Search Documents

By W Barry Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire, Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1992

A review of ground control procedures in Western Australian underground mines is presented. Geotechnical input into initial mine design and methods of ground control is rare. As a result, the frequency of unexpected rockfalls is comparatively high, with over three quarters of the mines adopting non-specialist ground control designs experiencing unexpected falls-of-ground. In contrast, mines that provide some level of specialist input into initial ground control design experience decreased rockfall frequencies.

Jan 1, 1992

By Zeni J. T

Gold was mined from quartz bodies at Ballarat East from the 1850s until closure of the last mine in 1917. The average depth of mines was about 350 m.Ballarat Goldfields Limited (BGL) carried out diamond drilling from surface between 1985 and 1987 which proved the continuation of gold-quartz mineralisation beneath the old mines.During 1989 an underground development program was commenced to access the mineralisation for detailed exploration. The program included two simultaneous shaft developments. These were known as B2 shaft and Llanberris No.1 shaft.

Jan 1, 1992

As the theme of the conference is ære-discover Otago' from the minerals point of view, it is also timely. Of the eight million ounces of gold recorded produced from Otago, perhaps a quarter of this came from the goldfields of St Bathans, Vinegar Hill and Cambrians. The most notable among them was the Kildare Hill Mine, which is the so-called Blue Lake at St Bathans today. The bottom wash encountered in this mine contained the famous Kildare lead, which averaged 7 1/2 dwt to the dish, and is still one of the richest leads of alluvial gold known in the world. The richness of this lead, the best encountered in these gold fields, is otherwise stated to have yielded more than 42 ounces of gold to the cubic yard. It should be borne in mind that this equates to about $22 000 per cubic metre, in todayÆs values. I have been told by older residents of this district that in fact about 1 million ounces came out of the Kildare mine and associated workings. In todayÆs values, this would be about 530 million dollars worth of gold. The largest mines in the district were at Surface Hill, Kildare Hill, Nicholsons, Vinegar Hill, the Never Fail claim at Shepherds Flat nearby, and at Cambrians. It would appear that in almost every case, work stopped when the bottom wash progressed too deep down dip of the anticline hills on which it was initially found. The mining methods were sluicing and hydraulic elevating, and although the gold bearing ground did not stop, eventually it exceeded the ability of the mining methods then available years ago, to work it further. When it is realised that the previous mining has removed what is likely to be only a low percentage of the gold resources in these fields, a tantalising situation presents itself today in that mining technology now available will enable another cut to be taken off these fields. As in the past, I believe this will be million ounce plus and multi-million dollar scenarios, where the economic and social benefits will become widespread prizes.

Jan 1, 1992

The Clyde Power Project, and its Clutha Valley Development forerunner, has taken widespread investigations for various hydroelectric purposes both along the valley floors upstream from Alexandra and on the higher schist terrain. As part of this work the nature and extent of many of the alluvial deposits have been resolved and the ages established with varying precision. Gold values have been approximately appraised in some areas as an element of environmental assessment.

Jan 1, 1992

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992

By G. Folmo

Allis Mineral Systems' GRATE-CAR agglomeration/induration/reduction process is currently being operated to process ilmenite at Tinfos Titan & Iron KS in Tyssedal, Norway. In this process, balled ilmenite concentrate is fed to a traveling grate where pellets are dried and preheated, using fully oxidized kiln exhaust gas. Hot preheated, semi-indurated pellets are fed directly to a ported kiln where reduction of the ilmenite's iron oxide fraction occurs in the presence of lump coal. The reduced pellet sand coal char are discharged from the kiln to an indirect rotary drum cooler. Cooled pellets and char are screened and magnetically separated prior to their further processing in a downstream smelting operation. The pellets are melted and the titanium dioxide and iron are separated. Operation commenced in late 1986.

