Search Documents

By James D. Noll, M. Eileen Birch

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rule making for coalmines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Sub micrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the sub micrometer dust is organic and mineral matter, sub micrometer EC concentrations would be much lower than sub micrometer mass concentrations. Laboratory and ?eld results reported here in indicate the amount of EC contributed by sub micrometer coal dust is minor. In a laboratory test, a sub micrometer EC concentration of 31µg m 3 was found when sampling are spirable coal dust concentration over three times the US compliance limit (2mg m3). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18µg m 3 when size-selective samplers were used to collect dust fraction shaving particle diameters below 1.5µm sub micrometer EC concentrations were ?7µg m3. In dieselized mines, sub micrometer EC concentrations are much higher.

By Leonard Obert

This report presents evidence indicating that when rock is stress-relieved during the course of mining or in drilling a core, it may be altered or damaged to the extent that the physical properties of the relieved specimen are not the same as those of the in situ rock. Furthermore, this type of damage may result from stress change other than that accompanying stress relief, such as the application of a relatively large compressive stress. In some instances the damage is microscopic, manifesting itself as incipient cracks or the failure of individual crystal bonds. However, if the sample is taken from a high-stress area, macroscopic damage may occur.

Jan 1, 1962

By Rudolf E. Greuer

This study concerns itself with two topics of the mine ventilation - mine fire interface which, when the work for this study began, did not seem to receive sufficient attention. Section 1: Comments on Spontaneous Combustion of Coal in Mines It is attempted to describe heat generation, heat and oxygen transport, in such a way that existing experimental data for U.S. coals can be used to assess conditions inducive to spontaneous heatings quantitatively. Investigated are, in particular, critical air velocities, minimum sizes of coal accumulations, moisture contents and the influence of mining factors. An extensive, practice oriented literature survey is included. Section 2: The Early Detection of Mine Fires by Assessment. of Mine Gases The suitability of the major constituents of combustion products for an early detection of fires is discussed. The same is done for gas concentration ratios. Since it was felt (at least at the time when this report section was written) that the value of the carbon monoxide/oxygen deficiency ratio was overestimated, the usefulness of monitoring this ratio as compared to monitoring CO concentrations was critically investigated. The state of art concerning instrumentation and organization of fire detection systems is reviewed also.

Jan 1, 2011

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By A. J. Farstad

Recent advances in microcomputer technology have opened the way for systems which can track the location of underground mining personnel from the surface. A computerized system has been designed which is capable of not only tracking the location of the miner but also of monitoring underground parameters, communicating between work stations and sounding alarms when underground conditions are judged to be unsafe. For the system described herein, the locations of the underground personnel are detected by a network of underground terminals which routinely emit RF pulses to interrogate miniature transponders worn by the miners. Each transponder is uniquely programmed to delay its response in such a way that the RF terminal can identify the individual transponders by the time slots in which the responding pulses are received. The underground terminals are then interrogated by the host computer on the surface which keeps a running account on underground mine conditions and personnel. The underground portion of the system is designed to operate even during mine emergencies, deriving its power from rechargeable battery supplies which are float charged during normal operation. Nine mines were visited on this program and the industry reaction to the system was generally favorable. By slanting the system design for daily use in the mine, the chance of its acceptance by the industry is enhanced. Furthermore its likelihood of being operational in the event of an emergency is significantly increased.

Jan 1, 1981

By Paul C. Hyndman

Three properties in the Tuolumne River RARE II area, the Eagle Bluff Mine (lode) and the Indian Creek Bar and Bossy Bar Prospects (placer), have identified subeconomic gold resources (table 1). Nineteen other properties have potential for gold resources. Adjacent to the study area, five properties have identified mineral resources, and nine others have potential for resources. Properties having high-grade zones (shoots), but licking enough tonnage to be classified as resources, are listed in table 2. Gold, in lode and placer deposits, is the principal mineral commodity in the Toluene River study area. Ten properties within the RARE II boundary have gold-rich zones or shoots; they range in size from 12 to 2,500 tons and in average grade from 0.09 to 0.97 oz gold per ton.

Jan 1, 1983

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the “bigger-the-better” design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

By Robert A. Cummings

A rock mass classification system has been developed for support estimation in mines using caving methods. The developed system (MBR System) accepts readily-obtainable geotechnical properties, and mining geometry, to develop a rating that permits recommendations for drift support in block caving mines. The data base includes major active United States caving mines. The method is intended to be used for planning and estimating purposes and for preliminary support design. The Manual explains the organization and nature of the MBR System, its derivations, details of required input data, methods for assessing the data and for developing rock mass ratings, and techniques for selecting the most appropriate mine support recognizing mine requirements and desired stability. A worked example is provided.

