Search Documents

It has been proven theoretically and experimentally that the use of 10 - 30 per cent DRI in blast furnace along with iron ore or sinter results in lower coke rate and higher productivity. However, to-date this remains unpractised on a regular basis mainly because of economic reasons. The DRI produced by several methods are expensive and difficult to store/handle in large quantities because of its reactive nature and thus DRI in blast furnace remains unacceptable.

Jan 1, 1999

By Y. V. Swamy, B. Bhoi, H. S. Ray

Low-grade manganese ores with low Mn/Fe ratios can he enriched through selective carbon reduction of iron oxide to magnetite followed by magnetic separation o f the magnetite. Thermogravimetric analysis (TGA) was used to assess the preferential isothermal reduction of pure M1702 and Fe2O3 using solid carbon. This was followed by reduction of a synthetic analogue of composition comparable to an actual low-grade ore (i.e., Sandur manganese ore, Sandur, India). The carbothermic reduction of the manganese ore converts the hematite and goethite minerals to magnetite (Fe3O4), with the magnetite then going into the magnetic, fraction. The resultant nonmagnetic ,fraction becomes depleted of iron with an enhanced manganese content. These results show that it is possible to reduce the iron from 22% to 5.85%, thus increasing the Mn/Fe ratio from 1.52 to 6.2 with a manganese recovery of about 50%. The recovery was, further improved by grinding the magnetic fraction to -75 µm.

Jan 1, 1999

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By K Akiro

Volcanogenic massive basemetal sulphide and gold mineralisation of predominantly low sulphidation style has been located within Lower Tertiary basaltic and felsic volcanic and sedimentary sequences at Ufuo, in the Left April River area, northwest Papua New Guinea. The four discrete massive sulphide bodies, which have been so far identified, occur within a 3 +5 km area situated within a north west trending structural corridor. The sulphide bodies are all localised on the margins of the corridor where the bounding major through going faults are transected by regional faults. Mineralisation is characterised by massive pyrite-bornite-sphalerite-barite-quartz-anhydrite deposition with later galena-tennantite-chalcopyrite. Minor phases include enargite, goldfieldite and bismuth sulfosalts. Jasperoidal silica lenses and bioturbated sediments are closely associated with the massive sulphides. Basemetal sulphide mineralisation is also closely associated with phyllic-style quartz-sericite- altered host rocks underlying the massive sulphide lenses. This mineralised phyllic alteration is localised to fractures, veins and breccias that cross-cut propylitic style alteration characterised by quartz, epidote, chlorite, adularia and zeolite. The mineralised system possesses several hydrothermal features consistent with a copper-rich submarine exhalative volcanic hosted massive sulphide (VHMS) system, ie discrete massive sulphide bodies with abundant barite, associated jasperoidal silica and bioturbated sediments. However, exploratory drilling of the alteration zone underlying each of the massive sulphide bodies has not identified a well-defined zoned alteration pipe that is characteristic of such systems. The alteration is also similar to that of a porphyry-related low sulphidation system in which phyllic alteration has overprinted a regional propylitic style assemblage. The presence of sporadic enargite (and ?tennantite/tetrahedrite) suggest there were intermittent pulses of acid fluids in the system probably derived from exsolved magmatic SO2 which flowed directly to the surface along reactivated faults. The occurrence of tellurium and bismuth minerals is also consistent with a magmatic contribution to the metalliferous hydrothermal fluids. It is proposed that the VHMS orebodies are the products of submarine exhalative deposition generated by a crystallising magma emplaced within crust of on-going tectonism. Ufuo mineralisation is similar to many VHMS deposits elsewhere in that it is unclear whether the metals are derived from the magma directly, or via seawater leaching of the wallrock. Additional studies such as oxygen isotope analysis may assist in resolving this issue. If the metals are shown to be of direct magmatic origin then there may be good prospects for discovering economic-grade porphyry-related mineralisation at depth below the massive sulphide deposits.

Jan 1, 1999

By Fogarty J. G H

Ausmelt Technology has a unique capability of removing the impurities, phosphorus and sulphur, from the feed materials to the process. Sulphur is removed to the gas phase almost completely because of the interactions of ore and coal in the reaction region at the top surface of the slag bath. Phosphorus is removed to the slag phase, with both basic and higher, controlled iron oxide levels in slag being achieved in the process. The significance of these features of the process relate to the production of pig iron with very low levels of these impurities for the further processing to steel, and to the treatment of high phosphorus and high sulphur raw materials. The marketability of pig iron and the raw materials are discussed in relation to this feature of Auslron.

