Search Documents

By Robert Hopler

In accordance with the 57th section of the Explosives Act, 1875, the following report on the working of the Act during the year ending December 31, 1903, is submitted. There have been no modifications of the law during the year. No complaint is made of any falling off in the general condition of factories and magazines, and in one instance only during the year have legal proceedings been taken for any irregularity. The occupiers of factories and magazines have invariably shown perfect readiness to remedy any defects, and the managers have themselves in many instances introduced improvements tending towards greater safety. The number of deaths (5) from accidents by fire or explosion in the manufacture of explosives is below the average for the decade (6•4). Looking to the large number of persons employed in this trade, the number of deaths is not excessive and will compare favorably with the death-rate in other dangerous trades. Notwithstanding the large increase in the manufacture of explosives, the average number of deaths has greatly decreased since the passing of the Explosives Act, whereas the number of fatal accidents with explosives under conditions to which the Act does not apply appears to increase with the extension of trade.

Jan 1, 2006

By Edward A. Barrett, Roberta A. Calhoun

MORE THAN 30 MILLION EMPLOYEES each year are exposed to hazardous occupational noise, and approximately one-third of them develop permanent hearing loss (NSC, 2000). Possible explanations for the latter statistic include worker regard for noise as a mere nuisance rather than as an occupational safety and health hazard, and consequent neglect of established protective measures (e.g., hearing protection); lack of knowledge concerning noise; improper use of hearing protection; worker indifference; and inadequate training (Bauer & Babich, 2004). Many drill rigs generate high sound levels, which vary according to the type of machine, its location with respect to the physical surroundings, and the location of the sound measured around the rig. A NIOSH study measured noise output from several types of drill rigs during field investigations (Ingram & Matetic, 2003). Two types of data were recorded the actual noise generated by the drill rig at various positions around the rig and the noise to which the drill operator was exposed during the drilling cycle. For the latter, sound level measurements up to 120 dBA were recorded while hammering casing (metal on metal) in drilling a water well (Photo 1). Several types of administrative controls exist to address worker exposure to loud drill rig noise. Rotating duties to decrease exposure time and posting warning signs in high-noise work areas are two such controls. Another is the use of hearing protection. Worker use of hearing protection has been disappointing, however. One study by the University of Michigan found that construction workers used earplugs and earmuffs only between 36% and 61% of the time that they were necessary (Lusk & Kerr, 1998). In a 2001 study, OSHA reported a relatively low rate of 30.4% for use of earplugs among construction workers (Walker, 2001). Why are rates for hearing protection use so low? One explanation may be workers' lack of concern for noise in the workplace. They expect workplace noise to be a loud and in¬ evitable nuisance and, therefore, accept it as part of the job. As a result, they disregard proven measures that can protect their hearing. Other workers may use hearing protection, but do so improperly. They may misguidedly remain in high-noise areas for extended periods thinking they are protected when in fact they are not. Other reasons for low use and/or misuse of hearing protection include poor education, lack of awareness and inadequate training (Nash, 2003). To address the training issue, NIOSH developed two exercises from which drillers can learn about noise, hearing loss and hearing protection. The first is an invisible ink exercise, titled "Drill Rig Incident" (DRI) (Photo 2); the second is a 3-D slide reel training aid, "Wearing Hearing Protection Properly" (WHPP) (Photo 3). DRI is an instructor-

Application of Kriging in Approximations of Grained Materials Characteristics Distribution Functions

Sep 13, 2010

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

Core samples, which were collected by the author from the Busang prospect, East Kalimantan, reflect a progressive evolution of a large magmatic-related hydrothermal system that is comparable to that encountered in many similar systems elsewhere in the Pacific region. The initial, localized deposition of sheeted porphyry quartz-molybdenite veins took place at high temperatures and fluid salinities, and at relatively deep levels. This was followed by an extensive phase of phyllic (sericite-quartz-pyrite ¦ tourmaline-apatite) wallrock replacement and vein formation. Propylitic (epidote-chlorite-carbonate-quartz) alteration was formed marginal to the phyllic assemblages. These porphyry-related events were centred in the Southeast Zone, and are probably associated with the emplacement of a felsic intrusion at depth. This event contributed only trace gold to the system. The early stages of hydrothermal activity were followed by an episode of quartz (¦ adularia) û carbonate û base metal sulfide veining, which was accompanied by argillic (illitic-kaolin clay) wallrock alteration. This event was sulfide-rich in the Central Zone and carbonate-dominated in the Southeast Zone. Gold mineralisation was observed in Central Zone drillcore to be associated with both sulfide, as well as carbonate, deposition. A final stage of epithermal-style quartz ¦ stibnite û realgar veins are, in the Central Zone, locally gold-bearing. The latter two events are interpreted to be associated with the late-stage exsolution of metal-bearing brines from the felsic intrusion that formed the earlier porphyry quartz-molybdenite veins and widespread phyllic-propylitic alteration.

