Search Documents

By W. M. Myers

Certain minerals possess inherent color and other properties that make them suitable for the pigmentation of paints, mortar, plaster, concrete, face brick, and other materials. Their production is one of the most ancient of mineral industries and their use by primitive man is well known. These natural pigments have some economic factors in their favor, particularly wide geographic distribution, low cost of production, ease of preparation, chemical stability, and permanence in use so that they continue to form the basis of a small but useful industry. When used in paints such pigments act as a filler and supply body and opacity in addition to color. Natural mineral pigments are prepared for the market by the comparatively simple operations of washing, grinding, blending, and calcining. Any one, or all of these processes may be applied to a single pigment. The development of synthetic pigments and the use of by- product materials have introduced competition with the products of nature and are having a growing influence on the economic position of the mined minerals.

Jan 1, 1949

By George H. Jones

NO STRANGER phenomenon exists in the American mining industry today than the so-called bootleg anthracite industry in Pennsylvania which now produces probably close to 15 per cent of the total hard coal out- put of the State. Instead of being what - was first thought to be a temporary condition, countenanced because of the desperate condition of some of the miners at the depth of the depression. it is thriving now as never before. Re- ports of it have penetrated all over the world, as exemplified by inquiries concerning it in Durban, South Africa mentioned by John C. Cosgrove in his article in the July MINING AND META LURGY.

Jan 1, 1939

By Ian MacGregor

As I drove in from the airport on Sunday somebody said 'On the right you will see Duntroon, which is the military training school of Australia.' So I asked the driver, where did they get that name? 'Oh,' he said, 'from some people who built a house there. That was it's name- Duntroon.' It strikes a note with me because, that's the name of a 12th century castle on the west coast of Scotland where I spend what leisure hours I have and, therefore, it establishes the long connection between Australia and my native land. There is also a story I should tell you about the oil industry and its upsurge in Scotland recently which has resulted in great prosperity. And in Edinburgh, the walls of the banks are bulging-because of the incursion of foreign exchange and other resources. Charlotte Square, as some of you know, is the centre of the Scottish financial world and at one of the corners of Charlotte Square, where ho streets intersect, there are three stores-three emporia on the ground floor. Two of them at opposite corners are banks: The Royal Bank of Scotland, and not to be beaten by that, The Bank of Scotland. But the third building is occupied, or was occupied, by a furniture store over many years-very high-grade, high quality furniture that the elite of the Edinburgh society always supported. And suddenly, the store was cleared out and in came a bunch of carpenters and other people busily engaged in rebuilding the store, and finally the new tenants arrived on the scene.

Jan 1, 1978

By R. C. McFarlane, T. D. Mueller, J. E. Walstrom

In evaluating uncertainty, experiments are usually performed repeatedly and then conclusions are drawn from the distribution of results. With the advent of high-speed electronic computers, it is possible to perform experiments using mathematical models constructed to simulate complex experiments or operations. Statistical methods are then applied to the results of the simulated experiments. This procedure forms the busis of this paper. Demonstrated is the need for properly accounting for uncertainty in petroleum engineering problems. How uncertainty affects solutions is evaluated in three example illustrations. The method used to evaluate uncertainty in petroleum engineering studies is the Monte Carlo simulation procedure.'-" INTRODUCTION The solution to most technical problems may be derived from interrelationships among several quantities called variables or parameters. There may be only a few variables or several hundred. Interrelationships among parameters may be explicit or implicit, well established or only approximate. Some variables that fully or partially depend on the magnitude of others are called dependent variables. Input variables for most practical problems are not precisely known; there is usually an uncertainty in their value. The degree of uncertainty may vary from one variable to another. Variables that are known accurately are called determinates.' For instance, the gravity of crude obtained from a particular pool may be known precisely, and therefore is a determinate. The degree of precision with which a quantity can be determined increases as data describing the pool are accumulated during the development of the field and the producing life of the pool. The uncertainty of a parameter may result from difficulty in directly and accurately measuring the quantity. This is particularly true of the physical reservoir parameters which, at best, can only be sampled at various points, and which are subject to errors caused by presence of the borehole and borehole fluid or by changes that occur during the transfer of rock and its fluids to laboratory temperature and pressure conditions. Uncertainty may also result in attempting to predict future parameter values. This type of uncertainty is particularly evident in investment analyses involving future costs, prices, sales volumes and product demand. Uncertainty in the solution to investment problems is often called risk, and its study is called risk analysis.' Uncertainty also enters into biological and sociological analyses in which indeterminate factors are often important due to limited control of the experimental material. It is customary, in evaluating uncertainty, to perform repeated experiments and to draw conclusions from the distribution of the results of these experiments. With the advent of the high-speed electronic computer, it is possible to construct mathematical models which simulate complex experiments or operations and to perform the experiments repeatedly, utilizing the models. Statistical methods are then applied to the results of the simulated experiments This method forms the basis of the investigation reported here. PROBABILITY DISTRIBUTIONS FOR VARIABLES The uncertainty in the value of a variable may be indicated by a probabilistic description accomplished by expressing the quantity by a probability distribution. Many recognized probability distributions can be used to describe physical quantities. Recent studies used various types of distributions to describe core analysis data.',' However, for the examples in this paper, the uniform and triangular distributions are believed to reasonably approximate the data used (Fig. 1). The uniform distribution confines the variable between an upper and a lower limit. The variable may lie anywhere between the two limits. This distribution is used when no one range of values for a variable is more probable than any other, but information or intuitive reasoning indicates the variable will lie somewhere between the chosen limits. The triangular distribution is used for a variable when more data are available to indicate a central tendency of distribution. This allows postulating a "most likely" value to the distribution and upper and lower limits. In this case, as for the uniform distribution, the variable is not expected to assume a value less than the lower limit or greater than the upper limit. However, with improved quality of data it can be postulated that the variable will tend to assume a value close to the most likely value, and that there will be a decreasing probability for values away from the most likely value. The area under either of these probability distributions is equal to unity since it is assumed that there is a 100 percent probability that the variable will lie somewhere under the curve. An ordinate erected at any particular value of the variable divides the area under the curve into two parts: the area to the left of the ordinate represents the probability that the value of the variable will be equal to or less than the value of the variable at the position of the ordinate, and vice versa. The probability is zero that the variable will have any specific deterministic value. If two ordinates are drawn for any two values of the variable, the probability that the variables will have a value lying between these ordinates is equal to the area under the curve lying between the ordinates.