Jan 1, 1999

By K. Pathak

Loaders and dump trucks are the most commonly used surface-mining equipment. Negligence of the safety-engineering aspects of dump trucks may result in serious accidents in a mine. A reduction in the risk of an accident due to the deployment of trucks can he achieved by engineering analysis, risks assessment, improved safety features, active safety devices, condition-based maintenance, in-built protection systems, etc. This paper presents some cases of accidents in Indian surface coal mines and advocates a systems approach to safety.

Jan 1, 1999

By J. Nielen van der Merwe

During the process of pillar extraction at the Welgedacht Colliery, an unexpected pillar collapse resulted in the entrapment of equipment. The area was visited soon after the event to evaluate the stability of the area for the purposes of extracting the equipment. It was found that the area had stabilised sufficiently to allow work without undue risk to the safety of workers. The equipment was reclaimed successfully. A subsequent investigation into the reasons for the collapse was conducted. It entailed detailed underground and surface subsidence observations and numerical modeling. It was found that none of the perceived negative factors that were present at the time could result in pillar loads that were sufficient to cause the collapse. It was concluded that the local pillar strengths were less than the nationally used value and that they were possibly further reduced by aging.

Jan 1, 1999

Direct reduced iron (DRI), produced by the reaction between iron ore and reducing gasses, is used as a source of low-residual iron, in addition to ferrous scrap and pig iron, in the production of steel mainly through the electric arc furnace (EAF) route of steelmaking. The main DRI technologies in use are those of Midrex and Hyl, but in recent years a myriad of newer processes emerged based on variations in feedstock, reducing agent and fuel sources. Since the beginning of the nineties, DRI has increasingly emerged as a cheaper, low-residual iron feedstock for EAFs, which have traditionally relied almost entirely on ferrous scrap feed. The main stimulus behind the interest in DRI has been the increasing popularity of the EAF and the ?mini-mill? set-up as the favoured steelmaking option compared to the traditional and much less flexible blast furnace/ basic oxygen converter. This, however, has been creating a problem with regard to availability of low-residual scrap, resulting in upward pressure on high quality scrap prices and leaving DRI, traditionally the ?expensive alternative?, as a much more competitive consideration. The second main determinant has been the increasing production efficiency of existing steel plants which, in the light of improvements such as continuous casting and near net shape casting, has been constraining the supply of low-residual domestic scrap, traditionally the prime source of EAF feed. The explosion of current and proposed DRI projects has been accentuating the mounting interest of global role-players in assuring the availability of reliable sources of low-residual iron units for the future, especially in cases where definitive competitive advantages exist with regard to proximity to primary sources of iron ore and fuel (gas or coal).

Jan 1, 1999

By W Valery, S Morrell

In the mining industry blasts are usually designed to fracture the in situ rock mass and prepare it for excavation and subsequent transport. The run of mine (ROM) fragmentation is considered good when it is fine enough and loose enough to ensure efficient digging and loading operations. Mining optimisation strategy is hence usually focussed on minimising total mining costs and maintaining these ROM fragmentation characteristics. Although this approach ensures an efficient mining operation it ignores the potential impact on crushing and grinding. Investigations by several researchers have shown that designing blasts to produce ROM fragmentation to optimise crushing and grinding performance enhances the overall efficiency and profitability (Eloranta, 1995; Kojovic et al, 1995; Bulow et al, 1998; Kanchibotla et al, 1998; Scott et al, 1998; Simkus and Dance, 1998). Field experimentation in this area is often found to be difficult because of high implementation costs and insufficient understanding about the effect of fragmentation at different stages in a comminution circuit. Modelling and simulation of blasting and comminution processes provide a more economic alternative to explore the impact of blast design changes on the down stream operations (Kanchibotla et al, 1998; Kojovic et al, 1998; Adam and Siddall, 1998; Bulow et al, 1998). However, the reliability of such simulations depends on:the ability of the models to reproduce the physical processes that take place; characterisation of rock mass in terms of its blastability and comminution characteristics; and in the case of blast modelling the ability to predict fines (-10 mm) has been found to be particularly important as this fraction has a significant effect on mill throughput.

