Search Documents

By T. Sakaguehi

Some attempts were made to recover and remove of uranium that may be present in refining effluents, mine waste Water, and other waste sources by using microbial biomass. To establish which microorganisms accumulate the most uranium, 135 species of microorganisms (42 bacteria, 26 yeasts, 34 fungi and 33 actinomycetes) were screened. Of these 135 species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stuzeri, Neurospora sitophila, Streptomyces albus and Streptomvces viridochromogenes. In addition to the research on uranium uptake, thorium recovery by using microorganisms was investigated. High abilities were found in Streptomyces levoris and Bacillus subtilis. The selective accumulation of heavy metal ions by various microorganisms has also been examined. Uranyl, mercury and lead ions were readily accumulated by almost all of the species of microorganisms tested. Actinomycetes and fungi differ from many bacteria and most yeasts in their selective accumulation of uranium, and mercury. The basic features of uranium uptake by Streptomyces viridochromogenes, a microorganisms with high uranium-uptake ability, were investigated systematically. Synthesizing these results, we suggested that the accumulation of uranium into these microbial cells is not directly mediated by any metabolic process:, but almost completely dependent upon physicochemical adsorption on the cell components. In addition to this fundamental research, uranium recovery was investigated in immobilized Streptomyces viridochromogenes. These immobilized cells adsorbed, uranium readily and selectively. The immobilized cells recovered uranium almost quantitatively and almost all uranium adsorbed was desorbed with 0.1 N Na2CO3, These results showed that microbial cells are more stable after Immobilization and can be used repeatedly for the process of uranium adsorption-desorption. These results suggested that these microbial cells can be used for the recovery and removal of nuclear fuel elements, such as uranium and thorium, from refining effluents and mine waste water.

Jan 1, 1991

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

"This study investigated calcination behavior of one of the Turkish laterite deposits, which was recently found in Sivrihisar region. Representative limonitic laterite samples (1.26% Ni) taken from Yunusemre Karasivritepe and Kucuksivritepe location were first subjected to drying. Removal of chemically bound water and other volatiles were then studied, in detail. In the calcination experiments, temperature and time were the main experimental variables. Thermal treatment was conducted at the specific temperatures in 250 °C - 800 °C range. The weight losses due to elimination of chemically bound water and other volatiles were reported to be approximately 10 per cent of the weight of the ore. For the particle size used in the current work, 700 °C and 40 minutes were determined to be the optimum calcination temperature and time, respectively.IntroductionThe nickel ores that are economically valuable can be grouped into two categories: sulphide type nickel ores and oxide type nickel ores, namely laterites. Over all reserves in the world, 40% are sulphide nickel ores and the remaining 60% are laterites [1]. Pyrometallurgical nickel extraction from sulphide type nickel ores is conducted via matte smelting. More recently, laterite ore bodies have been subjected to nickel extraction. Depending mainly on the chemical composition of the laterite and the process economics, various extraction techniques have been implemented: pyrometallurgical route involves ferronickel smelting. High pressure acid leaching (HPAL) is the commercial method for hydrometallurgical nickel extraction, while ammonia leaching (CARON Process) is a combination of pyrometallurgical and hydrometallurgical processes [2]. With the improvements in these processes, it is predicted that laterite’s share in the world nickel production will rise to 50% in 2012, while it was reported to be 42% in 1,200,000 tons of annual production in 2003 [3]."

Jan 1, 2011

By Walter Curlook

An atmospheric acid leaching process for leaching nickel and cobalt from highly-serpentinized saprolitic fractions of nickel laterite deposits has been developed and patented [I]. The process involves leaching the highly-serpentinized saprolitic portion of the nickel laterite ore profile in strong sulphuric acid solutions at atmospheric pressure and temperatures between 80°C and 100°C, essentially autogenously, to extract over 85% of its contained nickel content and a large proportion of its cobalt content after leaching times of about one hour. The amount of sulphuric acid used in the leaching process is between 80% and 100% by weight of the finely ground highly-serpentinized saprolite ore on a dry weight basis. The metal values are recovered as intermediate products. Key words: Atmospheric Leaching; Nickel Oxide Ores; Laterites

