Search Documents

By G. Y. Chin, A. R. Von Neida

The relationship between crystalline texture and magnetic anisotropy in a Co-10 pct Fe alloy has been investigated by means of X-ray pole .figures, hysteresis-loop tracings, and magnetic-torque measurements. The cold-rolled texture of a sample after 95 pct thickness reduction is of the "brass-type", that is, (110)[112/. At 500°C the cold-rolled material recrystallizes fo a (311)[112] orientation, plus a minor (210) [001] component. This texture persists up to 1400°C, at which point it is replaced by a secondary recrystallization texture, (111)[112]. Magnetic-torque measurements show that the easy axis of magnetization lies along the transverse direction in the cold-rolled material and changes to the rolling direction after primary recrystallization. This change is also reflected in the hysteresis characteristic; whereas the B-H loop along the rolling direction is nonsqunre with a low value of residual induction (750 vs 19,000 gauss at saturation) for the cold-rolled material, the annealed sample exhibits a very square loop with a large value of residual induction (16,000 gauss). Theoretical torque curves calculated from the texture data on the basis of magnetocystalline anisotropy energy compare favorably with the observed torque curves. Values of the crystal anisotropy constant, K1, obbained from these comparisons are in good quantitative agreement with single-crystal data. Furthermore, both the torque amplitude of the poly crystalline material and the magnitude of K1 obtained with a single crystal show an identical temperature dependence over the range from —195° 10 +220°C. It is thus conclzided that the magnetocrystalline anisotrpopy erlergy is chiefly I-esponsible. for the nzagnetic allisotropy of textured Co-10 pct Fe alloy. THE results of a study on the relationship between crystalline texture and magnetic anisotropy of an alloy containing 90 pct Co and 10 pct Fe by weight are reported in this paper. The alloy has an fcc structure: a saturation magnetization of about 19,000 gauss,2 and a nearly zero value of magnetoatriction.3 puzey4 has reported a large crystalline anisotropy constant of -7.4 X 105 ergs per cu cm, indicating the (111) directions as the easy axes of magnetization. Hence, texture variations resulting from cold work and annealing are expected to introduce a magnetic anisotropy in the polycrystalline material through the alignment of these (111) easy directions. In the present study, magnetic anisotropy of both rolled and annealed strips was determined by magnetic-torque measurements and hysteresis-loop tracings The results were correlated quantitatively with calculations based on texture data obtained by the X-ray pole-figure technique. It is established that the magnetocrystalline anisotropy energy is indeed chiefly responsible for the magnetic anisotropy of textured Co-10 pct Fe alloy. EXPERIMENTAL Material Preparation. The alloy nominally contained 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn by weight, the chief impurities being nickel, carbon, and silicon (less than 0.5 pct total). The cast ingot was rolled to strips 10 mils thick and slit to 1 in. in width. After strand annealing at 900°C in a hydrogen atmosphere, these strips were further cold-rolled to various thicknesses down to 0.25 mil (97.5 pct reduction), with samples collected for study of the development of texture and magnetic anisotropy as a function of thickness reduction. subsequently, samples cold-rolled from 100 mils to 0.25 mil were obtained, thus extending the thickness reduction range to 99.75 pct. In addition, 0.5-mil samples cold-rolled from 10 mils were selected