Jan 1, 2002

By Ta M. Li

How will phosphate producers in southeastern Idaho fare with growing governmental regulations and environmentalism of the late 1970's? With a similarity that is reminiscent of the battles between the coal industry and environmental-conservation groups earlier in the decade, Idaho's future growth and a nation's need for phosphate fertilizer products remain uncertain. The catalyst that brought the issue to the forefront was the preparation of an Environmental Impact Statement (EIS) addressing the development of phosphate resources in southeastern Idaho. Although the final EIS was published in August 1977, resolution of rational and orderly growth in this potentially vital region remains stifled as Secretary of the Interior Cecil Andrus virtually "sits" on it.

Jan 1, 1978

Jan 1, 1989

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

Flow Sheet Development of Three Geographically Distinct Chromium-Bearing Ores

Sep 13, 2010

In the interest of safety in mining, the Bureau of Mines recommends: 1. That cages or skips used for hoisting or lowering men in vertical and steeply inclined shafts shall be provided with safety catches designed to prevent falling of the cage or skip if the hoisting rope or other connections break; and 2. That cars used. for hoisting or lowering men with ropes in slopes shall be provided with arresting devices, other than ordinary brakes, that come into action if the hoisting rope or other connections break. In presenting this decision, it is recognized that the principal requirements for safety in hoisting operations are the use of hoisting ropes of ample size and strength to provide a factor of safety recognized as adequate by the best en engineering practice; their proper care, protection against undue wear and corrosion, and frequent inspection; and immediate removal of ropes from service when inspection or tests cast doubt upon their further safe serviceability.

Jan 1, 1938

Characterization of ore and waste-rock material using automated quantitative micro-mineralogical techniques (e.g., QEMSCAN® and MLA) has the potential to complement traditional acid-base accounting and humidity cell techniques when predicting acid generation and metal release. These characterization techniques, which most commonly are used for metallurgical, mineral-processing, and geometallurgical applications, can be broadly applied throughout the mine-life cycle to include numerous environmental applications. Critical insights into mineral liberation, mineral associations, particle size, particle texture, and mineralogical residence phase(s) of environmentally important elements can be used to anticipate potential environmental challenges. Resources spent on initial characterization result in lower uncertainties of potential environmental impacts and possible cost savings associated with remediation and closure. Examples illustrate mineralogical and textural characterization of fluvial tailings material from the upper Arkansas River in Colorado.

Feb 27, 2013

A simple and cost effective technique to increase fragmentation and burden velocities without making major modification to the overall blast design is with ALTERNATE VELOCITY LOADING OR BOOSTERING OF ANFO. The technique requires the placement of a cartridge or slug of explosive, having higher density and detonation velocity than ANFO, every few feet in an ANFO column. The greater the difference in density and detonation velocity of the Alternate Velocity Load to ANFO, the more pronounced are the results. Emulsions were selected as the Alternate Velocity test explosives because they detonate closer to ideal conditions than most other commercial explosives.

Jan 1, 1989

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020

By Sheridan J. Rodgers

Toxic fumes generated during shot firing under actual mining conditions were measured. Eight shots with Gelodyn-2X and seven shots with Tovex-100 4VT were monitored. Average CO values for Gelodyn-2X and Tovex-100 4VT were 0.20 ft3/lb and 0.09 ft3/lb, respectively. Average N0x values for Gelodyn-2X and Tovex-100 4VT were 0.049 ft3/lb and 0.026 ft3/lb, respectively. The results obtained with these in-mine tests will be used by the U.S. Bureau of Mines in the development of a large chamber method of measuring fumes from shotfiring of explosives.

