Search Documents

This modern plant consists of a battery of 72 Otto Wilputte Compound Under-jet Ovens with extensive plant for the recovery by-products. The ovens produce 9000 tons of furnace coke per week together with some 17,000,000 cub. ft. of coke oven gas, which is used for heating purposes throughout the works and for heating the ovens.Coal is supplied from the, company's colliel'ies and is stored under a Coal Handling Bridge of 264 ft. span and 365 ft. overall, capable of handling 250 tons per hour. The coal storage space of 1600 ft. can. be extended to a maximum of 2800 ft.Preparation of the coal for coking involves fine grinding which is carried out as follows:-Coal is dumped from rail waggons on to a conveyer belt which delivers it to a 12 ft. x 22 ft. Bradford Breaker, with a capacity of 400 tons per hour. The coal, then approximately 4 in. in size, passes, to the mixing bins; and after careful blending is reduced in the,hammer mills to a fineness suitable for the ovens.The fire coal is elevated to the main storage bin over the battery for subsequent charging by electric larry car. The average cokingtime is 15 hrs. 36 mins. At the end of ,this period the doors, are removed and the coke pushed from the oven by a mm. The coke, is, then quenched with fresh, water and sent to the Blast Furnace in 50-ton Copper Waggons.The gas is exhausted from the ovens by Brown Boveri turbine, exhausters of 23,000. cub, ft, per min. capacity. Exhaust steam from these is used for various. purposes in the By-Product plant. After removing the last traces of tar by Electrostatic Precipitators', the gas is bubbled through sulphuric acid, the ammonia forming ammonium sulphate, which is subsequently washed, dried and bagged for sa,le as a fertilizer. The gas then goes to the Benzol Scrubber Towers, where benzol and other derivatives are recovered and later redistilled and purified. The cleaned gas is then piped to the main works for heating purposes, being used with tar to fire the steel furnaces, and also the soaking pits and reheating furnaces.BLAST FURNACES.The company is at present operating two Blast Furnaces of 800, and 1000 tons nominal daily capacity respectively. The latter was...

Jan 1, 1938

By R. Hipsley, D. Arbonies, P. Dobak

South Arturo is a “Carlin-type”, breccia-hosted, oxide gold deposit located at the north end of the Carlin Trend. The discovery hole was drilled in July 2005 from mine dumps 1,000 feet south of the Dee open pit. Discovery hole (BD-72) encountered a cumulative 245 feet @ 0.056 opt Au beneath 850 feet of post mineral Tertiary Carlin Formation. Oxidation extends to depths greater than 2,000 feet in the deposit area. The deposit is presently in definition drilling stage with approximately 190,000 feet of drilling completed to date. A resource estimate is in progress. This paper will focus on the discovery and descriptive characteristics of the mineralization.

Jan 1, 2007

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1936

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country's total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment.   Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry.   Equipment suppliers now offer maintenance services, production guarantees and flexible financing.  Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a 'package' approach to customer service.

Jan 1, 1997

By W. J. Kingwell

Where the equipment, technique and materials are available for the construction of large diameter rock socketted piles, this is frequently the most economical and environmentally acceptable method of supporting very large concentrated foundation loads in geoglogically appropriate areas. This paper outlines the current approaches in Australia to design and installation of large diameter rock socketted piles. The equipment and procedures described generally reflect those developed or used by Vibro-Pile (Aust.), a company which, while installing the usual range of driven and bored piles, specializes in the design and construction of large diameter rock socketted piles and possesses special expertise in drilling in high strength rock. A high capacity crane attached drill for large diameter drilling in rock is briefly described. Discussed in detail are the construction techniques employed and structural and geomechanical design methods adopted.

Jan 1, 1989

By Deon van Tonder, Chuck Edwards

"Solvent extraction is used in many acid leach uranium circuits to upgrade and purify the uranium bearing solution prior to final product precipitation. A number of strip options are available to recover the uranium from the loaded organic. This paper compares some of these options on the basis of typical capital and operating costs for both the solvent extraction circuit and downstream uranium processing, and also considers other related issues. The aim is to provide an objective comparative assessment of these options that could be used as a qualitative guide in process selection or improvement.INTRODUCTIONIn the 1950s the uranium industry was the first industry to adopt solvent extraction (SX). Since then, the flow sheets have advanced. Notable was the introduction of tertiary amine extractants by General Mills during the late 1950s and 1960s (Mackenzie, 1997; Mackenzie, 2005), which is still today considered ‘state of the art’ technology. Initially solvent extraction was done in combination with ion-exchange, such as in the Eluex flow sheet, followed later by the adoption of direct solvent extraction from pregnant leach solution (PLS). From a strip-precipitation perspective ammonia strip followed by ammonium diuranate precipitation was widely adopted as the norm in the uranium industry. More recently alternative strip systems have been receiving increasing attention due to the environmental, health and safety issues associated with ammonia and the resulting calcined uranium oxide product. This paper explores some of these alternative options in comparison with the ammonia route.It is important to acknowledge that each operation is unique, and therefore the information and philosophy outlined in this paper serve to provide a general guide that can be potentially applied and adapted to any site or project."

