Search Documents

By L. F. Pease, J. H. Brophy

A phase diagram for the Ta-Zr system is presented. The system is of the minimum-melting point type with the 0-zirconium phase decomposing monotectoidally at 785°C and 95.5 at. pct Zr. The minimum solidus temperature is 1875°C and the temperature of the top of the monotectoid loop is 1775°C. Techniques employed included X-ray diffraction and fluorescmce, electron microprobe analyses, diffusion couples, metallography, and melting-point measurements. Errors due to interstitial solutes and in melting observations are particularly common in this system, and their occurrence is discussed. SEVERAL versions of the Ta-Zr phase diagram have been reported in the literature.lm7 Williams et al.' report a diagram of the minimum-melting point type with a monotectoid reaction at 800°C and 12 wt pct Ta. The minimum in the solidus occurs at 1820°C and 25 wt pct Ta, while the top of the monotectoid gap is located at 1780°C and 80 wt pct Ta. The experimental techniques employed were metallography, electrical resistance variation with temperature, dilatometry, X-ray diffraction, and direct observation of melting by the technique of Pirani and ~lterthum.' Experience in the Nb-Zr phase diagram has shown that small changes in the interstitial content can cause large shifts in the positions of the phase boundaries. Small amounts of inter -stitials can cause similar changes in the Ta-Zr system and may be responsible for the wide variations in the phase diagrams previously reported.'-' The authors15 have found that alloys containing 0.75 wt pct 0 and 1.0 wt pct Ni with tantalum contents from 19 to 85 at. pct often contain a lamellar or cellular precipitate after annealing above 1400°C. This precipitate is very similar to that reported by pollack,12 Ralls," and Donlevy17 for the Ni-Zr system. In the present investigation, a wider variety of experimental techniques and improved alloy purity were applied to the resolution of errors in diagrams for this system as they now appear in the literature. New results have been obtained in the areas of alloy homogeneity and purity. Errors in the common techniques of direct melting observation in binary alloys have been demonstrated. In the commercially important high-tantalum region, the more accurate metallographic method of solidus determination has been employed. EXPERIMENTAL PROCEDURE Nominal analyses of the materials employed are given in Table I. The zirconium was low hafnium reactor grade iodide crystal bar, and the tantalum was in the form of high-purity sheet. Powders were impossible to use because of gas content. Alloys were melted on a water-cooled copper hearth, with a thoriated tungsten-tipped nonconsumable electrode in 2/3 atm of Zr "gettered" argon. Alloys were

Jan 1, 1963

With a total value to date of well over $200,000.000.00 for its ore production, the Tintic mining district, which is about 100 miles southwest of Salt Lake City, ranks as one of the three main ore producing areas of Utah. In it are located the biggest silver mines of the country, silver having been the chief metal produced in the camp since its start. Tintic's silver production to date has a total value of over $1 00,000,000, approximately half of the value of the camp's ore production, the balance being roughly divided among lead, gold and copper. Discovery of the camp was made in the late sixties. Lack of transportation and ore reduction facilities delayed extensive development of the area for nearly a decade. In recent years Tintic's ore production has ranged from 350,000 to 400,000 tons annually. In 1924 the camp produced one-eighth of the silver produced in the nation with an output of 7,729,700 ounces. Its lead production was 77,765,000 pounds and its gold production 26,285 ounces.

Jan 1, 1925

THE shipments of high-grade manganese ore, con-taining 35 per cent or more of manganese, from the mines in the United States in 1926 were slightly less than half as large as similar shipments in 1925, accord-ing to the United States Bureau of Mines, Department of Commerce. The shipments in 1926 by 45 producers amounted to 46,258 long tons as compared with 98,324 long tons by 42 producers in 1925. This decrease was due to the falling off of the shipments from Montana. The domestic production of metallurgical ore in 1926 was 26,530 tons; that of chemical ore, 19,728 tons. Montana was the largest shipper with 5713 tons of metallurgical ore and 17,904 tons of chemical ore. The largest individual shipper of metallurgical ore was the Crescent Mine in the Olympic Mountain Region, Clallam Co., Washington, from which the shipments for the year were 3162 tons. The mine was operated by lessees and reverted to the owners in July, and thereafter to the close of the year no .ore was shipped.

