Search Documents

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

By A. C. T. Bigg, Y. Kocak, N. K. Bodur

The Gumuskoy silver mine, owned by the Etibank, in the province of Kutahya, Turkey, has been operating since 1987 with primary, secondary and tertiary crushers, and two parallel single stage ball mill circuits. Continuing problems with crushing and feeding of the ore to the ball mills, because of the moisture retaining and sticky nature of the ore, prompted an investigation into the possibility of converting the grinding circuit to an autogenous or semiautogenous grinding circuit. This would remove the bottleneck associated with the secondary and tertiary crushing. At the same time the target feedrate is to be raised from 140 t/h to 175 t/h. This paper demonstrates the response of five ore types, and blends of ore types in an onsite pilot plant test program, and also suggests how the variations can be handled in a SAG mill/ball mill circuit incorporating just one of the present ball mills.

Jan 1, 2000

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

By S. K. Bradford

(Pittsburg Meeting, March, 1910.) FOR years past I have traveled in quest of promising mining-properties, over almost impassable mountain-trails to remote places in the mining-regions, usually, many miles from an assay-office. If, upon examination, the formation and the ore-deposit appeared favorable, a quick determination of the value of my samples was necessary, in order that I might take intelligent action with reference to the acquisition of the property. A journey with my samples to civilized regions often meant weeks of delay, and perhaps loss of opportunity. How many, under similar circumstances, have returned with their assay-results from such a journey, only to find that some audacious speculator had " optioned" the property ! True, a first payment could have been made and the chances taken on the results; but experience has taught that rich-looking ore is not of necessity valuable. Personally, I would not hazard a ten-dollar bill on any property without first determining by assay the value of the ore. To carry the usual complete assay-paraphernalia over such mountain-trails was impracticable by reason of the loss of time involved, the great expense of transportation (charged according to weight), and the fact that a few such trips would almost certainly wreck the outfit. For these reasons I began a process of elimination and substitution which finally enabled me to carry, in an ordinary 26-in. valise, sufficient apparatus and supplies for, say, 100 assays of adequate commercial accuracy. My final outfit was as follows: APPARATUS. Small hammer; steel mortar (2.5 in. wide, 3 in. high, with stand sawed off flat, so that it can be used as an anvil and for

Jan 1, 1911

The #3 Shaft at Brunswick Mine, Bathurst, New Brunswick, Canada, intersects a soft graphite zone just below the 3400 Level. Ground movement within this zone causes the concrete liner of the shaft to be deflected towards the shaft?s interior, affecting the steel framework of the conveyance. In some areas, the clearance between the cage and the liner has been reduced to less than 2 cm, which is a concern. An innovative surface-mounted extensometer was designed in 2008 to monitor potential movements of the shaft?s liner. Four such novel extensometers were installed in the shaft for the surveillance of a particularly critical 3.0m by 5.5m area. This article describes the approach taken to instrument the shaft, the principle of the new extensometer, as well as the performance of the instrumentation following its installation.

May 1, 2009

By Godofredo Torreblanca

El presente trabajo identifica, inventaria y estima los montos de inversión de los “peligros históricos” que conforman los “pasivos de seguridad” en la unidad de producción Morococha, -en tanto, representan las mayores causas ocultas de los incidentes /accidente, de forma que priorizan el nivel de riesgo que representan para tomar las medidas preventivas y crear un sistema de gestión de seguridad. De otro lado, los pasivos se han codificado para facilitar su administración y seguimiento, en aspectos relacionados con posibles fallas en el diseño de las instalaciones, peligros por antigüedad de equipos y herramientas, peligros por infraestructura minera defectuosa, y todo aquello que pueda representar un riesgo para los trabajadores (labores con secciones reducidas, tajeos sin chimeneas de ventilación, equipos defectuosos o inadecuados, instalaciones inadecuadas, instalaciones eléctricas sub estándares, etc.).