Jan 1, 1984

By William H. Holley

Thirteen additional preservative/fire retardant systems were applied to Ponderosa pine and evaluated for flammability both before and after water leaching. The more promising four systems were given a thorough evaluation for flame spread, toxic gas and smoke density levels, resistance to decay, and compressive strength. The most promising system on the basis of history of usage in the mine, ease of application and low cost as well as overall performance is the Fyreprufe/ACC Albi 107A/ 144 combination. A survey of inspection tools and instruments, identified equipment which could be assembled into an inspection kit for use in determining the extent of decay and/ or impregnant retention levels in mine timber. A literature search identified those high fire hazard areas found in a typical mine. Timber and other wooden structures used in such areas should be treated with an acceptable fire retardant system. A survey of insurance companies revealed that the use of such treated timber in the mines would probably have little or no impact on the rate structure.

Jan 1, 1980

By J. Douglas Causey

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 12,740-acre Blue Canyon Wilderness Study Area (OR-003-073) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 27 miles northwest of Jordan Valley. The study area is underlain by Tertiary welded tuff, tuff, perlite and tuffaceous sedimentary rocks capped by basalt. Jasper has been mined from several localities. Some mining has been done by hobbyists. However, the area has been covered by mining claims since 1964, with mining done by commercial operators. This region has been a source of "Owyhee picture" and other similar jaspers. More recent exploration has focused on the gold potential of nearby areas such as Quartz Mountain and Red Butte.

Jan 1, 1989

By R. Marshall

Electrical trailing cable handling techniques and practices used in metal and non-metal surface mines were investigated by obtaining information through actual visits to the mine properties located in a variety of geological areas and climatic conditions. An analysis was made of all accidents related to cable handling which are cataloged by HSAC* for the period from 1971, through June 1980. Information was also collected from mine operators concerning near accidents and non-reported accidents. The results of this investigation were presented to the U.S. Bureau of Mines in an effort to outline recommended practices for cable handling in surface mines and to recommend additions and/or changes in the present regulations now being enforced by MSHA** field inspectors. These recommendations are also intended to assist the U.S. Bureau of Mines in evaluating the need for assisting the mine operators in the areas of training and distribution of information related to material handling of trailing cable. * Health Safety Analysis Center ** Mine Safety & Health Administration

Jan 1, 1980

By W. C. Babcock

This report covers Phase V of .a continuing program to apply a new liquid membrane process called coupled transport to the recovery pf metals from hydrometallurgical leach solutions. During this phase of the program, a membrane system of moderate scale was constructed and field-tested at the Exxon Highlands Mine and Mill Co. site near Douglas, Wyoming. The test unit contained four hollow-fiber membrane modules, each with 100 ft2 of membrane area. In the field tests, about 1000 gallons per day of leach solution was processed. The unit was operated on the leach solution for about 50 days. Leach solution entering the unit contained 100 ppm uranium. This concentration was reduced to about 5 ppm by coupled-transport treatment, and the uranium was concentrated to about 2 wt% as a uranyl carbonate product. Under these conditions, a transmembrane uranium flux of about 2.5 lb/ft2-year was obtained. An economic analysis showed that the cost of recovering uranium from this leach solution via coupled trans-port is about $1.20/lb. At higher concentrations of uranium in the leach solution this cost is reduced. For example, at 1000 ppm the cost of uranium recovery is about $0.30/lb.

Jan 1, 1983

By Roger J. Morrell

Bureau of Mines laboratory experiments with reduced scale cutter and cutter forces were performed to (1) define the fundamental relationships governing disk cutter performance and (2) to develop a method of predicting disk cutter performance in soft, medium, and hard rocks. The rock cutting experiments were performed in four igneous and metamorphic rocks that ranged in compressive strength from 38,000 to 67,000 psi. A special testing machine called a linear cutter apparatus (LCA) was used to load and traverse a free rolling disk cutter across a smooth rock surface. Each pass of the disk produced a single crater, and runs were spaced to avoid breakage between craters. During each run the normal and tangential cutter forces were measured and recorded. The soft and medium rock data were obtained from previous Bureau experiments with disk cutters. Crater depth, tangential cutter force, crater volume, specific energy versus normal cutter force, and crater width versus depth are defined within this study. With the use of standard physical properties, performance prediction equations were developed using stepwise linear regression analysis techniques. A method of using these prediction equations to calculate the boring rate, the cutter spacing, and the torque and energy requirements of a full-scale boring machine was also developed.

Jan 1, 1974

By M. G. Zabetakis

This publication describes an investigation conducted by the Federal Bureau of Mines regarding the cause of an explosion of a dephlegmator or fractionating column at the Cities Service Oil Company Refinery, Ponca City, Okla., January 22, 1959. The column was that used with the refinery's No.1 Dubbs Coker. The explosion caused the death of an employee of the refinery and resulted in extensive damage to the refinery and to nearby property. The Bureau's study of the explosion began January 26.