Jan 1, 1965

By H. Guyod

The response of the Guard Electrode sonde (LL3) and the Laterolog (LL7) can be mathematically computed only for cases that do not represent realistic conditions. A resistance network analogue that simulates a number of typical—although idealized—formations was used instead to obtain, for both devices, a large number of resistivity logs and current distribution maps. From these data, charts were prepared for estimating true resistivities under a number of conditions. Some of these charts and current distribution maps are presented. INTRODUCTION Two main benefits are expected from a resistivity log: (1) obtaining geological information for mapping and other purposes, and (2) obtaining petrophysical data, based on true rock resistivity. The geological information can be derived from any resistivity curve having sufficient vertical detail, but true rock resistivities frequently are difficult to determine with desired accuracy because we do not have sufficient interpretation data. This is particularly true for the records given by the Laterolog tools. The object of this paper is to throw some light on the factors affecting the responses of these tools so that better resistivity data can be obtained from Laterologs. LATEROLOGS Laterolog measuring systems are of two types: the LL3 sonde, frequently called "Guard", and the LL7 sonde. Both measure the resistance between a single exploring electrode placed in the borehole and a faraway return electrode whose influence will be assumed here to be negligible. Although the principles of these tools have already been outlined,1-3 it is desirable to review them briefly in this article. LL3 Fig. 1, left side, represents a long cylindrical, vertical current electrode placed in a medium of uniform resistivity. The current leaving the center section of the electrode flows essentially along horizontal lines, delineating a surface having the shape of a biconcave lens. It is the elec- trical resistance offered to this particular group of current lines that is measured by the Guard tool. This is done in practice by having a long cylindrical electrode consisting of three sections physically and electrically separated by thin insulating washers, as shown in the center of the figure, and keeping the three sections at the same potential. It is obvious, for all practical purposes, that the current and potential distributions about this electrode are the same, as if we had a continuous electrode of same dimensions. Because the three sections are electrically separated, the resistance seen by the center section E can be independently measured. This section will be called the exploring electrbde, or E electrode. Its height generally is from a few inches to 1 ft. The outer sections are the guards G, which are several feet long. The combined length of the three sections is from 10 to 12 ft for the tools currently used in the petroleum industry. Let V denote the potential difference between E and the faraway return electrode, and I be the current flowing between these two electrodes. The resistance (Re) seen by the exploring electrode is VII, and the corresponding apparent resistivity is Ra = k(Re),............(1) where k is the tool calibration factor. The previous description establishes that the Guard tool uses that central portion of the sonde from which, in a uniform medium, the current follows essentially horizontal paths. When the formation being logged is fairly uniform, and when its resistivity is of the same order as

Jan 1, 1965

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.' More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.' The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.' Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.

By L. L. Newman

PUBLIC UTILITY GAS PRODUCTION IN 1802, William Murdock first used retort coal gas to light his house and the Boulton and Watt plant where he was employed. For the next three quarters of a century coal served as the principal raw material for the manufacture of city gas for general distribution. Coal continued to hold its predominant position for another half century after Prof. Thaddeus C. Lowe developed the first practical method of enriching water gas with cracked-oil vapors in an integrated operation. This position, however, was no longer maintained through the medium of direct carbonization of coal in retorts but as a result of using anthracite or coke as the generator fuel in carburretted water-gas machines. The early water-gas machines were extremely crude and the consumption of both oil and generator fuel was very high. However, the cost of installation was considerably lower than for any coal-gas system having the equivalent gas-making capacity, the labor involved was small, and the water-gas machine could be started up and shut down quickly. It thus proved very useful as standby equipment and in taking peak loads from the coal-gas plants. The flexibility of the water-gas machine, furthermore, made it possible to change the candlepower of the gas readily to suit the required conditions. Later, when calorific value replaced candlepower as the standard of gas quality, the water-gas machine was found to be equally flexible in keeping the city gas under complete and convenient control. No basic improvements were made in the Lowe carburetted water-gas process until 1898, when means were added to provide for regular reversals of the flow of steam through the fuel bed. By judicious proportioning of the quantities of up-run and down-run steam, it became possible for the operator to control the hardness and position of the clinker to a degree that previously had been unattainable. Also in 1898, the first by-product coke plant in America to supply city gas was built at Everett, Massachusetts. Later many other by-product plants, of greatly improved design and capacity, were built, but not primarily for city-gas production, chiefly because of the relatively high investment cost per unit of gas made. Cheaper plant construction has been the subject of serious study, and some progress is expected, but other factors, such as plant life,

Jan 1, 1953

By S. C. Langdon, Henry S. Rawdon

The following note describing the behavior of copper under rather unusual conditions is offered for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning, as well as softening it. It is well known that metals may be rendered very brittle by electrolytic action in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear 2 similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. TO demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 801" C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for several minutes. When removed from the bath, cooled, and tested for brittleness by bending the specimen back and forth, while clamped firmly at one end in a vise, the copper rod was found to be very brittle, as compared with a rod of the same length of the untreated copper tested