Jan 1, 2013

By P E. H Gregg, R B. Stewart

Reclamation field trials commenced in 1985, two years before the granting of the Mining Licence. The level of pasture production on varying soil depths (0 cm, 5 cm, 15 cm and 25 cm) overlying both tailings and oxidised waste overburden was assessed.   After seven years, the rate of increase of N, C, P and S, losses of Sand P and pH changes were investigated on the plots where grass seed was sown into bare tailings. It was determined that on these plots it would take approximately 24 years to reach the original carbon and nitrogen levels at the mine site. Further tailings trials have been initiated to investigate alternative land use options for the tailings dam. Growth increases of 73% occurred in native species growing directly in tailings, and growth increases of 78% occurred in tailings amended with compost over the first six months. Pasture trials on tailings with and without a compost amendment have also been initiated. Research has commenced to investigate the restoration options for acid producing pit slopes. The early field trials have been put into practice with the restoration of oxidised waste on the tailings embankment. This is progressive with approximately 16 ha restored to productive pasture at present. Yields compare well with those of the most versatile and productive soils types investigated in baseline studies of the area before the tailings dam was constructed.

Jan 1, 1995

By Mary Ann Bennett, Val Nichols, Colleen Proctor

"In 1997 when Royal Oak Mines Inc. went into receivership, the mineral processing technicians (mill operators) who had been working at Giant Mine in Yellowknife, Northwest Territories for most of their career walked out with no credentials to serve as testimony of their knowledge and skills.As a result of new diamond mining activity and the establishment of socio-economic agreements, mining industry representatives approached the Department of Education, Culture and Employment (ECE), Government of the Northwest Territories, in 1999. They requested support and direction to promote training and recognition for mineral processing technicians at BHP’s (BHP Diamonds Inc.) Ekati mine. ECE recommended the development of occupational standards and certification.This paper describes the development process and end products that resulted from this collaborative project between industry, government and education. In addition, industry representatives involved in the project share their views on the development process and the benefits of standards and certification.The conclusion invites industry members to support national occupational standards and certification with their associated benefits: standardized training in the workplace and institutions, proof of competence for hiring, recognition of prior learning, and a nationally and internationally recognized credential.INTRODUCTIONSwiftly changing labour market demands are nothing new in the North. The fur trade and mineral discoveries have brought employment to workers in a feast and famine cycle for decades. In the late 1990s, the Giant, Con, Lupin, Polaris and Nanasivik mines were nearing the end of productive runs. Many experienced workers found that without credentials, they had no proof of their abilities to offer prospective employers."

Jan 1, 2005

By Kot F. v. Unrug

The present combination of coal market prices and reserves, situated in the Central Appalachian Coal Field, is such that mining of smaller coal reserve blocks has become economically attractive. In above drainage deposits, and particularly under mountain ridges, overburden depth can be changing within a wide range. Mines operating in these deposits are usually developing mains along the center of the ridge, with panels projecting from the mains towards the outcrop. Due to changing topography, proximity of the outcrop, and related cover depth, the panels have various lengths. In this reported case study, a mine in Pike County, Kentucky, along the Kentucky ?West Virginia border, difficult ground conditions were encountered, during the development of the mains, under shallow cover, along a narrow mountain ridge. An area having unusual density of vertical joints was encountered. Mining operations were suspended because of roof stability concerns. The ground conditions were studied, analyzed, and control measures proposed to ensure safe passage through the difficult roof area of the mine. The advancement of the mains, through this area of challenging ground conditions, was successfully completed. In this paper, ground conditions are described, with an explanation of the geologic process contributing to their formation. It is interesting to note that similar locations were predicted by the authors, to be encountered in the same mine, based upon the experience gathered from studying conditions of the case described within this paper. When approaching the predicted locations, stability problems appeared to be even more challenging than those encountered previously. Due to changes in the coal market, mine management chose to move the affected mining section to another area of the mine having better coal quality. The advancement of the mains, through the difficult ground conditions, was temporarily postponed. Based upon the analysis of a probable kinematical mechanism of blocks in the mine roof, ground control measures were proposed. The actual application of these principles proved to be appropriate, ensuring safe passage through the difficult ground conditions encountered in the mine.

