Search Documents

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018

By Jeremy Stone, Yiming Sun, John Stolz

The Courthouse Commons Tunnel facilitates the secure transfer of inmates between the County Jail and State Courthouse across a city block in downtown San Diego, California. This shallow tunnel was excavated using the Sequential Excavation Method in soft ground. It passes under 8- and 10-story buildings with a foundation cover of 6 feet, and crosses the active San Diego Fault with a design offset displacement of 18 inches. In this paper, key design challenges of tunnel construction are presented: limiting building settlements without using underpinning of building foundations and incorporating an oversized seismic section with seismic joints and crushable backfill

Dec 1, 2022

By A. Toulet

Mining in Mexico has an immensely long tradition. In his first letter reporting to his sovereigns from Mexico in July 1519, Hernan Cortes wrote, "To our mind it is probable that this land contains as many riches as that from which Solomon is said to have obtained the gold for the temple ... " 1 But not only precious metals drew his attention; in 1524, short of tin needed for casting guns, he found it in Taxco. As an added bonus, those who went to find it "came upon a vein of iron which according to experts is of exceeding richness." 2 Since then, the mines of Mexico have yielded up enormous amounts of mineral and continue to do so. Mexico is one of the ten principal producers of minerals world-wide both in production volume and diversity. 3 Tens of thousands of tons of iron, sulphur, and coal come from its earth annually; it is the world's second largest producer of barite; third of antimony, fluorite, and graphite. 4 Copper, zinc, silver, molybdenum, arsenic and cadmium and others are wrested from its mines. The wealth is there; but maximizing its potential requires investment, technology, and markets that the government cannot itself provide. Thus mining, since the Mexican Revolution severely restricted by both law and policy, today looks to private investment to develop its potential. Beginning in 1989, Mexico's government cautiously moved to liberalize private sector involvement in mining; 5 using the experience gained from these initial regulatory changes, the current new Mining Law was adopted in 1992 6 and new Regulations were promulgated in 1993. 7

Jan 1, 1994

By Robert W. Leonardson

The Questa Molybdenite Mine provides a unique opportunity to study the geochemical dispersion of various hydrothermal events, utilizing drill hole analyses. Numerous post-ore factors have altered the primary ore-related geochemical dispersions to the present day configuration, e. g. dikes, faults, hydrothermal convection cells, and weathering. Due to the interaction of an andesitic volcanic pile with the silicic-alkalic generated volatiles, the geochemical haloes of the Goat Hill deposit demonstrate a marked divergence from the classic Climax-type molybdenite ore body. Certainly, however, the similarities to the Climax-type ore body are apparent as potassically-rich fluids have invaded the highly reactive country rock.

Jan 1, 1984

By B. L. Bobo

To ensure the continued growth and economic viability of the Western coal industry, both in the domestic and inter- national markets, it is essential for the industry to become more creative and active in confronting the most serious obstacle in this objective; and that is, the inherently long distances which Western coal must be transported inland to reach its major markets. Figure 1 shows the 1982 coal consumption by state for those states where Western coal was consumed. (Except as noted in this paper, Western coal producing states are defined as Colorado, New Mexico, Arizona, Utah, Wyoming, Montana and North Dakota. Any exceptions used will have only an insignificant effect on the content of the paper). This figure illustrates the long distances that are required for Western coal to reach its markets. The total production for 1982 from the Western coal producing states was approximately 220 million tons, of which only 85 million tons was consumed within the boundaries of these states. The remainder was transported to markets outside the area. This map also shows, based strictly on the consumption of the states to which Western coal was shipped during 1982 and not considering other factors which are involved in the marketing of coal, the total market potential of Western coal would amount to a total of 445 million tons. This does not include export coal from the West Coast, which is now estimated to be less than 2 million tons for 1983. In 1980, it had been estimated that by 1985 the West Coast exports would have been at least 10 million tons per year, which will not be attained.