Jan 1, 1921

By R. F. Mehl, W. Batz, C. Wells

Diffusion coefficient values for carbon in austenite covering a wide range of temperature and composition have been determined employing statistical methods. In addition, the relation between concentration and each of the following, D (diffusion coefficient), Q (activation heat of diffusion), and A (the constant in the diffusion equation), has been obtained. A study of the rates of diffusion of austenite was published in Metals Technology in 1940.' The present investigation is an extension of the earlier work, undertaken (1) to obtain values of the coefficient of diffusion, D, over a much wider range of carbon concentration, and (2) to provide data in all ranges of concentration and temperature in such abundance that statistical methods could be employed to evaluate the accuracy of the data with unusual precision. Composition of Materials: Composition of materials used in this research program are listed in table I. These materials, all forged to about 1 1/4 in. rounds, consist of a high-purity iron, Armco iron, a large number of laboratory-made plain carbon steels containing amounts of impurities normally expected in high-quality commercial steels, and three silicon steels. Since it was known at the time these steels were being made that impurities in the amounts present were unlikely to affect carbon diffusion rates' significantly, the effort made to obtain high-purity steels was not as persistent as it otherwise would have been. Procedure: In general, the procedure followed by Wells and Mehl and described' in detail in an earlier publication' is the one used by the present authors. However, certain modifications have been made which it is believed allow diffusion data to be interpreted more objectively and correctly. These are described completely under appropriate subheadings which follow. Experimental Procedure: Experimental procedure includes (1) the preparation of specimens by welding steels of different carbon contents, (2) the heating of these for certain times at selected temperatures in order to diffuse carbon along the specimens across the welded "interface," and (3) the determination of the carbon distribution across the diffusion zone. Preparation of Specimens: Prior to welding steel of one carbon content to iron or steel of another carbon content, surfaces to be welded are machined perpendicular to the longitudinal axis of cylinders which are about 3/4 in. in diam and 1 1/2 in. long. The prepared, flat, parallel surfaces are brought together and butt-welded electrically. Evidence of a good weld is given in fig. 1. Welding temperature

Jan 1, 1951

By E. T. Turkdogan

This paper deals with an analysis of the conditions leading to the formation of blowholes and surface and subsurface defects in cast low-carbon steels. The theoretical analysis of the problem is based on the concept of the occurrence of deoxidation reactions during cooling of liquid steel and during its solidification. The reaction equilibrium data are given on deoxidation of steel by carbon, silicon, and manganese. The details of the calculations are given on the simultaneous deoxidation of steel by silico-manganese additions to produce a desired level of deoxidation at certain residual concentrations. Based on an idealized model, an attempt is made to calculate the enrichment of solutes in the solidifying liquid entrapped within the interdendritic cells which are known to be less than 200 µ thick. Formulae are derived for the calculation of the change in the residual oxygen content of the enriched liquid steel, controlled by Si/Mn deoxidation. It is shown that for every particular initial silicon, manganese, and oxygen concentration in steel (as residuals in liquid solution at the beginning of solidification) there is a particular carbon concentration below which carbon monoxide, leading to blowholes or pinholes, is not expected to form. There are a number of independent variables which have a decisive influence on the formation of blowholes. For example, it is shown that the position of the curve depicting the critical relation between initial silicon and carbon content for suppression of the evolution of carbon monoxide) can be shifted to lower silicon or higher carbon levels by: increasing manganese content; decreasing oxygen, hydrogen, or nitrogen content; or increasing external pressure on the solidifying mass. FOR the production of sound castings it is essential to prevent the formation of interdendritic worm-holes or pinholes brought about by gas evolution during solidification. Another major problem encountered in solidification of ingots is the formation of surface defects. These problems are thought to be closely associated with the deoxidation reaction occurring in liquid steel during cooling and subsequent solidification. As the liquid becomes richer in impurities during dendritic solidification of steel, a series of reactions may occur in the liquid phase trapped within the branches of growing dendrite platelets. Because of the strong interaction between dissolved oxygen and impurities in liquid steel, the reactions most likely to occur are of the deoxidation type. However, inherent to the extreme complexity of the problem in question, numerous simplifying assump-

