Search Documents

By J. MCGUIRE, E. J. Haas, B. Demich

Near misses can enhance awareness of the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, the value of these reports and how they influence subsequent actions or controls to reduce on-the-job risks are unclear. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. The analysis provides insight into ways that risk-communication and management programs can be improved to reengage workers and their situational awareness on the job.

By R. C. Gilmore, S. A. Lolon, G. E. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Gob ventilation boreholes (GVBs) are widely used in underground coal mines for longwall gob degasification purposes. GVBs are often drilled within 10 to 30 m above the top of the coal bed into the fractured zone, completed with 20 cm (8 in.) diameter casing and 60 m of slotted pipe at the bottom. The purpose of this completion strategy is to create a pressure sink to capture the emissions before they can enter into the underground workplace. For GVBs to work effectively, they must be drilled close enough to the working areas to capture methane from the fractured zone while the setting depth must be kept above the caved zone to minimize the amount of ventilation air that is drawn into the GVBs. Well completion parameters are important for creating safe working conditions. In this paper, computational fluid dynamics (CFD) studies will be presented to analyze the effect of different practices for GVBs completion parameters for methane extraction, formation of explosive gas zones in the gob and methane concentrations at the longwall face and tailgate. Authors have identified the optimum completion parameters for GVBs, which can maximize the benefit and minimize fire and explosion risk. INTRODUCTION Coal mines may be considered gassy based on the presence of CH4. Gas from the mined coalbed or from rider seams above or below the mined coalbed can migrate into the gob and then potentially move towards the working areas. In longwall coal mines with high methane emissions, sufficient ventilation and additional methane control measures are usually required to reduce the methane concentration in working areas to below statutory levels. Several techniques or combinations of techniques are available to control the methane hazard. These may include mine face ventilation to dilute methane, coal bed degasification, nitrogen injection into the gob to render a methane atmosphere inert and the use of gob ventilation boreholes (GVBs). Longwall face ventilation and dilution alone can only handle methane emissions up to a certain amount. When methane emissions exceed the face ventilation capacity, additional control measures are required. Drilling horizontal or vertical methane drainage holes into the coal seams as well as gob ventilation boreholes from the surface into the gob area to extract methane are common practices. GVBs are usually drilled from the surface above the longwall panel ahead of mining. When the face moves outby the GVBs and the gob begins to form, methane production starts from the boreholes. It is important to control the performance of GVBs to maintain a safe working environment in the mine. The performance of GVBs depends on multiple factors, including borehole location, length and diameter of slotted casing, setting depth of casing above the coal seam being mined, wellhead vacuum pressure, and permeability of caved-fractured zones."

Jan 1, 2016

By Errol L. Montgomery

The region of metalic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 4,600 meters. Because surface water supplies are meager, new mines require unexploited sources of water. Prolific groundwater aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate groundwater quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum production water well capacities in excess of 170 liters per second.

Jan 1, 1982

By E. Watkins, S. J. Schatzel, V. Gangrade, R. Kimutis, J. Addis, C. Hollerich

The recent shale gas revolution in the United States has led to the drilling of hundreds of unconventional shale gas wells in active and future coal reserves in traditional coal-mining regions of Pennsylvania, West Virginia, and Ohio. This paper summarizes the impact of a shale gas well breach on the mine ventilation system of an operating longwall panel. This study utilizes a 1:30 scaled Longwall Instrumented Aerodynamic Model (LIAM) to simulate a single-panel longwall operation. The LIAM will be utilized to identify flow pathways and distribution patterns of gas from breached gas well scenarios in an operating longwall in the Pittsburgh Coal Seam. Sulfur hexafluoride (SF6) tracer gas is utilized to simulate a breached gas well. Preliminary findings suggest that the breached gas is diluted to regulatory levels and does not accumulate in the mine entries or in the longwall gob when the longwall panel is adequately ventilated. Overall, this study characterizes the potential interaction between shale gas wells and the mine environment in the event of a gas well breach, which provides critical information to the industry and regulatory agencies for improving safety, health, and welfare of miners.