Sep 14, 2009

By W. Stumpf

Mill log analyses and complementary hot deformation studies were carried out on the as-cast structure and on a hot rolled structure of the same low carbon steel (SAE 1006) that had been processed according to the direct or hot charge route in a compact strip plant. The main softening mechanisms during hot rolling were found to be complete dynamic recrystallization during each pass above about 1000°C for the as-cast structure with an austenite grain size of 277µm and, secondly, incomplete static recrystallization after each pass with a finer austenite grain size of about 26 µm and tested below 1000°C. A two-stage hot working mechanism has also been found by others on a similar steel also processed by the hot charge route and this may appear to be a characteristic of this type of material. Constitutive constants determined from hot working studies were combined with other constants from the literature and incorporated into a grain size development model that correctly predicts the final ferrite grain size in the hot rolled strip steel. The predicted incomplete static recrystallization during the last three finishing passes in the plant appears to result in some retained strain in the hot rolled austenite as it transforms to ferrite on the run-out table. Analyses with the model predict relatively little sensitivity of the final ferrite grain size to process and product variables such as temperature and strain per pass for the last three passes and also the starting austenite grain size in the slab. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, ferrite grain size, grain size modelling.

Jan 1, 2003

Introduction The science of geometallurgy requires that ore characterization be performed holistically, that is, with consideration of ore quality on plant performance and product quality. Geometallurgy, by definition, requires knowledge of geology, mineralogy, extractive metallurgy and pyrometallurgy. Examples of the ore characterization challenges for the geometallurgist in the production of iron ore pellets from low-grade Proterozoic iron formation are presented here. Ore Characterization Ore characterization, the quantifying of mineralogy, grain size and the texture of ores, is an often overlooked tool in improving process efficiency. Some mineral related problems are not unique to the production of iron ore pellets; e.g. the problems caused by expanding clays in flotation. The negative impact of carbonate minerals in the ore on pellet productivity and pellet quality are unique. The long and complex geologic history of Precambrian iron formations contribute to modifications of grain size and the introduction of complex textures.

Jan 1, 2007

By J. W. Thompson

That the governor is hereby authorized to appoint a commission of seven persons, to be known as the industrial accidents commission-two of whom shall be employers of labor, two of whom shall be employees in either mines or industrial establishments of this Commonwealth, or duly accredited representatives thereof, two of whom shall be learned in the law, and one of whom shall be a person skilled and experienced in making investigations-to inquire into the causes and results of industrial accidents in the mines, mills, factories, stores, and upon the railroads, street railways, ships, wharves, and in all industrial establishments, and in all other places where men, women, and children are employed in manual labor in this Commonwealth; to study the most advanced methods for safe-guarding against these accidents; to inquire into the subject of fair compensation for those who are injured in these accidents, and for the families of those who shall be killed as a result thereof; and to study the operation and effect of the Workmen's Compensation Law of 1913. SEC. 2. The chairman of said co~mission shall be designated by the governor, and the person named on said commission as a skilled and experienced investigator shall be the secretary of the commission, The commission shall have power to employ such legal counsel and other officers and employees as it may deem necessary to properly perform its duties. SEC. 3. The secretary of said commission shall receive an annual salary of $2,400 and his actual necessary expenses; and the other members of the commission shall receive no compensation for their services, but shall be allowed their actual traveling and other necessary expenses. The salaries of any other persons employed by the commission shall be fixed by it.

