Search Documents

New developments in the pipe conveyor and belt are advanced to address the growth in the capacity, length and complexity of pipe conveyor systems. Improved belt construction can offer better stability during horizontal curves and resistance to twist. Low rolling resistance rubber compound can significantly lower the power consumption and belt tension, producing capital and operation cost savings. Dynamic analysis, when used to analyze the conveyor?s starting and stopping behavior, can improve the design and reliability of long overland pipe conveyor systems. For these three aspects, technical backgrounds and field installations as examples are discussed in this paper.

Jan 1, 2012

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By Mitchell L. Fong

The Bay Area Rapid Transit (BART) District will be extending BART service south along an 8.7-km (5.4-mile) -long corridor in the city of Fremont, California as part of the Warm Springs Extension (WSX). The WSX project will link the existing BART system to the future BART to San Jose extension. A segment of WSX is located in Fremont Central Park (referred to as the Fremont Central Park Subway Project). The Fremont Central Park Subway is considered the most complicated and geotechnically challenging portion of the project with an underground subway box being constructed near the active Hayward Fault which is capable of ground motions up to 0.75 g and is located in an aquifer which is used for water storage and supply. Soil-structure interaction analysis was used in the design of the subway box to resist deformations due to earthquake ground motions. A water-tight excavation support system has been designed to allow subway box construction while minimizing impacts to the aquifer.

By Joseph M. McCann

The Brightwater regional wastewater treatment facility, under construction in King County, WA, includes an extensive conveyance system that will feature deep, soft-ground tunnels and shafts. Excavation of the Ballinger Way Receiving Portal to 65.8 m (216 ft) below grade through challenging geology was accomplished by means of artificial ground freezing. This paper discusses freeze design development, system installation and monitoring, and the contractual and construction challenges that were overcome, including work sequencing and excavation means and methods, together with lessons learned.

By W. J. Nokleberg, B. A. Bouley, T. K. Bundtzen

Central Alaska contains a wide variety of pre-, syn-, and post -accretionary mineral deposits that are related to the growth and evolution of the north-west North American continental margin. Withinpre-accretionary terranes, the Devonian-Carboniferous, carbonate platform-hosted MVT zinc-lead deposits of the Kandik and Reef Ridge districts in central Alaska, and the Devonian-Mississippian volcanogenic massive sulfide (VMS) polymetallic deposits of the Bonnifield, and Delta mineral belts of eastern Interior Alaska have received the most exploration interest to date. Syn-accretionary rift related, mafic and ultramafic sill swarms and zoned plutons of the Kluane-Nikolai igneous belt are currently being explored for Ni-Cu-Co-PGE deposits. Syn-accretionary granitoid complexes in the PurcellMountains, Illinois Creek, and Sitylemenkat areas have been explored for uranium-REE-gold, and tin-silver mineralization respectivelyPost-accretionary granitoid intrusions and associated volcanic fields that range in age from mid-Cretaceous to early Tertiary contain significant gold-silver-polymetallic resources in the East Central Alaska, Hogatza, and Kuskokwim Mineral belts. Collectively the three main post-accretionary plutonic/volcanic belts of central Alaska are part of the Tintina Gold Province, where exploration since 1990has identified about 848 tonnes gold.

Jan 1, 2000

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988

By K. S. Mortensen

The softwall mining system is a novel, new method of mining mineral deposits in soft, shallow, nonrock ground conditions. This method can mine the ore layer without substantially disturbing the existing overburden. The softwall mining system consists of machinery that is hydraulically controlled and powered, that can be buried (or used on the surface) to extract the ore or mineral from a layered deposit. The method is essentially an application of the longwall mining concept, modified for loose overburden and ore conditions, combined with hydraulic mining.

Jan 1, 2003

By James F. Kvitkovich, George V. Weisdack

Longwall mining techniques were introduced into U.S. bituminous coal mining operations in the early 1960s. These techniques were gradually adopted by many mines during the 1970s. By 1983, considered to be the peak of the longwall mine census, there were 118 active longwall faces in 79 coal mines throughout the United States. Beginning in 1984, longwall faces began a decline in numbers that has continued to the present day (Fig. 1). The geographic distribution of longwall faces today is shown in Fig.2 according to region. A breakdown of recent longwall mine production by region is shown in Table 1. An approximate breakdown of present longwall face installations by product (metallurgical and steam) is shown in Table 2.

