallurgical task is to achieve high recoveries and iron concentrates with low impurities. To achieve this, several studies and industrial applications have shown success in this regard and not only in iron ores, but also in other minerals around the world. The study described in this paper attempts to describe some key aspects that helped develop an effective solution and list the benefits associated with this modern process design by using industry-proven technologies for minerals in Chile that have similar characteristics to the minerals of the iron belt in the United States.

Feb 1, 2025

By D. C. Seidel

The role of surface charge in soluble salt flotation, which was developed in Part 1, is extended to relate the theory to the specific phenomena of KCI- NaCl separations. Temperature-collector solubility relationships, metal ion activation, and particle size effects are discussed.

Jan 1, 1967

By Shiou-Chuan Sun

Notwithstanding the fact that unsaturated fatty acids are used in preference to saturated acids for most flotation purposes, information regarding their collecting properties is sketchy. Keck, Eggleston, and Lowry1 reported in 1939 that the collecting power of fatty acids on hematite decreased in the order of oleic, lauric, myristic, palmitic, and caprylic acid. Keck and Jasberg2 described in the same year that "unsaturated oleic acid with 18 carbon atoms was a better collector than saturated stearic acid" for floating magnetite. Gaudin and Cole3 stated in 1953 that the double bonds of oleic and linoleic acid were not oxidized during the flotation of fluorite, whereas the double bonds of linolenic acid were measurably altered even after one single flotation step. In August, 1953, Hukki and Vartiainen4 concluded that the collecting power of palmitic, oleic, linoleic, and linolenic acids on ilmenite, magnetite, pyrite, and rutile increased with an increasing number of double bonds in the acid molecules. This was subsequently proved to be generally true for the flotation of mapganese5, phosphate6, and magnetite7. The above cited literature indicates that, prior to the present paper, only about ten minerals were tested with pure unsaturated fatty acids as collectors.

Jan 1, 1959

Microorganisms have been widely used for hydrometallurgical operation and effluent treatments(Smith, et. al., 1991a; Gadd, et. al., 1986; Darnall, 1986; Paponettis, et. al., 1991; Mihaylov, et. al., 1991; Rusin, et. al., 1991; Noble, et. al., 1991; Yang, et. al., 1991). In recent years there is a growing interest in using microorganism for flocculation of minerals fines and flotation collector (Smith, et. al., 1991b, 1991c; Misra, et. al., 1991a, 1991b, 1992a, 1992b). It is envisioned that the utilization of nonpathogenic microorganism and/or extracellular surfactant derived from microorganism as a flotation collector will replace some of the environmentally toxic flotation collectors and at the sometime improve flotation efficiency. The selection screening, and judicious selection of appropriate microorganism as flotation collector has been a challenge to process engineers. Over the past five years, continued research at the University of Nevada has shown that certain microorganism Mycobacterium phlei (M. phlei) can be a good flocculating agent and has potential to be used as a flotation collector (Dubel, et. al., 1992; Misra, et. al., 1991a, 1991b, 1992a, 1992b; Smith, et. al., 1991d; Chen, et. al., 1992a, 1992b)).

Jan 1, 1993

By George A. Snyder

The presence of moderate to high concentrations of colloidal clays in coal preparation plant waters can cause serious operating and economic problems for a coal company. Among the host of possible problems are the following: 1) Poor separation of clays in the plant thickener, resulting in: a) Increased ash in the clean coal. b) Increased specific gravity of the wash water and decreased coal recoveries at the desired quality. c) Increased thickener operating costs in trying to overcome the problem. 2) Decreased solid concentrations in the thickener underflow and increased pumping requirements to meet solids withdrawal requirements.

Jan 1, 1979

By A. Noble

For the past 30 years, process flowsheet design has been accomplished largely through modeling and simulation. This approach provides circuit designers the freedom to test various separation approaches while minimizing physical and human resource requirements. The Limn® software provides a unique approach to process simulation, through a Microsoft Excel interface. While the software comes with standard process models for numerous unit operations, the Excel calculation environment and the accompanying VBA platform provide a convenient interface for custom model integration, even for non-experienced programmers. This feature is especially useful for university students in introductory process modeling and simulation-assisted flowsheet design courses as well as experienced practitioners with proprietary process models. This paper shows how the Limn® software may be used to solve basic process engineering problems as well as more comprehensive circuit design challenges. Industrial examples as well as opportunities for training and education are presented.

Feb 23, 2014

By H. Melama

The primary grinding stage in the Vuonos concentrator comprises a rod mill in open circuit and a semi-autogeneous mill in closed, circuit with a hydrocyclone classifier. The instrumentation of the grinding circuit is displayed in Fig. 1. All the measurements have computer interfaces and all the control circuits have been implemented by the process control computer. The crushed ore feed to the rod mill is measured by a belt-weigher and controlled by a belt-feeder. The pulp density in the rod mill is stabilized by proportioning the waterfeed at the mill inlet to the crushed ore feed. The slurry level in the pump sump is measured by a pressure transducer and it is controlled by charging the speed of the direct-current drive pump.