Jan 1, 1977

By Manuel Gomez

Low-temperature carbonization product yields for 129 coals representative of 12 Utah coalfields were estimated, using regression equations developed from heating value and proximate and ultimate analysis data. It was shown that yields of char, tar plus light oil, water of decomposition, and gas, as well as the gas volume and the heating value of the gas, could be predicted with reasonable accuracy. Published and experimental results from eight Utah coals carbonized at selected temperatures in the 4500 to 1,000° C range were used to determine the effect of temperature on product yields. Carbonization temperature, heating value) oxygen, and volatile matter of coal appear to be the principal variables influencing carbonization product yields. Data presented show that the heating value and the residual volatile matter in low-temperature char may be predicted using relationships developed from proximate analysis data for 220 coals.

Jan 1, 1967

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By William Seymour, L. D. Schmidt

"FOREWORDAmong many problems created by World War II, the question of supplies and distribution of raw materials is of outstanding importance. One of the most critical of these raw materials is fuel, and of the fuels coal is of primary importance. The normal consumption of coal has increased greatly owing to the increased tempo of industry in general. It has been necessary to divert much of the fuel oil, gasoline, etc., ordinarily used for industrial and domestic purposes, to supply the enormous demands of mechanized warfare. Coal must be provided to replace this fuel. Furthermore, the enormous increase in the production of steel has increased the demand for coking coals to a critical point.The Solid Fuels Administration for War is encouraging the use of anthracite fines in the production of byproduct coke for blast furnaces for three reasons. First, the production of anthracite for domestic use; is hampered by the inability to find a market for the fines incidental to the production of domestic sizes. Second, the shortage of low-volatile coking coal is acute, and any action that will decrease the quantity of low-volatile coal required will relieve the situation. As will be seen in this report, there is some promise that use of anthracite fines in coke-oven mixes will lower the amounts of low-volatile coal required. Third, utilization of those anthracite fines will tend also to alleviate the general fuel shortage. It has been the privilege of the Bureau of Mines to cooperate with the Solid Fuels Administration in the technical problems involved."

Apr 1, 1945

In Broken Hill, Northern Rhodesia, two water jacket lead furnaces have been in operation for the past three years. The furnaces were erected in war time, and only absolute essentials were procurable. The water for the jackets was obtained from wells adjacent to the works, in a dolomite formation. There being no water-softening plant, except a small one capable of treating water for the power plant only, this water was found to make a heavy scale in the jacket. During 1917 several jackets were burnt through, resulting in serious trouble and loss of output. In order to avoid this, furnaces were stopped twice a month for 8 hours and scale was removed as far as possible. In addition to the scale trouble during the summer months, a green slime grew in the supply tanks and occasionally became detached from the tank and collected in the cocks near the jackets. This caused risk to the jackets and was difficult to remove without a stoppage of the furnace. In 1918, bundles of wattle bark were placed in the hot well at the rate of one ton per month. These extracted the tannin and added from 0.5 to one part of tannin per 100,000 to the circulating water. The hot water was cooled over a brushwood cooling tower and returned to the supply tanks. The well water required to, make up the wastage was estimated at 40,000 gal per day.