Jan 6, 1927

By William E. Ford, Edward Salisbury Dana

URANINITE. Cleveite. Broggerite. Nivenite. Pitchblende. Isometric. In octahedrons (o), also with dodecahedra1 faces (d) ; less often in cubes with o and d. Crystals rare. Usually massive and botryoidal; also in grains; structure sometimes columnar, or curved lamellar. Fracture conchoidal to uneven. Brittle. H. = 5'5. G. = 9'0 to 9'7 of crystals; of massive altered forms from 6'4 upwards. Luster submetallic, to greasy or pitch-like, and dull. Color grayish, greenish, brownish, velvet- black. Streak brownish black, grayish, olive-green, a little shining. Opaque. Comp. -A uranate of uranyl, lead, usually thorium (or zirconium), often the metals of the lanthanum and yttrium groups; also containing the gases nitrogen, helium and argon, in varying amounts up to 2'6 p. c. Calcium and water (essential?) are present in small quantities; iron also, but only as an impurity. The relation between the bases varies widely and no definite for- mula can be given. Radium was first discovered in this mineral and it has been shown that it and the helium present are products of the breaking down of the uranium.

Jan 1, 1922

By A. G. Allten

EXAMINATION by metallographic and X-ray diffraction means of an austenitic steel containing 0.06 pct C, 1.26 pct Mn, 0.38 pct Si, 21.15 pct Ni, 18.72 pct Cr, 3.07 pet W, and 9.14 pet Mo indicated that a - phase, which had not been reported in the literature, existed in this steel. Both the s and car-bides of the M6 C type were present in the as-forged steel. The carbides dissolved completely in the aus-tenite at approximately 2200°F (1205°C). The s, however, was present at all temperatures up to the solidus temperature of the steel at approximately 2375°F (1300°C). Ferrite was not found in any condition of the steel. The faintness of some of the s lines in X-ray patterns obtained from samples of the steel made it desirable to isolate the s prior to verification of its entire pattern. It was found that the s phase could be separated from samples of the steel which had been water quenched from 2250°F (1230°C) by dis-

Jan 1, 1955

By Cyril Wells, Paul E. Busby, Donald P. Hart

EARLY workers in the field have established that the diffusion of nitrogen follows normal diffusion laws. Concentration-penetration data from layer analyses of reasonably pure iron specimens nitrided in an atmosphere of CO-NH, are given in the literature,' and were utilized to calculate diffusion constants for nitrogen. The diffusion of nitrogen in y-iron may be represented approximately by the equation D - 1.07x10-' e-:".'m'"'r The diflusion coefficients, D, given by this relation represent mean values, since carburization occurred simultaneously with nitriding. The rate of diffusion in a-iron has been determined from calculations based on data obtained by measuring the internal friction of samples at each of several frequencies and temperatures.' The expression for the diffusion of nitrogen in a-iron derived from these experiments is D= 1.4x10-1 e-it tudent Increasing carbon content decreases the diffusion of nitrogen in a-iron.3 Oxygen, either dissolved or combined, has been shown' to exert a marked influence on the diffusion of nitrogen from a nitriding atmosphere. D values increase rapidly with increasing amount of dissolved oxide in the metal, but diffusion is completely inhibited if preliminary oxidation has produced the slightest trace of iron oxide on the surface. Diffusion coefficients have also been calculated from permeability and solubility data,' but these values are of questionable accuracy since the boundary conditions assumed may not actually exist. Experimental Method The method selected for determining the diffusion coefficient of nitrogen in a-iron in the present investigation was the so-called fractional saturation method. This method consists of heating the specimen in an atmosphere of H2-NH8 mixtures of known composition for a predetermined time. Following this treatment, the specimen is analyzed for nitrogen; and the diffusion coefficient is calculated from a known relationship of the fractional saturation, time of diffusion, and dimensions of the specimen. This relation is based on a solution of Fick's second law and assumes that the surface of the specimen immediately reaches a given concentration which remains constant during the diffusion anneal. Tabular solutions are available4-5 and provide the relationship between fractional saturation and the quantity \/Dt /a, where D is the diffusion coefficient in cm2 per sec, t is the time of the diffusion anneal in seconds, and a, in the present experiments, is the half-thickness of the slab specimen in cm. The method is adequately discussed elsewhere.9-10 Material The material for this study consisted of 3/32 in. thick (0.24 cm) carbonyl iron plate. The major impurities in this iron are oxygen and carbon, which are readily removed by long time high temperature treatment in an atmosphere of purified hydrogen. In order to reduce the diffusion anneal time for saturation runs, some of this material was rolled to a thickness of 0.015 in. (0.038 cm) prior to the hydrogen treatment. Hydrogen treatments were carried out in a hydrogen-purified Armco iron tube heated in a global