Jan 1, 1920

By E Apaza, R Neumayr

This paper aims to summarise the discovery of the QTS Central resource, a previously unidentified +1 Mt inferred resource that lies between two major CSA resource systems.The 1.7 Mt at 5.76 per cent Cu, QTS Central ore system represents 1/6th of the CSA mineral resource and was discovered in 2014 based on the accumulation of historic exploration records dating back to 1989.The CSA deposit consists of five ore systems hosted within turbidite-derived siltstones (CSA Siltstone) and lesser sandstones (five per cent) of the Devonian Amphitheatre Group. The host sediments strike approximately north–south with a steep westerly dip and exhibit a well-developed east dipping cleavage. Most CSA mineralisation is hosted within dilation zones at the intersection of cross-cutting structures and is interpreted as epigenetic in origin.Alteration and weak mineralisation, up plunge to the reported QTS Central mineral resource, was initially detected in 1990 during a downhole electromagnetic conductivity (EM) study, where one hole indicated an off-hole conductor, later tested with four diamond holes. One of these diamond holes intersected 3 m at 7.5 per cent Cu at 200 m. Development of the 9070 Subway drive in 2005/2006, linked the QTS North and QTS South workings and intersected structures interpreted to host QTS Central mineralisation. Subsequent drilling proximal to the 9070 Subway in 2007 identified an up plunge extension to the QTS Central zone (UDD07152: 1.8 m at 6.3 per cent Cu from 10.7 m). Work on QTS Central was largely forgotten until 2012 when the mining of a 450 m infrastructure drive provided a platform to test the anomalous grades. In December 2013, drill hole UDD13055A intersected 20.9 m at 7.2 per cent Cu from 378 m. By the end of 2014, the QTS Central inferred resource was 1.0 Mt at 6 per cent Cu and 18 g/t Ag (Hosken and Apaza, 2014). Late in 2016, further infill drilling occurred from two fronts to increase confidence in the QTS Central resource. The results of this drilling are expected late in 2017.The current interpretation indicates the QTS Central system consists of two main lenses hosted within closely bedded sandstones and siltstones. The sandstone in general is not mineralised, being heavily silicified, while the siltstone is mineralised and chloritised. The main mineralised lens is 75–200 m along strike and 450 m high. Massive sulfide feeder structures lie at the core of the two main lenses, although the characteristics of the QTS Central system tend toward the mineralisation being more chlorite-rich than in QTS North and QTS South.CITATION:Apaza, E and Neumayr, R, 2017. The discovery of the QTS Central ore system, CSA mine, Cobar, NSW, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 151–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R. J. Fruehan

Slags have many useful functions in iron and steel making. In particular, slags are used to remove impurities such as sulphur, phosphorus and inclusions from the metal, and a large amount of research has been done in this area. Slags also insulate the metal thermally and form reactions with the atmosphere such as reoxidation and nitrogen pick-up. However, slags serve other more unique functions, several of which are reviewed in this paper. The role of slags in new iron smelting processes with regards to reduction of ore and gaseous desulphurization are discussed. In iron smelting processes, much of the reduction occurs by the reaction of carbon in the char and the metal suspended in the slag with iron oxide dissolved in slags. The slags also react with the gas resulting in sulphur removal from the process. The mechanisms of these reactions and pilot plant data for these processes are given in this paper. Slag formation within ferrous burden materials affects the cohesive zone and the performance of the blast furnace. Recent theoretical and experimental findings on this topic are presented. In the electric arc furnace, foamed slags are used to allow for higher power operation and productivity. Of particular interest, foaming in stainless steel production is more difficult than for normal steels. The foam index, or the ability of the slag to foam, for stainless steelmaking is similar to that for carbon steelmaking slags. The poor foaming is due to the lack of gas generation for the foam. Methods to increase foaming in stainless steelmaking are discussed.

Jan 1, 2004

By Clayton M. Rumsey

In 1984, the U.S. Bureau of Mines conducted a mineral survey of a 26,598-acre study area which includes the 23,702-acre Mt. Limbo Wilderness Study Area (NV-020-201). The study area is 65 miles northeast of Reno, NV, and is underlain mainly by Cretaceous granodiorite that comprises the Selenite Range. Tertiary basalt, rhyolite, and sedimentary rock as well as Quaternary alluvium and lake deposits are exposed near the study area boundary. Mines just north of the area in the Hooker mining district produced tungsten ore in the 1940's and 1950?s. Similar deposits are not known in the study area. Disseminated gold is in sinter about 6 miles west of the study area and at several other locations regionally.

Jan 1, 1986

By Hiroaki Sakurai

Using batch reactors equipped with CO and CO2 gas sensor, CO oxidation over Au catalysts in room air has been investigated and compared with Pt catalysts. For both Au and Pt catalysts, the logarithm plot of CO concentration data during initial 10 min are well fitted by straight line, which mean the first order dependence on the CO concentration between 10 and 10,000ppm. The rate constant value (k) over Au and Pt catalyst generally decrease with increasing initial CO concentration above 100ppm. The value decrease especially rapidly between 100ppm and 1,000ppm over Pt catalysts, which should be due to the strong adsorption of CO on Pt. The k value over Au catalyst has become ten times or more as large as the Pt catalysts at 1,000ppm. Already for the initial concentration of 100ppm CO, the strongly adsorbed CO on Pt metal has been clearly observed by FT-IR during the reaction over Pt/Al2O3. A part of the strongly adsorbed CO has been remained on Pt after the disappearance of gas phase CO, and has gradually changed to gas phase CO2. Such strongly adsorbed species on Au has never been observed on Au/TiO2 under the same reaction conditions. These features of Au catalysts are favorable for indoor air purification.