Jan 1, 1965

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

By C. S. Blair

The development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Alabama, in 1908 was an innovation probably unique for any mining organization south of the Ohio River. At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator difficulties in his future operations, which the latter had not anticipated. Eventually, however, the value of having these data became apparent to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1935

By D. L. Wood, J. H. Westbrook

The tensile behaviors of the CsCl structure compound AgMg are extensively documented in terms of strain, strain rate, temperature, composition, and metallurgical processing treatment. The observations lend themselves to presentation in terns of three regimes of deformation behavior; 1) low temperatures where deformation is primarily by slip; 2) intermediate temperatures where the deformation mode is also slip but with the detailed behavior dominated by dislocation interactions with solute atoms; 3) high temperatures where defomation is primarily by diffusion controlled processes. Of all the material groups of potential interest as high-temperature structural materials, the inter-metallics have been the least studied, particularly with respect to their mechanical behavior. Moreover, the application and processing of intermetallics for uses which exploit their often unique physical properties have been impeded by a lack of understanding of their mechanical properties. Previous work in this area* has been largely *For a recent review, see Westbrook.' exploratory, aimed on the one hand at the direct empirical development of materials of engineering utility and ,on the other at identification of the important parameters affecting the mechanical behavior of inter metallics. As a consequence, there has not been available, heretofore—for any inter-metallic—data, sufficient in extent or precision to provide an adequate phenomenological description of the effects of metallurgical variables on deformation behavior. Such documentation is prerequisite to intelligent application or processing design and is also necessary for testing present and future theoretical analyses of mechanical behavior. It was therefore an objective of the present investigation to document the deformation behavior of a simple ordered intermetallic over as wide a range as possible of all the usual metallurgical variables. The compound AgMg was chosen as the subject of this investigation because it met all of a group of desired criteria, namely: 1) congruent but moderate melting point; 2) simple crystal structure; 3) ordered structure persisting to the melting point; 4) broad solubilities for the component elements. The first and last criteria were expected to aid in the preparation of homogeneous single-phase specimens: the second and third to help simplify the

Jan 1, 1962

By Clarence E. Sims, George A. Moore

INTRODUCTION IN previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficient time is allowed. For precise work, the method claims preference because the equipment for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the transformation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approximately 2 hr. While it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual error may be more or less constant between samples. For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temperature process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and evolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1948

By A. B. Hildebrandt

P. B. Baxendell is to be complimented for an exccllent piece of work. To our knowledge there has been no previous publication of field data on the flow of oil and gas through the annulus of a well. It is certainly gratifying to see this work on annular flow confirm the previous published correlation procedure on tubing flow. It extends considerably the range under which reliable gas-lift calculations can be made. Baxendell discussed this work with us about a year ago and was kind enough to send a large scale plot of his correlation. We had been designing gas-lift installations on flow through the annulus, assuming that the original correlation of the f factor based on tubing flow' was valid as long as we stayed within the same mass velocity range on which the correlation was based. Doing this work necessitated the use of an equivalent diameter for the annular flow. The equivalent diameter is defined as area' of stream cross section wetted perimeter and for the case of an annulus is D, — D,. Substituting this in the basic equation correlating energy loss along with the area to flow required to convert the velocity, to volumetric flow rate, D (Baxendell's Eq. 7) becomes dell's expression, D,). Similarly, the D in 1.4737 X 10 (M&/D) becomes (D, + D;) for annular flow. On receipt of Baxendell's data, we. of course, recalculated it to put it into the form we were using, and to see how well it agreed with the correlation based on tubing flow. Fig. 1 shows the results, which were certainly gratifying. For low values of (D, - D,) pv, the data coincide with the data on flow through tubing, whereas at high values the data on flow through the annuli appear to be leveling off to a constant value. For very high rates of flow where the turbulence is very high, one might expect the value f to level out and become constant. A bulletin published in 1914 by the U. of Wisconsin presented results of a large number of laboratory teats in air lifting water through short lengths of 1.25-in. tubing. It was possible to correlate a random sampling of