Jan 1, 1957

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel's surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By J. E. House, C. J. Lewis

In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-pregnant sulfuric acid leach solution is contacted with an organic extractant dispersed in kerosene; the uranium enters the organic phase and associates itself with the organic extractants. Simultaneously an-ions or cations, as the case may be, leave the organic extractant phase and enter the aqueous phase. The two phases are then allowed to separate by virtue of their immiscibility. Based on the data available, a generalized procedure for the recovery of molybdenum from the sodium carbonate scrub liquor of acid leach uranium mills using secondary and tertiary amine extractants is presented, as is another generalized procedure for the recovery of molybdenum from the bleed stream of alkaline leach uranium mill circuits. Such economic appraisal as can be made at this stage of the development is also indicated. Molybdenum occurs in most uranium ores. Whether the uranium is solubilized by the acid leach route or by the alkaline leach process, some of the molybdenum present in the ore is solubilized along with the uranium. Molybdenum in uranium mill pregant solutions may cause processing difficulties, among which may be mentioned the poisoning of resins, the precipitation of organo-molybdenum complexes, or the build-up of molybdenum in recycle streams. While the uranium milling industry has been successful in applying measures to overcome the problems arising from the presence of molybdenum in the circuits, such measures nevertheless add to the cost of producing uranium yellow cake concentrate. Table I shows the analysis of typical uranium pregnant leach solutions. Uranium recovery by solvent extraction is presently practiced only in conjunction with acid leach circuits, and it may be noted that of about 16,000 tons of uranium ore daily processed by sulfuric acid leach, more than half of this tonnage follows the solvent extraction route. Uranium mills leaching ore with sodium carbonate-sodium bicarbonate solution (the so-called alkaline leach circuit) do not use solvent extraction. In this case the uranium pregnant solution is sufficiently pure to permit the direct precipitation of uranium concentrate with subsequent recycle of the alkaline leach solution. While solvent extraction procedures may be developed which are economically attractive for the alkaline leach uranium process, this has so far not been the case. The earlier uranium mill solvent extraction circuits used organo-phosphate extraction reagents, among which di-2-ethylhexyl phosphoric acid was popular. It should be borne in mind that uranium in its sulfuric acid leach solution exists in an equilibrium involving uranium in both anion and cation forms: uo + 2S0 = [uo2(so4)2] For this reason uranium may be extracted by either cation extractors or anion extractors and this is likewise true of molybdenum. However, the organo-phosphate extractants also load ferric iron which is usually present in the uranium acid leach solution. For this reason, it is necessary to reduce this solution substantially to the ferrous state ahead of solvent extraction using organo-phosphate reagents. The amines, being anion extractors, selectively reject iron and thus render the iron reduction step unnecessary. In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-