Jan 1, 2006

By Jodi Roberts, Curtis Deredin, Jean-Guy Paulin

"Since the establishment of the Six Sigma quality improvement program in 2001, several projects have been successfully carried out in the copper-lead, zinc, copper separation, lead upgrading and bulk flotation circuits in the Brunswick Concentrator.This paper provides an update on the process improvement initiatives that have taken place since 2004 using the Six Sigma methodology:•,The recirculation of warm water to the flotation circuit (to save on energy costs)•,Installation of a heat recovery tower to recuperate the heat lost from the zinc dryers•,Installation of an extra row of cleaner-scavenger cells for the copper-lead circuit for extra capacity, and a new reagent scheme for the copper separation circuit that have increased copper and lead recoveries.INTRODUCTIONThe Brunswick Mine Concentrator (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The concentrator utilizes selective flotation to produce zinc, lead, copper, and bulk lead/zinc concentrates. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.Figures 1, 2, and 3 illustrate the historical annual average metallurgical performance and process improvements achieved at Brunswick Mine for the zinc, lead and copper concentrate products. The objective is to continuously direct metallurgical performance towards increasing grades and recoveries while minimizing operating costs."

Jan 1, 2008

By M. R. Pickus, I. W. Pickus

ORDINARILY age-hardening is thought of as being associated with a limited solubility of one metal in another. Much less has been written about the type of age-hardening that attends the formation of superstructures. Solid solutions generally have a disordered or random arrangement of atoms; that is to say, in a unit cell, such as that of the face-centered cubic lattice, there is no distinction between atomic sites. Atoms of a given metal may occupy cube corners or face centers. Under certain conditions, however, some alloys develop what is known as an ordered structure. In this case, cube corners would be occupied by only one type of atom and face centers by another type, Associated with this ordering process are many interesting changes in physical and electrical properties. Moreover, in many instances the alloys become susceptible to age-hardening. From the evidence now to be described, it appears that age-hardening in 14-carat gold alloys is due to the formation of both a super-structure and a precipitate. Alloys of the metals gold, silver and copper were known in antiquity. The available knowledge regarding their constitution has been ably summarized and extended by Sterner-Rainer,1 Janecke,2 Carter,3 Wise,4 and Coleman.5 Despite the long familiarity with these alloys and the numerous investigations of their properties that have been made, there is still much that remains unexplained. It has been known for a long time that the hardness of these alloys is closely related to the rate of cooling, Similar changes have been observed in the binary gold-copper system,6 one alloy of which corresponding to the formula Cu3Au, has been the subject of a careful and competent report by the English investigators, Sykes and Evans.7 They have established the fact that the shift of atoms from the ordered to the disordered condition takes place in some critical temperature range. At temperatures above the critical range the structure is random, and at temperatures below it the structure is ordered. No difference between these two structures is revealed by the microscope. Both have a face-centered cubic lattice and complete solubility, so that there is no evidence to suggest that the changes in properties are associated with a phase change, The more slowly the alloy is cooled, the higher is the degree to which the ordering process proceeds and the more marked is the increase in hardness. As experimental data were accumulated on 14-carat gold alloys, several contradictions arose. Certain observations tended to confirm the existence of a superstructure, while other observations seemed to be inconsistent with such a transformation. PRESENT INVESTIGATION As a focal point about which to develop this subject, it is expedient to consider first

Jan 1, 1943

By Chelsea Woodward

The Spokane Research Laboratory of the National Institute for Occupational Safety and Health has demonstrated a prototype hydrogen-fueled mining vehicle as an alternative to diesel equipment in underground mines. Safety and control systems were added to allow a 70-kW rubber-tired hydrogen vehicle, originally developed by the U. S. Bureau of Mines and Hydrogen Consultants, Inc. (now Hydrogen Components, Inc., of Littleton, CO), to be tested. This work began in late 2000 and culminated with a Mine Safety and Health Administration fire safety review and field tests at the Stillwater Mine in Nye, MT, in 2004.