Jan 1, 2004

By Toshiki Kabutomori

In fuel cell powered automobiles, hydrogen is required to be stored in materials that have a hydrogen storage density of over 4 mass%; further, these materials should be capable of supplying hydrogen by using the waste heat from a fuel cell, which is at a temperature of 373 K, in order to match the mileage of gasoline-powered vehicles. A Ti-Cr-V alloy, which exhibits a BCC structure and forms a solid solution, is a promising candidate for onboard hydrogen storage materials. Although it has a large hydrogen storage capacity of over 3.9 mass%, the rechargeable hydrogen capacity is limited to approximately 2.6 mass%. In this study, the effects of fine pulverization of the alloy on PCT (hydrogen pressure-composition-isotherm) characteristics were investigated in order to improve the rechargeable hydrogen storage capacity of the alloy. From the PCT measurements of the finely pulverized samples of the alloy, a plateau in the absorption curve was observed to begin at a hydrogen concentration of 0.5 mass%; further, a rechargeable hydrogen storage capacity of 3.3 mass% was obtained. This was greater than that obtained from the sample that was not finely pulverized, i.e., 2.5 mass%. However, the plateau width in the desorption curve was 2.5 mass%, which was the same as that observed for the sample that was not finely pulverized. The increase in the rechargeable hydrogen capacity during absorption is attributed to the precipitation of the -hydride phase (MH~2) directly from the metal phase (phase). The precipitation of the phase (MH~0.5), which should be formed in low hydrogen concentrations, is suppressed as a result of a possible reduction in the internal defects such as dislocations, vacancies, and grain boundaries by fine pulverization and annealing of the alloy.

Jan 1, 2006

By Vasil Kopaleishvili

The bainitic Fe-C-Si alloys with optimum content of retained austenite serve as ?containers? for storing of hydrogen. Both the vacancies of fcc lattice and the possibility of forming hydrides of silicon and other alloying elements will be used. The idea is based on our scientific hypothesis. There is the silicon threshold (Si=0,50%) in "Fe-Si" system and Fe-C bainitic alloys, above which it causes self-organized phenomena: sudden increase of hydrogen solubility and amount of retained austenite in the alloy after ??ß transformation, formation of two supersaturated solid solutions <a??r>, "rejuvenation? and its reverse process. Rapprochement of iron atoms when Si=0,50%, causes appearance of new covalent forces where uncompensated electrons of 3d-subshell are involved and it provokes synergetic phenomena. They ?free? silicon atoms from the previous bonds. After that silicon itself becomes a getter of hydrogen using vacancies (14) of 3P2(6)d0(10) subshell and it results in sudden increase of hydrogen solubility in metal. Simultaneously sudden decrease of iron activity takes place. That in its turn ?releases? the carbon. Thus, its redistribution, controlling the bainitic transformation, is hastened. It stipulates for creation of ?brittle bainite" B[a(C,H)+?r(C,H)] after ??ß transformation. While weathering of metal, "rejuvenating", hydrogen diffuses in ?islets? of retained austenite and ?relaxed bainite? (B[(C)+?r(C,H+H)]) is obtained. When heating austenite ?(C,H) is obtained, and after cooling ?brittle bainite? is obtained, etc. Presented scientific hypothesis explains the available experimental facts ("rejuvenation? and its reverse process, graphitization, weldability, forming of flakes, reaching high strength, etc.) in a new manner, as well as, gives real opportunity for creating of new trends in many fields, e.g. iron based HAA. Provisional data having been obtained are encouraging.

Jan 1, 2006

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008

By Jun Lu, Min Chen, Wei-jian Su, Jian-zhong Luo, Yu-tao Lei

"In the case of treating phosphatizing wastewater containing zinc, zinc had an impact on the solution chemistry, especially on pH. Fe2(SO4)3 and CaCl2 were used as precipitators to remove phosphate from zincic phosphatizing wastewater and the optimum pH was investigated. Zinc ion had a significant effect on the optimum pH. The optimum pH ranges were 12.10(inlet concentration of 15.67mg/L, outlet concentration of 9.53mg/L), 3.04-5.50(inlet concentration of 11.97mg/L, outlet concentration of 0.44-0.26mg/L), and more than 10.72(inlet concentration of 12.24mg/L, outlet concentration of less than 0.47mg/L) under the conditions without precipitator, with Fe2(SO4)3 and with CaCl2 respectively.Introduction Phosphate coating is commonly used for protective coating of machine elements. Including oil removal by caustic washing, rust removal by acid washing, phosphatization and inactivation, the phosphatization process produces wastewater containing inorganic salt of high concentration, especially the phosphate, beyond the environmental standards and polluting environment seriously. What’s more, the wastewater from zincic phosphatizing technology also contains another pollutant, zinc. At present, Chemical Precipitation (CP) and Biological Nutrient Removal (BNR) are two of most common technologies of phosphate removal. BNR, such as A/O, A2/O and UCT technology, is suited for wastewater containing organ phosphorus of low concentration and CP for wastewater with phosphate of high concentration [1]. Researches on CP treating wastewater containing phosphate of high concentration, mainly focus on adding quantity of precipitators[2-5] and coagulants[2-4] and the choice of technologies[3-9]."

