Search Documents

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

In 1980 Pancontinental Mining Limited decided that while the Jabiluka uranium project was still a major focus of the company's efforts some diversification was necessary. At this time it was decided to include precious metals in Pancon's exploration and acquisition objectives. As a result the now Paddington Gold tenements were acquired, explored and developed. Today, it rates as the 6th largest gold mine in Australia and at an expanded throughput of 1.2 million tonnes per year of ore it will produce about 110,000 ozs of gold per year. Following extensive exploration activities by Pancon's Exploration Division the Operations Division continued with development drilling finally proving up a reserve of about 8.4 million tonnes at an average grade of 3.2 g/t. An in- house preliminary feasibility study was followed by a two phase feasibility study by Davy McKee. This resulted in a recommendation to the Pancon Board of Directors to develop Paddington with an annual throughput capacity of 875,000 tonnes. This paper describes the acquisition, exploration and development of the Paddington project. It goes on to

Jan 1, 1986

By Donald O. Capstick

A mineral survey of a 5,700-acre portion of the 11,510-acre Upper Deep Creek Wilderness Study Area (ID-111-44B) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1985. No mining claims have been located, no minerals have been produced, and no resources have been identified in the study area. Three reconnaissance samples of alluvium from the Deep Creek drainage contained $0.21, $0.22, and $2.72 per cubic yard in placer gold, higher than usual for the Owyhee River canyonland area. The samples of near-surface material contained very fine gold in values too low to support large-volume commercial placer operations, but the quantity and size of the particles of gold in the alluvium is expected to increase near bedrock. Consequently, the area may be a target for recreational as well as small commercial suction dredge operations. The physical characteristics of the individual pieces of gold (bright and angular) indicate that it may have recently come from an unidentified nearby source.

Jan 1, 1986

By D James

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Limited has carried out an ore evaluation of one of New Zealand's largest known deposits of ilmenite located at Barrytown on the West Coast of the South Island, New Zealand. The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilising spiral, wet magnet, high tension and plate electrostatic separators have been designed to produce ilmenite from the ore. Studies to utilise the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

By J. J. Gusek, J. T. Gormley, V. Scovazzo

Glenrock, WY is underlain by two abondoned coal mines. Subsidence events have been recorded over the years, with the frequency increasing in recent years. As part of Wyoming's Abondoned Wins Lands Program, investigations including mining history/methods/mappings, subsurface drilling and material site searches were performed. Portions of the mines less than eighty feet from the surface, were identified as probable for subsidence. Subsidence control by hydraulic backfill was selected. Design included search and injection boreholes, water supply from the mines and the slurry mixing, transport and injection system. Injection system performance and backfill success is king monitored during construction.

Jan 1, 1986

Various software packages are discussed. These are components of an Integrated Planning and Scheduling System developed by MVM with the aim of providing up-to-date information for the Whaleback operation on: 1. Mine Topography. 2. Status of equipment in the mine. 3. Material moved from and within the mine. 4. Volume and density of same. 5. Quality of same.

Jan 1, 1986

By W. K. Callaway

The need to increase ore recovery and pillar stability caused the Magmont Mine staff to investigate the use of sandfill to accomplish both tasks. The use of hydraulically stowed classified mill tailings as a subsidence preventative will be discussed as well as the use of sandfill in pillar recovery and as a part of the regular mining cycle.

Jan 1, 1986

By Favreau RF

Over the last 20 years the blasting industry has progressed from the stage of being artform to a science as it is today. The use of computers to simulate blasting results has allowed blasting engineers to accurately pre- dict blast results and to optimise their blasting. This paper describes the computer blast simulator called BLASPA and its various applications in blasting. BLASPA allows the blasting engineer to predict blast results given known details of explosive properties, their distribution, rock type and properties, hole size, burden, spacing, collar and subdrill. The simulator runs mathematical situations and outputs numerical estimates of fragmentation and muckpile results. The paper discusses results which show that the mathematical outputs correlate very closely with actual results seen in the field, thus confirming the validity of the simulator. BLASPA can be used to help improve blast design by predicting stress levels in the rock mass and consequent rock breakage.

