Search Documents

By Boris M. Vorobjev

The paper in question discusses a wide range of topics on the coal mining environment in general and on computerized coal mine environment systems in particular. The emphasis is being made on methodological aspects of coal mine environment with reference to computerized monitoring systems Classification of computerized coal mine environment monitoring system is suggested by the author with specific reference to coal mining operations. Coal quality control system at all levels (coal face to regional levels) is also discussed briefly hereunder, since coal quality is one of the major factor for environmental management. An integrated coal mining economic and environmental management super-system is presented in this paper Review Of the UN/DTCD, UNDP European Regional project "Computerized Coal Mining Systems" is presented here. Conceptualization of a new European Regional project on Coal Mining Environment and Economic Management is also a topic discussed in the paper.

Jan 1, 1992

By Eduard Hamm

The main reasons for the development of higher heat levels in German coal mines are the increasing depth of working with the con- sequent higher rock temperatures, increased use of electrical equipment, and increasing coal output due to concentration and mechanisation of workings. In place of the normal decentralised underground cooling plants, schemes and pilot plants have been developed to produce the required cooling capacities in central air cooling units, which then supply the cold air to the underground working points where needed.

Jan 1, 1980

By Milton E. Wadsworth, Ximeng Zhu

Impurity metals can markedly influence the anodic dissolution of gold in the presence of cyanide. Several important findings related to the influence of lead are reviewed and some new observations presented. Based on the effect of pH, the scan direction, and voltage, it may be shown there are three separate voltage regimes where lead influences the anodic dissolution of gold. These are related to Pb°/ HPbO2, Au-Pb /HPbO2, and HPbO2/PbC2; oxidation-reduction reactions which provide low resistance paths for electron exchange. The gold dissolution rate was determined by direct solution analysis and is compared to the rate implied by electrochemical measurements.

Jan 1, 2005

By Charles D. Litton

This report describes a smoke particle detector which utilizes a novel three electrode configuration and 5.0 [] source of Americium 241. The detector operates on the principle of diffusional charging by a region of unipolar molecular ions. The detector is sensitive to particle concentrations in the range of 10 to 5 20 ug/m3. The detector is intended for use primarily as an early warning fire detector but has the potential for other applications of particulate monitoring. In particular, this report adresses the potential use of the detector for monitoring diesel particulate matter (DPM). To assess the viability of this application, particle size data obtained from in-mine sampling of both DPM and dust were used to derive detector sensitivity functions for DPM and dust as a function of their mass concentrations only. These sensitivity functions are dependent upon the average diameters and size distributions of the DPM and dust. Using the derived sensitivity function for DPM, experiments were conducted in a ventilated tunnel where the true DPM mass concentrations, measured using a Tapered Element Oscillating Microbalance (TEOM) were compared to the mass concentrations calculated using the detector sensitivity function. The agreement between the two measurements was good, indicating that with additional experiments, coupled with in-mine evaluation of the detector, refinement of the device for use as a continuous monitor for DPM appears feasible.

Jan 1, 1989

By V. E. Ross

A model has been developed that describes the behavior of mineral particles and water in the cleaning zone of flotation columns. The possible detachment of particles from their sites of attachment at the bubble surfaces is related to the flux of bubble surface area with increasing distance from the interface between the collection and cleaning zones and the late at which floated particles are transported into the cleaning zone. The drainage velocities of floated and entrained particles are calculated from the drainage velocity of water and the properties of the particles. The effects of wash water and inhibited drainage in the froth are also explicitly accounted for.

Jan 1, 1988

By Swati Mohanty, G. V. Rao

Sedimentary dolomitic phosphate ores are difficult to treat by flotation, and high-grade phosphate concentrates with high recoveries are difficult to obtain. The literature indicates that the reagents required for beneficiation of such ores are generally dictated by the nature of the gangue. In this paper, the optimum flotation parameters necessary for enhancing the grade and recovery of a typical low-grade dolomitic rock phosphate ore from Jhamarkotra, Rajasthan, are highlighted. The standard design-of-experiment (DOE) technique was used to obtain empirical models for both grade and recovery. The model equations were then used for optimizing the flotation parameters, including pH, percent solids, collector dosage and depressant dosage. Laboratory experiments demonstrated that a phosphate concentrate containing about 36% P205, with a recovery greater than 95%, can be obtained in a single-stage by the reverse flotation of carbonaceous minerals at the optimized conditions. Key words: Phosphate, Flotation, Dolomite

Jan 1, 2003

By Pramod C. Thakur

Sixty countries around the world mine about 5000 million tonnes of coal annually and simultaneously produce nearly 25 million tonnes (36.8 Gm3) [One tonne of methane at a temperature of 15°C and a pressure of 760 mm of mercury has a volume of 1471 cubic meters.] of methane. Many of these coal mines are very gassy and require methane drainage prior to mining as well as during mining. In spite of significant differences in the geology and reservoir properties of the coal seams, several methane drainage techniques have found universal application. The paper describes various techniques currently in use and their efficiency in recovering methane from mines. It appears that the application of state-of-the-art techniques, developed mostly in the U.S.A., can considerably increase the efficiency of methane recovery and improve the safety of mines throughout the world.