Jan 1, 1992

Lime and cement manufacturing has a proud history in Otago, with the earliest lime kilns appearing around 1849 at Caversham and Kaikorai in Dunedin . At Dunback or Makareao (to be precise) three well-type kilns were built by the government in 1899. In 1909 these kilns were leased to the then Milburn Lime and Cement Company. They erected a large brick Schmatolla kiln in 1909, elliptical in plan and fired by coal gas. The kiln operated up until 1944 before being left derelict. The quarry which supplied the kiln also supplied the Burnside Cement works from 1929 up until its closure in 1988. The quarry was shifted to the top of the hill in the 1950s.

Jan 1, 1992

By D. J. Maconochie

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modern houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various house designs.

Jan 1, 1992

By P D. Katsabanis

"This chapter describes the principles for the derivation of the equations for a detonation wave.. Theimportance of the equation of state for the detonation products is demonstrated and commonly used equations of state are discussed. Furthermore a brief introduction to the TIGER code is presented."

Jan 1, 1992

By Distin P. A

The extraction of platinum and rhodium from scrapped honeycomb autocatalyst into hydrochloric acid/aluminum chloride/nitric acid solutions is described. Results are given for the effects of leachant composition, temperature and catalyst pre-reduction using hydrogen. Data are also presented for the recovery, by hydrogen reduction, of platinum and rhodium dissolved in the leach solution. Parameters studied include solution composition and temperature, hydrogen pressure, and platinum seed addition.

Jan 1, 1992

By Jorma Miettunen, Reijo Kalapudas, Pertti Koivistoinen

A new method for measuring the mill filling was developed by Outokumpu’s Pyhäsalmi concentrator during 1989-90. The method utilizes the power draw oscillation which is caused by the mill lifters. Each lifter bar causes a peak in the power draw and thus a continuous oscillation results. In a fixed time scale, the oscillation peaks will shift as the lifter bare hit the mill charge sooner or later depending on the volumetric filling of the mill. Thus the measuring method is based on the phase shift of the power oscillation. So far the measurement is utilized for maximizing throughput of the primary mills at Pyhäsalmi and Enonkoski concentrators and at Harjavalta slag concentrator. The paper describes the new method and the results achieved.

Jan 1, 1992

By Ichinose M, Tsuru T, Gotoh K

Since 1980, the Department of Mining Engineering at Kyushu University, in co-operation with the Ikeshima Colliery, Matsushima Coal Mining Co. Ltd., has been conducting a research project into longwall gateroad designs applicable to deep and poor strata conditions. During this period, the economic environment has drastically changed the situation of the domestic coal mining industry. Conventionally, the retreat longwall method, with re-use of gateroad, has been employed as it achieves higher recovery. However, from the view point of production efficiency, this method is not suitable because it requires intensive work in side packing and roadway maintenance. Therefore an interpanel-pillar system, or a two-entry gateroad system, was adopted to identify the factors responsible for excessive vertical closure in longwall gateroads. Field measurements and non-linear finite element analyses were undertaken to confirm the performance of this system. Study results indicate that the stability of the gateroad employing the rib pillar system is comparable to that of the conventional system of re-using Gateroads.

Jan 1, 1992

By M. Kalin

"Ecological Engineering, a biotechnological approach to the decommissioning of base metal mining wastes, is being tested on two pits (Gloryholes) in Newfoundland, Canada. Pit #2 has an average pH of 3.5 and flows into Pit #1 where, through additional ground water contribution, the pH is circumneutral, ranging between 5.5 to 7.The AMD in Pit #2 originates from underground workings and exposed massive sulphide on the pit walls. The overflow from Pit #1 averages about 10 L/s with less than 0.2 mg/L of Cu and 40 mg/L of Zn.Ecological Engineering utilizes organic substrate as a source of carbon and nutrients for microbial populations which can generate alkalinity and reduce metals. In 1989, limnocorrals (enclosures of 4 m diameter and approx 3 m depth) were placed in both pits to test the most suitable organic amendment (peat and sawdust). Microbial alkalinitygeneration was evident 95 days after placement of the amendment on July 4, 1989. The pH had increased after 120 days from 3.5 to 4.5 and by day 480 the pH was 7 in limnocorrals in Pit #2. Zinc concentrations in the limnocorrals in Pit #2, dropped from an average of 35 mg/L to about 2 mg/L or less, by day 480.A scaled-up experiment has been under way since August 25, 1990, where 390 m3 are treated in pit #2 and 750 m3 in Pit #1. One hundred eighty days after placement of the amendment, zinc was reduced in the acid Pit #2 from 40 mg/L to 15 mg/L. Research is underway to determine those factors which limit microbial activity."