By James H. TaVoularis, William J. Wiehagen

This paper discusses the application of commercially available microcomputers for assisting trainers in the delivery and evaluation of new hire, refresher, and occupational training. A brief overview of mine training highlights major issues facing the mine training community. The use of computer-based training has a potential for reducing costs and improving the transfer of conventional training to the job.

Jan 1, 1983

By R. A. Haney, S. J. Gigliotti

Over the past ten years, analysis of the acceptability of face ventilation systems has been based on numerical criteria rather than solely a study of air flow and methane patterns in the face area. This type of analysis has become possible primarily because of the instrumentation and mathematical models developed by the Ventilation Division, Pittsburgh Health Technology Center, Mine Safety and Health Administration (MSHA). To properly use these mathematical models, large amounts of methane and airflow data must be collected in the face area during mining activities. To supplement underground testing of face ventilation systems, a full scale model of a face area was built. This model includes a full scale model continuous miner, a face ventilation system, a gas release system, and a remote methane detection system. The remote methane detection system consists of an array of twelve methane sensors located throughout the face area. Data from the sensors are transmitted to strip chart recorders. Methane, air quantity, and other data collected during a test are entered into a computer for analysis. This paper presents the data entry system, the models used for data analysis, the test results, and the application of these results to a face ventilation system.

Jan 1, 1983

By Thomas Henderson

Strategically, intermaterials competition is important to companies involved in raw materials extraction, smelting, refining or other processing, semi-finished and finished goods fabrication, and end-use consumers. In other words, just about every company involved in manufacturing. The array of materials covered by other papers in this session is testimony to the subject's breadth. In trying to provide an over- view of such a broad topic, the purpose has been to relate some of the common characteristics of the markets, economics and technology of raw materials, and to describe some of the ways in which Intermaterials competition impacts the markets, economics and technology of raw materials.

Jan 1, 1982

By Lo-Ching Chang, J. Chipman

The perennial and increasing interest in the chemical behavior of steelmaking slags has led to numerous attempts to formulate the thermodynamic properties of these solutions. The classical view is that of a solution of the component oxides in which certain acidic oxides are more or less completely held in combination with basic or metallic oxides, the nature of the interoxide compounds being derivable from the chemical behavior of the slag or from the mineralogy of a solidified specimen. The known electrical conductivity of slags has pointed to the existence of ions in the solution and a number of attempts have been made to account for the observed facts of slag behavior on the basis of a theory of complete ionization of the solution. It is the purpose of this paper to examine, in the light of ionic theory, a number of recently published series of data on slag-metal and slag-gas equilibria, with the purpose of obtaining a more complete or more satisfactory generalization than has been possible on either of the single bases of simple compound formation or complete ionization. The attempt to formulate the ionic constitution of a complex solution is fraught with many uncertainties. An ion is not something that can be plucked from the solution and examined in detail, nor can its true formula be determined with certainty by any single experimental method. In attempting to express the composition of a slag by various ionic formulas it can be expected that alternative hypotheses of essentially equal merit will present themselves. In the present state of early development of the ionic theory of slags, it may be necessary to make some rather arbitrary choices of ionic formulas in the absence of su- cient information to yield complete certainty. Acids and Bases The classification of slag-forming oxides as acidic or basic apparently dates back into the days of Berzelius. It is difficult to see how the concept could have originated in the early twentieth century when it was fashionable to define an acid or a base as an aqueous solution containing hydrogen or hy-droxyl ions. It is, however, entirely consistent with the modern and more general theory of acids and bases. In this theory, as originally formulated by G. N. Lewis,' a basic molecule is one that has an electron pair which may enter the valence shell of another atom thus binding the two together by the electron-pair bond. An acid molecule is one which is capable of receiving such an electron pair into the shell of one of its atoms. The acid, the base, and the product of neutralization may be either ions or neutral molecules. The product of such a reaction may itself be a base or an acid if it is further capable of giving or accepting an electron pair. Thus a base is a donor of electrons, an acid, an acceptor. In oxide slags the typical and ever-present base is oxide ion, 0-—. In behavior and in importance it is analogous to hydroxyl ion, OH-, which is the typical base of aqueous solutions. There is nothing in the chemistry of slags which is quite analogous to the acid H30+ in aqueous solutions. This is not surprising for in slag systems there is nothing which can be designated as a solvent and no ubiquitous positive ion. The chemistry of slags is in fact more complex than the chemistry of aqueous solutions and the concepts which must be evoked in its study are correspondingly broader. In seeking a basis for a classification of slag-forming oxides as basic or acidic it must be remembered that these terms are not absolute but relative. A substance which acts as a base toward a second substance may act as an acid toward a third. This is less likely to happen among strong bases or acids than among the weak ones; there are numerous examples of weak acids which under the influence of a stronger acid behave as weak bases. Such substances are called amphoteric. A classification of the glass-forming oxides has been proposed by Sun and Silverman² and further developed by Sun3 in which the oxides are arranged in order of decreasing acidity or increasing basicity, each substance being potentially capable of acting as an acid toward substances below it in the list and as a base toward those above it. It is based upon the relative strengths of the metal-to-oxygen bond as determined by the energy required to dissociate the oxide into its component atoms.' Data are available for computation of this energy, at least approximately, for the oxides of slags and glasses. In general those oxides from which it is most difficult to remove the positive atom are the strong acids while those in which it is most loosely held are the strong bases. It is in the latter, of course, that formation of oxide ion occurs most readily as, for example, in CaO which in solution ionizes to form the weak acid Ca++ and the strong base O—. The order of arrangement found by Sun is shown in the first column of Table 1, to which have been added the data for