Mar 2, 2022

By Charles Dumaresq

The management of mine tailings poses a complex range of potential risks, including physical risks, such as the risk of catastrophic failure of a tailings facility and chemical risks such as the risk of long-term leaching of contaminants into the downstream environment. If these risks materialize, they can lead to a wide range of impacts on people and the environment, including human fatalities and severe impacts on downstream ecosystems, and the costs of recovery borne by industry, communities, governments, and society as a whole can be immense. Tailings facility failures in Canada (2014), Brazil (2015 and 2019), South Africa (2022), and in other locations around the world underscore how high the stakes are when mines produce and manage tailings (WISE Uranium Project 2019). Understandably, many people do not trust the mining industry to manage tailings responsibly. As an industry, it is our responsibility to manage tailings in a manner that is responsible and strives to minimize harm associated with tailings management, including effectively managing both the physical and chemical risks associated with tailings. Standards have an important role to play in responsible tailings management by setting expectations for standards of care and providing a means to measure and report on performance. In jurisdictions with strong legal requirements for tailings management, standards play a complementary role, pushing performance improvements in areas that may be difficult or impossible to address in legal requirements. In jurisdictions where legal requirements are lagging, standards may represent the de facto leading practice and may be the primary tool to help ensure responsible tailings management. Implementation of standards can help companies demonstrate that tailings are being responsibly managed and help build trust and credibility. Most importantly though, standards are important tools to help ensure that the risks associated with tailings are reduced, and that remaining risks are effectively managed. However, we must recognize that conformance with standards can have a down-side – the proverbial two-edged sword. Having standards is vital but there is a risk that implementing standards becomes a “box checking” exercise, with ongoing conformance leading to complacency. We must not allow ourselves to fall into the trap of believing that, just because we are complying with applicable standards and laws, we are therefore doing our best, and that “it can’t happen to us.” In addition, if conformance becomes the goal and the standard does not have mechanisms to drive continual improvement, then once the standard is met, there may be no incentive to improve. The point of complying with standards is not to pass the test. The point is to manage tailings responsibly, prevent catastrophic failures, and minimize harm. The point is to do better, because we must do better. To do that, we need to strive not for conformance, but for excellence in tailings management, driven by continual improvement and a quest to do better.

Feb 1, 2025

By Richard L. Sanford

This paper summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory is funded by the U.S. Bureau of Mines and includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. General references to computer applications throughout the mining industry are discussed as well as the availability of programs to interested organizations or individuals.

Jan 1, 1978

By Robert Bohman

I truly free enterprise system requires free and unrestricted competition among a diversity of suppliers, in order to function properly. The natural attrition of the marketplace tends on the one hand to narrow the competitive field ... but the flow of new competitors entering the arena provides a "diluting" effect, and a "balanced" market place. Without the ready flow of new business entrants, the market becomes increasingly concentrated in the hands of fewer and. fewer firms. Competition among suppliers is diminished and the "free" marketplace suffers accordingly. A number of organizations, both governmental and private, have recently expressed grave con¬cern over the competitive future of the Western coal market. While most have noted that there is currently adequate competition within the Western market, some have cited the growing con¬centration of coal ownership ... particularly federal lease ownership ... in the hands of a relatively few firms. They suggest that unless this apparent trend is reversed or at least stemmed, the number of new firms entering the federally-dominated West may become reduced to the point where competition will suffer.

Jan 1, 1982

By Peter G. Chamberlain

The Bureau of Mines is conducting research to boost domestic production of manganese. Virtually no mining exists in the low grade and/or small deposits that occur in this Country. One large, low-grade manganese deposit located in westcentral Arizona--The Artillery Peak district--was extensively studied and sporadically mined during the 1940's and 1950's. Although manganese mining in the district has been long dormant, recent studies indicate that the deposits may be amenable to economical production by heap and/or in situ leaching methods. A conceptual design for an in situ leaching system features undercutting and blasting a block of ore, leaching with SO2, and extracting the manganese as a sulfate or oxide. Possible applications to other manganese deposits depend upon formation permeability and specific manganese mineralogy.

Jan 1, 1981

By Tristan Joubert, Fabio Panella, LiLing Chen, Yung Loo, Michael Devriendt, Nasir Qureshi, Ahmad Ali

Tunnel inspections have traditionally been carried out manually by inspectors writing up observations and taking photos of defects. The results from the inspection and the defects observed are dependent upon the rigor of the inspectors and may be subject to repeatability and consistency issues and is often time consuming with elevated health and safety risks. This paper will discuss work that is being carried out in developing and implementing an innovative hardware and software solution integrating machine learning to automate the process of capturing objective tunnel condition information, offering cost and programme savings as well as health and safety improvements

