Search Documents

By Vinícius Cardoso da Rocha

Frente ao cenário industrial competitivo, o emprego de fluxantes em lingotamento contínuo de aços permitiu o aumento da produtividade e a redução das perdas metálicas por defeitos superficiais. Neste estudo, avaliou-se a aplicabilidade de dois tipos de fluxantes para produção do aço SAE 1046 Mod. Os fluxantes foram testados quanto ao desgaste da válvula submersa, frenagem (atrito) na interface metal/molde e rejeição dos produtos de lingotamento devido à presença de defeitos superficiais. O fluxante teste apresentou taxa de desgaste de válvula submersa de 2,2 mm/corrida, frente ao fluxante padrão com 0,8 mm/corrida. Entretanto, o fluxante teste demonstrou bons resultados quanto à lubrificação do molde, reduzindo a frenagem (atrito) entre o metal e molde e, consequentemente, melhorando a qualidade superficial do produto de lingotamento. A rejeição dos produtos por defeitos superficiais reduziu 47% com o fluxante teste.

Aug 16, 2017

By J. Macassi M.

La plata es uno de los recursos metálicos más importantes de Centromin, cuya complejidad de sus características requiere de un proceso de caracterización, identificación y conocimiento del comportamiento de los minerales que lo contienen, frente a los procesos existentes y a las nuevas posibilidades técnicas propuestas. En ese sentido, el texto plantea una alternativa hidrometalúrgica de solución para la recuperación de plata contenida en menas de hierro del tipo óxido sulfato, considerándola como una etapa de pretratamiento con una solución básica de hidróxido de sodio, de forma que esta tecnología permite beneficiar menas de naturaleza refractaria que contienen significativas cantidades de metales preciosos a un costo más económico.

Aug 26, 1988

By M. Olper

The zinc recycling is assuming more and more importance. A lot of zinc secondaries and wastes are ready to be collected and converted to zinc metal. The impurities present in these materials and the technical and economical problems that some traditional ways of treating these materials are facing, call for new technologies. The EZINEX Process, a fully hydrometallurgical process industrially proven to convert oxidised zinc bearing materials directly to zinc cathodes, is an innovative process that can deal with any kind of zinc waste/secondaries in a very powerful way. In this paper the highlights of this process will be shown and discussed to demonstrate the robustness of the process and its economic viability.

Jan 1, 2008

By K. V. Konigsmann

"Mattagami Lake Mines Ltd operate a zinc-copper mine with an annual output of about 200,000 tons of zinc and 30,000 tons of copper concentrates. Zinc concentrates arc shipped to a company owned smelter in Valleyfield (a distance of 690 miles), for Export to Quebec City and also to Josephtown, Pennsylvania (1,060 miles, Figure 1.)The protection of concentrates in open gondola rail shipments has been a matter of concern since operations commenced. Considerable financial losses did occur at times because of wind erosion. Operating difficulties were also encountered by customers because of excessive moisture accummulation in the concentrates. Test shipments made in 1969 established the magnitude of losses in open cars. The results and subsequent investigations at our mines and elsewhere confirmed that load protection is an economic necessity.Many types of covers were experimented with, more or less successfully. In 1972 we agreed on a joint program with Dupont of Canada Limited. A new type of cover was developed by early 1973. It has been in use since, undergoing several improvements as experience accumulates."

Jan 1, 1975

By C Skublak

The Government of Canada recently passed a new regulation to control the liquid discharges from metal mines in Canada. The Metal Mining Effluent Regulation of the Federal Fisheries Act will come into force within the next six months. As a result the Ontario Regional Office of Environment Canada has developed a compliance promotion program to accompany the new regulation. How the mines implement the regulation will be key to its success. This paper will briefly outline the components of this regulation, including the reporting structure, the discharge parameters and limits, as well as the requirement for the mines to conduct long-term environmental effects monitoring on their effluent discharge. The presentation will give a brief account of the compliance promotion program, and then focus on the spill trends from Ontario mining operations. The province of Ontario has the largest concentration of metal mining operations in the country with approximately 40 active mines.

Jan 1, 2002

By Juan Francisco Mori, Miguel Ángel Aucapoma, Pablo Zevallos

En este artículo se describe el prototipo de un equipamiento instrumentado digital cuya función es monitorear la condición de los techos de los socavones para evitar que se produzcan accidentes por desprendimientos generados por el debilitamiento de las estructuras que sostienen los techos, debido al corrimiento de las estructuras del macizo rocoso. Básicamente el sistema informa mediante la activación de alarmas pre-configuradas al interior de mina, con el propósito de prevenir y evacuar al personal.

Apr 30, 2020

By R J. Johnson

The development of "SANFO" has provided the Mining Industry with a LOW COST HIGH GAS VOLUME, VARIABLE DENSITY, Blasting Agent which can be blended "On Site" in a simple Agitator mixing and charging system by mine site employees.