Jan 1, 1950

By George M. Schwartz, Ian L. Reid

THE Soudan mine in the Vermilion district of northeastern Minnesota is the oldest iron mine in the state. It has shipped ore every year since 1884 and still contributes a yearly quota of high grade lump ore. No comprehensive report on the Vermilion iron-bearing district has appeared since Clements' monograph,' but Gruner2 discussed the possible origin of the ores in 1926, 1930, and 1932, and recently Reid and Hustad have added data on mining and geology .3, 4 For many years geologists of the Oliver Iron Mining Div., U. S. Steel Corp., have kept up to date a series of plans and vertical sections of the Soudan mine. In connection with mine operation considerable diamond drilling has been done, and this, together with the mine openings, has permitted a reasonably accurate picture of the structure of the orebodies and wall rocks. It has long been evident to geologists familiar with the mine that the ores were not a result of weathering, a point emphasized by Gruner in 1926 and 1930. As the deeper orebodies were developed it also became clear that replacement had played an important part in their development. In recent years it has been recognized that other iron ores were formed by replacement, as Roberts and Bartly5 have argued strongly for the deposits at Steep Rock Lake. On the basis of these facts G. M. Schwartz suggested to members of the Oliver staff that it would be desirable to study the evidence of replacement, particularly the possible alteration of the wall rock which would be expected if the replacement was a result of hypogene solutions. Rock Formations: The formations directly involved in the iron orebodies of the Soudan mine are few though far from simple. The country rock is largely the Ely greenstone of Keewatin age consisting of a mass of metamorphosed lava flows, tuffs, and intrusives which have been more or less altered by hydrothermal solutions. The predominant rock is chlorite schist. Interbedded with the original flows and tuffs are a series of beds and lenses of jasper to which the name Soudan formation has been applied. In the Vermilion district the term jaspilite has been used for interbanded jasper and hematite. According to modern usage these jasper or jaspilite beds do not comprise a formation separate from the Ely greenstone, inasmuch as the beds of jasper are interbedded with the flows and tuffs of the upper part of the greenstone. It would more nearly accord with modern usage to consider the Soudan beds a member of the upper part of the Ely formation. Because of incomplete rock exposure and exploration the number of interbedded jaspilite beds is unknown. In the mine, however, as many as nine major beds of jasper are known on a cross-section of one limb of the syncline, with an equal number on the other limb. In addition diamond drill cores show beds of greenstone down to half an inch in thickness. The thin beds are probably always tuffs. Structure: Rock structure in the Soudan area is complex, and because there are no recognizable horizons within the greenstone it is extremely difficult to work out the details. Generally speaking, the major regional structure is an anticlinorium, the axis trending east-west, with a westerly pitch. The Soudan mine is related to a synclinal structure on the north limb of the anticline about a mile from the west nose of the folded iron formation. The general structure at the mine is that of a closely folded minor syncline on the major regional anticline. A cross fault has dropped the east side so that the bottom of the syncline has not been reached, whereas to the west it is well shown by the mine openings and diamond drill exploration. Throughout the mine the beds of jasper, and ore-bodies that have replaced the jasper, normally dip northward at angles of 80" or steeper. In detail the jasper beds are extremely folded, probably as a result of deformation while they were still relatively unconsolidated. Orebodies: Ore in the Soudan mine is mainly a hard, dense, bluish hematite. Locally ore has been brecciated and cemented by quartz. The vugs commonly occurring near the borders of orebodies are lined with quartz crystals. They seem to have formed as part of the ore-forming process and are evidence that no folding or compression of the ore has taken place. The orebodies are numerous, varying greatly in size. Many lenses of high grade hematite are too small to be mined. Some of the larger orebodies have been followed vertically for as much as 2500 ft and horizontally up to 1500 ft. The large ore-bodies are extremely irregular in outline in the plane of the beds of jaspilite. In width they are more regular, as they are strictly governed by the width of the jaspilite beds and the greenstone wall rock, which seems to have resisted replacement by hematite. At many places the orebodies replace the jaspilite completely and have a footwall and hanging wall of greenstone. At other places either one or both walls may be jaspilite. Geologists who have studied the orebodies in recent years agree that evidence for the replacement origin of the hematite bodies seems conclusive. AS noted above, many of the orebodies replace jaspilite beds from wall to wall with no evidence whatever of compaction. The replacement origin is also supported by details of the banding which is characteristic of the