Jan 1, 1986

By Miklos D. G. Salamon

The laminated model, in conjunction with the seam element method, is expected to be a powerful predictor of subsidence due to coal mining. The fundamental solutions for the model are presented. Numerical approach to determine the roof-to-floor convergence and evaluation of ground movement are discussed. Numerical results and comparisons with field observations are given to illustrate the validity and the potential of the model.

Jan 1, 1986

By Zygmunt Sadowski

Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of chemical additives and metal ions present either added or present as contaminants, on the flotation. Fuerstenau and Palmer (1976) have studied in detail the adsorption of multivalent cations onto oxide and silicate minerals. It was observed that the adsorption of a multivalent metal species exhibits a sharp pH dependence which is related to the formation of hydroxy complexes of the metal ions in solution. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances cations such as Ca2+, Mg2+, Fe2+ and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions.

Jan 1, 1986

By Armstrong M

The Coal Mining Engineering Branch of the New South Wales (NSW) Department of Mineral Resources, in its continuing effort to improve coal recovery from underground coal mining operations, has undertaken a study of the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces. The strata movement was monitored by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were connected to the suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors started subsiding as soon as the face retreated past the borehole and continued to subside until the subsidence levelled off when the face retreated 900 m past the borehole. The zone of major caving and bed separation extended to roughly 10 to 13 times the extracted seam thickness and high tensile strains developed inthis zone. The bulking factor of broken strata was less than 1.14 which indicated that the roof layers collapsed in big blocks. The goaf compaction was almost complete when the face retreat was 200 m. Low tensile strains prevailed in the strata overlying the zone of caving and bed separation.

Jan 1, 1986

I am honoured and very pleased to have been given the opportunity this evening to say a few words of thanks not only on behalf of all the guests but especially for the delegates and accompanying persons attending the 13th Congress of the Council of Mining and Metallurgical Institutions. Firstly, I would like to congratulate Sir Hamilton Whyte,KCMG for his most interesting address. In his far ranging talk, when he showed knowledge of widely diverse subjects, I had a brief fear that he was going to be talking about the details of support methods in deep level mines, or how to avoid flotation problems in multi-metal mines. Although he did not go that far, he touched on subjects which have arisen this week - long term planning and secure supply of minerals at acceptable prices. The dire predictions of the Club of Rome have been debunked with a far more elastic supply of minerals having been proved. Combined with the importance of a falling birthrate in some parts of the world, this will lead to many changes in the future, when hopefully governments will take the long term view rather than look at the next budget or the next election. Maybe some of them are not too lazy to do this for all of us. However as a fellow Ukranian, I feel that he might have been called something different if he had been in Australia. Sir Hamilton, thank you for your talk. Once upon a time - and this is not a fairy story - there was a cobbler who had two sons; one very bright who became a professor of mathematics; the other, dim, who became a millionaire shoemaker. Asked for the secret of his success, the millionaire attributed it to a vital piece of economics which his father had imparted, "Be content with small margins on a large turnover." "So", said the millionaire, "I make my shoes for $2 a pair and sell them for $5. I am very happy with the three per cent profit."

Jan 1, 1986

Improve the safety of mine workers by developing a sensitive ground-fault relay system capable of detecting and isolating low level ground faults and thereby minimize the danger of electrocution. Approach Inadvertent, direct contact with energized conductors in underground coal mines is a major cause of electrocutions. Although relay systems designed to protect workers against such fatal accidents do exist in some industries, there are no effective ground-fault-sensing relay systems that address the special problems presented by power systems designed for U.S. mines. The Bureau of Mines conducted research to design and construct a sensitive ground-fault relay for use with low-voltage, alternating current (ac) mine electrical systems. Such a relay, sensing current leakage or faults in an electrical system, would send a trip signal to a circuit interrupting device which would then shut down power.