Jan 1, 2008

By Denise Nascimento, Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Renan Carreiro, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"Natural fibers obtained from plants have increasingly been used as reinforcement of polymeric composites in engineering applications. This is the case of the fiber extracted from the piassava palm tree, a native of the southeast region of South America, which for a long time has been used in simple items like brooms and brushes. Recently it was reported that the tensile strength of the piassava fiber varied inversely with the equivalent diameter. Following that previous work, the elastic modulus and the density dependence on the diameter of stiffer piassava fibers of the Attalea fiinifera species was investigated. Precise measurements with a profile projector and Weibull analysis of the experimental results indicated that both the elastic modulus and the density of piassava fibers also follow an inverse correlation with the diameter. Scanning electron microscopy observations of the microstructure and fracture surface showed that defects and participation of microfibrils are responsible for this correlation.IntroductionIn the past decades, both the increase in the price of the petroleum and climate changes due to greenhouse gas emissions are motivating the use of renewable and low cost natural materials as a substitute for energy intensive and CO2 contributor synthetic materials [1]. A typical case is that of natural cellulose-based fibers extracted from cultivated plants in comparison to glass fibers, which are extensively used for composite reinforcement. In fact, these natural lignocellulosic fibers are increasingly being investigated [2-6] as possible reinforcements of polymeric composites, and in some cases, successfully replacing glass fiber composites in engineering applications [7]. The automobile industry has remarkable examples of lignocellulosic fiber composite substitutions [8-10]. Not only do some of these fibers display specific mechanical properties comparable to glass fibers but their composites also contribute to lower equipment wear and better finishing of molded components [6]."

Jan 1, 2012

By Gaifeng Xue, Lijun Lu, Honghui Fang, Jiannyang Hwang

"Steel slag has been stockpiled in many steel mills due to its poor performance in various construction related applications. Free lime in steel slag has been considered as a major barrier for its utilizations. Composite of steel slag and powders of granulated blast furnace slag have been found an excellent cementitious material for concrete. Portland cement is not required in this kind of concrete. Concretes with various amounts of steel slag and powders of granulated blast furnace slag additions have been investigated. Physical and chemical properties of the products were examined. High performance concrete can be obtained. Field testing of the concrete products was conducted for various applications, including buildings and pavements, and the results demonstrated the soundness of the concrete. Drill cores of field tested concrete, with ages up to 26 years, were examined for the microstructures under SEM.IntroductionIn the steel industry, a major source of the solid waste is steel slag. Steel slag has poor stability in construction applications. This is a major reason that only a small amount of steel slag has been utilized. Some of the reported applications include the land filling/creation in the sea, road base materials, soil treatment for acid neutralization and micronutrients supply, and sintering aid in the sintering plant of the steel industry [1].To solve the stability problem for using steel slag as construction materials, the common approach is to find a method capable of depressing or eliminating the expansion of steel slag. Free lime in steel slag is the major component that causes the expansion. Aging and hydration pretreatment of free lime in steel slag are the well known methods for increasing the steel slag stability. However, there has been limited success on these approaches due to that a large portion of free lime is locked in the grains during the pretreatment process."

Jan 1, 2012

By Renato G. Bautista

The chemistry of the separation of metals from each other and from the other undesirable components involve multiple simultaneous chemical reactions. In the case of leaching, the heterogeneous chemical reactions between the solid and the liquid phase may be limited to a few reactions. In the homogeneous liquid phase, the number of simultaneous chemical reactions could be double or triple that of the number of heterogeneous reactions:. The rate of dissolution becomes very dependent on the changing concentrations of the significant chemical species taking part in the multiple reactions in both the heterogenous and homogeneous phase. The rate expression developed for the process must take into account the mechanism of chemical reactions in order to best represent the actual process. This paper also examine the role of mass transfer with chemical reaction in the develpoment of the rate equations for dissolution, liquid-liquid extraction, membrane separation, precipitation, and electrodeposition.