Jan 1, 1983

By R. W. Lake

The decision to develop an ore body can lead to multi-million dollar profits, or equally substantial losses. Accordingly, the effort required to adapt a valuation model to the specific proposal at hand, or even the development of a new model from basic principles, is clearly warranted. In the formulation of a model of this nature, one is faced with some major questions. For example, with the long term obligations that it implies, on what basis should a decision to initiate mining operations be made? Furthermore, how can the vagaries of inflation and the uncertainties that shroud the future be accommodated? Beyond the general principles by which mineral deposits are evaluated, specific cost behaviour is a function of the geology of the deposit, and of the mine design. Moreover, mine design, during the life of the mine, must be a continuing process somewhat akin to dynamic programming. An initial, apparently optimal, design is selected and mining commences. With production, a continual process of information updating leads to revisions. Thus if the maximum value is to be obtained, the mine design must be adjusted to conform to the changed conditions.

Jan 1, 1977

By Charles S. Spirakis

The consistent occurrence of organic carbon early in the paragenesis of Mississippi Valley-type sulfide deposits suggests a genetic link between organic carbon and the sulfide ores. Reduction of sulfate in the mineralizing solution by organic carbon at the sites of mineralization is commonly proposed as the precipitation mechanism for these deposits, but inorganic sulfate reduction is too slow to be important to the chemistry of the ore zone, and bacteria, which catalyze sulfate reduction at low temperatures, are not known to survive at the temperatures of mineralization. Sulfate reduction with or without bacteria is not consistent with the sulfur Isotope evidence. Sulfur isotope studies also indicate that the derivation of sulfur from hydrocarbon at the sites of mineralization is unlikely. Organometallic complexing may be involved in the transport of metals, but no plausible mechanism for breaking these complexes at the sites of mineralization has been proposed. Reduction of partly oxidized sulfur species in the mineralizing solution by organic carbon at the sites of mineralization is a possibility which deserves further scrutiny.

Jan 1, 2013

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

According to the Balandin's (1) "multiplet theory of catalysis", adsorption can occur only if atoms of the reactant molecules are congruent with surface atoms of the catalyst. Such a condition calls for certain definite geometrical relationships between the reactant molecules and the atoms at the surface of the catalyst. If such a match or geometrical 'fit' is not provided, the surface reaction will not take place. An appropriate analogy to this may be the lock and key theory that enzymes should fit a substrate just as a key fits a lock. Similar geometrical considerations in adsorption studies were made in connection with the flotation of minerals. Gaudin(2) and Gaudin and Preller (3) proposed that if the dimensions of collector ions are in registry with the mineral lattice, an ordered layer of adsorbed species is formed. They explained that the structural fit is one reason for good flotation of galena with xanthate. In another study, Bachmann (4) attributed the selective flotation of KC1 from NaCl with amine to the fact that the lattice parameter of the amine collector is closer to that of KC1. Schubert(5) investigated the flotation of various nonmetallic minerals with amine and pyridine, and related the dimensions of the collector ions with the anion distances of the mineral surface. He concluded that good flotation is obtained when the tolerance is within 20%. The geometrical theory has also been used by Groszek (6) to explain the preferential adsorption of n-paraffin onto the basal plane of graphite. The geometrical theory has thus been found useful in explaining adsorptive properties of an adsorbate relative to the substrate structure. The purpose of the present work is to examine the possibilities of a geometrical fit between sodium dodecyl sulfate and Cu(OH)2 surface, and to construct a crystallographic model of the surface compound.

Jan 1, 1974

By Francesco Chiappalone, Miriam Piemontese, Lance Waddel, Paolo Perazzelli, Emidio Tamburri, Roberto Schuerch

The Three Rivers Protection & Overflow Reduction Tunnel is part of the Long-Term Control Plan of the City of Fort Wayne, Indiana (USA). The 4.9 m internal diameter tunnel, of length approximately 7.5 km, is excavated at a depth of approximately 40–60 m through carbonate rocks using a slurry TBM. Due to the high hydraulic conductivity of the rock mass and the high in-situ ground water pressure (up to 6.5 bar), the management of the water inflow during the TBM advance and standstills, represents the major challenge for the project. This paper outlines the geotechnical conditions and the hazards related to the large water inflows expected in the pre-excavation phase and discusses the experience gained during the construction of the first 8,224 feet (2,507 m), (first third of the total length of the tunnel).