Jun 13, 2023

By T. Lee

Ongoing economic success for mining companies is dramatically enhanced when they really know what they are harvesting, such that they can accurately forecast their head grades for any time period in excess of a month. This is an uncommon experience. It is a very common scenario for resource/reserve estimates to overstate the concentration (grade). Grade is a critical input of revenue, and hence, it is to cashflow projections. With the current direction being taken by the legal climate, it is no longer adequate for directors to accept the resource/reserve estimates of experts at face value. This is because resource/reserve estimates are the foundation of primary mineral economic decisions. Directors of mining assets need to undertake their own due diligence analysis of these estimates, in the best interest of themselves, and the company's shareholders. In the light of the industry's past achievements, this is quite a challenge. This paper suggests a set of new objective tools for directors to undertake an overview of the unique commodity concentration pattern and assess associated economic dynamics of each mineralization. These tools allow the examination of global graphical trends that can be helpful to directors and others in undertaking due diligence of resource/reserve statements. Ensure that it smells right.

Jan 1, 1995

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

As indoor positioning provides particular challenges due to the unavailability of GPS signals, various systems such as ultrawideband (UWB), radio frequency identification (RFID), ultrasound, and wireless local area network (WLAN) have been proposed in recent years. Some of these technologies are currently being marketed and some are still being developed. UWB technology allows for higher precision while also reducing power consumption. Hence, the underground automation and localization systems can use this technology for more accuracy and robustness. This article discusses new robust UWB modules used for underground positioning and collision avoidance with regard to human safety in underground mining operations.

Jul 31, 2020

A portable electronic instrument was developed which will measure change of longitudinal wave velocity with change of uniaxial stress in rock columns. The instrument is a solid-state device powered by nickel-cadmium batteries. It uses a probe of two piezo-electric crystals spaced inches apart to send and receive a pulse through a stressed rock. A one-inch cathode ray oscilloscope visually displays the longitudinal wave. A reference chart is used to find the stress. Laboratory results have indicated that the average stress on a sandstone column can be found to within 35 psi. The feasibility of using this instrument to determine stresses in mine pillars is to be studied. The instrument may be used to investigate physical properties of rock.

Jan 1, 1970

By J. Le Gac, P. Zettwoog, J. Brenot, J. W. Piechowski, J. C. Nenot

INTRODUCTION The components of the radiological hazard in uranium mines are: 1. exposure to radon and its short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation With usual ventilation rates, the dosimetry relative to the first component only requires to know each miner&apos;s exposure to a potential energy of short-lived radon daughters, (EXP[a]). Presently in France, (EXP [a]) is determined monthly from radon concentration measurements. This is an indirect method based on ambient monitoring. After technical improvements achieved during the last years it is now possible to measure (EXP [a] directly with an individual portable monitor developed by the CEA. The purpose of this study is to analyze and compare monitoring results obtained by these methods. DETERMINATION OF INDIVIDUAL MONTHLY EXPOSURES TO[ a] POTENTIAL ENERGY OF SHORT-LIVED RADON DAUGHTERS [(EXP a) amb, by ambient monitoring] In this case, it is necessary to know individual monthly exposures to radon, (EXP Rn). As mentioned by Pradel, J.,et al., 1976, (EXP Rn) is estimated for each worker from informations both on radon concentrations (CRn) measured as described by Pradel, J., 1962 and times (t) elapsed in the various workplaces. (EXP Rn) is obtained by summing up the elementary radon exposures CRn x t relative to all the workplaces where the miner was successively engaged during the month. (EXP Rn) values are then corrected by an average equilibrium factor of 0.17 deduced from many measurements and taken as representative for all the French mines. Finally: [ ] (EXP [a])ind are obtained directly with an individual portable instrument described by Chapuis, A.M., et al., 1972. Samples of the air breathed by the miners are pumped continuously and radioactive aerosols containing the short-lived radon daughters are trapped on a filter. The principle of the measurement lies on track-etch detection of the a particles emitted by the deposited material. The technical aspects have been described by Duport, P., et al., 1980a, Mouden, A., et al., 1980 and Chapuis, A.M., 1980. As mentioned by Duport, P., et al., 1980, fiability is good. Indications on measurement reproducibility are given by Pradel, J., et al., 1977. PRESENTATION OF THE STUDY The underground miner population of a French mine was followed during a period of 8 months (October 1978 - May 1979). Monthly exposure values for each miner determined either by ambient or individual monitoring, (EXP [a])amb or (EXP[ a])ind, had been previously collected by Le Gac, J., 1980, who had also defined miner categories according to the characteristics of the work performed. Four groups are considered here, the "whole mine" and three categories as described in table 1. Data on the individual monthly exposures,(EXP [a])ind and (EXP [a])amb, were taken again to analyze the individual cumulative exposures instead of the "month by month" values. The influence of the mean habits of each individual on its surveillance results is thus taken into account. Each miner has a cumulative exposure as an individual of the "whole mine" and as an individual of each category in which he has worked. The results obtained by ambient or individual monitoring were analyzed (characteristics and adjustements of the distributions) and then compared (description of the discrepancies observed). Obviously, such a study is possible only if all the exposures are cumulated on a same duration. As miners have not worked during the same number of months in the course of the data collecting period, one must considerer the individual average monthly exposures, [(EXP a)]amb and[ (EXP a)]ind, instead of the individual cumulative exposures, which is typically the same thing. To be sure that the exposure values of a given group (A, B, C or D) are representative, only those miners really present for at least 3 months in this group were taken into account. Finally, each individual of the "whole mine" and of the various work categories has a pair of average monthly exposure values : [(EXP a)amb] determined by ambient monitoring and[ (EXP a)ind] deduced from the track-etch recording of the individual portable monitor. Let a miner be engaged during n months[ (3 < n < 8)] in a group, the following relations then apply : [ ]