Jan 1, 2005

By Y. Boissonnas

INTRODUCTION, The transalpine rail routes in Switzerland are well over one hundred years old. As the established routes no longer meet the demands of the continually increasing volumes of rail traffic between north and south, two new routes through the Alps were planed. The old Gotthard rail line is in fact a mountain railway. The northern and the southern access ramps?with a maximum speed of 80 km/h and a maximum slope of 2.2%?reach the old Gotthard rail tunnel at an elevation of approximately 1,100 m above sea level. This is approximately 900 m higher than the city of Milan. In 1992, the Swiss electorate people voted with an overwhelming majority in favor of the project to build the new base routes through the Alps. The Swiss voted again in 1998 in favor of the financing proposal for the new infrastructure. Swiss Federal Railways together with the BLS Lötschbergbahn were commissioned for the realization and management of the Gotthard and Lötschberg routes. AlpTransit Gotthard Ltd., founded by Swiss Federal Railways, was given the task of managing the design and realization of the Gotthard route until the start of regular service. In the meantime the shorter Lötschberg Base Tunnel was open to traffic in 2007

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By T. Wang

A new generated NaNO3 ? NaNO2 ? KNO3 ternary thermal energy storage system which has low melting point as 124°C and high specific heat capacity was studied for the short and long?term thermal stability by using the Thermogravimetric Analyzer (TGA). Based on the actual working condition of molten salt in solar two, the simulated cyclic thermal stability measurement was also conducted. The ternary system demonstrates excellent short ? term thermal stability and thermal reliability after cyclic heating and cooling processes. However, in the long ? term as well as the simulated cyclic stability measurement, large amount of weight loss was observed. Moreover, the stepwise long ? term isothermal study reveals that below 440°C the weight change is minimal and this temperature is viewed as the upper limit temperature of thermal stability for this ternary system. To determine the lost phases at high temperature above the upper thermal stability limit, techniques such as XRD and SEM are used to compare the condition of the salt mixture before and after the long ? term thermal stability study. On the basis of the comparison, it can be concluded that the major weight loss was due to the decomposition of sodium nitrite.

Jan 1, 2012

Nuclear power currently produces about 20% of the electricity in the US, with 104 nuclear power plants located in 31 states. The commercial US nuclear industry contributes over $4 billion annually to US workers in salaries and wages. 25,000 new jobs need to be filled in the next 5 years. There are over 30 new power plants under consideration by US utilities. The operating reactors use uranium oxide fuel enriched to about 4% U235 and fission is the process used to generate heat to form steam to drive the turbine generators. Nuclear energy is an important element in the US generation portfolio and represents the largest producer of nearly emission-free electricity. Most, if not all, of the operating plants will secure an extended 20 years of operation or more. The last plant constructed was ordered in 1978. New smaller, modular reactors are under design to provide less expensive, expandable generation options.

Jan 1, 2011

By O. A. Bascur

The lack of integration of mining and metallurgical information with sufficient detail for analysis causes inefficient operation and hence sub-optimal energy and water use. It is difficult to analyze the performance of mining and metallurgical processes without an integrated view of mine transactions, stockpile inventories, process flows and assays. To take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. This paper presents an infrastructure with advanced tools that sift through available data, identify and eliminate gross errors, and transform the data into business information for continuous improvement and optimization. Collaboration is a key component of improving efficiency of energy and water use, and the evolution of Web technology enables collaboration and troubleshooting of plant information to more quickly act on issues to reduce wasteful operation. Keywords: Mine Concentrator Optimization, Real Time Performance Management, Data Unification, Integration of Operational and Business systems, Mass and Energy Balances, Real Time Web Services, Equipment Availability, Efficiency.

Jan 1, 2009

By Michael R. King

The application and use of steel fibre reinforced concrete in precast tunnel lining design is a growing trend due to its advantages in performance over plain concrete, and ease of manufacture compared to traditionally reinforced concrete. However, the design process and performance characteristics of the material are poorly served by current codes and standards. This paper provides some basic design guidance for segmental linings, and compares the material properties for the different material options. A typical example is considered to compare the possible results of lining arrangement and thicknesses for a plain, reinforced, and fibre reinforced design solution.

Jan 1, 2005

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002

By Kerry Gee, Gary Colgan, James Fricke

Introduction Elevated zinc concentrations are observed in groundwater within alluvium adjacent to Silver Creek east of Park City, Utah. The study area is located in a small valley one and one-half miles northeast of Park City, Utah in Summit County, Utah (Figure 1). Although surface water concentrations in Silver Creek are typically less than 1 mg/l, groundwater concentrations have been measured as high as 85 mg/l in a near neutral pH environment. The elevated zinc concentrations in groundwater result from several factors including: (1) dissolution of zinc from tailings exposed at the surface and within the alluvium, (2) oxidizing conditions created by surface/ground-water exchange, and (3) ideal geochemical conditions for the dissolution of zinc-containing minerals. These ideal conditions include readily soluble minerals, available anions for complexation, and lack of available surface adsorption sites.