Jan 1, 1961

By W. S. CAYPLESS, H. O. Hofman, E. E. HARRINGTON

1. INTRODUCTION. AT the Lake Superior meeting, September, 1904, Messrs. A. Gibb and R. C. Philp presented a paper entitled " The Constitution of Mattes Produced in Copper Smelting,)' in which they concluded that ferrous and cuprous sulphides formed the chemical compound, 5 Cu2S, fee. They arrived at this inference from the observed fact that a matte containing Cu2S, 90.4, and Fee, 9.6 per cent (or, in round figures, Cu2S, 90, and Fee, 10 per cent.), did not contain any metallic copper, while one with more than 10 per cent of FeS readily dissolved copper, and with less than this amount retained copper in mechanical suspension. Although they determined the melting-points of five mattes containing from 32.6 to 80.1 per cent of copper, they did not draw a freezing-point curve, as the necessary apparatus was not available. A microscopical examination of 11 polished samples, gave them a grayish-black field of very uniform appearance, except that 5 of the specimens showed the presence of metallic copper. The object of the present investigation was to supplement the above paper by drawing the freezing-point curve of the series ferrous sulphide cuprous sulphide, and to see how the constitution could be further, revealed by microscopical work. The results obtained lead to conclusions very different from those of Gibb and Philp. While their paper bears the date 1904, it was published only in 1906.2 In the meantime, Bolles3 had presented his paper, "The Concentration of Gold and Silver in Iron Bottoms." The raw material which formed the basis of the research was a matte containing Fe, 61.68, and Cu, 11.20

Jan 1, 1907

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Member, Graduate Colorado School of Mines. Four years' experience in West and Northwest. Two years with American Smelting and Refining Co. Wishes to join field party on geological work, mining or areal, where opportunity will be given to be of direct assistance to chief of party in solution of field problems. Age, 26. Unmarried. At liberty June 1. No. 342. Member, technical graduate, aged 30, with' 7 years' experience in concentrating and mining, desires a position of authority with reliable company. At present employed. No. 343. Member. Ambitious, energetic, tactful engineer, college graduate, married, aged 30, desires location with a large coal mining organization. Seven years with present employers -n middle west; has had broad experience in the past eight years on examination, development and construction; successful record in handling men. Position must carry responsible work and a future. Will go anywhere for proper opportunity. Exceptional references as to reliability, character and capacity for work. No. 344.

Jan 3, 1917

By Renato G. Bautista, David C. Lindholm

The results of scale-up studies on a continuous, multistage horizontal mixer-settler extractor are presented. The chemical and mechanical system involves the separation of lanthanum from a mixture of rare earth chlorides using di(2-ethylhexyl) phosphoric acid as the solvent and dilute HCl as a scrub solution in a bench scale extractor. Each stage has a hold-up of 2.6 l. A single stage unit is utilized for scale- up studies. Results are obtained on four sizes of geometrically similar units, the largest being six times the volume of the original bench size. A unit operations technique is chosen so that mixing and settling can be examined independently. Variables examined include type of continuous phase, flow rate of inlet streams, and power input to the mixer. Inlet flow-rate ratios are kept constant for all tests. TWO potential methods of unbaffled pump-mixer scale-up are explored; the maintenance of constant impeller tip speed and constant power input. For the settler, the previously successful method of basing design on constant flow-rate per unit cross- sectional area is used.

Jan 1, 1977

By R. J. Wensley

THE use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Some-times the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its, burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance.