By Chas. A. Dobbel

The Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. Pmine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the Gear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was used to drive prospect holes with jointed steel. Just what equipment to develop for this work with the hammer drill involved much experimenting, as nothing was found in the literature

Jan 1, 1925

By M. A. Mayers, J. A. Thompson

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble's C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By C. S. Yust, J. W. Smith, J. R. Walsh, R. E. Simpson

This paper presents the results of a complete reservoir studv designed to determine a sound economic program for the conservation of oil and gas in the Pickton field, Hopkins County, Texas. The Pickton field produces from the Bacon Lime with all indications of the study being that production is predominately by dissolved-gas drive. Calculations of the total ultimate recovery to be expected under primary operations indicated only 16.7 per cent of the oil originally in place would be recovered. This unusually low recovery is due to the type of drive operating and the extremely high dissolved gas-oil ratio and shrinkage. Results are presented for six plans of returning gas to the reservoir, evaluated to determine (1) comparative recoveries and economics of (a) returning gas at a constant rate by supplementing Pickton gas with extraneous gas during the early portion of the operation, and (b) conventional gas-return operations without using extraneous gas, and (2) the optimum size of compressor plant for each type of pressure maintenance. The over-all economic program considers, for either type pressure maintenance operation. a gasoline plant to process the unusually rich casinghead gas. Since pressure maintenance will disturb equities, pooling of royalties is in the case of Pickton a prerequisite to conservation of oil by this type of operation, both from an economic and legal standpoint. In the event pooling of royalties cannot be achieved, the study considers a gasoline plant to operate under a modified primary production operation which will make the conservation of gas possible. INTRODUCTION The Pickton field, located in Hopkins County, Texas. was discovered in November, 1944. by the completion of Humble's C. D. Nichols 1, in the Bacon lime of the Lower Glen Rose formation, through perforations from 7,888 to 7.896 feet. The well initially produced 50.2 API gravity oil with a gas-oil ratio of 1,350 cubic feet per barrel. Subsurface samples of the reservoir fluid obtained soon after completion of the discovery well showed that the Pickton crude is unique in that it has an extremely high dissolved gas-oil ratio and is subject to very severe shrinkage. Calculations of the future behavior of the Pickton reservoir indicated that ultimate oil recovery by primary operations would be 3,269,000 barrels, representing only 16.7 per cent of the oil in place (19,577,000 stock-tank barrels), and that recovery could be substantially increased by returning the produced gas. The cumulative production of 1,382,694 barrels on November 1: 1947, amounted to 42.3 per cent of the estimated ultimate oil recovery from primary operations. The purpose of this study is to determine and evaluate the optimum program for conservation of oil and gas in the Pick-ton field, including the desirability of conducting gas-return operations and of installing a gasoline plant. LOCATION AND DESCRIPTION Pickton Field, The Pickton field, as shown in Fig. 1, is located in southwest Hopkins County, Texas, 12.5 miles southwest of the New Hope field, 2.7 miles northeast of the Coke field, 16 miles southwest of Sulphur Springs, and 8 miles northwest of Winnsboro, Texas.

Jan 1, 1949

By J. A. Thompson, M. A. Mayers

In recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.l-14 Only in Russell's method" and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼-in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C, consisting of two annuli of 0.011-in. (o.a8-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By E. W. Stewart, G. P. Conard, J. F. Libsch

