Search Documents

By B. Lueger, D. Shen, M. Sedighy, R. Rand, R. Saleh, J. Cheung, M. Rifai, I. Khan, W. Sauri, D. Setianto

The world’s first active power demand stabilization system for a 3-electrode electric arc smelting furnace was commissioned at PT Vale Indonesia in December 2012 on Furnace No. 2 using an SPLC (Smart Predictive Line Controller). The SPLC technology in combination with the Furnace No. 2 rebuild and other upgrades has enabled PT Vale to increase the electrical input to the furnace by up to 20% on a stable and sustainable basis by eliminating peak powers that overload and trip out the electrical equipment, and by reducing power unbalances. The SPLC technology maintains smooth arc power using a continuously variable thyristor controlled series reactor. The SPLC compensates variations in the furnace arc with predictive changes in the circuit reactance at a speed of up to 60 times a second. The system started up quickly and has been shown to be easy to operate and maintain by PT Vale. PT Vale’s Operations Team has been testing the new system at set points of up to 90 MW on the newly re-built Furnace No. 2. Over the last 12 months, the throughput of Line 2 has increased by approximately 10% on an annual average; however, debottlenecking in other design areas of the operation is required in order to achieve 90MW operation on a sustainable basis. This outstanding success results from a combination of the furnace and other upgrades, the SPLC active power stabilization, and the skill of PT Vale in quickly adopting new technologies and maximizing the combined benefits of each technology in their operation.

Jan 1, 2014

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By Gordan Marrs, O. Matwijenko

"The Kidd Creek metallurgical site has been highly integrated to maximize revenues from its base metals mines. The site's operations include a Concentrator processing 4.3 million tonnes per year of copper-zinc ore, a Copper complex producing 100,000 tonnes per year copper cathode and a Zinc Plant producing 130,000 tonnes per year of zinc metal. To improve operating efficiency with increasing emphasis on productivity, process control, process automation and process optimization have been augmented and expanded during the last decade.New microprocessor based control systems provided the opportunity for the capturing of an expanded number of process related measurements. As supervisory computers were already in place, databases could be generated with only increased disc space and database management programs required. Once the data had been accumulated and stored, a method was then required for handling, screening and sorting large volumes of information in relatively quick and easy terms in order that the stored information could be used. By 1984, a decision to use personal computers for accounting, engineering and management reporting provided the vehicle necessary to handle this data. Using commercially available software, large volumes of stored process data can be downloaded from existing databases, filtered, sorted, analyzed, graphed, displayed, projected, reported and distributed. All this can be performed in very little time."

Jan 1, 1989

By B. Goard

"IntroductionCemented backfill has been placed underground in slurry form in Inco Limited's Ontario Division mines since the early 196Os. The slurry was traditionally mixed on surface at between 65 and 70 wt% solids* and transported underground via gravity through a borehole-pipeline distribution system. This method of placement, while simple and dependable, has proven to be costly because of the large amounts of transport water involved.A significant quantity of the slimes buildup on mine levels is caused by the backfill water carrying cement and other fine material out of the stopes. The level cleanup and eventual pumping or hoisting of the slimes and water back to surface result in substantial indirect backfilling costs.The cement that remains in the stope is always overhydrated because of the high water cement ratios that exist. As a consequence, high concentrations of Portland cement must be added to the backfill to produce the fill strengths required for the different mining methods.Pouring backfill at these densities also demands extensive fill preparatory work in the stopes to withstand the hydraulic heads created by the slurried fill. This, along with the delays in pouring necessary to allow for water drainage, result in significant losses in productivity.These negative aspects of slurry placed fill has led Inco Limited to investigate several methods of transporting backfill underground via pipeline, at higher densities (i.e. 75 to 95 wt.% solids). Three separate transport methods are presently being experimented with by the Company's Mines Research Department. Each utilizes a different technique or form of flow transport, i.e. concrete pumping technology, high density slurry flow, and pneumatic conveying."