Jan 1, 2005

By Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from high extraction mining in southern Illinois. The objectives of the monitoring program are to study the inter- action between the ground surface and a foundation during a subsidence event and to determine the capability of the tiltmeter to detect and monitor subsidence movements. Tiltmeter data were obtained on two foundations constructed near Sesser, IL. One of the 30-by 40- ft foundations was constructed with a typical poured concrete footing, the other with a rein- forced-concrete footing poured on top of pol yethylene sheeting placed over a compacted layer of sand. Soil-filled bins were placed on the perimeters of both foundations to simulate superstructure loads. Monitoring pins and tiltplates were installed on the corners and midpoints of the footing. Additional survey points were established on the five-acre site to track the mining advance. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tilt- meter to detect and follow the tilt of the foundations is demonstrated.

Jan 1, 1986

By Charles W. Axten

Since the mid-1970s, samples of airborne and waterborne fibrous particulates have been collected in the area of the Northshore Taconite Ore Processing Facility by the Minnesota Department of Health (MDH), the Minnesota Pollution Control Agency (PCA), and the University of Minnesota. Indirect sample preparation has consistently been used although other aspects of the sampling methods and sites have varied and analytical procedures were altered over time as more accurate and precise microscopy methods were developed (i.e., phase contrast optical microscopy, transmission electron microscopy, transmission electron microscopy with energy dispersive spectroscopy). In the mid-1970s, levels of airborne fibrous particulate in the Silver Bay area averaged from 0.00030 to 0.03 f/ml. This level was significantly greater than levels of similar particulates in the St. Paul, MN area, although two of the Silver Bay sampling sites, considered individually, did not indicate levels of fibrous particulate markedly different than that seen in St. Paul. More recent sampling data (i.e., 1990?2001) indicate mean concentration of airborne fibrous particulates (amphibole-like fibrous particulates) of 0.0020 f/ml with a range of values from 0.0001 to 0.0140 f/ml. Such levels are not significantly different from those seen in other non-urban environments in the US and Europe. Concentrations of fibrous particulates in water samples were higher in the mid-1970 when iron ore tailings were being deposited in Lake Superior, but since the tailings have been deposited on land waterborne levels of fibrous particulate in the Beaver River have remained relatively constant averaging in the range of 7.5 MFL. This level is only slightly in excess of the current EPA drinking water standard for fibrous particulates. Review and consideration of this data is important in determining the potential health risks associated with airborne and waterborne fibrous particulates in the areas of the Northshore Taconite Ore Processing Facility. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Asbestiform fibers; Fibrous particulates; Cleavage fragments; Phase contrast optical microscopy; Transmission electron microscopy

Jan 1, 2007

By A. Anani

The need to optimize surface mining operations has led to the use of discrete event simulation (DES) modeling of truck-shovel systems. Often, these models assume truck cycle times are independent and identically distributed (iid) random variables, although, with significant bunching on the haul routes, this may not be valid. The objective of this paper is to present a methodology to (i) account for truck bunching due to slow trucks; and (ii) test for cycle time dependence (i.e. whether truck cycle time data is iid or not). We built a DES model that accounts for bunching due to a slow truck(s) and used the cycle times as data for further analysis. We then tested for cycle time dependence using Pearson correlation coefficients. The results show significant correlation of truck cycle times for different number slow trucks, with variable speeds. Assuming iid in modeling results in over-estimation of productivity and the uncertainty surrounding it. The over-estimation of uncertainty is pronounced when the relative difference in truck speed increases. The confidence interval of the means of truck loads/shift decreases with increasing number of slow operators. This work extends the usefulness of DES in truck-shovel applications.

Feb 27, 2013

By Brad Murray

Evaluating the performance of a shielded tunnel boring machine (TBM) can be difficult because the ground cannot be observed directly and in relation to the TBM attitude within the excavation. It is difficult to determine whether performance problems are caused by ground loading, steering issues, fine muck packing against the shield, or migration of annular grout around the shield. The Arrowhead Tunnels Project in Southern California uses strain gauges on its shielded hard rock TBMs to detect shield strains early and correlate them with tunneling conditions, thereby increasing the chances that problems will be correctly diagnosed and addressed to optimize TBM performance. The frequent automatic measurement of shield strain has also been valuable by confirming whether remedial methods used to free the machine after stoppages are effective. This paper discusses the qualitative interpretation of characteristic strain patterns on the Arrowhead Tunnels TBM shields and discusses installation details and special considerations for setting up a strain measurement system.

Jan 1, 2008