Jan 1, 1997

By J. A. Brierley, C. L. Brierley

The history, current applications and future of biotechnical developments in the metals' extraction industry are reviewed. Bioleaching of copper minerals continues to be the most significant application. Uranium bioleaching was successfully demonstrated at industrial scale. Developments are now being made in biooxidative pretreatment of refractory gold concentrates, ores and low-grade materials. Advancements are forthcoming in water and solid mine waste bioreclamation, including metals' biosorption, wetland treatment of acid mine drainage, and biodegradation of cyanide in spent, heap-leach operations. Better understanding of the types and functions of microorganisms involved in metal interactions could advance genetic engineering applications in bioleaching and bioreclamation.

Jan 1, 1993

By Kevin D. Lofftus

This paper presents a dynamic model for column flotation. The model equations are normalized and the dimensionless groups that are directly responsible in determining the column flotation behavior are identified. The resulting model equations are incorporated for computer simulation. Numerical results from computer simulations are analyzed to gather information about design and operation of column flotation devices.

Jan 1, 1988

By Yannis Faitakis, Brenda M. Wright, Gail Powley, Mark Hamblin, Randy B. Paine

A major problem in the ore extraction process is the high degree of variation in the mix of materials that make up the mined ore. The mix of materials makes it extremely difficult to characterize and predict the behavior of the ore when it is processed. The Quality Production Database (QPD) tool was successfully used in order to predict and transfer information regarding the quality characteristics of the ore being delivered to the extraction and hydrotransport unit operators. This paper describes the use of QPD in the prediction of various ore characteristics at the Syncrude Canada Ltd. processing facility.

Jan 1, 2000

By Qing Wang

A longterm overburden removal plan can be realistic and optimum only when the cost and capacity profiles off the equipment assigned to the operation are taken into consideration. Therefore, the planning should involve the proper assignment of equipment capacity by insuring a timely investment and a timely replacement policy throughout the mine life. A dynamic solution algorithm has been developed, by which all possible truck fleet alternatives are evaluated for each year off the operation. Cumulative cost off the operation is carried throughout the analysis. The optimum solution is obtained by selecting the minimum cumulative cost at the last year and tracing backward the best fleet alternative for each year. The solution provides: 1. the optimum amount of overburden to be removed each year; 2. the best fleet to be assigned to the job; and 3. the best equipment replacement policy.

Jan 1, 1989

By R. E. Johnson, W. Kat, B. R. Palmer, van Sandwijk A., G. Van Weert, S. Honingh

In-plant recycling of dust from iron making BF's creates undesirable circulating loads of volatile trace elements such as zinc and lead. Disposal of such dusts creates environmental problems, hence a separate treatment is indicated. Since the bulk of the zinc and lead compounds occurs in the fine dust fraction; hydrocycloning the slurry from the BF gas cleaning operation results in upgrading the material for treatment. A process has been proposed, whereby the zinc and lead are solubilized from the fine fraction with spent hydrochloric acid from steel pickling. The stoichiometry of this autoclave oxidation process is adjusted to simultaneously precipitate, by oxyhydrolysis, most of the iron for recycling to the BF's. Lead and zinc are successively recovered from the filtrate as low chloride precipitates. This paper describes additional testwork, leading to the design of a pilot plant which was planned to begin operation in 1992.

Jan 1, 1993

By I. G. Ediz, D. W. Dixon, W. M. Fidler

In this paper a new method for the arresting of tunnel explosions is presented. In the proposed technique, the on coming explosion is detected by a pressure sensitive device by a pre-determined rise in static pressure. The sensor then triggers a mechanism which causes the explosion door to be closed in a specially constructed concrete barrier zone. The doors are of a special construction and consist of perforated steel plates that allow part of the blast wave to be transmitted but do not allow the passage of the flame. A number of design parameters have been identified, including: the likely amplitudes of the transmitted/reflected pressure waves that would govern the explosion door pressure loading; thickness of the perforated steel packages; perforation dimensions; heat transfer across the door and other factors.