The effects of several additives upon the reduction characteristics of hydrogen-reduced ferrous formate are described. The various additives inhibit sintering of the reduced iron particles by apparently different mechanisms. The magnetic properties of the low density compacts produced from the resulting ultra-fine iron powders were improved markedly. THE permanent magnetic characteristics of ultra-fine iron powder prepared by various means have been a subject of considerable interest and experimentation in the past few years. When such particles are small enough to show single domain behavior, they possess' 1—permanent saturation magnetization, and 2—high coercive force. In the absence of domain boundaries, the only magnetization changes in a particle occur through spin rotation which is opposed by relatively large anisotropy forces. With decreasing particle size, the coercive force tends to increase to a maximum and then decrease because of the instability in magnetization associated with thermal fluctuations. Kittel' has calculated the critical diameter at which a spherical particle of iron can no longer sustain domain boundaries or walls to be approximately 1.5x10-' cm. Stoner and Wohlfarthr in England and Neel4,6 in France have shown from purely theoretical calculations that the high coercive force expected from single domain particles is dependent upon crystal anisotropy, shape anisotropy, or strain anisotropy contributions. Further work by Weil, Bertaut,' and many others has contributed much to the understanding of fine particle theory. Neel and Meikeljohn" have demonstrated that a decrease in particle size below a critical value of approximately 160A leads to a quite rapid decrease in coercive force because of the prevention of stable magnetization by thermal agitation. Lih1, working with powders prepared by the reduction of formate and oxalate salts of iron, has shown the marked influence of powder purity upon magnetic properties. Maximum coercive force was obtained in powders of approximately 65 pct metallic iron content while the maximum energy product, (BxH) occurred in powders of 85 pct metallic iron content. Careful consideration of the preceding theoretical considerations and experimental results has led to the manufacture of permanent magnets from ultra-fine ferromagnetic powders by powder metallurgy techniques. Such work has been done by Dean and Davis," the Ugine Co. of France, and Kopelman." The aforementioned work of Kopelman and the Ugine Co. was concerned somewhat with the effect of various additives upon the properties of hydrogen-reduced ferrous formate. Virtually no work, however, has been published on the effects of additives on the reduction rates of metal formates, although unpublished work by Ananthanarayanan16 howed promise of improved energy product in ultra-fine iron compacts prepared by the hydrogen reduction of a coprecipitated mixture of magnesium and ferrous formate. After consideration of the preceding information, it was hoped that a better balance between the metallic iron content and particle size of the reduced iron powder could be accomplished by a prevention of the attendant sintering of the partially reduced iron powder during the reduction reaction. It appeared possible that magnesium oxide might interpose a mechanical barrier between adjacent iron particles and prevent their sintering together, while metallic cadmium and metallic tin would interpose a liquid barrier which might accomplish the same purpose. The degree to which these materials were effective in accomplishing the foregoing objective and the experimental details associated with the work are reported in the following sections of this paper. Experimental Procedure Preparation of Formate and Oxide Mixtures: To obtain ferrous formate of reproducible reduction characteristics, a slight modification' was made in the technique of Fraioli and Rhoda." A supersaturated solution of ferrous formate was mixed with an equal volume of 95 pct ethyl alcohol and the formate crystals precipitated by stirring and screened to —325 mesh. These crystals were in the shape of elongated hexagons, approximately 4x10 micron in dimension. Various preparations of such ferrous formate, designated as lot 111, were reduced for 2 hr, yielding ultra-fine iron particles of exceedingly reproducible size, metallic iron content, and magnetic properties. The magnesium and cadmium formates were prepared by the reaction of dilute formic acid with their respective carbonates, while the tin formate was prepared by the reaction of dilute formic acid with stannous hydroxide. To evaluate the effect of metallic formate additives in intimate mixture with the ferrous formate, varying amounts of magnesium, cadmium, and tin formates were coprecipitated with the latter. The designations of these materials and their chemical compositions are given in Table I. Due to the differing solubilities of the various formates in aqueous media,