Jan 1, 1981

By M. Y. Fisekci

Subsidence measurement methods, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada are described. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suited methods for our conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the network of laser surveying over the workings of the new hydraulic mine. The site particulars and the mining method of the concerned area have been described briefly. The observation over the old hydraulic mine indicate that panels adjacent to each other do not obey identical subsidence phenomenon.

Jan 1, 1982

By T. Fernandez, V. Juchen, C. Petter, F. Cantini, V. Lenz, V. I. Araújo, R. Petter, R. Darrigo, A. Young, I. G. da Costa, J. Oppermann

There are many methods to estimate costs quickly. One of these is the Parametric Method, where costs are estimated from general algorithms (or curves). Derived from an original tool based on the O’Hara model, a software called MAFMINE was developed. MAFMINE is based on parametric models to estimate investment and operational costs in mining. The software itself is based on the use of a computer model known as client-server. However, the model needs new inputs from advances made by the mining industry, mainly in terms of electrification, automation, digital transformation and preconcentration to face Environmental, Social and Governance (ESG) concerns. Thus, this work was to prepare a new core module ready to incorporate the new technologies aiming to deliver operation and capital costs associated with environmental impact mitigation. The tool generates an order of magnitude estimate for CAPEX and OPEX to establish a very first Discounted Cash Flow (DCF) in a mining venture. For quick evaluations, at a preliminary level, the results are very promising.

Mar 2, 2022

By Juan C. Diaz, Juan P. Carmona, Manuel Z. Salgado, Oscar J. Restrepo

The “Teaching Kids” project is an educational initiative for young people and children from elementary schools. It is carried out by Mining, Geological, and Environmental Engineering students from the SME Student Chapter of the Universidad Nacional de Colombia, Medellin. The primary purpose of the Teaching Kids project is to share knowledge about geosciences and mineral resources in a didactic and attractive way, emphasizing the importance of identifying the use of minerals in daily life and responsible and sustainable mining in our society. Furthermore, this project aims to promote the importance of pursuing geoscience majors in the new generations and improve the mining industry’s public perception. Different methodologies related to early childhood education are implemented, such as gamification, in which the dynamics of games are adapted during the development of workshops to teach and learn in an active and motivated environment. Furthermore, the Montessori Method is used. It implements textbooks, sensory mineral boxes, and presentations to allow learning through experimentation itself (Montessori 2003). The implementation of this methodology has been successful; it has shown high engagement, participation, and retention of the basic concept of geoscience and mining.