Jan 1, 1999

By Susumu Uchiyama

This machine was manufactured for excavation of the Roppongi station of the Tokyo Metro Line 12. This machine can excavate both the platform and the rail track at the same time in locations where the traffic is congested and has following features: A multi-centered TBM of the size of 7.06(H) x 13.18(W) m The world first H&V TBM, with right and left machine parts articulated vertically and separately for position control A large erector for simultaneous erection of column and central segments of special shape to construct a highly reliable tunnel This paper reports the design concept, construction, and work record.

Jan 1, 1999

By Brian Micke, Mick Gavrilovic

The problem of rock hang-ups in underground mining operations has been a continuing one since the days of the “hang-up man”. This position commanded the highest pay of any underground worker in many historical Western U.S. underground bulk-mining operations, due to the occupational hazards of the job. Although underground mining techniques and especially work practices have changed greatly since then, the hang-up problem is a continuing one in many mines which use gravity flow of coarse rock in their transport systems or in those mines where stressed ground causes rock slabs to spa11 and bridge rock passes and stopes. In addition, with mechanized underground open-stoping mining methods now being used in many different types of ore deposits worldwide, this problem has again emerged as a very significant one in many of these highly mechanized operations. This is especially so where the remote operation of loaders is used for removing blasted rock from underground open stopes.

Jan 1, 1999

By A. H. Mokken

Failed attempts at amalgamation of a gold/osmiridium concentrate, recovered behind pebble mill liners during re-lining, led to the discovery that the gold particles were coated and that nitric acid only could remove the coatings. Following this treatment amalgamation was rapid and resulted in a complete recovery of the gold that otherwise would have been lost in plant residues. Investigations into the nature and formation of the coatings led to the realization that the coatings were impregnations of harder elements, associated with the gold during grinding and driven into the softer gold surface by high pressure, impact and attrition. It was further realized that this phenomenon could be part of gold ore milling, world-wide. With these thoughts in mind the question is asked whether concentration down to micron sizes prior to cyanidation, should not play a greater role in gold recovery.

Jan 1, 1999

By B. C. Lewis

Have technological advancements in underground coal mining driven people's skills to new highs or have the expanded skills of mining people driven the industry's technological advancements. Who knows? What we do know is that both our technology and our people have made meaningful and significant advancements. Overall, longwall systems continue to increase productivity and retreat faster. Globally, gate road development is the primary bottleneck in a longwall mine. The primary bottleneck in gate road development is roofbolting. Generally, roofbolting is the bottleneck in room and pillar operations as well. This paper will present an integrated manufacturer's (Joy Mining Machinery) vision of the future in comparison to current equipment performance. Particular emphasis will be placed on roofbolter technologies.

Jan 1, 1999

By Michael Cooper, Eric Konigsmann, A. Moerman

"A paste backfill plant and underground piping distribution system was commissioned at the Brunswick Mine in June, 1998. Concentrator tailings, composed mainly of pyrite and lesser amounts of silicate minerals with a P80 of 37um (45 YO-20 pm), are pumped to the backfill plant. The backfill plant uses conventional thickening and disc filtering to dewater the solids, which are then mixed with binder in twin screw mixers. The paste is discharged through a gob hopper and one of three boreholes by gravity. Approximately 65% of the concentrator tailings will be placed underground at full production. The remaining thickened tailings will be pumped to an existing impoundment area. Application of paste technology will completely replace the use of cemented rock fill in the mine by the end of 1998.The design capacity of the paste backfill plant is a total of 360 dmtph of cemented paste through two parallel production lines. The plant is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher ProVox Distributed Control System that is in communication with the property information highway. Video and audio signals from the underground system are carried to the surface plant via a leaky feeder communications/fiber optic system.The underground distribution system consists of a network of 200mm diameter boreholes and piping. There are approximately 3.5km of boreholes and 5.5km of piping in the system. To minimize pressures, the greatest piping length from any borehole is approximately 400m with all piping being open-ended. There are no valves in the entire paste distribution system.Construction of the plant, including installation of piping to and from the plant and preparation of the underground distribution system, was completed in less than one year from the time of management approval for the $M 22.3 project."