Jan 1, 1996

By Scott A. Howard

MgO is routinely used as the basis for refractory materials, however, its susceptibility to hydration may result in dimensional instability and subsequent failure. The addition of boron has been shown to reduce th,e hydration susceptibility of MgO yet its dissolution into certain grades of steel may degrade their performance. In order to predict the efficacy of reducing hydration susceptibility by the incorporation of mono-, di-and tri-and quadravalent cations, the lattices of various cation-substituted systems were modeled. To more accurately simulate the substituted lattices, either cation or anion vacancies were incorporated to maintain electrical neutrality and all possible arrangements of defects in a 2x2x2 MgO supercell were investigated. Correlations were then made between the lattice energies of these systems and their susceptibility to hydration as reported in the literature. The results indicate the presence of higher charged cations tended to increase lattice stability while the cations with lower valency tended to have lower lattice energies. The relatively small body of experimental results available in the literature are consistent&apos; with this study&apos;s results.

Jan 1, 1989

By D. J. Senor

Closed chamber incineration (CCI) is a novel technique by which irradiated nuclear graphite may be destroyed without the risk of radioactive cation release into the environment. The process utilizes an enclosed combustion chamber coupled with molten carbonate fuel cells (MCFCs). The transport of cations is intrinsically suppressed by the MCFCs, such that only the combustion gases are conducted through for release to the environment. An example CCI design was developed which had as its goal the destruction of graphite fuel elements from the Fort St. Vrain reactor (FSVR). By employing CCI, the volume of high level waste from the FSVR will be reduced by approximately 87 percent. Additionally, the incineration process will convert the Sic coating on the FSVR fuel particles to SiO2, thus creating a form potentially suitable for direct incorporation in a vitrification process stream. The design is compact, efficient, and makes use of currently available technology.

Jan 1, 1994

By Yuanyuan Wang, Yuhao Ding, Hao Bai, Kang Zhou, Guangwei Du

"In this paper, the list analysis of GHG emissions of aluminum industry was conducted based on the data from typical electrolytic aluminum plants of a China’s northwest province. The results show that under the conditions of average anode effect coefficient as 0.16 times/(cell• day) and anode duration as 5 minutes per day, equivalent emissions of CO2 reached 1.23 ton per ton of aluminum, in which PFC emissions accounted for about 71%. Compared with foreign advanced level, which is 0.87 ton per ton of aluminum under the conditions of average anode effect coefficient as 0.01 times/(cell•day) and anode duration as 0.46 minutes per day, there is much room for China’s aluminum industry to reduce GHG emissions. Since anode effect plays an important role on PFCs generation in electrolytic aluminum process, how to control anode effect strictly becomes the key factor for remarkable reduction of GHG emissions in China’s aluminum industry.IntroductionTechnology of aluminum electrolysis is a mature and efficient process of aluminum production. Due to the huge demand on aluminum worldwide, so resource consumption, energy consumption and pollutant emissions in the process of aluminum production are still large. The global output of aluminum reached 45193 kt in 2012. A large amount of CO2 and PFCs are produced in the process of aluminum production, and the greenhouse effect and environmental pollution caused by emissions of them is a concern. PFCs belong to a powerful greenhouse gas, thus emission reduction of PFCs is very important for aluminum electrolysis industry. At present, China's aluminum production accounts for about 33% of the world's aluminum production, and controlling PFCs emission has become the key point of pollution control of aluminum electrolysis industry in China [1].Taking the case of a typical electrolytic aluminum plant of a China’s northwest province, this paper studies the list analysis of GHG emissions of aluminum industry in China. GHG emissions of a China’s northwest province were calculated through investigating existing situation of aluminum electrolysis industry in the province, knowing capacity, output, main production technology and equipment level of aluminum electrolysis industry, and using the calculation framework and methods of GHG emissions of aluminum electrolysis industry, which were put forward by the intergovernmental panel on climate change (IPCC), the international aluminum association and other organizations at home and abroad. The list analysis of GHG emissions of aluminum electrolysis industry will offer useful information in promoting emission reduction of GHG in aluminum electrolysis industry, improve the efficiency of energy utilization."