Jan 1, 1987

By P. H. Davenport

"The ore-element patterns in regional lake sediment geochemical survey data from four areas of Newfoundland containing granite-related mineralization reveal characteristics which can be used to identify mineralized granitoids. The St. Lawrence Granite with its fluorite deposits, the Ackley Granite with molybdenite mineralization, the Grey River tungsten lodes and the newly discovered Mo- W mineralization at Granite Lake, Central Newfoundland, have all been included in the regional lake sediment geochemical surveys, which now cover about 90,000 km2 of the Island of Newfoundland. The lake sediments over these mineralized granites show diagnostically high values of Mo, F, Pb, Zn and, in three of the four cases, U, together with locally high Ag and Cu values. Furthermore, these ore-metals display a distinctive zoning pattern about the intrusives, which can be related to the classical ore-metal zoning patterns developed about many types of mineralized granitoids.IntroductionGranitoids in Eastern Canada are receiving renewed interest as potential hosts of tin, tungsten, uranium and related mineralization. Although a number of mineral deposits and showings have been known from a few granites (sensu lato) in the region for many years, granites had generally received little attention as potential hosts of metallic mineralization until the recent resurgence in interest in the mineral potential of these rocks. In Newfoundland, where granitoid rocks underlie about 30070 of the land area, petrologic data are available from some granites, particularly those in eastern Newfoundland (Strong et al., 1974; Strong, 1980), but in southern and southwestern Newfoundland the data base is sparse, and indeed in many cases individual plutons are not delineated on the geological maps of the area . Most of the available data on Newfoundland graniotolds have been summarized by Strong (1980), who gives a general assessment of their mineral potential by comparing their physical, mineralogical and petrochemical attributes with mineralized granites elsewhere in the world."

Jan 1, 1982

A rough simulated borehole has been developed for the installation and dynamic testing of rock bolts a the WASM Dynamic Test Facility. The rough simulated borehole is used for rock bolts that are sensitive to equipment installation technique or borehole geometry (particularly friction rock stabilisers and resin encapsulated bolts). An extensive axial test program has quantified a difference between the static and dynamic capacity (kN/m of embedment) for friction rock stabilisers once sliding starts. The 47mm split tube bolt has a 50% reduction in embedment capacity (but with significant variation) dissipating 2.7kJ/100mm of sliding per meter of embedment, and the Omega (inflatable) bolt had a 70% reduction in embedment capacity dissipating 6.2kJ/100mm of sliding per meter of embedment. The Omega bolt dynamic capacity remainder at least equivalent to the split tube bolt static capacity.

May 1, 2009

By Cz. Mora, A. Pawelczyk, D. Hreniak, P. Nowak, A. Dyonizy, S. Strek, W. Strek, K. Grabas, A. Ostrowski

Globalization and a growing demand for limited raw material resources have forced changes in the approach to the supply chain. This is particularly true in the case of rare earths, which are regarded as one of the most important development indicators of modern technologies. To ensure a secure supply of commodities, the European economies have been prompted to investigate REE recovery from sources which until recently, for technical or economic reasons, were considered not sufficiently attractive. An interesting example is apatite phosphogypsum waste dumps. The REE content in these waste dumps averages around 0.5-1 %. One of the most important phosphogypsum locations in Poland is the Lower Silesia region where a phosphoric acid Chemical Plant "Wizów" operated for several dozen years. In this work, rare earths are leached from the phosphogypsum crystalline structure by a chemical treatment and can then be separated into individual chemical compounds. The technology used in these recovery tests, matches up to a coherent European raw materials policy supporting effective management of resources and promoting waste materials recycling.