Jan 1, 1995

By K. A. Natarajan, M. K. Yelloji Rao

The electrochemistry of sphalerite and chalcopyrite was investigated under both open-circuit and applied potential conditions. Emphasis was placed on the selective dissolution of sphalerite from a mixture of sphalerite-chalcopyrite flotation concentrates as a function of applied potential, acid concentration, pulp density, and time. Morphological studies using a scanning electron microscope (SEM) were also carried out with chemically leached, galvanically leached, and unleached surfaces of sphalerite and chalcopyrite. Selective dissoulution of sphalerite could be achieved if the mixed chalcopyrite-sphalerite concentrate slurry was maintained at a negative applied potential of -0.4V (SCE). Probable mechanisms involved in the selective dissolution of zinc are disscussed.

Jan 1, 1990

By Gary Buchan

During several months in 1996 and 1997, Cyprus Twentymile Coal Co. (TCC) set world production records at its Twentymile Mine in northwestern Colorado. These records were due to the company's implementation of a state-of-the-art longwall mining and conveyance system along with a -highly dedicated work force. This article is a case study of the design of long panels at the mine from conception to implementation. Obstacles that needed to be overcome included subsidence engineering, environmental regulations, conveyance, ventilation, equipment design and continuous miner (CM) development timing.

Jan 1, 1998

By R. Kanniganti, M. Karmis, C. Haycocks

An extensive review of multi-seam under-mining literature was conducted and a data base of case studies was assembled . A critical review of the design principles outlined in this literature resulted in the compilation of specific design criteria for the design of lower seam mines. Analysis of this criteria demonstrated the necessity for a protocol for the design of unsymmetrically loaded pillars. Such a design criteria was developed using finite element methods for a wide range of possible loading conditions. This design criteria can be utilized for underlying pillar design when the loading conditions can be determined. To facilitate using all the under-mining research results by field/planning engineers a Windows TM based software package was developed. This software package contains a multi-seam tutorial, analytical tools and a case history database. The package is user friendly and fully interactive and supported with extensive on-line help. The package contains numerous case studies of multi-seam mines that can be reviewed to facilitate analyses.

Jan 1, 1996

By F. M. Doyle, Robert G. Robins, E. Peters

Stability diagrams for the Cu-S-H2O system have been widely applied over many years. Stability diagrams for aqueous systems generally, have been generated by computer, but with the programs for Potential-pH diagrams in particular, a common routine leads to error in multi-element systems. In this paper these errors, and some misinterpretation of diagrams are considered. In most of the published diagrams for the Cu-S-H2O system there has been no account of the sulfide complexes of copper. Here, the free energies of formation for the various species in the system have been re-evaluated for consistency, and some diagrams for the Cu-S-H2O system ( generated with the program DIASTAB Vers.5 ) are presented.

Jan 1, 1993

By I. S. Parrish, D. W. Kappes, G. G. Austin

Micron-sized gold disseminated in lower Cambrian siltstone has been found at the Sterling mine near Beatty, NV. A shoestring-shaped body has been developed by central and fringe drifts and is being mined via a modified retreat room and pillar system. The siliceous ore crushed to 5.08 cm (2 in ) is stacked to 4.6 m (15 ft) over a layered sand, gravel, and impervious PVC base. Gold is leached using a 0.1% cyanide solution and deposited on activated coconut shell carbon. Stripping of the carbon by hot solutions of 1% NaOH and 20% Ethanol yields overall recovery of about 75% of the fire assay head.

Jan 1, 1983

By R. A. * Russell, J. R. * Brooks, E. J. Griffith

In 1967, a major impoundment to contain phosphate tailings was built near Columbia, TN. Precise records were maintained on the behavior of the impoundment throughout its 20-year active life. The volume of the impoundment was determined. The DNT (dry net tons) of solids added to the impoundment were continuously measured. The rise of the mud line in the impoundment was measured monthly. The density of the settled strata was determined, as required to understand the behavior of the settled tailings. And experiments were per formed to increase the settled density of the clays. The impoundment is currently being retired and stabilized. It covers more than 400 acres and the settled muds are almost 200 ft thick. The clays have been sufficiently solidified with electroendosmosis to support the growth of cypress trees. More than three milllion trees are being planted.

Jan 1, 1992

By T. N. Patra, Sanjeeva Latchireddi, B. K. Mishra, Sravan K. Prathy

The motion of grinding balls has been the subject of study since 191 9 when Davis published the first treatise on this subject. Subsequently came the notion that knowing mill power draft, using Bond equation or others, is sufficient to do an analysis of grinding. Next, population balance models provided accurate scale-up from small laboratory size mills to very large plant size mills. However, this success was not repeated when dealing with semiautogenous grinding mill. The study of charge motion with the discrete element method provides support and answers to such issues. Besides providing an accurate picture of charge motion in large mills, the method begs the investigator to study grate and pulp lifter equally critically with fluid dynamic principles. Hence, in recent years, the field of comminution in grinding mills is advancing on a firm footing.

Jan 1, 2005