Jan 1, 1984

By M. Adnan Goksel

The hydrothermal agglomerating process described (U.S. Pat. 3,235,371, (1966)) is different from the conventional high temperature processes. Green pellets or briquettes made with mixtures of moist iron ore concentrates and burned or hydrated lime fines are hardened in an autoclave at 198°C and under steam pressure for 1/2 to 5 hours, with or without previous drying. Under the neutral conditions, oxidation of magnetite does not occur as in the conventional processes. The resulting agglomerates are hard and resistant to abrasion and weathering, and they do not disintegrate in the Linder test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperature and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1968

By B. Qiu, Y. Luo

The design of the predriven recovery room is not an easy task, because the stress distribution in the barrier pillar, standing supports, fender pillar and the immediate roof is changing as the longwall face approaches the predriven recovery room. An analytical approach is proposed to determine the stress distribution in the barrier pillars, fender pillars, standing supports and immediate roof of the recovery room based on the fracture mechanics approach. Based on the developed mathematical model, a stand-alone computer program has been developed to facilitate the required computations. The parameters such as overburden depth, recovery room width, mining height, shield and standing support capacities are incorporated into this program to access the feasibilities of predriven recovery room designs. Compared to the finite element method previously employed, this analytical approach offers the same, if not better, accuracy without requiring expensive computer hardware and software or specialized expertise.

Jan 1, 2012

By C. Patrick

Longwall face-to-face transfers can cost over $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high cost makes extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. This paper reports operations research techniques used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate over 30% of the total U.S. longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation models of transfers under varying conditions were generated; and, the economics of general transfers and time-cost tradeoffs in the transfer procedure were investigated.

Jan 1, 1993

Due to the ongoing restructuring of the mining industry in central Europe with a continuous decline of the number of large underground mines and collieries, and a simultaneous decline of staff numbers in the remaining mines, the established mine rescue schemes are endangered to collapse. With the end of the mine rehabilitation at Wismut Uranium in 2014, the last remaining major mine rescue teams in Saxony, providing basic mine rescue services for all other mines in the region, will disappear. This will leave a large number of small mines and other underground operations without capable mine rescue support. Since none of these companies is able to set up a complete mines rescue unit on its own, new ways have to be found. Among others, a central mine rescue team for central Germany as well as the assistance by special trained professional fire fighters or mine rescue teams from abroad are discussed. Problems like location of the central rescue team, financing, communication and transport have to be solved. This paper provides an overview over the complexity of the problem as an example for other mining regions worldwide and will discuss national and cross-national strategies.

Feb 23, 2014

By Philip A. Bucci

The Florida phosphate industry successfully uses froth flotation to concentrate phosphate in: the particle size range of approximately 28 to 150 mesh. However, as recently as 1965, coarse particles in the range of 14 to 28 mesh generally had not been beneficiated by conventional flotation methods at recoveries high enough to be considered adequate. It has been customary to upgrade this coarse material; by "agglomerate flotation" or "skin flotation" using belts, tables or spirals. While these devices have proved commercially effective, their capacities are much lower than those of froth flotation cells. To determine whether coarse phosphate material could be recovered successfully by froth flotation, Armour Agricultural Chemical Company began a series of pilot and plant tests; in April 1965. Objective of the tests was to compare over-all performance of a froth flotation cell design relatively new to the phosphate industry with results from the belt circuit at the Bartow, Fla., plant.

Jan 1, 1966

By H. Vigil Fernandez, G. Peach

The Musaimeer pump station and outfall project located in Doha Qatar, was designed to collect and manage ground and stormwater and then discharge the treated waters offshore. The project constructed a long outfall tunnel using an EPB TBM with segmental lining, each tunnel ring being 1.35 m in length with an internal diameter of 3.7 m.. The diffuser structure was a 6-arm structure, measuring 294m by 40 m connected to a central manifold in turn connected to the TBM constructed tunnel via a riser shaft drilled from an off-shore barge. This technical paper will discuss the planning, methodology and construction practices employed to connect the TBM tunnel to the diffuser structure 10.2 km offshore.

Jun 13, 2023

By Peter I. Brooker

The semi-variogram, the basic tool of geostatistical estimation procedures, must itself be estimated from the available data. From a numerically simulated two dimensional deposit, with known variability expressed through its semi-variogram, the standard arithmetic mean estimator is used to calculate experimental semi-variograms. These are determined on a series of data sets obtained from the deposit with various sampling grids which cover different areas of the deposit and which have a wide range of available data. The orders of discrepancies between estimated and theoretical semi-variograms are determined in this idealized situation; and this provides a basis against which to assess experimental semi- variograms made on field data.

Jan 1, 1982

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984