Jun 13, 2021

By Craig E. Burson

This paper discusses the relationship between frother types and coal flotation as a function of particle size. It has been found that each frother has a unique size fraction that it will float effectively. This fact is very important when it comes to selecting a reagent scheme that will provide maximum recovery of both coarse and fine particles. Improvements in recovery can be attained when the chemical relationships between frother type and particle size floated are understood. Data from plant evaluations using commercial and developmental frothers are presented to verify the importance of frother types versus size fraction floated.

Jan 1, 1987

By S. G. McDowell

This paper discusses the utilization of automation to increase productivity of continuous miners. Automation techniques are used during the design stage to decrease the time required and ensure the accuracy of the design. This is followed by automated manufacturing processes to reduce manufacturing time and improve the quality and consistency of parts. Combined, the result is a more reliable machine which can provide ongoing production capability. With the use of automation to enhance operator effectiveness and monitoring machine condition the productivity of machines is also improved.

Jan 1, 1991

By Joseph A. Whitchurch

The N20 to N25 Tunnel (basic) segment was the second tunnel contract awarded for construction by The PB/MK Team. This project embodied 3.9 km (2.4 miles) of tunnel and was located within the northwest quadrant of the 86.9 km (54 mile) long main collider ring. The contract required the excavation and initial support of a 54.3 m (178 vlf) deep ventilation shaft, a connecting horseshoe shaped Adit and TBM starter tunnel and 3,865 m (12,680 If) long main collider tunnel with a 4.3 m (14 ft) minimum finished diameter. This paper discusses the construction methods, equipment utilized and the production achieved in the construction of the ventilation shaft, connecting adits and the main collider tunnel.

Jan 1, 1995

By M. D. Ross

Complex combinations of technical, economical, safety and environmental factors are causing mining engineers everywhere to review their operations. Naturally, some of the traditional methods still have a large role to play because they are, in certain circumstances still adequate and are well understood. But, as circumstances change, a new approach is required. The combination of technical and economical reasons for introducing Long- wall mining in some seams in the United States is associated with strata control. Other reasons include simplifications and improvement of ventilation, reduced coal dust, more output from each unit and crew, increased percentage of recovery from each area of the coal deposit, and reduction of rock dusting. The innovations which transformed Longwall mining from a cyclic to a continuous mining system were the armored conveyor and power loading machines, but the crucial breakthrough for application to high production was the development of the powered roof support, which at once gave the system the advantages of mastery of strata control, increased rate of advance, significant reduction of manpower, and increased safety.

Jan 1, 1974

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By R. Hogg

Experimental studies of the axial distribution of particles along dry ball mills are described. The results, for mills ranging in diameter from about 10 cm to 1 meter and operated in both the batch and continuous modes, indicate a consistent pattern of significant migration of particles away from the ends of the mill. In some, but less frequent, cases axial migration of the grinding media is also observed. Analysis of the data suggests that particle migration results from end-effects which extend for a distance of about one mill diameter along its length. End-wall roughness appears to play a significant role in the particle migration phenomenon. Media migration is generally associated with continuous mills operating at relatively high powder flow rates.

Jan 1, 1994

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994

By German Zambrana

The solution of the problem of beneficiation of cassiterite from its primary ore deposits is of fundamental importance to Bolivia. The process today involves a gravimetric treatment of the ore followed by sulphide flotation. During the last year, a cassiterite flotation stage has been added in several plants to treat the slime tailings. Although cassiterite flotation is already economical for the slime tailings and the mechanism of the process are understood, it is felt that further research could improve the results. In the past, considerable amount of research and test ark has been performed to select appropriate collectors to improve recovery, to increa¬se the grade of tin in the concentrate, to minimize the effect of metallic ions like Ca+2, Fe+2 and Fe+3 which prevent flotation, and to increase the pH of the pulp which now it can not be higher than 3.0. It has been reported that the halogen salts (1) like NaCl exhibit special surface affinity for cassiterite but none for quartz. These effect seems to be favourable for the selective flotation of cassiterite from silica minerals. In view of these preliminary results it was decided to follow the research accordingly: OBJECTIVES The objectives of the present investigation are: 1. 0 evaluate the influence of NaCl salts in quartz and cassiterite flotation.

Jan 1, 1971

By H. W. Newcomen, D. R. Brox

Assessments of the stability performance of open pit highwalls have traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work have been reviewed and are generally endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on the observed trends in highwall strain data from the case histories presented.

Jan 1, 2004