Jan 1, 2014

By K. Lundholm, A. E. Mäkinen

"Ore grades are declining and getting more complex around the world which not only complicate the ore processing but also produce new type of requirements to manage the produce waste streams. One specifically problematic and increasingly identified element in waste streams produced in mining and metallurgy is arsenic.Arsenic is a compound that has no significant market value, but that needs to be removed from ores, concentrates and other process streams because of environmental or process technical reasons. One example of a removal process is partial roasting of high-As sulfide concentrates, originally developed by Outotec. In this process the arsenic is volatilized in the gas phase and thus separated from the solid material, i.e. the calcine. If the arsenic is recovered by wet methods the process gas is quenched and all arsenic needs to be stabilized in the effluent treatment plant.Outotec has developed ferric arsenate precipitation as a method to produce stabile arsenic residues from wet gas cleaning effluents. Iron based precipitates, when correctly produced, can meet typical landfill criteria measured with different types of leaching methods meant for characterizing the arsenic dissolution behavior from the precipitates.In this paper partial roasting of sulfide concentrates with arsenic volatilization in combination with ferric arsenate precipitation is discussed from the perspective of producing wastes that can meet the stability requirements set by common leaching tests methods, TCLP and CEN. These leaching test methods set the normative landfill requirements for most operations generating arsenic containing wastes. A typical flow sheet of Outotec® Ferric arsenate process is discussed with results showing the importance of correct process control and sequence on producing arsenic containing waste that can meet the landfill disposal requirements."

Jan 1, 2014

By K. M. Tompson, R. L. Armstrong, C. I. Godwin

"Tungsten skarn deposits on the Clea property in the Selwyn Mountains, Y. T., are related genetically to a quartz monzonite stock, about 500 metres in diameter at the surface. Lower Paleozoic sedimentary rocks are metamorphosed for a distance of 3 km from the stock. Tungsten-bearing skarn mineralization within the altered sedimentary rocks is of two types: sulphide-rich pods and calc-silicate beds. The most significant scheelite concentration is in calc-silicate beds near or adjacent to the quartz monzonite stock. Discordant K-Ar and Rb-Sr isotopic dates indicate that the stock is probably of early Late Cretaceous age, 94 Ma or slightly older, and that it cooled slowly. High initial 87Srl86Sr ratios and disequilibrium relationships between K-jeldspar phenocrysts and groundmass minerals in the porphyritic phase of the granitic rock , and between different granitic rock specimens, indicate contamination of crystallizing magma by old sialic continental crust which extends westward under the Selwyn Basin.This study is significant to regional tungsten exploration. Granitic rocks associated with tungsten deposits, in this part of the Canadian Cordillera at least, appear to have specific isotope characteristics that indicate they were generated at a specific time and in a particular way.IntroductionThe Clea tungsten skarn property (Fig. I) is owned by Canex Placer Limited, and lies in the Selwyn Mountains (Bostock, 1948) near the eastern margin of the Selwyn Basin (Wheeler and Gabrielse, 1972), Yukon Territory. The property covers a 20-square-mile area centered near latitude 62°47 ' north and longitude 129°52' west, and is accessible by helicopter. An airstrip and the terminus of a summer-use gravel road at MacMillan Pass, Yukon, are about 20 miles to the northnorthwest.This paper deals mainly with the geochronemetry of granitic rocks from a stock associated with tungsten mineralization on the Clea property. We show that these rocks have specific characteristics that not only define the genesis of this stock, but also have significance for regional tungsten exploration around plutons in the Canadian Cordillera."

Jan 1, 1980

By Raymond C. Voige

"The use of current electronic technology in the design of new underground mine communications equipment is providing improved and expanded voice communications which can, in turn, contribute to improved productivity and safety. A review of equipment that is now available or under development Includes the following categories:WIRED SYSTEMSI.Pager phones with selective calling, audible and visual alerting and message indicator.2. Mufti-conversation pager phones that use multiwire cable ormultiplexing techniques.WIRELESS SYSTEMSLow-and medium-frequency inductive systems utilizing ""near"" magnetic fields for both vehicular and personal communications.Wired SystemsCommunication systems in underground mines have evolved slowly in many parts of the world. For many years, magnetotype telephones were the only means of communication from one mine level to another and to the surface. These units were located near the shaft and communications to the working areas were limited."