Jan 9, 1921

By W. A. Forbes

OUR present-day geological surveys show that 36 of our States are underlain with bituminous coal, covering a total area of 496,709 square miles. The North American continent possesses 69 per cent of the world's coal reserves, with the United States alone having an estimated 55 per cent. The American coal reserves, in tons, are calculated to he about 3,500,000,000,000 tons, of which we have exhausted about 1 to 1 1/2 per cent. If this coal were mined at the rate of the 1918 production-a record output of 579;000,000 tons-it would not be depleted for 4,000 years. The more easily accessible and high-grade coals would obviously be consumed much before this; some estimates are 100 years. The natural progress of the nation's industries up to 1910 encouraged on every hand the development of new mines, especially where cheap and easy access to coal measures was coupled with short hauls to the consumer. Over-development resulted, which is perhaps today one of the fundamental causes for the many difficulties faced by the coal industry, which is highly competitive; about 70 per cent of the production cost is labor. Salient statistics for 1930, recently issued by the U. S. Bureau of Mines, follow:

Jan 1, 1932

By Samuel H. Dolbear

NOT WITHSTANDING the extremely low ebb of business activity, the nonmetallic industries have fared somewhat better than some other branches of mining. The average price level in nonmetallics, although far from satisfactory, has resisted any cataclysmic fall such as has been suffered by copper and other metals. Stocks, also, though too abundant, represent no corresponding overhang of the market, which should result, in some branches, in a more rapid recovery. Research work has continued in some industries with interesting developments.

Jan 1, 1933

By Paul F. Kerr, Donald M. Hausen

Fine colloidal gold near Carlin, Nevada is disseminated in leached carbonate strata of the Roberts Mountains Formation in the Lynn "window" of the Roberts Mountains thrust fault. The ore body is generally stratiform and is more or less conformable to altered beds near the top of the formation, underlying Devonian limestones. Two sequences of mineralization are recognized: ( 1) an earlier base metal-barite assemblage related to early Cretaceous intrusives (121 ± 5 m.y.), and (2) a later low temperature Au-As-Hg-Sb assemblage of near surface emplacement. The earlier sequence consisting of sparse galena and sphalerite in barite with anomalous amounts of zinc, lead, nickel and copper, associated with dikes of dacitic composition, is of little economic importance. The later sequence of gold, realgar, cinnabar, and stibnite associated with extensive silicification and argillic alteration of limestone beds, has resulted in important deposits of gold. Argillic alteration of hydrothermally leached carbonate strata has provided the environment in which the most prominent gold deposition took place. Carbonate minerals in the limestone host rock have been replaced by microcrystalline quartz and chalcedony to form stratiform silica masses and recrystallized lenses of euhedral quartz. Zones of porous silicification are light gray to white, elliptical in shape, and more or less follow bedding. Silicification is bordered by argillic alteration and pyritization. Deposition of gold usually lies in a zonal pattern that encircles chimney areas of silicification.

Jan 1, 1968

Aamot, Olav Crone, (M'29) Chem. Engr., Elektro¬kcmisk, Raadhusgt. 32, Oslo. Norway. . Aase. Glenn D., (J'40) Jr. Met., American Smelt. & Refin. Co., Selby, Calif. Abadie, Henry G., (J'43) Petr. Engrg., Avenal, Calif. Abadilla, Quirico A., (M'38) Min. Engr., Dir., Bureau of Mines, Manila, P. I. Abbott, Agatin Townsend, (J'40) Jr. Engr., Phelps Dodge Corp., Morenci Branch. Morenci. Ariz. Abbott, Clarence E., (M'04) Civ. Engr. V.P., Tennessee Coal Iron & R.R. Co., 1542. Brown Mars Bldg. Birmingham. Ala. Abel, Raymond L.. (M'23) Chem. Engr., Com¬manding Officer, Pittsburgh Chem. Warfare urement Dist., American Bank Bldg.. Pittsburgh. Pa. Abel, Walter D., (M'32) Min. Engr., Supvr. Engr.. R.F.C., Los Angeles, Calif. Abele, Louis T., (M'31) 423 3rd Ave., Decatur. Ga. Abell, Leo M.: (M'31) Mill Supt. & Met.. Em¬ peror Gold Min. Co., Ltd., Vatukoula. Fiji Islands. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Fan. Abernathy, Jack H., (M'40) Cons. Petr. Engr., First National Bldg.. Oklahoma City, Okla.