Jan 1, 1956

By F. Keller, A. H. Geisler

ALTHOUGH the subject of precipitation from solid solution appears to be one of the more profitable fields in metallurgy for study with the electron microscope, few comprehensive studies have yet been made. Occasionally electron micrographs have been published that illustrated alleged precipitation in various alloys, but frequently the apparent size, shape and distribution of the particles do not fully agree with those expected from theory or from observations of the precipitate when the particles have grown to a size resolvable with the light microscope. The presence of a Widmanstätten pattern for submicroscopic precipitate particles has been demonstrated for only a few aged alloys.1 The initial problem has been the development of suitable techniques for applying the transmission-type instrument to a field that has been inherently associated with reflection-type microscopes. The various techniques have been the subjects of numerous publications, and instead of describing them individually here it will suffice to say that the oxide film method has proved to be the most satisfactory method yet found for studying the microstructure of aluminum alloys with the electron microscope. This method has the definite characteristic advantage that the actual surface layer of the specimen is examined and not a plastic or silica replica. Doubtless suitable methods for forming and removing the oxide film could be developed for alloys of other metals. The purpose of this report is to point out the characteristics of the oxide film method that have been observed during the studies of numerous aged aluminum alloys and to present the results of these studies. PREPARATION OF SPECIMENS The oxide film method for preparing specimens of aluminum alloys for examination in the electron microscope has been described in detail previously.1,2 Briefly, the procedure consists of preparing the metallographic specimen, forming the film by anodic oxidation and removing the film from the prepared surface of the oxidized specimen. The specimen is polished according to the usual procedure for microscopic examination.3 The specimen may then be etched to remove flowed metal but etching to attack the alloy constituents or to leave them in relief as in the replica processes is not necessary. Electrolytic polishing is not generally recommended. Deep-etched specimens are used frequently, however, since they provide information that is not revealed by polished specimens and frequently present the same information more clearly than do the polished specimens. The surface preparation of specimens to be deep-etched is not important, since specimens that have been subjected to the first wet polishing operation are generally used, but frequently the as-rolled surface is suitable. These specimens are then etched using a suitable macroetching reagent.

Jan 1, 1946

By David V. Ragone, Richard E. Balzhiser

The liquidus uranium concentration in the U-Bi system is given by the following expression for the temperature range 400° to 800°C: No break was observed in the curve over this temperature range. The partial molar enthalpy change for uranium in the liquidus reaction, UBi2— U + 2Bi, was found to equal 12,300 cal per g mole. Copper produced a continuous decrease in the liguihs uranium concentration at 600°C. The presence of copper in the solvent was observed to affect the uranium activity coefficient according to the following expression: duced no change in the liquidus combosition below 0.6 at. pct Pd. Higher palladium concentrations sharply depressed the uranium concentration. SOLUTE behavior in molten alloys has been shown to be strongly influenced by the presence of additional species. Much attention has been given to such phenomena in iron-base systems where a number of alloying elements and/or impurities are likely to be present in small but significant quantities. Frequently, the interaction of these solutes has altered their thermodynamic behavior to the extent that reaction equilibra are appreciably influenced. Consequently, much of the information available for binary behavior must be reevaluated when additional components are likely to be present. Similar interactions can be expected to occur in bismuth-base solvents. Interest in the use of bismuth solutions of uranium as reactor fuels has stimulated investigators to explore the effect of various elements on the liquidus uranium concentration. Criticality requirements necessitate close control of the uranium concentration which, at the anticipated operating temperature of 500°C, approaches saturation. Consequently, elements which suppress the liquidus concentration could produce serious reactivity problems. Since the fuel solution is cer- tain to contain additives, such as magnesium and zirconium, for corrosion inhibition as well as small concentrations of fission products and corrosion products, a better understanding of the possible interaction phenomena is mandatory. This need stimulated experimental programs at the Brookhaven National Laboratory and elsewhere to determine precisely the liquidus uranium concentration in the bismuth-rich portion of several ternary systems. Early experimental efforts were directed toward an accurate dcmtermination of the U-Bi liquidus over the temperature range from 300' to 800°c. As shown in Fig. 1, the results to date exhibit considerable scatter. The investigations of Bareis,' Teitel,2 Greenwood,3 and Cotterill and hon4 agreed well below 700°c. Greenwood and Teitel extended their studies to higher temperatures but failed to concur in their results. A more recent study by Schweitzer and weekss at Brookhaven National Laboratory between 300' and 725°c, produced values 15 pct lower

Jan 1, 1962