Jan 1, 1956

By K. F. G. Hosking

I read Professor Gaudin&apos;s paper with great interest and pleasure because for some time I have held that the chemical aspect of comminution is a subject of considerable importance to the mineral dresser and deserves to be thoroughly investigated. It does seem appropriate, however, to emphasize the fact that "fresh" edges and corners produced by the grinding of solids display enhanced reactivity has been recognized and utilized in the development of certain mineral identification techniques. Some of these techniques are worth noting, not only because they might facilitate research in the aspect of mineral dressing under discussion, but also because they emphasize the fact that many mineral species commonly regarded as being very inert can display a surprising reactivity when in the freshly ground state. In 1951 Isakov6 published a number of tests for the components of certain mineral species which depend essentially on grinding in a mortar a mixture of the material under investigation with a solid reagent. Thus when stibnite, 4(Sb2S3), is ground with sodium or potassium hydroxide. the antimony is revealed by a momentary development of a yellow color which changes in air to orange-red. Other antimony minerals need a preliminary treatment before the test can be carried out. This consists of grinding with aluminium sulfate, ferric sulfate or potassium bisulfate, and breathing upon the resultant mixture. I have employed a similar technique to determine the approximate magnesia content of certain limestones.&apos; The method depends essentially on the fact that when a sample of limestone is ground under controlled conditions with solutions of sodium hydroxide and Titan yellow the color of the final product is, within limits, a function of the amount of magnesia present. I have also shown that the components of a wide range of minerals can be identified by applying chemicals to their streaks on portions of vitrified, unglazed floor tiles, etc. Under such circumstances the diversity of the reactions which take place in the cold (because of the reactivity of fresh corners and edges) is surprising. Thus, for example, if a garnierite, (Ni,Mg)3Si2O5(OH)1, streak is treated first with a drop of 0.880 ammonia and then with a drop of a 1 pct alcoholic dimethyl-glyoxime it immediately becomes red, indicating the presence of nickel.&apos; Stevens and Carron9 have evolved a simple field test for distinguishing minerals by "abrasion pH." A soft nonabsorbent mineral is scratched in a drop of water on a streak plate until a milky suspension is formed. A piece of pH indicator paper is dipped into the suspension, after which it is removed and the maximum deviation from neutrality noted. When a hard mineral or one which absorbs water is being tested, fragments are first ground for 1 min with a few drops of water in a mortar to make a heavy suspension. The importance of the findings of such tests to mineral dressing may be judged by the abrasion pH values, Table 11, recorded by Stevens and Carron for certain species usually regarded as comparatively inert. The combined results Of the above researches clearly indicate that comminution is capable of altering the pH of a pulp and of causing the chemical nature of the surfaces of some of the components to be profoundly changed&apos; Depending On circumstances such surface alterations may have a beneficial or an adverse effect if these products are subsequently subjected to flotation. The tests also suggest that by grinding "inert" minerals with appropriate solid or liquid reagents "reactive" surfaces may be developed which might facilitate separations by flotation. It is an interesting and instructive problem to determine the reactions that are likely to take place when dry solid substances are subjected to comminution and to the unavoidable heat liberated during the process. To do this it is theoretically necessary to know the free energy values of the reactants and possible resultants, but unfortunately there is a dearth of such data! However, the heats of formation of many substances are known, and generally speaking, if in a reaction of the type AB + CD = AD + CB the sum of the heats of formation of AB and CD is less than that of AD and CB the reaction will probably proceed to the right. Thus, according to a note I have (the author of which I cannot name) if PbS (black) is warmed with CdSO, (white), PbSO., (white) and CdS (yellow) are formed, and that the reaction does, in fact, take place is indicated by the change in color of the mixture. The reaction is expected, as the sum of the heats of formation of PbS and CdSO, is less than that of PbSO, and CdS (as shown below). PbS + CdSO4 = PbSO4 + CdS 22.2 + 218.0 < 216.2 + 33.9 Finally, certain other aspects of the chemistry of comminution, which are neither mentioned by Professor Gaudin nor referred to by me are to be found in a paper by Welsh" and in the printed discussion thereof. A. M. Gaudin (author&apos;s reply)—The observations contributed by Dr. Hosking are indeed welcome, as they add to our experimental knowledge of a topic which is believed to be of the first importance. In connection with the experiments cited it should be kept in mind that oxidation, hydration, and carbonation at various rates should always be deemed to be possibilities when grinding is done in water or in air, even in "industrially dry" air. Special precautions might lead to sufficient minimizing of these reactions and to the assertion, instead, of deliberately-created reactions. The author wishes to thank Dr. Hosking for his contribution.