Jan 1, 1996

Study on New Tungsten Beneficiation Technological Flow Sheet of Shizhuyuan Polymetallic Mine

Sep 13, 2010

Background: Frictional ignitions continue to be a problem facing the U.S. underground coal mining industry. Many methane igni-tions are associated with the impact of mining machine cutter bits on quartzitic material (e.g., sandstone) during the coal-cutting process. Most ignitions result in small methane-air fireballs often only a few feet in size and limited to the cutter head location. However, under certain conditions, frictional ignitions can lead to larger methane explosions and/or fires with the potential for causing serious injury or death to the mining machine operator and other nearby miners. The requirements for a frictional ignition are a flammable volume of methane-air and an ignition source. This source is usually the hot streak caused by the frictional impact of the mining bit on hard rock, and the frequency of occurrence increases with increased bit wear. Another possible ignition source is the fric-tional impact of rock on rock during a roof fall.

Mar 1, 2008

By E J. Cowan

Efficiency demands that mine geologists devote the most time to tasks where they can have the biggest effect on production. One of the most time-consuming tasks is geological interpretation of the orebody and turning this into a block model for the planning engineers.The current best practice for mines that require a geologically constrained resource model involves capturing the interpretation of geologists as three-dimensional (3D) wireframes. However, there is significant overhead in the production of valid wireframes from sectional and plan interpretations. This overhead consists of the mundane tasks of digitising polylines, then building 3D wireframes and validating them. While software can simplify this task, the current process is not the best use of a geologist’s time. Under time pressure exerted by planning engineers and the time required for modelling from polylines, geologists are forced to roll-up the presence of other elements or impurities into the interpretation and encode them in the polylines, even though it is often desirable to consider these other factors separately.While it might seem unlikely that mine geologists can produce constrained geological models without the intermediary of wireframes, the technology to accomplish this is getting closer.In this paper, the results of a trial at the Savage River magnetite mine, which is owned and operated by Grange Resources Ltd, are reported. The trial was for a ‘direct-to-block’ implicit geological modelling method. The focus was on creating a geological attributed block model from drill hole geological log data; resource estimates were not determined. The categories modelled were air, waste, low-grade ore, medium-grade ore, and high-grade ore. The block model outputs either resulted in a proportional block model (categories expressed as percentages within equivolumetric blocks) or a sub-blocked model (parent block and one sub-block), which is the preferred block model output at the Savage River mine. When compared to the traditional best practice modelling method, which takes 43 work days, the wireframe-free modelling method took only 26 hours from initial modelling, using both exploration and grade control data. An update using appended drill hole data is achievable within one day. These results represent time savings of more than one order of magnitude compared to the traditional workflow, and, as such, these figures merit serious consideration for the use of the direct-to-block modelling approach at other operations.With these time savings, geological and estimation models can be kept updated constantly; geologists will not need to set aside two months for quarterly or half-yearly modelling of the drill hole data for resource review. Such dramatic time savings will allow for the better use of highly skilled geologists, who are in short supply in the current market, and will also impact directly on downstream mining engineering workflows.

Aug 22, 2011

By R. H. Schutz

This publication lists the respiratory protective devices approved by the Bureau of Mines as of December 31, 1968, and the names and addresses of their manufacturers. The purpose of this publication is to inform the public about approved equipment for safe use in mines and mineral and allied industries.

Jan 1, 1969

By Alan D. Akerman

This paper describes the significant advantages and improvements in operational availability, reduced breakdowns, and overall cost reductions that can be achieved through the application of a Reliability Centred Maintenance (RCM) program, including Condition Based Maintenance (CBM) and Equipment Health Monitoring (EHM), in a mine environment. It uses a case study to illustrate the essential elements that constitute the basic requirements to establish such programs. This CBM case study analyzed the Load-Haul- Dump (LHD) vehicle sub-systems and their dominant failure modes, as a precursor to the development of condition indicators. The case study describes a disciplined process to enable condition indicator development and qualification in support of a CBM program. The identified condition indicators vary from readily applicable off-the-shelf monitoring systems and techniques, through to "leading edge" technologies that require further research and development. The paper also explores the developments that have been made in the combination of expert system software associated with modern computer based control systems, and the availability of "intelligent? sensor technology that complement the control system capability.

May 1, 2002

By Daniel Tao, Jike Qiao, Hao Ren, Feifei Ji, Gonglun Chen

The floatation of niobite was studied using a number of collectors at various dosages and solution pH’s. Octyl diphosphonic acid was found to be an effective collector for niobite flotation with good selectivity. A flotation recovery of 91.2% was obtained with 140 mg/l octyl diphosphonic acid at pH’s less than 5.0. Infrared absorption spectroscopy (IAS) and X-ray photoelectron spectroscopy (XPS) were used to characterize the interactions of niobite with octyl diphosphonic acid. Species distribution diagram of octyl diphosphonic acid and niobium species was used to elucidate the flotation behavior of the mineral with octyl diphosphonic acid. A chemical adsorption mechanism of niobite with octyl diphosphonic acid was proposed. Keywords: octyl diphosphonic acid, electrokinetic measurements, niobite flotation, XPS.