Jan 1, 1920

By A. Kazemi, M. A. Ahmadi

Pressure tunnels are constructed nurously in related with powerhouse. In some cases, according to high internal water pressure, rock mass around tunnel can seldom suffer this pressure. So installation of concrete lining which interacts with rock mass and suffers parts of this pressure and transfers the rest of the pressure to the rock. In this paper hydromechanical interaction between rock and lining is investigated. With using empirical and numerical methods concrete lining for Symareh waterway is designed. Initial support of 10 cm reinforced shotcret with wire mesh and rock bolts pattern of 2.5*2.5 m with length of 4 m is suggested. By using FLAC package final lining with paying attention to axial force and momentum in reinforced concrete was designed. Reinforced concrete with 60 cm thickness and two rows of bars, 18 mm diameter and 20 cm spacing are designed. Also for preventing cracks in concrete which caused by the change of temperature and shrinkage, bars with 10 mm diameter and 25 cm spacing, and also bars with 8 mm diameter and 10 cm as minimum shear bars are suggested. Plusieurs galeries en pression se construisent en liaison avec les centrales électriques. Dans certaines galeries, suite à une haute pression interne de l'eau, le massif rocheux autour de la galerie ne peut pas supporter cette pression. L'installation d'une couche de béton a l'intérieur de la galerie donc réagit avec les roches et support d'une partie de cette pression et transfère le reste de la pression aux roches. Dans ce papier, l'interaction hydromécanique entre la roche et la couche en béton a été étudiée. En se basant sur les méthodes empiriques et numériques le système de support de galerie de passage d'eau de Saymareh a été conçu. Un soutènement initial d'une épaisseur de 10 cm de béton étant renforcé par un grill métallique et une maille de boulon (2.5 * 2.5 m) d'une longueur de 4 m a été proposé. En utilisant le logiciel de FlAC, la couche finale en béton selon les forces dans le béton a été conçue. Le béton renforcé d'une épaisseur de 60 cm et deux ranges d'armateurs (18 mm de diamètre) avec un intervalle de 20 cm a été conçu. De plus; pour éviter des fissures dans le béton suite au changement de la température et de l'extraction, des armateurs de 10 mm de diamètre et de 25 cm d'intervalle pour augmenter la résistance au sciesiement du béton ont été proposes Unter Druck stehende Tunnels werden hauptsaechlich im Zusammenhang mit Kraftwerken gebaut. In einigen Faellen, wo der Wasserdruck zu hoch ist, Kann selten die Felsenmasse diesen hoehen Druck allein aufnehwen. Deshalb werden sie mit Betonauskleidung versehen, die wegen guter Wechelwirkung mit der Felsenmasse einen Hauptanteil des Druckes aufnehmen Kann, wobei der Rest an die Felsenmesse weitergeleitet wird. In dieser Arbeit wird die hydromechanische Wechelwirkung zwischen der Gesteinmasse und der Auskleidung untersucht. Mit Hilfe empirischen und numerischen Verfahren sowie Kombination der beiden wurde eine Betonauskleidung fuer die Symareh Wasser Kannal koustruiert. Als erstes wurde ein 10Cm dicker armierter Beton mit einem Mashengitter von 2.5*2.5 sowie den gleichen Felsbolzenabstaenden und einer Laenge von 4 m vorgeschlagen. Mit Hilfe des FLAC Programms wurde die Hauptauskleidung unter Beruecksichtigung von Axialkraeften und Momenten im Stahlbeton koustruiert. Der 60 Cm dicke Stahlbeton wurde mit zwei Reihen von Stangen, 8 mm im Durchmesser und in Abstaenden von 20 Cm koustruiert. Ferner im Sinne der Vorbeugung gegen Rissen im Beton, die durch Temperatur aendeungen und Schrumpfungen bedingt sind, wurden Stangen mit 10 mm Durchmesser und 2.5 Cm Abstaenden zur Erhoehung vor Scherfestigkeit des Betons vorgeschlagen.

Jan 1, 2003

By W J. Rankin, D R. Swinbourne

There are large tonnages of low-grade manganese ores in India fromwhich it is uneconomic to produce ferroalloys by conventionalsubmerged arc furnace smelting. A possible way to utilise these ores is to smelt them with carbon to produce pig iron and a manganese-rich slag, then to metallothermically reduce the molten slag to silicomanganese. Thermodynamic modelling of the metallothermic reduction stage using aluminium, silicon or aluminium-silicon alloy as the reductant at 1450¦C showed that an acceptable grade of silicomanganese could be produced. Manganese recoveries were predicted to be about 80 per cent. Heat balances indicated that silicothermic reduction may not produce enough heat to maintain reaction temperature. Small-scale laboratory experiments showed that the manganese grade of the alloys, and the manganese recoveries, were close to those predicted, but those for silicon were muchlower. Aluminothermic reduction produced the highest grade manganesealloy. The slag-metal equilibrium involving manganese, silicon and their oxides was investigated and it was found that equilibrium was not attained in any of the experiments, due probably to the very low rate of reactions involving silicon. This could be used to advantage in practice to achieve higher manganese levels in the alloys.

Jan 1, 1998