Jan 1, 1999

By B. Unver

Effective strata control is a prerequisite for maintaining an efficient mining operation. If the strata in the vicinity of an opening are not controlled effectively, it is impossible to perform a safe, efficient and economical operation. In this paper, the reasons and outcome of instability problems observed in roadways opened in clay and marl at the Bolu Colliery of Yeni Çeltek Establishment are investigated. Roadways under examination were located in a syncline causing high residual tectonic stresses. Factors affecting the instability have been studied thoroughly by examining geology and tectonics of the area, establishing convergence measuring stations to understand in situ behaviour of supports and laboratory tests to determine engineering properties of samples taken from nearby convergence measurement stations. As a conclusion, a new production strategy and a new support system are recommended to maintain stability.

Jan 1, 1999

By Yushiro Hirai

Saganoseki smelter & refinery had operated two flash smelting furnaces from 1973, attaining 330,000 mtpy of copper production in 1989. In 1996, however, it carried out a "integration of two flash furnaces". That is, it doubled the feeding capacity to one flash furnace to shut down another furnace while maintaining the same production. Single flash furnace operation has successfully started in March 1996 accomplishing a great reduction of the total production cost. The production had reached to 350,000 mtpy in 1997, and further increased to 450,000 mtpy by executing the expansion program with single flash furnace in 1998. This paper introduces results of the single flash furnace operation and describes about an outline of the expansion.

Jan 1, 1999

By Steve Kral

Globalization was the key word for the mining industry during the 1990s, just as productivity was the key word of the 1980s. And globalization will remain the key word as the industry enters the 21st century, according to speakers at the Colorado MPD Meeting held in Colorado Springs, CO in May. The meeting, put on by the Colorado Section SME Minerals Processing Division, drew about 120 people to the Broadmoor Hotel. “Operating Globally” was the theme of the 49th annual conference. Speakers addressed the reasons why mining companies have limited their spending in the United States and have moved into Third World and developing nations.

Jan 1, 1999

By R Blair

The Domain and Burnley Tunnels, which are major features of the Melbourne City Link Project, are MelbourneÆs first road tunnels. They are 1.6 km and 3.5 km in length respectively and are being constructed through a variety of ground conditions. Deeper sections of the tunnels have been driven through the Silurian mudstone which underlies Melbourne. Other shallower sections of the tunnels pass through a variety of ground conditions including silts, sands, clay and rock and have been constructed using both top-down and bottom-up cut and cover construction techniques. The Yarra River Crossing is a 140 m length of the Domain Tunnel which crosses under the Yarra River on a relatively shallow alignment. The crossing of the river using cut and cover techniques was identified in the early stages of design development as being one of the most challenging stages of the works on the Southern Link. The prevalence of varying geological conditions combined with the need for maintained traffic and stream flow conditions provided a demanding and often conflicting set of criteria for which there appeared to be no one clear solution. A team of designers, constructors, estimators and specialist contractors were involved in a concept evaluation and risk analysis study spanning a period of approximately 12 months. During this study, four concepts were considered as likely contenders. This paper provides a brief outline of the four concepts addressing their relative merits, disadvantages and risks followed by a detailed description of the adopted solution, namely top-down construction using secant pile walling (east bank) and bottom-up in situ construction (west bank).

Jan 1, 1999

By G. E. S. Valadao, J. D. Miller, C. L. Lin

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake poremicro structure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 m, length of 500 m and height of 4000 m. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: 1) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method,2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4)some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By R. Pickering

The purpose of this paper is to explore the application of technology to stoping systems. Technology, because for the past 100 years the South African narrow reef mining industry has battled to control working costs in a labour-intensive industry. Stoping systems, because it is the stoping method and methodology which is at the heart of the mining system. Introduce a more efficient stoping system and the mining system will look after itself. The technology applied to stoping over the past 100 years can be categorized as follows: ?The introduction of pneumatic rockdrills early this century, the cumbersome rig mounted units being replaced by smaller, lighter hand-held units which were then made easier to use with the addition of an air leg ?Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s ?Hydraulic props as a support method arrived in the1960s ?Some people argue that tungsten carbide inserts were equally important. There have been a number of attempts to introduce different technologies into stoping, the most recent being trackless equipment. Where the stoping layout suits the technology it has been successful. There have been too many instances where a technology has been installed because it is fashionable. At the end of the day the outcome from change in the stoping systems has to be safer and more profitable mining systems. It is the contention of the author that change is only likely to be effective if it is supported by the introduction and application of appropriate technology.

Jan 1, 1999