Jan 1, 1957

By C. Altstetter

THE work herein reported is restricted to the carbides which occur in quenched and tempered AISI 43XX steels with carbon contents up to 0.40 pct and silicon additions of up to 3 pct. In view of the instability and extremely small size of the carbides formed at low tempering temperatures, the technique for successfully preparing specimens for X-ray diffraction will be outlined. The alloys listed in Table I were obtained through the courtesy of the United States Steel Corp. in the form of 1/2-in. rounds forged from 100 lb. induction furnace heats (except for 4337 which was a commercial heat). The stock was normalized and then swaged and drawn to 15 mil wire with anneals at 1200F between passes. The wire was austenitized for 45 min in evacuated vycor capsules and quenched into iced brine with simultaneous smashing of the capsule. Tempering was done in air with a water quench after tempering. The carbides were extracted in a simple cell using a solution of 1M KC1 and 0.5 pct citric acid with an initial current density of 0.1 amp per sq cm. One end of a short length of wire was immersed in the solution, and the current at constant voltage was noted as a function of time. After about an hour the current dropped sharply because of the decrease in specimen cross-section. At this point it was found that the dissolution could be stopped and that the very fine wire which then resulted was just large enough to permit handling of the extracted precipitate still clinging to it, yet so small that it diffracted and absorbed only a negligible amount of the X-radiation. This rod of residue with a convenient handle of undissolved wire was rinsed in distilled water. alcohol, and acetone. Then it was dipped in a thin solution of cellulose-acetate cement and dried in vacuum. The resulting specimen was straight, uniform in density, easily handled, but most important, was completely sealed and never exposed to air. Furthermore, the residue had never been subjected to strong acids or rough handling such as in the extraction-replica technique or in the complete extraction to a powdered residue. It was found that improperly coated specimens were pyrophoric, turning to oxide with a dull red glow as they were exposed to air and yielding patterns of Fe2O3 and Fe3O4. The steels containing 3 pct Si were especially difficult to prepare for this reason. The specimens were put in a 57 mm Straumanis camera with double pinholes or slits and irradiated with filtered-chromium radiation. Readable patterns were obtained in less than an hour. A preliminary finding of some note was that for both tempered and as-quenched specimens of steels 4337 and 4337 (1.5 Si). M23C6 patterns were found along with the patterns of other constituents of the residues. This result was somewhat surprising in that previous investigators had reported that this carbide did not appear in a 0.38 pct C, 0.48 pct Mo steel1 or in chromium steels of less than about 10 pct Cr.2 Although the total amount of carbide-forming alloying elements is less than 2 pct, due to their mutual interaction and the action of the plastic deformation in promoting equilibrium, this carbide was able to form even in the steel containing 1.5 pct Si. M23C6 was not detected in the 4337 (3.0 Si) steel and the lower-carbon steels were not investigated in this condition. It is very likely then that the steels studied herein underwent a fourth stage of tempering during the anneals at 1200°F. This result has significance in that even a small amount of undissolved M23C6 in a low-carbon, low-alloy steel would exert a large effect on its hardenability. Its presence would also influence the mechanical properties by decreasing the carbon content of the matrix. Annealing in vacuum for 1 to 4 hr in the austenite field removed all traces of MZ3C+ The results on carbide precipitation during tempering, summarized in Table I, are in agreement with those of Klingler et al.3 for the higher carbon steels. For the AISI 4337 steels it is noteworthy that in the steels with added silicon the E carbide persists to longer times and higher temperatures and that silicon delays the formation of cementite. The results for the lowzr-carbon steels parallel those of the higher-carbon grade. The appearance of E carbide in the AISI 4315 is significant. There is considerable disagreem-nt in the literature as to whether this carbide forms in the tempering of steels containing less than about 0.2 pct C. Following the detection of E carbide in a 0.18 pct C plain-carbon steel,4 its occurrence in a steel containing chromium and molybdenum should be expected. The fact that the low-carbon steels have the same carbide-precipitation sequence as the high-carbon steels has bearing on the larger problem of the exact tempering reactions in all steels. Following the suggestion of Roberts et al.,&apos; the first stage has been generally assumed to result in a metastable equilibrium of c carbide and martensite of about 0.25 pct C. From this it was concluded that a steel having less than 0.25 pct C should then be under-saturated with respect to c carbide and should not precipitate this carbide upon tempering. In view of the experimental findings of c carbide in steels hav-

Jan 1, 1962

By E. J. Eisenach, W. E. Jones

SAFETY and industrial hygiene have always been recognized as highly important in company policy, and the co-operative support of the company officials and entire plant personnel has contributed largely to the present success of the Company&apos;s program in this field. Growth has necessarily been slow, and dependent, at times, on trial and error but the program in its present form combines the regulations, working methods, and equipment that have proved their value under actual operating conditions. Every effort is made to keep the program on a practical basis. Continuous experimental work is carried on in conjunction with the health and safety program, with resultant periodic changes for improvement. As a proof of accomplishment, in 1945 the frequency and severity rates for accidents were the lowest in the history of the operation. A full-time safety engineer was employed in 1933 and an assistant safety engineer in 1936. During the following year a stenographer was employed in the office and a safety inspector was added for the mine. During the gradual expansion of operations that was climaxed by