Jan 1, 2005

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By Elli Nurminen

Keywords: Thermal conductivity of sulphates, flash smelting, heat recovery boiler, flue dust Accretions and build-ups in metallurgical heat recovery boilers decrease the efficiency of the heat transfer and may cause process shut downs. Transient plane source method (Hot Disk) has been applied to measure the thermal conductivities of the Copper Flash Smelting flue dusts. Thermal conductivities of copper, iron and zinc sulphates, and process flue dusts were measured. The results indicate that all the components are effective thermal insulators, having a thermal conductivity of less than 1 W/mK. Decreasing dust layer porosity has an increasing effect on thermal conductivity. Insulating layers on the boiler walls decrease greatly the heat transfer efficiency of the boiler. The gathered information will be used in CFD-modelling of the process, and in the process control.

Jan 1, 2005

1.1 The parties agree to submit all claims, disputes or controversies arising out of, or in relation to, the interpretation, application or enforcement of this agreement, including dispute resolution procedures, to sequential mandatory discussion, mediation and arbitration for resolution of all disputes before, and as a condition precedent, to self-help, arbitration, judicial action or other remedies. This mandatory procedure will resolve each dispute within one-hundred (100) calendar days. Any deadline falling on a federal holiday or weekend will be the next working day. Breach of this disputes process shall constitute a material breach of contract for which the aggrieved party may recover all costs, including attorneys fees, interest and other expenses necessary to resolve the dispute through litigation. The obligation to discuss and then mediate and arbitrate covers all disputes arising from every aspect of the Project to be built by the owner, including, but not limited to, design, engineering, bonding, indemnification, labor, material and services, and the acts or omissions of any related party for whom a party to this agreement may stand responsible.

Jan 1, 1994

By A. Deepatana

Bioleaching of nickel laterite ores is based on the use of heterotrophic fungi organisms and their metabolites (organic acids) to dissolve nickel and cobalt from oxide minerals to form metal-organic complexes. Metal recovery from this process using an aminophosphonic acid based chelating resin (Purolite S950) was investigated as a function of metal concentrations, complexing agent including citric, dL-malic and lactic acids. Batch adsorptions were conducted using synthetic leachate solutions of nickel and cobalt with concentrations from 15 to 2000 mg/L prepared in 0.01 and 0.1 M organic acids. Adsorption equilibrium data were interpreted using the Langmuir, Freundlich and Dubinin-Kagner-Radushkevich (DKR) models. The results showed that equilibrium adsorption data for nickel-organic complexes followed the Freundlich model and those for cobalt agreed with the Langmuir model. It was observed that the maximum adsorption capacities of nickel and cobalt were 3.26 and 10.48 mg/g resins respectively. These were achieved in metal complexes prepared from 0.01 M lactic acid. Metal elution was conducted using 2 M nitric acid. High metal recoveries were achieved from low metal concentrations but were found to decrease with increasing metal concentration. The results suggest that effective recovery of nickel and cobalt from low concentration of metals, such as those generated from bioleaching operations, can be achieved suitably using chelating resins.

Jan 1, 2006

By Harry Verakis, Thomas Lobb

In the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry and coal mining was the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past two decades. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. This paper is a summary and an update of the surface mine blasting accident investigations and studies conducted previously by the Mine Safety and Health Administration (MSHA) and the former U.S. Bureau of Mines.

Jan 1, 2001

By S. Todd Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty in factor of safety predictions for soil slopes where there is incomplete knowledge of the spatial distribution of soil properties. A case study considers a natural clay slope in Canada. The sequential indicator simulation technique is used as a means for generating a series of spatial maps of soil properties for this site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. Factor of safety determinations are then made for each simulated map using the simplified-Janbu approach, where the computations are performed with a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the distribution of factor of safety conditional to the type, position, and value of existing site characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1993

By Padmavathi V. Sagi

In this paper, effect of cyclic loading on the behavior of a long, flexible, unrestrained vertical pile loaded laterally in soft clay is examined. For cyclic loading, the analysis is carried out using a new method for the construction of p-y curves and for static loading conditions, p-y curves proposed by Dewaikar and Poonam (2005) are used. An iterative analysis is employed with secant modulus approach using a matrix method known as moment area method developed by Sawant et al. (1994). For pile top deflection of 20% of pile diameter, the load values are computed for both static and cyclic conditions. The comparison of results with the field test results reported by Matlock (1970) shows a good agreement. A parametric study is further carried out to examine the effect of load eccentricity, pile embedment length, diameter and the number of cycles on the pile response. The results of this study are discussed in the paper.

Jan 1, 2006