Jan 1, 1981

By J. Shang, P. Howarth, B. Morris

Tailings from the nickel refinery in Copper Cliff, Ontario, consist of fine silicates mixed with a variable amount of conductive and magnetic minerals mainly associated with sulphides and iron oxides. Subsequent oxidation of sulphide- rich phases within the tailings results in the formation of an acidic leachate that may contain significant concentrations of trace metals. Mapping the spatial distribution of regions of higher sulphide concentration therefore provides insight into the distribution of the acidgenerating potential within the tailings. Electrical conductivity is constrained by two parameters — the concentration of metallic sulphides and the ionic concentration of acid in groundwater. Magnetic susceptibility is directly related to the pyrrhotite and magnetite content. It is proposed that combining information derived from airborne electromagnetic and magnetic surveys can provide an indication of metallic sulphide distribution. Preliminary investigations of airborne electromagnetic and magnetic data acquired concurrently over the sulphide-rich Copper Cliff tailings site reveal that these parameters can provide information on mine tailing extent and permit separation of tailings with varying compositional and alteration levels. Airborne geophysical data provide information about the subsurface while a digital elevation model (DEM) and hyperspectral imagery record surface conditions. Integration of the two data sets can reduce ambiguity when interpreting mine tailing distributions and their subsequent alterations.

Jan 1, 2001

By Cameron J. Clayton

Cumberland Resources Ltd. is currently planning to develop the Meadowbank Gold Project located some 70 km north of Baker Lake, Nunavut in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of up to 6 main gold bearing deposits within relatively close proximity to one another which are planned to be mined primarily as a truck-and-shovel open pit operation and using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of 8 to 10 years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11 °C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site, and the physical environment, pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project.

May 1, 2004

By J. K. Afidenyo, J. Osei-Owusu

"The Obuasi Mine of AngloGold Ashanti Limited has been operating the world’s largest Biooxidation Plant at its Sulfide Treatment Plant (STP) in Ghana, using the Gencor Biox® technology since February 1994. The Biox® technology was preferred to other alternative methods of treating refractory sulfide ores such as roasting, pressure oxidation and nitric acid leaching due to among other reasons, its lower capital and operating costs, reduced technical risk, relatively benign environmental impact and its ease of operation and maintenance in a remote location.STP has since commissioning succeeded in operating this technology successfully but not without some operational problems. The Plant has seen a number of upgrades and modifications in its circuits which were motivated by cost, operational and throughput constraints.The objective of this paper is therefore to highlight the mine’s experience in the treatment of its complex carbonaceous refractory sulfide gold ores with emphasis on plant operations and improvements such as the Biox® reactors expansion, flotation concentrate upgrade project and neutralization circuit modifications. The Biox® Plant operating cost is also discussed.INTRODUCTIONThe Obuasi mine forms part of the AngloGold Ashanti Group of Gold Mines. It is located in the Adansi West District of the Republic of Ghana. The mine is primarily an underground operation, although some surface mining still takes place. Ore is processed by two main treatment plants: the Sulfide Treatment Plant (for underground ore) and the Tailings plant (for tailings reclamation operations). A third plant, the Oxide Plant, is used to batch-treat remnant opencast ore and stockpiles, of which there are adequate tonnages to keep the plant operational until 2008.Though reference is made in this paper to the Tailings and Oxide Treatment Plants, the main focus will be on the Sulfide Treatment Plant."

