Search Documents

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009

By N. Grosland, G. Kopp, T. Hunstad, D. Wilder, M. Contratto, S. Rahmatalla, T. Xia

Chronic whole-body vibration exposure, as expected in large construction and mining vehicles, has been associated with neck and back pain and injury.1 While work has been done towards gaining a better understanding of the relationship between vibration and shock and muscle activity of the back musculature2, relatively little information regarding the activity of neck, shoulder and upper arm muscles is known. Today’s equipment designs must conform to domestic and international standards, however these standards do not specifically address the vibration exposure in the head and upper quarter. Further it is not well known how the control configuration within a vehicle (e.g. steering wheel versus arm controls) influences muscle voluntary and reflex activity levels. Greater muscle activity may lead to greater muscle fatigue – which in turn may be associated with greater risk of injury.2 Thus, muscle contractions needed to maintain static postures as well as those resulting reflexively should be considered during an analysis of seating position. Unfortunately, little is known regarding the influence of arm position on head and neck muscle function. The purpose of this study was to investigate the relative muscle activities of 5 neck, shoulder, and upper arm muscles during riding simulations of large construction equipment, using three different arm control options. Methods Five typical heavy equipment ride files were “played back” through a man-rated Servo Test 6-degree of freedom (dof) vibration system. Each ride was repeated using 3 seat and control configurations (steering wheel (SW), floor mounted arm-rest controls (FM), seat mounted arm-rest controls (SM)). Two trials were performed for each ride and seat control combination (each trial: 60 sec of 6-dof and 60 sec of vertical vibration). Five channels of surface electromyography (EMG) of the right-side cervical erector spinae muscles (neck extensors), sternocleidomastoid (neck flexor), upper trapezius (shoulder elevator), biceps brachii (elbow flexor) and triceps brachii (elbow extensor) muscles were collected throughout each ride (~ 2min) using pre-amplified (10x), 1 cm silver bar electrodes, with 1 cm fixed inter-electrode distances (Delsys, Inc). Further analog amplification was set at 10k (1k for one subject), and sampled at 1000Hz using a 12-bit DAQ card and Labview 7.1 software (National Instruments). A total of 7 right-handed male subjects were tested, but only 5 had complete EMG data sets to analyze for this sub-study. EMG was analyzed using root mean square (RMS, in mV) of 20 ms moving windows, and then averaged across the entire trial for a measure of mean total muscle activity (voluntary and reflexive). The muscle activity to maintain the static posture was estimated as the mean RMS EMG over a 1 sec interval just prior to and/or after completion of the ride. Repeated Measures ANOVAs were used to test for with-in subject differences using a = 0.05.

Jan 6, 2006

By E. Shekarchi

A year after the Soviet Union invaded Afghanistan and replaced President Amin with their choice, President Karmal, Afghanistan remained in turmoil. In some respects, the political and economic situation in Afghanistan was no better by the end of 1980 than it was preceding the December 1979 invasion. The Government faced widespread and growing alienation and resistance, virulent factionalism within the ruling party, and an acute shortage of material. The mining sector of the country did not fare better either; the only raw material produced in a significant amount was natural gas, which was exported mainly to the Soviet Union. No statistics on production of other minerals and materials were available by yearend. Most of Afghanistan's gas production was from the Hodja-Gugerdag Field, southeast of Shibarghan. The gas flow from this field had been about 300 million cubic feet per day since 1961. An estimated 230 to 250 million cubic feet per day of Hodja-Gugerdag's production was moved by pipeline across the Amu-Darya River into the Soviet Union. Most of the remainder was transmitted eastward to a 105,000-ton-per-year fertilizer plant and an electric power station built near Mazar-i-Sharif with Soviet assistance. After the Soviet invasion, the second gasfield, Djar-Kuduk, in the Shibarghan area, was brought under production. This field, which will produce about 200 million cubic feet per day, consists of four gas zones in the Jurassic and lower Cretaceous zones between 3,000 and 8.500 feet deep. The gas has a high hydrogen sulfide content, with considerable carbon dioxide, A new treatment plant was built at Djar-Kuduk by Soviet technicians under a turnkey contract at the end of 1980. It is believed that most of the Djar-Kuduk's initial flow will be sent to the Soviet Union.

Jan 1, 1982

Novel flotation reagents were developed to improve the flotation of coarse particles. Laboratory tests conducted on an anthracite coal sample from Kyung-Dong Coal Company, Korea, showed that the reagents can successfully clean 2?3 mm top-size materials. Pilot-scale tests conducted on a 1.41 mm x0 coal gave substantially better results than those obtained using kerosene as collector. The pilot-scale test results were used to develop a flowsheet, in which the 1.41 mm x0 fraction is cleaned by flotation and the 4 x1.41 mm coal is cleaned by single-stage spirals. The performance of this circuit was compared with another flowsheet, in which the 0.5 mm x0coal is floated using the conventional flotation reagent, with the 4 x0.5 mm material being cleaned using two separate spiral circuits. The performance of the two flowsheets was compared by computer simulation. The results showed that the flowsheet consisting of the coarse particle flotation circuit can give substantially higher yield sat a given product grade. Keywords: coal flotation, coarse particle flotation, collector, spirals, computer simulation.