Jan 1, 1943

By R. S. Olson

An analysis of the wash thickener-two stage filtration circuit was undertaken to quantitatively describe the circuit performance. On the basis of information developed in this study, the factors of major importance in reducing soluble loss are: filter wash, wash zone size, filter capacity, filter feed pulp dilution, blow back, filter cloth, water to repulp, water to primary wash, water to feed pulp and thickener underflow. The wash thickener-two stage filtration circuit has been used in many hydrometallurgical plants to separate solute from leach solids. As many as 20 to 30 plant operating variables determine the performance of the wash circuit and hence the soluble loss. The complex relationships of these variables, with each other and with soluble loss, make the evaluation of their effect on mill performance difficult. An analysis of this type of circuit was undertaken to quantitatively describe the circuit performance. THE CIRCUIT The diagram in Fig. 1 represents the operation of the wash thickener-two stage filter circuit. This circuit provides for counter current, cross current or for a combination of countercurrent-cross current operation. The feed pulp stream, J, is intended to include any solution or water, other than primary and secondary filtrate, which enters the wash thickener. Except for filter washing, the operations in the circuit are simple mixing operations which can be described by material balance. The concentration of solute in the filtrate and cake solution after application of wash liquor cannot be described by simple material balance. The displacement washing equation, derived by Rhodes1 and extended by Choundhury and Dahlstrom,2 appears to best describe this case of miscible displacement in porous media. In a useful form, it is

Jan 1, 1963

By Marvin P. Barnes, John G. Simos

The Park City District, Utah, is situated in the Wasatch Range at the intersection of the westward extension of the axis of the Uinta Range. Ore has been mined almost continuously from the first discovery in 1869 to the present day, with a total production of over 14 million tons. Sediments of Carboniferous to Triassic age have been folded into the northerly plunging Park City anticline and subsequently modified by thrust faulting, diorite and diorite porphyry intrusions, and strong east-west normal faulting during the Laramide orogeny. Younger andesitic volcanics partially cover the eastern edge of the district. The ore bodies occur as both lode and bedded replacement deposits over widely scattered localities. Near surface, high-grade silver "bonanza" ores were mined in early days from the Ontario and Daly Lodes, which occur along the east-west zone of faulting near the center of the district. Other lode or fissure deposits were found along the Mayflower and Hawkeye faults to the east and southeast. Large bedded replacement silver-lead-zinc ore bodies associated with east-west zones of fissuring, have been mined from favorable horizons in the Park City Formation in the Daly West and Judge mines. A series of long, narrow, high-grade, replacement ore bodies occur in the Silver King mine at a single horizon in the Park City Formation. Ore is currently being mined from strong bedded replacements in the Humbug Formation near the apex of the Park City anticline. Factors controlling ore deposition are: magmatic source, structural feeder systems, and favorable host rocks. Ore deposition along favorable beds is primarily a function of physical conditioning and secondarily of chemical composition.

Jan 1, 1968

Beyer Barometric Condenser The Ingersoll-Rand Co. is now offering to the trade complete steam­condensing plants for all service conditions. This equipment includes the Beyer barometric condenser, for' which the company has secured the patent rights, Imperial duplex and Ingersoll-Rogler straight-line reciprocating dry vacuum pumps and, where required, Cameron simplex and centrifugal pumps. The Beyer barometric condenser is of the counter-current type, in which air and cooling water flow in opposite directions. The steam inlet is at the bottom of the condensing v el, the water inlet above and the air-removal opening at the top. The sheets of cooling water over owing the pool at the inlet point meet the entering steam. The two are brought into intimate contact by conical baffle plates which assist the water to absorb to its full capacity the latent heat of the steam. The non-condensable air liberated in the condensing action rises through the falling water to the removal point at the top, being cooled to practically the temperature of the incoming water. It is also to be noted that ample opportunity is given for the removal of the air content of the water before

Jan 8, 1916

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969