Jan 1, 2014

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts. The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10.1 atm. The concentration ofCu2+ in such slags becomes significant at oxygen potentials of greater than 10&apos;1 atm at 1300 ?C. The activities of CuOo.s and AsOl.S in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of Si02 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2xlO?3 cm2/s at 1350 °C and activation energy of 16 kcal/mol Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300 °c. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material.

Jan 1, 2003

By Jussi Vaamol

A commercial CFD-code was used to solve isothermal flow fields of gas and liquid in a Peirce-Smith converter. The model was validated with a 1/4 scale water model, and parametric study. Limits of the modeling technique used were recognized, but calculated results indicate that the present model predicts the general flow field with reasonable accuracy. The model was used to examine general flow conditions in an industrial scale PS-converter. Typical scaling factors of physical models were also evaluated with the aid of predicted bubble distribution, patterns of the flow fields and magnitude of flow velocities. The numerical simulations were found to open new viewpoints to the fluid dynamic related phenomena in the PS-process.

Jan 1, 1998

By Ljiljana Solujic

The need for the removal of mercury from the precious metals extraction circuits may be influenced by process, environmental, as well as by occupational hazard reasons. In these circuits mercury is mainly present as cyanide complexes. The effectiveness of any stabilization method will be influenced by the high thermodynamic stability mercury-cyano species exhibit in an aqueous solution. In this study, we have investigated the utility of the trisodium salt of trimmercapto-s-triazine (TMT) for precipitation of mercury from the corresponding cyano-complexes. The influence of pH molar ratio of TMT to Hg, coagulant and flocculant additions, excess of free cyanide, as well as the presence of other metal-cyano species on the effectiveness of mercury precipitation were investigated in detail. Also, a "teal world" precious metals mill effluent initially containing ~7 ug/mL (ppm) of Hg was treated and A was found that greater than 99.8% of the mercury was removed from the solution as am insoluble Hg/TMT complex.

Jan 1, 1996

By John M. Gaines

Lead concentrates from the Viburnum Trend in the Southeast Missouri Lead district are sintered prior to smelting to bind the particles together homogenize the feed, and reduce the sulfur content. Good sinter forms competent masses about 4 to 6 inches across, that hal!e about 15% porosity and good mechanical strength to withstand transport and the weight of the overlying load in the smelter. Bad sinter has poor mechanical strength and forms fine fragments that retard the circulation of reducing gases in the furnace and lengthen the time required for reduction. The productivity of the lead smelter depends on good sinter feed. Because some lead sinter plants produce bad sinter about 20% of the time, this applied mineralogy study has been undertaken to determine the mineralogical and microtextural differences between good and bad sinter. A reflected light microscopic study of 130 polished sections has shown that good and bad sinters differ distinctly in their mineralogy, tex1ure. and character of, porosity. Good sinter consists of hardystonite, franklinite. lead-zinc-bearing magnesium-calcium silicate, lead silicate matrix, and large crystals of calcium-magnesium-iron silicate, together with minor amounts of lead oxides, lead-zinc silicate, metallic lead, specular hematite, magnetite, lead-iron-bearing zincite and zinc-Iead-magnesium-bearing wustite in a tightly intergrown mesh of crystals and with an evenly distributed porosity of 15% to 20%. Electron microprobe analyses show that the principal phases contain lead (or zinc): hardystonite (4-20% Pb) franklinite (2-14% Pb) and lead silicate matrix (65-74% Pb). Bad sinter differs from good sinter in the greater abundance of lead silicate matrix, galena metallic lead, and lead oxides and the lesser abundance of hardystonite, franklinite and calcium-magnesium-iron silicate. Bad Sinter is characterized by a lack of an intimate intergrowth of the constituent phases. Its porosity is much lower commonly 0 to 5% and those pores are concentrated in local areas rather than distributed evenly throughout the sinter.