Jan 1, 1946

By C. S. Sivaramakrishnan, Manjit Singh, Rajendra Kumar

Regarding liquid nzetals structurally as a suspm-sion of clusters , having derivated solid-state coordination, in truly liquid atoms, the recently developed Kuvlar-Samarin technique of centrifuging- in liquid state enabled the determination of the cluster sizes inAl-Cu mid Pb-Sn systems. It is shown that the colutne fraction of the clusters does not exceed 9 pct and the energy of their formation in Al-Cu is about 5.5 kcal per g-atom and in Pb-Sn eutectic alloys about 25 kcal per y-atoni. STRUCTURAL investigations of liquid state have principally followed the following three courses: i) studies with X-ray, electron, or neutron diffraction; these investigations have shown that there is a certain amount of regularity in the structure of liquid metals which can be defined by a coordination number and that the structure is a derived function of that in the solid state; ii) thermodynamical investigations which are based on the concept of ideal behavior; these describe the liquid state in terms of free-energy values and other thermodynamic functions; although these investigations are of help in the study of the general effects of alloying, they do not provide any structural insight into the precise atomic distribution in liquid state; iii) measurements of surface tension and viscosity; although it is natural to expect that the viscosity is related to the structure in liquid state, these investigations have so far only provided information which can be used by the foundry technologists and has been little utilized in formulating models of the structure of liquid state. As it happens, investigators in the three groups have worked almost independently of each other and there is practically no structural correlation between the results of one group with those of another. The purpose of the present paper is to indicate that the experimentally measured parameters of these three groups of research are closely related to the structure in the liquid state. STRUCTURE OF LIQUID METALS Although atomic distribution in solid and gaseous states is rigorously known, that of the liquid state is only appreciated on the fringes. There is no universal model of atomic distribution in liquid state, but two diverse models are at present hotly contested. The first, largely expounded by ~ildebrand,&apos; regards the liquids as condensed gas since many of their properties and much of their behavior can be adequately described by regarding them as fluids. The second mode12j3 considers that some form of near-solid as- sociation of large number of atoms exists in the liquid state. On the other hand, ~ernal&apos; was able to predict rather precisely the radial distribution functions in liquids on the basis of statistical geometric approach which considered that liquids are "homogeneous, coherent, and essentially irregular assemblage of molecules containing no crystalline regions or holes large enough to admit another molecule". He introduced the concept of pseudonuclei in the otherwise random structure as aggregates of closely packed tetrahedra which gradually merge into irregularity and continually replace each other. To what extent the pseudonuclei can be regarded as regions of near-solid association is indefinite but Bernal suggested that the concept of pseudonuclei can be compromised with the latter model if the near-solid associations are regarded as extremely dense and not necessarily crystalline. The difficulty in projecting the structure of liquid metals arises because they exhibit duplicity of character as some of their properties are closer to those of crystalline solids and others to fluids. There is an increasing tendency to discuss the structure of liquid metals in terms of the second concept according to which the structure of liquid metals may be conceived as consisting of i) clusters of atoms where the aggregation is a close derivative of that in the crystalline state, ii) individual atoms which behave like true liquids in respect to degrees of freedom and iii) excess number of vacancies. It is noteworthy that the introduction of only 5 pct vacancies is sufficient to transform crystalline matter into the liquid state. At any instant of time thermodynamic equilibrium exists between i, ii, and iii, but the relative proportion of the clusters and random atoms is not known. That this is so can be appreciated by the fact that, when liquid metal is rapidly cooled, liquid state vacancies may condense in the form of dislocation loops and vacancies in excess of their equilibrium number in solid state. These dislocation loops have been observed in thin foils of aluminum prepared from rapid cooled aluminum. As temperature increases above melting point the number and volume fraction of clusters decrease but those of vacancies and random atoms increase. Clusters are transient in nature. In pure metals the cluster is an aggregation of the metal itself. In alloys, however, the nature of the cluster largely depends on the interaction between solvent and solute atoms. If the interaction between unlike atoms is greater than between like atoms: the clusters are then aggregates of unlike atoms. Examples of this kind of system are A1-Cu, Mg-Pb, and so forth, i.e., systems which exhibit negative departures from the Raoult&apos;s law. In systems where the interaction between unlike atoms is smaller than be-

Jan 1, 1968

By W. A. Backofen, D. H. Avery, G. A. Miller

An evaluation has been made of the relative importance of yield strength (?) and stacking-fault energy (y) to the rate of fatigue-crack growth in materials of fcc structure. Pure copper and its solid-solution al-loys with aluminum and nickel were chosen for the study because they provided sufficient range in both quantities of interest that either could be varied independently of the other. Experiments involved alternating tension and compression of flat specimens which were prepared with sharpened internal notches so that most, if not all, of the crack-nucleation interval could be eliminated. Growth rate (dC/dN) was concluded to be proportional to the square of the plastic-strain amplitude (€,,) over a strain range of approximately 6x 10-4 to 6 x 10-3. The factor, k, linking dC/dN and ep in dC/dN = kEp2 increased and decreased with corresponding variations in y, but it did not respond syste?>/atically to change in ay, indicating that y is the significant variable in crack growth at constant plastic-strain amplitude. In polycrystalline material, k varied by a factor of 5 over the available range of y. In a few single-crystal experiments on Cu-A1 alloys the growth rate responded less strongly to change in y. It has been suggested that single crystals behave somewhat differently than poly crystalline material because there is more extetnsive substructure near the grain boundaries in the latter, and this facilitates crack advance by separation along subgrain boundaries. A point of some controversy in current work on fatigue relates to the effects of strength and stacking-fault energy on crack growth. In recent experiments a separation was made between the cycling intervals for crack nucleation and the subsequent growth that eventually ends a specimen&apos;s fatigue life.&apos; The study was carried out on Cu-A1 alloys primarily, fatigued in alternating four-point bending to constant deflection. A nucleation interval of about 10&apos; cycles (at a total strain amplitude = 0.2 pct) was found to be insensitive to aluminum content in the range 0 to 7.5 wt pct, while the growth period was increased approximately forty fold over the same compositional range. The increase was not in any sense linear, however. Rather, most of the change occurred below 4 pct A1 or a stacking-fault energy, ?, of about 15 ergs per sq cm. It was argued that the plastic-strain amplitude was approximately constant, and therefore the effect of composition must have grown out of the reduction in stacking-fault energy. Several studies have shown that, with high ?, cross slip is encouraged, subgrain structure is introduced during fatigue, and cracking is aided through propagation along subgrain boundaries.1-5 Therefore, lowering ? sufficiently to interfere with substructure formation would be expected to retard growth rate. On the other hand, it is a general rule that resistance to fatigue cracking increases as strength is raised. Accordingly, there might still have been some doubt that Y was the controlling variable, since strength would be increased as y was lowered by the aluminum additions. To help in dispelling that doubt, an experiment was made on a polycrystalline Cu-Ni alloy similar in strength to the Cu-A1 alloys but of higher ?; the crack-growth interval was found to be essentially that of pure copper.&apos; Further support for this position on stacking-fault energy as it relates to crack growth is derived from work by Boettner and McEvily,6 in which the actual crack-growth rate was measured on samples previously notched so as to minimize the nucleation period. Unfortunately, it was necessary in isolating strength level to compare different alloy systems and grain sizes. Recognizing the complication, it was still concluded that growth may be retarded by a reduction in y, per se. A related study has also been made by Roberson and Grosskreutz.7 The zinc content of a brass was systematically changed to alter strength and stack-ing-fault energy, although not below the 15 ergs per sq cm at which pronounced change in growth interval was found in the earlier work. The results were limited to more or less conventional S-N diagrams so that nucleation and growth events could not be separated. No definite conclusions were drawn, but