Feb 1, 2025

By Dávila-Pulido. G., L. Magallanes-Hernández, F. López-Saucedo, J. Batista Rodríguez, A. Uribe-Salas

"This paper presents the results of tests performed to study the effect of slurry solids concentration on the behavior of gas dispersion in industrial-scale mechanical flotation cells. The experiments were conducted at five concentrator facilities run by a Mexican mining company, specifically in the rougher bank of the lead/zinc flotation circuits. Those mechanical cells having significant contribution to the performance of the circuit, that is, the cells that enable high recovery, were characterized. The measurement protocol enables measurement of the superficial gas velocity, gas holdup and bubble size, and sampling of the mineral slurry. The measured data indicate that bubble size and gas holdup decreases as the concentration of solids increases. IntroductionThe process of mineral concentration by flotation is based on contact between particles and air bubbles, the selective adhesion of hydrophobic particles onto the bubbles, and the rising of the bubble-particle aggregates to the surface of the flotation cell to overflow over the lip to form the concentrate. It is now accepted that the physical and chemical process variables that control the flotation of hydrophobic particles are closely related to gas dispersion (Schwarz and Alexander, 2005). Gas dispersion is defined by the superficial gas velocity, Jg (Torrealba-Vargas, Gomez and Finch, 2006), the gas holdup, eg (Tavera, Gomez and Finch, 1997), the bubble size, d32 (Dobby and Finch, 1986; Gorain et al., 1995; Hernandez-Aguilar et al., 2004) , and the bubble surface area flux, Sb (Manqiu and Finch, 1989; Manqiu, Finch and Uribe-Salas, 1991). In recent years, the advances that have been made in sensor technology have enabled the characterization of gas dispersion in industrial flotation cells with excellent results (Gomez and Finch, 2007). This technology advancement has allowed the gaining of a deeper understanding of such complex mechanisms as carrying capacity (Yianatos and Contreras, 2010), collection efficiency (Gorain, Franzidis and Manlapig, 1997; Massinaei et al., 2009) and bubble coalescence (Finch, Nesset and Acuña, 2008; Zangooi, Gomez and Finch, 2010)."

Jan 1, 2017

By Thomas S. Nye

Mineral exploration in the United States relies heavily on theoretical geologic concepts and indirect methods such as geophysics and geochemical prospecting, as there are few exposed areas of mineralization which have not already been explored at least once. In Mexico ore-grade samples can be cut at the surface on vein, replacement, and disseminated types of deposits in many areas. Here the problem is not in finding a mineralized area but in deciding which mineralized area can be explored and developed at the least risk and cost, and have the greatest profit potential, within the framework of Mexican mineral economics and government policies. Mexico&apos;s min¬eral industry is regulated through a system of permits for various phases of mineral exploitation, and by taxes. This regulation and its effects are not unlike those which may be expected in the United States if present legislative and administrative trends continue.

Jan 1, 1972

By Jr. Garnar

Heavy mineral mining has been a relatively small but important Florida industry for over sixty years. Geology of the Florida heavy mineral deposits is similar. Each formed along active coastlines after which the titanium minerals were upgraded in TiO2 by post depositional oxidation and leaching of the iron. There are four heavy mineral plants currently Operating in Florida. Ore is mined by dredges and the heavy minerals concentrated by gravity separation. The heavy mineral concentrates are further processed with high tension and electromagnetic separators to Produce titanium mineral concentrates for TiO2 pigment manufacturing plants. Zircon sand is produced as a co-product at all of the Florida plants. Staurolite is produced by Du Pont and Titanium Enterprises. Du Pont also markets a kyanite-sillimanite product. (Monazite is produced by Humphreys and Titanium Enterprises). Reclamation of mined-out land is an important part of heavy mineral mining. At the Du Pont plants soil is removed ahead of the dredge and placed over the quartz sand tailings. Grass is planted after fertilizing. A year later the land is fertilized again and pine trees planted. Most of the heavy mineral deposits now being mined will be nearly exhausted by the end of the century. New deposits to be mined in the 21st century will probably be smaller and lower grade than those now being mined. Advances in mineral processing technology will have to be made to allow these lower grade deposits to be mined economically.

Jan 1, 1978

By William J. Miles

The major health hazard from exposure to crystalline silica historically has been silicosis. Silicosis is the scarring of the lung from excessive exposure to crystalline silica. It has been recognized as an occupational disease for over two thousand years, since early Greek physicians noted the respiratory problems of miners, stonecutters, and quarrymen who were exposed to excessive quantities of mineral dust. During the industrial revolution, the incidence of the disease was greatly increased by the use of machinery which increased dust levels. Subsequently, the need for dust control was recognized and dust control measures were instituted. Silicosis is characterized by progressive breathlessness on exertion and develops over the course of years. X-ray images of the lungs show progressive scarring of the lungs. The symptoms are related to the amount of exposure to crystalline silica and the years of exposure.

Jan 1, 1990