Jan 1, 2002

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959

By Hal M. Lewers

IN the past few years and especially since the beginning of World War No. 2, gold has attained a new, important. and critical place in the international scene, and in world affairs. In the past, as far back as history records, most wars have been waged for the purpose of acquiring it from someone else by conquest. But now, the most titanic struggle of all time is being waged with the avowed purpose of not only destroying it, but of destroying all that it stands for and represents. A tradition dating back to ancient Rome, affirms that battles are fought by men with weapons, but wars arc eventually won by gold. The validity of that tradition is now being subjected to its major test. Hitler has proclaimed that in his new world order, the work dollar or reichsmark, a beautifully engraved paper currency representing only a theory of value, based on unit of work and production, will become the supreme medium of world exchange, and that gold eventually will he valueless and obsolete.

Jan 1, 1942

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By Massimo Concilia, Remo Grandori, Paolo Nardone

Paul Y. – SELI Joint Venture had been contracted to build the longest section of the Strategic Sewage Disposal Scheme (SSDS) – Stage I. This involved two tunnels under urban and marine areas excavated by high performance hard rock open type TBMs operated from deep shafts. A specific ground treatment program was developed using advance probing and grouting to control water inflow into the excavations. The article describes: the technologies adopted, the experienced problems, the encountered productions and their interrelation with the water inflow amounts, the possible improvement in the technologies for the excavation of the future stages of the same project as well of any other project under similar conditions.

Jan 1, 2001

By Betty Gibbs

The Ore Body Modeling and Mine Planning Worshop, sponsored by the Society for Mining, Metallurgy, and Exploration, Inc. (SME), was held Feb. 22-24, 1991 before the SME Annual Meeting and Exhibit in Denver, CO. More than 40 people from mining companies, government agencies and universities attended. Eight vendors of integrated ore body modeling and mine planning software attended and presented the results of problem sets given before and during the workshop. They were: [ ]

Jan 1, 1991

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By Libby R. Ricafort, Victorio V. Pato, R. S. Pizarro

Introduction Atlas Consolidated Mining and Development Corp. (ACMDC) started gold production at its Masbate gold mine early in 1980. This involved an open-pit mine and a 3.5-k/d (3850-stpd) carbon-in-pulp processing facility (Pizzaro and Antonio, 1981). When this operation started, the mine began stockpiling sub-grade milling material averaging 1 g/t (0.029 oz per st) gold. Furthermore, geologists estimated that there were additional low grade reserves within the ultimate pit limits. These amounted to 2.4 Mt (2.6 million st) with an average grade of 1.1 g/t (0.03 oz per st) gold. The success of low cost heap leaching prompted an investigation to determine if this tech¬nique would be applicable for the low grade Masbate ore. The findings were favorable and a series of laboratory tests were undertaken. These tests indicated the amenability of this subgrade milling ore to heap leaching. Depending on ore size, gold extractions of more than 60% were obtained. To further define operating parameters for a commercial heap leaching plant, a 400-t (440-st) batch pilot plant was built and operated. These test results were used to design the first commercial heap leaching plant in the Philippines. One design concern was the control of solutions during the rainy season. Due to the material's low grade, every effort was made to minimize capital and operating costs. To this end, surplus mining equipment from the copper operations of ACMDC and used machinery in the crushing circuit were considered. Location: The Masbate gold heap leaching operations are located on the northeastern part of Masbate Island, Philippines. This is about 480 km (300 miles) south-east of Manila. Climate: The climate is moderate with two distinct periods. The dry season runs from January through June, and the rainy season extends from July through December. During the wet season, the rainfall at the mine site averages 300 mm/m (11.8 in. per month) for a total of about 2000 mm/year (78 in. per year). However, heavy downpours in excess of 100 mm/h (4 in. per hour) can occur. Geology: Four distinct rock types have been identified in the pit area. They are tuffaceous agglomerates, andesitic agglomerates, metasedimentary rocks, and hornblende augite andesitic porphyry. The tuffaceous agglomerate occupies the northern and western flanks of the mine. Andesitic agglomerates are localized distinctly in the central portion of the volcanic plug within the mine site. The eastern boundary of the mine is occupied by metasedimentary rocks, whereas, the hornblende augite andesitic porphyry occurs as an intrusive within the andesitic agglomerate and tuffaceous agglomerate. Some areas of the pit contain high proportions of clay minerals, requiring an agglomeration step in the flowsheet. This ensures satisfactory percolation through the heaps. Ore characteristics: Gold and silver are microscopically dis-