Oct 1, 2003

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By Pierre Pelletier, Christian Pichetie, Dany Pelletier

"IntroductionDuring 1994, Barrick Gold Corporation, or American Barrick at that period, acquired Lac Minerals Ltd. properties. One of them was the Bousquet Complex. The Bousquet Complex is divided into three distinct sites: one mine (Bousquet 2), one mill (Est-Malartic Division) and one analytical chemistry laboratory (Les Terrains auriferes).The Bousquet 2 orebody was discovered in 1986. An extensive drilling program was initiated during 1987. Its purpose was to define the orebody extent. At the end of 1997, gold production from Bousquet 2 mine reached 1 290 000 oz of gold from a cumulative tonnage processed of 4 175 000 M t.From 1980 to 1990, the Est-Malartic mill was used for the treatment of ore from the following mines: Bousquet 1, Doyon, Francoeur (Richmont mines), Buckshot and 1-20 stope. At present, the mill receives ore from the Bousquet 2 mine.HistoryThe Est-Malartic mill is located close to the town of Malartic in northwestern Quebec. The mill has been in production since the mid-1930s processing mainly clean, free mill gold ore. Active mining from the Est-Malartic mine ceased in 1979 and the mill was switched to custom processing of ore from La Mine Doyon located some 45 km to the west. This custom processing arrangement continued until 1987 when the expanded mill at Doyon became available to process all of the Doyon production. In 1987, Lac Minerals commenced development of a second mine at the Bousquet site located 40 km west of Malartic. This mine, Bousquet 2, is the down dip extension of the La Ronde mine developed by Agnico Eagle. During pre-feasibility evaluations, it was determined that it would be economically more attractive to modify the existing Est-Malartic mill than building a new facility on site. The Est-Malartic mill modifications for processing the high-copper/gold ore from the Bousquet 2 mine began in late 1989 and new circuits were commissioned in mid-1990. Modifications included the addition of both gravity and flotation concentration circuits to recover coarse, free gold and the copper. The existing leaching circuit continued to operate on the copper flotation tailings with some minor modifications to the solution handling systems. A S02/Air cyanide destruction circuit was also added at that time."

Jan 1, 2000

After the closure of collieries, they naturally start to fill up with water. As a result, hydraulic gradients develop between them and different hydraulic pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The collieries in the Witbank Coalfield have geometries such that there are several areas where this intermine flow is possible. Since the Department of Water Affairs and Forestry has declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon is required. The challenges in determining intermine flow are numerous, and attention has focused on identification of areas where these flows can take place. The quantification of these flows is problematic due to the uncertainties in exact geometric configurations and the variation in site-specific hydraulic properties of thecoal and overlying lithilogical layers. During this study, use has been made of numerical flow modelling and several analytic solutions to test the applicability of the flow models as well as to predict groundwater flow directions, filling times of voids and flow volumes. The numerical modelling methodology entailed a downscaling approach starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines, and finally looking in detail at the major areas of interaction.

Jan 1, 2005

By W. Blake, J. Whyatt

Sixty years of rockbursting in the Coeur d’Alene district has taught painful lessons and led to a number of practical advances in controlling rockburst hazards. This paper summarizes those lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rockburst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rockburst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d’Alene district experience.

Jan 1, 2002

By D. M. MacHunter, M. K. Palmer

Refinement of design parameters and features has resulted in the development and commercialization of spiral separator models that offer enhanced performance for a number of application areas. Examples of recently developed spiral separator models include the enhanced performance (EP)spiral and the HC (high capacity) series. Comparative performance data for appropriate applications are presented for each of these new model spiral separators. The utilization of spiral separators providing improved performance offers significant cost and operational benefits for process plants. Examples of process flowsheet changes that have resulted from the incorporation of recently developed spiral separators include the reduction of the number of process stages and the achievement of high density tailings by the utilization of a dewatering arrangement in the spiral tailings splitter system.

Jan 1, 2003