Jan 1, 2008

By Anton Gronningsater

AS we know, Sir Henry Bessemer introduced Bessemer converting in the steel industry about 1855. It was not until twenty years later that the principles were adopted by non-ferrous metallurgists. In 1880, Manés first produced blister copper from matte in a converter, a very important forward step in copper metallurgy. For thirty years, up to about 1910, bessemerizing of copper matte was carried out in the acid-lined converter. It is not necessary here to enumerate all the shortcomings of that operation, one of which was that it strictly limited the grade of matte that could be treated; a 35 per cent matte was low in those days. From the early days of copper converting, many and repeated attempts were made to use a basic converter lining, and the older metallurgists will remember the numerous reports and discussions in connection with such experiments. These make interesting reading. I quote from a book published in 1900: ?'The siliceous lining is as much a part of the process of copper converting as magnesia lining is in the basic bessemer treatment of phosphoric iron, and it is suicidal to attempt any other kind of lining, either water-jacketed or basic.' "Even if the silica could be introduced in this way (through the tuyeres), it would still produce another trouble in the converter. The small particles of silica, being cold, would combine very imperfectly with the iron oxide and produce granulated and pasty slags, which could not be skimmed or poured out of the vessel".

Jan 1, 1942

By L. R. Plitt, A. A. Turak, B. C. Flintoff

"Since the publication of empirical cyclone models by Lynch and Rao in 1975 and by Plitt in 1976, the technical literature on this subject has consisted primarily of reports of applications, with only a few articles discussing basic modifications or enhancements in model form. In fact, most of the modelling eff ort in this period has been concerned with theoretical models based on the hydrodynamics of multiphase flow. (Preliminary resutls have been encouraging, however, it will be some time before this approach reaches the practical application stage.) This paper presents a review of empirical cyclone modelling technology, with an emphasis on developments since the mid 1970s. The topics addressed include homogeneous and heterogeneous ores, parameter estimation techniques, parameter confidence intervals, and the introduction of a new conceptual model of cyclone operation.IntroductionSince their first reported application in the mineral industry by Driessen (1939), cyclones have become a common unit operation in all of the process industries. The widespread use of the cyclone stems from its relative low cost and its versatility. It can be employed to carry out liquid-liquid, solid-liquid and solid-solid separations. It is the area of solid-solid separation which is of greatest interest to a mineral processing engineer. Historically, this area was divided into two application categories: (I) Separation according to density, the cyclone washer, and, (2) Classification according to particle size, the cyclone ciassifier. (When water is the carrier fluid, the cyclone is more often called the hydrocyclone. For the purposes of this paper the two names are used interchangeably). Classification is the principal application in mineral processing circuit s. Within this category, the cyclone is most commonly employed to provide some positive control over the size distribution of product from a grinding circuit. Other uses include sand-slime separation prior to froth flotation and mill tailings treatment, either for dam construction or in backfill preparation."

Jan 1, 1987

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

By Brad Sampson

Project Ownership ?Discovery Metals Limited ?ASX (DML), BSX (DML), AIM (DME) ?Market Cap AUD 195M ?Key assets ?Boseto Cu ?Dikoloti Ni The Boseto Copper Project ?Location ?Setting ?History ?Status ?Future

May 1, 2010

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

Reliable estimation of in situ stress is a major step in the analysis and design of underground excavations in rock, particularly for evaluating the stability of underground structures to prevent failure or collapse. In the last ten years, the Western Australian School of Mines (WASM) has studied and developed an AE stress measurement technique using orientated core named the WASM AE method. It allows the determination of a representative and detailed knowledge of the in situ stress field during the early stages of a project (such as mine feasibility studies), even in areas where development access is not yet available. The method has been used for in situ stress measurement at more than 80 mine sites worldwide with over 200 individual stress measurements carried out to date. This paper describes the sample collection, sample testing and reconciliation of results for very deep measurements carried out at the Craig-Onaping mine complex in Sudbury Canada. The results constitute the deepest measurements undertaken to date at the WA School of Mines and indicate that the main principal stress is horizontal and oriented parallel to a common regional sub trend in a NE/SW direction.

May 1, 2009