Jan 1, 1986

By Poi G, Madgwick J. C, Davis P, Pannowitz D, Cho D, MacKay B, Chan S. M, Varga R. A, Chun U

Periodic dilute sulphuric acid treatment ofstill, batch-fed, molassesenriched, microaerobic, manganese-dioxide-Ieaching microbial cultures led to marked improvements over untreated cultures. Percentage Mn++ recoveries increased (7X), rate of Mn++ formation improved (3X) and yields of Mn++ per molasses use were more economical (5 X). The yield in terms of molasses used improved with decreasing sugar used (eg 1.17 g Mn++/gram molasses at 0.2 per cent molasses (w/v) feed and 24 per cent (w/v) pulp density MnO2 tailings). The most effective Mn++ leaching in terms ofpercentage recovery (97 per cent) and rate ofleaching (46 mg Mn++/day) was at 0.5 per cent molasses (w/v) and 14 per cent pulp density (w/v) MnO2 tailings.

Jan 1, 1986

By R. H. Zeng

Many subsidence researchers in the U. S. have developed new empirical function methods to predict subsidence, or attempted to validate some empirical functions developed by foreign researchers for use in the U. S. An attempt is made in this paper to develop a new empirical function to predict a surface subsidence basin due to longwall mining. In the U. S., the emphasis of empirical methods for the subsidence prediction over longwall panels has been in large part on determining the profile functions for the major cross-sections of a subsidence basin. In this approach, the surface monuments are usually laid out along the major cross-sections and thus, the subsidence profiles developed are restricted for subsidence prediction along the major cross-sections. However in practice many monuments or surface structures for which subsidence prediction for damage evaluation is required, are not laid out along the major cross-section of the basin. In such cases, it is difficult to get either the empirical profile function for the cross-sections where these structures are located or to predict their subsidence based on the profile function developed for the major cross-sections. Therefore, there exists a strong need to develop a subsidence basin function with a reasonable degree of accuracy, which can be determined or confirmed by the data of scattered monuments on a surface basin. The same subsidence basin function can also be used for prediction of subsidence for any arbitrary points over a longwall panel. In 1982, He (1) proposed the clastic theory, for which he developed the basic differential equations describing the movement and deformation of overburden due to underground mining, and performed the selection of best solution for the equations. He found that the Weibull dietribution is the optimal solution. The Weibull distribution has three parameters that vary to fit the subsidence profile so well that the profile function derived from it provides a high degree of accuracy in subeidence prediction. However the results

Jan 1, 1986

By Bof J, Lowe S

BHP's newest colliery on the Southern Coalfield Is Tower Colliery. It is situated near Wilton some 60 kms south west from Sydney. It commenced its operations in 1978 and since that time has experienced considerable roof problems. In its eight years of operations, production has been 936 687 tonnes to December 1985. To a certain extent this is a reflection of the ground control r,,b1cros present in the colliery. paper out Iines the signif mt g,, logical features that are known to exist in the colliery and their influence on roadway development. Faulting has hindered the mine's development and an igneous intrusion has had outhursting associated with it. The prevailing roof rock has also had an impact on the roadway conditions. The paper will look at intersection deformation in present workings. Extensometers have been installed in these areas and provide measurements to verify visual observations. The results show a significant increase in roof movement as the roadway is developed from a single heading, to a T-intersection and then Into a four-way intersection.

Jan 1, 1986

By Rodger C. Fry

Underground coal mining has been active within the East Mountain property since the mid 1950's. As a result, coal from two seams has been extracted within large areas allowing surface subsidence to occur. Monitoring of subsidence annually, began in 1981 using on the ground conventional monumentation, surveying and photogrammetric monitoring. The data collected has shown the time benefits of photogrammetry and the relationship between observed subsidence and the geometry of the mined out area below.

Jan 1, 1986

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By Kepplinger W

The KR Process is a joint development by VOEST-ALPINE, Austria and its subsidiary company KORF ENGINEERING, Germany. This new technology allows production of hot metal on the basis of non-coking coal. The KR Process is based on the idea of separating the process steps realized in the blast furnace (generation of reduction gas, reduction of iron oxide and melting of the reduced iron) and including coking of coal. These reactions are carried out in two reactors: - the melter gasifier, where non- coking coal is coked and gasified into a high quality reduction gas and hot prereduced iron is melted. - the reduction furnace, where iron oxide is reduced by the reduction gas generated in the melter gasifier and discharged in a hot state. In order to prove the process a pilot plant has been set up in Kehl/ Rhine in 1981 with a nominal capacity of 60.000 tpy.

Jan 1, 1986