Jan 9, 1987

By G. A. Craig

The Moon, asteroids, and planets of the solar system represent the most distant caches of wealth that humanity has ever considered recovering. Yet, in addition to the potentially recoverable values represented there, harvesting off-Earth resources has a second, almost incalculable sustainable benefit in that they can be retrieved with absolutely no damage to Earth. Previous research mostly assessed the potential of asteroids and the Moon for mining purposes from a theoretical and scientific point of view. These studies investigated drawbacks that could be experienced in this type of operation, but no detailed economic evaluation that is meaningful for mining project management has been conducted and the parameters that are most likely to make an operation feasible are unknown. This paper provides a preliminary economic and sensitivity analysis of a possible off-Earth mining business extracting minerals from an existing asteroid.

Jan 1, 2014

By B. Roy

The Somita plant processes low sulphide gold ore in Burkina Faso with a CIL process. After experiencing recurrent low gold recoveries, Somita undertook an investigation on the source of the problem. COREM conducted a mineralogical study on different pit samples. A series of tests was also conducted on a composite sample from the plant which shows a content of 3.4 g/t in gold and 0.48 % in graphite. A reference test in laboratory resulted in a recovery of gold of 75%, similar to plant recoveries for the evaluated ore. In these tests, even if cyanide is not deficient, it was diverted mainly into iron cyanide complex, copper cyanide complexes and by graphite adsorption. Causes of low recovery were also identified and quantified. Solutions to increase gold recovery were suggested such as increasing gold dissolution kinetics by O2 or by lead nitrate addition, change in activated carbon addition point location to the 1st cyanidation tank and finer grinding to increase liberation. Increase in the pH could also contribute to reduce cyanidation consumption. Following these recommendations, Somita changed carbon addition from tank 2 to tank 1 in the CIL circuit. This change led to an increase of more than 5% in gold recovery. A system for the addition of lead nitrate is also under implementation at the plant and benefit will be evaluated in 2013. Finally, pit management for cyanidation will be done based on mineralogy instead of gold content in the future.

Jan 1, 2014

Research 86 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1986

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has been conducting re-search to determine the influence of mining machine mounted water sprays on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery. Airflow speeds and directions were measured at several locations near the face with ultrasonic anemometers. Methane was released from the face and concentrations were measured in the entry at locations above the mining machine using fixed point methanometers. Changes in airflow speed, direction, and methane concentrations were correlated with water spray operations. The test results using different spray arrangements and water pressures showed that operation of the machine-mounted sprayers can improve face ventilation effectiveness by increasing the velocity of airflow moving toward and away from the face. The improved ventilation resulted in reduced methane levels near the face.

By Murali M. Gadde

Welded wire mesh is the most commonly used skin control technique in the United States underground coal mines. Currently, selection of the mesh is based on trial and error rather than any rigorous design methodology. Several factors affect a wire mesh?s performance including the amount of rock material to be supported and how the load is distributed, wire gauge, aperture size, grade of steel, weld strength, bolting pattern and sheet size. Although the best way to choose the mesh is to conduct full-scale physical load tests, because of the limitations on the number of variables that can be considered in such tests and the requirement of an elaborate test set-up, it may not always be possible to use this option. An alternative would be to use numerical modeling to study the load-deformation behavior of a wire mesh. In addition to providing a very detailed stress, strain distribution in the entire mesh, the advantage of this approach is the ease with which parametric studies can be conducted. In this paper it is shown that the load-deformation curves generated by nonlinear numerical models match closely with laboratory derived ones. Then, based on parametric studies, design guidelines are developed to choose the mesh appropriate for different loading conditions. The modeling studies also bring forth the limitations of the current lab studies. For example, under some conditions it was noticed that the small sheet size considered in lab tests would produce higher mesh deformations than a full-size one used in actual practice.

Jan 1, 2006

The OptiPit® software program is developed based on expertise gained at the Colorado School of Mines (CSM) using Mixed Integer Linear Programming (MILP) techniques. This program has been developed to satisfy the need in the mining industry for a multi-time period schedule and cutoff grade optimization tool that handles large scale open pit and underground mining operations involving many dumps, stockpiles, complex processing options and blending requirements. The current software (or earlier development versions) has been beta tested and used on various large scale projects within Placer Dome Inc., Newmont Mining Corporation, and Phelps Dodge Corporation since 2003. Through the use of this software, these companies experienced additional value creation by optimizing mine sequences, cutoff grades, material process flows and stockpiles under complex operational and processing constraints. This paper will present simple case study results to demonstrate the power of OptiPit® when used as a cutoff grade optimization tool. Furthermore, the paper will show, by example, how significant the difference in the Net Present Value (NPV) of a given project can be, depending on whether results are obtained by way of cutoff grade optimization using OptiPit®, or by using traditional breakeven cutoff grade approach.

Jan 1, 2007