Jan 1, 1992

In reviewing recent developments in the process mineralogy of gold it is convenient to distinguish between visible (>0.1 pm) and invisible gold (1 - 2 pm in size in polished section; these can scan the surface of a polished section, identifying the gold minerals, recording co-ordinates of the grains for subsequent examination, and making measurements of areas and sizes of the grains. However, problems of sample reliresentivity in polished section mean that such data may not give good quantification of gold mineral proportions and liberation/locking characteristics and other methods are required for this (amalgamation, cyanidation, ultra-fine milling and cyanidation). Characterisation of invisible gold in bulk material (eg a sulphide concentrate) can be done by mineral separation, ultra-fine milling and cyanidation or by quantitative point analyses of a large number of mineral grains. Analytical methods include electron microprobe analysis (detection limit normally -200 ppm but -10 ppm by using special techniques), ion microprobe analysis (secondary ion mass spectrometry - SIMS; detection limit -0.2 ppm) or proton microprobe analysis (PIXE; detection limit

Jan 1, 1992

By Don Kay

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By George McIvor, Bill Thompson, Don Whitmore, Brad Rhude

"In 1972 Manitoba Hydro decided to develop the hydro electric potential of the Nelson River. This program included the construction of the Jenpeg Generating Station at the point where the channel of the Nelson River discharged into Cross Lake. The Jenpeg station serves two primary functions: 1) Provides a control structure for the regulation of Lake Winnipeg.2) Acts as a 126,000 kilowatt hydraulic generating station."

Jan 1, 1992

By Michael S. Wieland

This report focuses on the U.S. Bureau of Mines research regarding desensitization and malfunction of delay detonators and cap-sensitive explosives. Delay blasting in underground coal generates tremendous shock waves and rifting forces that fracture and heave coal. The shock waves from charge explosions radiate outward in all directions through the coal, impacting neighboring charges with later delays. The impact phenomena have debilitating effects, causing degrees of reduced charge performance ranging from misfires or weak detonations to out-of-sequence detonations. Impaired charges react poorly, fracture less coal, and produce fumes with higher toxicity. Coal-mine, underwater, and simulator tests were conducted to more thoroughly understand the shock damage mechanism. Recently the U.S. Bureau of Mines partially resolved the malfunction problem by demonstrating the feasibility of formulating a rugged explosive. This rugged cap-sensitive candidate passed the requisite tests for certifying an underground coal-mine explosive. With natural aging the formulation rapidly lost initiation sensitivity. The charge formulation had to be rebatched to finish the testing and therefore could not be certified.

Jan 1, 1992

By Patrice Favreau

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commerical computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1992

By David P. Reddick

Economics is a social science dealing with the allocation of scarce resources. In modern times the “science” was identified by Adam Smith in his book, The Wealth of Nations, written in 1776. Mr.Smith, highly influenced by the Mercantilists of the 17th and 18th centuries, identified the “Invisible Hand” which would lead every individual to pursue selfish rewards in purchasing goods. He speculated these selfish motives would result in the best good for all. Price would be determined by barter, at a point where self-centered customers and vendors were mutually satisfied. Today, Smith’s theory is known throughout the world as “Capitalism” but most often termed “Free Enterprise” in the United States.

Jan 1, 1992