Jan 1, 2006

By B. St. Pierre

"The alchemists' symbol for antimony is a diamond with a dot in the centre. The latin name ''stibium'' gives this mineral its chemical symbol ""Sb"" and the name to the principal ore containing antimony. This is Stibnite, a sulphide of antimony, and the valuable mineral at the Consolidated Durham operations. Stibnite chemically pure contains 71.69% antimony metal.Antimony is used in many forms, as an alloy in the production of metal products and as chemical compounds of oxides and sulphides. In Biblical times, antimony was used as a medicine and as eyebrow makeup.Today, the largest single use of the metal is as a hardener and strengthener of lead, and corrosion inhibitor in storage batteries. New applications for antimony in its oxide form as fire retardants are broadening the overall demand especially in the chemical, plastic and fabric industries. Other users include the Military for such things as tracer bullets, shrapnel, smoke screens and flame throwers. An unusual property of the metal is that it contracts when heated which has made it a valuable alloying metal in the printing industry, for heat shields on re-entry vehicles used in the space programmes, and also for the manufacture of bearings."

Jan 1, 1977

By Mehdi Razavi

Scope of the Study The possibility and risk associated with mining two stopes at the same time The influence of Creighton Fault on the stability and dilution The effect of irregular shape of stope walls on overall stope stability and ore dilution The support requirements for proposed mining plan

Oct 1, 2010

By M. C. Mound, E. Gallestey, C. Colbert

Continuous operating performance and high profit is one of the major concerns in the mining industry. Information systems are expected to reinforce and enable conformance to these requirements. The companion efforts of business management and production information systems press for tighter integration to avoid over-laps, multiple instances of similar data, and expensive maintenance of databases. Implementation of advanced intelligent systems throughout a mine operation can reduce costs, optimize investment and create a shorter payback via conversion of the data accumulated by field and process devices into information, and subsequently, into decisions. However, in order to harness the potential power inherent in these intelligent devices, adequate and flexible modular knowledge-based solutions are required. Fortunately, there has been at least one such practical response to this challenge, namely the ABB IndustrialIT portfolio. With these tools in place, production efficiency is reached via integration of process, production, and quality information. Moreover, they permit immediate detection and remedial action to changes to process and boundary condition variables. Finally, using advanced optimization techniques supported by dedicated mathematical models, they allow for economic process optimization (process set points and coordination thereof, energy management, production planning, energy supply contract optimization, etc) of the plant as a whole.

Jan 1, 2004

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN'm). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003

By Robert Hopler

Some few years ago, when the cruiser “Brooklyn” was passing through the fairway to the southwest of the Battery, the ship being fully equipped with stores, etc., and therefore at her maximum draft, she grounded quite heavily upon some obstruction, and received injuries which necessitated her docking at the Brooklyn navy yard, where extensive repairs had to be made on her damaged bottom.

Jan 1, 2007

By H. Preßlinger, H. Hiebler, K. Klepp, W. Posch, M. Mayr

It was investigated in which form sulphur is bonded in ladle slags. For this purpose, the mineralogical phases of the ladle slags were qualitatively and quantitatively evaluated by means of a microprobe. This slag characterization allowed reconstructing the bonding of sulphur into the phases of the ladle slag. Moreover, the reaction process with regard to the ionic theory as well as the structural formula for the mechanism of sulphur bonding were discussed. The bonding of sulphur into calcium aluminate slags is determined by the sulphide ion content in the slag as well as by the ratio of (CaO)/(Al2O3). Calcium sulphide separates only if the slag contains a large number of sulphide ions. When Ca12Al14O33is separated, the sulphide ion is successively integrated into the lattice. The crystal lattice of Ca12Al14O33is characterized by an open, three-dimensional anionic network composed of aluminium-oxygen tetrahedrons linking the edges. In this network, large interstitial spaces are formed, which may be filled with calcium ions on the one hand and statistically with a free oxygen or sulphide ion on the other hand. Key Words: ladle slag, structure, phases, calcium sulphide, calcium aluminate, desulphurization

Jan 1, 2004

"Generation and removal of fines are considered in the context of the mill and classifier as a single-unit process in which grinding rates and mechanisms, mill residence time distribution, circulating load, and classifier performance all interact to effect the overall grinding circuit productivity. Required process design specifications are identified, and a computer assisted design procedure for application of hydrocyclones in closed circuit grinding is presented. INTRODUCTIONThe purpose of the grinding circuit is to carry out the size reduction necessary to suitably prepare material for the upgrading process(I) The desired product size specification being the d1st1nguishing criterion between the ""fines"" (smaller than desired product size) and the ""coarse"" fraction (larger than desired product size), the capability of the grinding circuit to perform its task effectively depends on the nature of two processes that are taking place;(a) size reduction of the coarse material, and,(b) removal of fines from the system."

Jan 1, 1984