Jan 1, 1967

By S. A. Falconer

D. A. Dahlstrom—Mr. Falconer has done an admirable job of proving the adaptability of the cyclone to the beneficiation of a very difficult size range in the preparation of coal. The addition of the cyclone to other coarser size methods makes it economically feasible for the coal operator to rigorously control his marketed products at a high and uniform quality level down to the 48 and 100-mesh size. Furthermore, it should be pointed out that by utilizing the cyclone as a deslimer or classifier the —3 200-mesh fraction, usually containing large percentages of undesirable material, can also be quickly and cheaply removed from the clean coal. Advantages of such a step are several: (1) Reduction of ash content, especially where clays and slimes are serious. (2) lower moisture content of the final coal. (3) easier mechanical and thermal de-watering of the fine coal due to higher cake and bed permeabilities. The author has indicated that adjustable control means should be installed on the cyclone operating on a heavy-media slurry. This also holds true for the cyclone acting as classifier, deslimer or preliminary dewatering agent and is worthy of special emphasis. Such controls, while not necessarily automatic, must be simple, rapidly adjustable, and require a minimum of attention. Three methods available to the operator are (1) throttling valve on the feed line, (2) back pressure valve on the overflow, and (3) adjustable diameter underflow nozzles. The first two, while fulfilling the specifications, suffer the disadvantage of restricting capacity if severe throttling is necessary. The third method has little effect on capacity and easily maintains an underflow of correct moisture content. Several designs are possible, but two find the widest application. The first was developed by Robert Piros of The Truax-Traer Coal Co. and uses a simple casting containing two holders for underflow nozzles which can be rotated about an axis parallel to the cyclone centerline. These holders retain the underflow nozzle flush with the conical section walls. When a change in nozzle diameter is required, the new size is placed in the spare holder and rotated into place. A second design utilizes a soft rubber cylindrical tube which is compressed or released from three sides, causing the inner diameter of the tube to decrease or increase. This is achieved by using a machine-threaded,

Jan 1, 1951

By S. A. Falconer

D. A. Dahlstrom—Mr. Falconer has done an admirable job of proving the adaptability of the cyclone to the beneficiation of a very difficult size range in the preparation of coal. The addition of the cyclone to other coarser size methods makes it economically feasible for the coal operator to rigorously control his marketed products at a high and uniform quality level down to the 48 and 100-mesh size. Furthermore, it should be pointed out that by utilizing the cyclone as a deslimer or classifier the —3 200-mesh fraction, usually containing large percentages of undesirable material, can also be quickly and cheaply removed from the clean coal. Advantages of such a step are several: (1) Reduction of ash content, especially where clays and slimes are serious. (2) lower moisture content of the final coal. (3) easier mechanical and thermal de-watering of the fine coal due to higher cake and bed permeabilities. The author has indicated that adjustable control means should be installed on the cyclone operating on a heavy-media slurry. This also holds true for the cyclone acting as classifier, deslimer or preliminary dewatering agent and is worthy of special emphasis. Such controls, while not necessarily automatic, must be simple, rapidly adjustable, and require a minimum of attention. Three methods available to the operator are (1) throttling valve on the feed line, (2) back pressure valve on the overflow, and (3) adjustable diameter underflow nozzles. The first two, while fulfilling the specifications, suffer the disadvantage of restricting capacity if severe throttling is necessary. The third method has little effect on capacity and easily maintains an underflow of correct moisture content. Several designs are possible, but two find the widest application. The first was developed by Robert Piros of The Truax-Traer Coal Co. and uses a simple casting containing two holders for underflow nozzles which can be rotated about an axis parallel to the cyclone centerline. These holders retain the underflow nozzle flush with the conical section walls. When a change in nozzle diameter is required, the new size is placed in the spare holder and rotated into place. A second design utilizes a soft rubber cylindrical tube which is compressed or released from three sides, causing the inner diameter of the tube to decrease or increase. This is achieved by using a machine-threaded,

Jan 1, 1951

By Henry D. Hibbard

THIS article aims to clarify the use of some terms often occurring in writings on iron and -steel, and also to suggest several new short abbreviated names for some of the things related to the subject which now are indicated by phrases. Crude or Crude Iron The name crude or crude iron is recommended for the iron produced from ore by the blast furnace. When necessary it can be specified as pig iron when in the form of pigs (usually cold), or as molten iron, commonly called hot metal to distinguish it from cold iron in pigs. The product of a direct process of making wrought or malleable iron from ore is not included.

Jan 1, 1924

By Daniel R. Shawe

Large tabular beryllium deposits in waterlaid rhyolitic tuff at Spor Mountain, Utah, contain the world's largest known resources of beryllium (as bertrandite). The district also has produced fluorspar and uranium. The largest beryllium deposit is about 2.5 miles long, and known deposits contain many million tons of material with at least 0.5 per cent BeO. The beryllium-bearing tuff (Pliocene?) underlies topaz-bearing rhyolite ( Pliocene?) that contains unusually high amounts of beryllium, fluorine, and uranium, and overlies other volcanic rocks (Pliocene? or Micocene?) and marine carbonate and elastic rocks ( Paleozoic). The deposits occur in hydrothermally altered tuff only where it contains abundant carbonate pebbles eroded from the Paleozoic rocks and where the tuff was deposited as thick layers in now-buried paleovalleys. Basin and Range faults, thrust fa ults, and possibly strike-slip faults formed in this part of the Basin and Range province during the late Tertiary, and volcanic rocks were extruded. Beryllium mineralization probably occurred during this episode. Undoubtedly the beryllium deposits are related genetically to the topaz-bearing rhyolite, but the details of their genesis are not certain and probably are complex. Beryllium deposits are close to major faults, and locally the beryllium is concentrated at faults, indicating fault control of mineralization. Some elements in the deposits, such as lithium, however, are evenly distributed in certain Luff beds and perhaps were introduced prior to faulting. Still other elements, such as manganese and lead, were concentrated in the beryllium deposits and subsequently were leached along late fractures, indicating a period of metal redistribution following mineralization.