Jan 1, 1960

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By Hugo E. Camargo

Noise Induced Hearing Loss is the most common occupational disease in the U.S. and of paramount importance in the mining industry. According to data for 2006 from the Mine Safety and Health Administration (MSHA), Continuous Miner operators accounted for 30.2% of underground mining equipment operators with noise doses exceeding the Permissible Exposure Limit (PEL). This figure becomes more significant considering that 49% of the 2006 national underground coal production was extracted using continuous mining methods. Thus, there is a clear need to reduce the sound radiated by Continuous Mining Machines. The first step towards efficient noise control of a Continuous Mining Machine requires identification of the various noise sources under controlled operating conditions. To this end, a 42-microphone phased array was used in conjunction with 4 reference microphones to sample the acoustic field of a machine in the Hemi-anechoic chamber of the Pittsburgh Research Laboratory. These data were processed using a frequency-domain beamforming algorithm to obtain acoustic maps of 5 sides of the machine. The focus of the test was on the conveyor noise since previous studies showed that operation of the conveyor is the most important contributor to the sound radiated by the machine. From the acoustic maps, the following potential areas for noise control were identified, and included: chain-tail-roller interaction, chain flight tip-side board interaction, and chain-upper deck interaction.

Jan 1, 2008

By J. G. Donaldson

Nickel containing less than 0.01 percent of total metallic impurities was produced at the Rolla Metallurgy Research Center of the Bureau of Mines by electrodeposition from purified electrolytes. The first report on this research4 described purification of electrolytes by selective precipitation and by liquid-liquid extraction. This second report describes a procedure: or electrodepositing high-purity nickel from electrolytes purified by passing a nickel ammine solution through a column of an ion exchange resin. The nickel electroplated directly from the ammine solution without further treatment; a titanium cathode and two platinum anodes were used. The nickel deposit was dense, smooth, and adherent, and contained less than 0.001 percent each of cobalt, copper, and iron, and spectrographically detectable traces of aluminum, magnesium, and silicon. Nonmetallic impurities in the nickel metal were carbon and sulfur, each present in concentrations of less than 0.01 percent. The results of several experiments planned to purify solid nickel salts by zone refining are also reported. These salts, after purification, were intended for use in preparing electrolytes for deposition of high-purity nickel. Results were not encouraging so that the more promising ion exchange procedure was emphasized chiefly.

Jan 1, 1962

By Roy F. Waters

An inventory was made by the Bureau of Mines of wastes of mineral origin, water requirements, treatment of wastes, and water treatment practice of 163 industrial installations in the Lower Missouri River Basin. This is the second and concluding report on the survey, conducted in cooperation with the Missouri Basin Field Committee of the Department of the Interior as part of the Missouri Basin project. Principal industries covered by this second report are: Sand and gravel, coal, meat, ice, brewing, paint, petroleum, chemical, fabricated metals, and a number of industries having either no waterborne wastes, or none of mineral origin. Gravel, sand, and silt from 47 producers are the major wastes, totaling 6 million tons annually, Coal mine wastes in the form of slurried solids from washing crude coal are second in volume, totaling 100,000 tons per year. They contain an average of about 40 percent coal. Salt is the third largest waste, amounting to 28,000 tons per year, Next is calcium carbonate, most of which is formed in water treatments, Because of its high unit value, chromic acid is important, although the waste quantity is much smaller; cyanide wastes are also significant because large quantities of sodium hydroxide and chlorine are consumed in their treatments prior to disposal. The various industries discharging wastes use 38 billion gallons of water annually; the recirculation rate is 109 billion gallons per year. The plants discharging no waterborne mineral wastes use 2 billion gallons of water per year and recirculate more than 1 billion gallons. Sand and gravel plants use 13.5 billion gallons; petroleum refineries use 10 billion gallons in direct use and recirculate 82 billion gallons per year.

Jan 1, 1962

The condition of the domestic mining industry is obviously affected by the cycles in general business conditions. This study, the results of which are presented in a series of 78 charts, attempts to examine the interrelationships between the general business indicators and the major statistical measures for the base-metals industries during the cycles in the United States economy following World War II. For these industries the cyclical problem is perhaps less acute than the secular-trend problem. However, short-run fluctuations in production and employment do have very important impacts upon the welfare of the regions which derive a significant portion of their income from base-metals mining and processing industries. Any information concerning the normal patterns of development as the industries enter into a cyclical recession will permit better forecasts and perhaps help promote measures to alleviate the distress that occurs. Also, a systematic study of the comparative movements among the statistical measures during a series of cycles can bring to the fore the economic causation involved, and perhaps, after intensive study, can lead to a better method of short-range forecasting for these industries. This study has not fully achieved these aims. However, observations which significantly aid the interpretation of the current monthly statistics on these commodities are made, and some very general conclusions are drawn. The charts are presented so the interested people can examine them and draw additional conclusions. The charts refer specifically to cyclical analysis. The technique of indexing each cycle to its turning point effectively subordinates the longer term trend movements of the data. Thus, certain general conclusions flowing from this study and from the continuing economic research of the Office of Chief Economist will aid the reader by clarifying the frame of reference within which the charts should be examined.

Jan 1, 1961