Jan 1, 1991

By Yuan She, Qihang Liu, Keng Wu, Hailiang Ren

By observing different coal char’s microstructures and microscopic morphologies during the coking process, the characteristics of COREX coal char’s microstructure and properties were analyzed. MCRI and MCSR were used to respectively describe the reactivity and the strength after reaction of coal char, with those of BF’s coke for reference, and then the physical meaning of MCRI and MCSR were given. MCRI and MCSR were determined by the composition of coal char. For the two kinds of COREX coal, the formula to forecast the hot performance of coal char was set up by making a multiple linear regression between the hot performance and microstructure of the coal char at 1100℃, and the predictive values of coal char’s hot performance at 600℃, 800℃ and 1000℃ coincided well with the measured values.

Jan 1, 2015

By Chan. C. L., Zehr. R., M. M. Chen, J. Mazumder

"Two three-dimensional models of a surface tension gradient driven flow during laser surface heating are developed. The first model is based on a perturbation solution. The basic solution corresponds to the stationary axisynwnetric case and perturbation is based on a small scanning velocity. The advantage of seeking a perturbation solution, as it turns out, is that the three-dimensional flow is modeled by two sets of two-dimensional equations which are presumably much more tractable than the original three-dimensional equations. Numerical solutions are obtained and discussed. The second model is a full three-dimensional numerical solution of the Navier-Stokes equations, using a point-by-point partially vectorized iteration scheme. Surface shape is also determined in a self-consistent manner. The effect of the presence of convection on pool geometry, cooling rate and solute redistribution is presented and discussed.IntroductionThe existence of fluid flow and convection and their effects were first reported in the fifties (1,2). The role of convection in controlling pool geometry such as pool shape, undercut and ripples, and defects such as variable penetration, porosity and lack of fusion and weld properties such as weld homogeneity and bead formation is studied by a number of researchers and is reviewed by the authors in a recent paper (3).Recently, surface tension gradient driven flow has been identified as one of the forces responsible for convection within the molten pool (4,5). It is postulated that surface tension gradient driven flow is responsible for the surface ripple formation in the weld pool (6-8). Oreper, et al. (9) developed a two-dimensional convection model. Buoyancy, electromagnetic and surface tension gradient forces were considered. The formulation was based on a specified pool profile. It was found that the surface tension gradient is the dominant force in most cases. However, the solid-liquid interface is not known a priori. In fact, the solid-liquid interface, i.e. the pool shape, is a piece of information that the model should be able to predict. A two-dimensional transient self-consistent (i.e. the solid-liquid interface is solved as part of the solution] model for laser surface melted pool was first developed by Chan, Mazumder, and Chen (3)). This model predicted a non-uniform cooling rate, hence non-uniform microstructure. Depending on the Prandtl number (i.e. material) and surface tension number, the shape of the molten region as well as the cooling rate changes. It was also predicted that the recirculating velocity is of one or two order of magnitude higher than that of the scanning velocity. This model provides the detail of the flow field and heat transfer on a plane perpendicular to the scanning direction. However, the front-to-back motion and its effect on heat transfer also play important roles in the physical process, especially for the fact that the recirculating velocity is so much higher than the scanning velocity. Such a motion cannot be obtained from two-dimensional models."

Jan 1, 1986

By Lv Guozhi, Niu Liping, Liu Yan, Zhang Zhiqi, He Jicheng, Zhang Ting’an, Dou Zhihe

"CuCr alloy can be extensively used as contact materials in integrated circuit, electrodes, electric contact and high strength conductor. We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The slags and CuCr alloy were characterized respectively by XRD and SEM. The results show that when the additive is Na3AlF6, the slag consist of Al2O3 and Cr. When the additive is CaF2, the slag consist of Al2O3, Cr, CaF2 and CaAl4O7. The inclusions in CuCr alloy are mainly Al2O3 and pores which disperse in Cu-rich zone and Cu-Cr phase interface. When 5% CaF2 and 5% KClO3 are added, there are fewer pores and inclusions, and the more better microstructure.1 IntroduceCuCr alloy is the contact terminal material with an eximious properties[1,2], which gradually replaces CuBi alloy becoming the first choice for contact terminal material in the medium and high power vacuum switch after the 1970s. The traditional preparation methods of CuCr alloy mainly contain powder metallurgy, infiltration process and vacuum electric arc melting methods. But the above methods exist some shortcomings, such as poor product quality, high cost of production, processes complex ect[3-9]. CuCr alloy is made by the thermit reduction self-propagating method, which uses CuO, Cr2O3 and Al as raw material to get the high-temperature melt, and then casts to manufacture CuCr alloy ingot, which response equation follows as:"

Jan 1, 2012