Jan 1, 1968

By C. E. Tsoutrelis

A new method for determining rock drillability in diamond drilling is discussed; the method takes into consideration both penetration rate and bit wear. The method is based on drilling a rock specimen under controlled laboratory conditions using a model bit. The technique used for determining the experimental variables is extremely simple, quick, and reliable. Drillability is then determined by the mathematics of drilling. In considering the different factors that affect diamond drilling performance, the nature of the rock to be drilled is of outmost importance since it affects significantly the drilling costs and such other variables as bit type and design, drilling thrust, and bit rotary speed. Many attempts have been made to study this effect by correlating actual drilling performances either to certain physical properties of the rock being drilled1-? or to test drilling data obtained under laboratory conditions.7-13 These attempts were aimed at providing a reliable method of predicting by simple means the expected rock behavior in actual drilling, thus giving the engineer a tool to use in estimating drilling performances and costs in different types of rock. The purpose of this paper is to describe such a method by which rock drillability (a term used in the technical literature to describe rock behavior in drilling) could be determined in diamond drilling. It is believed that the proposed simple and reliable method will cover the need of the mining industry for a workable method of measuring the drillability of rocks. It should be emphasized, however, that since drill-ability depends on the physical properties of rock and each drilling process (diamond, percussive, rotary) is affected by different or partly different rock properties,14-l6 the proposed method of determining rock drillability cannot be extended to the other drilling processes. The results presented in this paper form part of an extensive three-year research program carried out by the author in the laboratories of the Greek Institute of Geology and Subsurface Research. During this period the effects of the physical properties of rocks and of such operational variables as drilling thrust and bit rotary speed in diamond drilling were investigated in detail. DRILLABILITY CONCEPT The literature is not devoid of drillability studies. While there are a number of investigators1,3,5-7,9-0,12-13,17 who have attempted to establish by direct methods (i.e., drilling tests under laboratory conditions) or indirect (i.e., through a physical property of rock) an index from which the drilling performance in a given rock may be estimated, very few6-7,9,12, of the proposed methods seem to be of much practical value to the diamond drilling engineer and none to date has been universally accepted. Commenting on the proposed methods for assessing rock drillability, Fish14 remarks that "for a measure of drillability to be accepted it is essential that penetration rate at a given thrust and bit life are elucidated as otherwise the method is of little value." This statement should be examined in more detail by making use of the penetration rate-drilling time diagram obtained in drilling a rock under constant operational conditions. Furthermore, the merits of using this diagram to describe rock drillability will be pointed out. At the same time reference will be made to this diagram when discussing some previously proposed methods. Fig. 1 illustrates such a diagram for three rocks,A, B, and C, which have been diamond drilled under identical conditions. It is assumed here that rocks A and B have the same initial penetration rate, i.e., VOA = Vog, but since rock B is more abrasive than A, rapid bit wear occurs and as a result the fall of its penetration rate with respect to time is more vigorous than in rock A. This is shown graphically by a steeper V = f(t) (0 curve in this rock than in rock A. Rock C has a lower initial penetration rate, due to higher strength properties16 but since it is not very abrasive, only a slight fall of its penetration rate occurs during drilling (in this category are some limestone and marbles with compressive strength above 1000 kg per sq cm). It follows from the foregoing considerations that the characteristic for each rock curve (I) is a function of (i), the penetration rate of the rock Vo recorded at the instant of commencing drilling, which determines the starting point of the curve (1) on the y-axis and (ii), the abrasive rock properties which determine the rate of fall of Vo with respect to time. Thus, curve (I) provides an actual picture of the rock behavior in drilling for given operational conditions, and it can be used with complete satisfaction to assess rock drillability. It can be seen clearly from Fig. I that proposed methods for assessing rock drillability by measuring the

Jan 1, 1970

By Brian R. Castle, James J. Scott

INTRODUCTION Referring to a ground support system as a &apos;band-aid&apos; borders on getting cute, but the application of cable slings in U.S. mining is somewhat analogous. Where problems in the roof or rib require additional support, the versatile cable sling is the answer in a variety of conditions. To fully understand how and why cable slings are used today we must briefly review their development history. Much of the thrust over the last five to seven years in ground support fixtures has been the development of hybrid systems. Taking the best of two or more existing roof bolt fixtures and marrying them into a new fixture which exhibits the good characteristics without the bad of the parent systems. Resin point anchored mechanical bolts, continuous threaded rebar bolts, and others have all be- come important fixtures in rock mass stabilization. HYBRID GROUND SUPPORT SYSTEM The cable sling system is also a hybrid, both in its parentage and in its ground support characteristics. See figure 1. Cable slings combine the techniques of cement. grouting high-strength cables, Friction Rock Stabilizers, and truss-like suspension into a versatile and high- strength ground support system. 1/2" high-strength cable is cement grouted in place in a manner similar to pre-

Jan 1, 1983