Search Documents

By Major N. R. Junner

Although manganese-garnets are rarely seen in hand specimens of the manganese ores and associated rocks, they have been detected by the writer in thin sections of all the ores and wall rocks that have been sliced, with the single exception of the Insuta deposit. Rhodonite, and an almost colorless amphibole, which appears to be manganiferous, are less common. Types of Occurrence (a) Rocks Composed of Manganese-garnet and Quartz The best known examples of this type are from near Bole and Wa in the Northern Territories of the Gold Coast, and from near Chama in the Gold Coast Colony. Normally these are fine and even-grained rocks, in which the garnets cannot be recognized in hand specimens. They are often stained with secondary manganese oxide. Thin sections examined microscopically are seen to be composed of aggregates of minute crystals of garnet in a matrix of mosaic quartz. Some manganese oxide and braumite (?) is often present, but other minerals are exceptional. The relative proportions of garnet and quartz in these rocks vary greatly and there is a complete gradation from quartz-rock to garnet-rock. (6) Rocks Composed Mainly of Manganese-garnet and Manganese Oxides Rocks of this type are known from Kalimbi Hill near Siripe, Pabini Hill near Bangwon, near Odumase and Konongo, and in the Ya Ya creek, about 5 miles east of Dunkwa. These are usually fine-grained banded dark-colored rocks, composed of abundant minute garnets in a matrix of black manganese oxide and braunite (?). A little microcrystalline is often present, and occasionally a little colorless amphibole. quartz (c) Rocks Composed of Rhodonite and Manganese-garnet Rocks of this type are not common. They are known from near Chama, and from the road between Senyong and Mangkuma. Some quartz is usually present. All these rocks resemble closely in texture and composition certain rocks from India, described by Fermorl as "gondite;" and they also resemble certain rocks described by Derby2 from the Queluz district,

Jan 1, 1927

By W. H. Emmons

ALTHOUGH gold is one of the rarer metals, it is widely distributed; it is found on all of the continents and in each of the grand metallogenic provinces of the earth. It is prominent particularly in the shield areas of the earth; these areas have produced a large part of the world's lode gold and in most of them gold lodes are more important than the lodes of other metals. The Scandinavian shield is the only one that has not produced much gold. Nearly all of the world's gold has been derived from lodes and from sands and gravels where gold placers formed by the destruction of lodes. The gold derived from magmatic segregations, from pegmatites and from contact metamorphic deposits is quite subordinate to that derived from auriferous lodes. The lodes include all veins and related deposits that are formed by hot waters that move along fissures or other openings and that deposit vein matter in the fissures and by replacement of the country rocks along the fissures. All of the shield areas of the earth are characterized by large areas of granitic rocks including granitic gneisses, granodiorites and other acid intrusives which here are included in the general term "granite." The granites are intruded into schists, ancient lavas and other rocks which here are designated as the "invaded" rocks. The granites are parts of what once were great batholiths: that is, they are the remaining portions of great deep-seated bodies that slope outward, have very irregular roofs and so far as known have no floors but extend downward to great though unknown depths. Some of them are scores or hundreds of miles across and contain islands or "roof pendants" of the invaded rocks at places where the roofs of the batholiths were low-that is, where erosion has not yet completely unroofed the batholiths.

Jan 1, 1932

By Theron Wasson

The discovery of eight new oil fields, two of which may be of major importance, was the outstanding record in Michigan this year. These new fields have helped to support the declining production from old areas and place the total of 18,559,000 bbl. in line with the past six or seven years. Thus, it appears that Michigan is doing its part in maintaining the production of the country in the third year of the war. The new fields are in the central basin area where oil was first discovered in Michigan, thus tending to focus attention on the deeper part of the lower peninsula of the state. Through 1944 the state of Michigan has produced a total of 222,-641,580 bbl. of crude oil from 100 pools, many of which arc relatively small. Among the previous1y discovered fields Reed City is still the outstanding producer, with Fork, Headquarters, and Adams following in the order named. The Reed City pool produced a little over 5,000,00 bbl., which was more than one third of the state's total for the year. Almost two thirds of the year's total oil production came from fields discovered in the past five years. Maps A map of the oil and gas fields of Michigan in 1943, published in the A.I.M.E. report for 1944,* shows the main producing areas and should be referred to if information in regard to their location is desired. The producing zones are shown in the columnar section in the same publi- cation." The data in Tables I and 2 have been carefully ' checked and every effort has been made to show as complcte information as possible. New Discoveries and New Developments Eight new producing areas were discovered during 1944 which, in order of importance, are: Deep River Field.—The discovery well in the Deep River field was drilled by Don Rayburn and others, and should be listed as a chance discovery, as, from a geological standpoint, it was not considered favorable until oil was found at a depth of 2838 ft. in a dolomitic layer in the top of the Dundee limestone. The first well was completed in January 1944, with an initial production of 2500 bbl. By the end of the year 15 wells had been completed, proying an area 2 1/2 miles long and 1/2 mile wide. Coldttater Field.-The Coldwater field was discovered in August 1944, by the Sohio Oil Co. Production is from secondary dolomite at the top of the Dundee at a depth of 3703 ft. To the end of 1944 nine wells had been drilled on 40-acre spacing. Essexville Field.—Essexville field was discovered by United Drillers and Producers, Inc. Eight wells had been completed to the Dundee lime by the end of 1944, and prospects were good for further development during 1945. Hilliards Field.—Hilliards field was discovered by Cook and Fortney. Production is from the Traverse lime at an average depth of 1588 feet,

Jan 1, 1945

By Rudolf K. Berkhard

Static soil investigations with more or less heavy loads and extensive borings do not always have efficient results; also, they are very expensive. The new geophysical method of dynamic tests described herein is simple and cheap and avoids several disadvantages of the routine investigation, thus forming a useful supplement to the older methods and even at times replacing various static tests. The fundamental principle of dynamic soil tests consists in the application of artificial vibration. The technique employed is essentially geophysical in nature and in some respects is akin to seismic studies. Artificial vibration may be excited by centrifugal forces resulting from eccentrically supported rotating masses. The reactions of soil and structures caused by these vibrations may be measured. Their dynamic constants, such as amplitudes, phase speeds, damping, reflection, and interference effects, can be investigated. This geophysical method has been used for several years with increasing success. The results of these tests, summarized at the end of the paper, indicate that this method opens a new field for the pkactical engineer in investigating soils (capacity and formation), foundations, dams and structures, and especially buildings that must withstand earthquakes. Methods Static Method.—The first and oldest tests to investigate the bearing capacity of the soil were carried out by static weights. The penetration of these weights, however, depends not only on the soil but also on the size and the form of their lower surface. The length of time the load acts is also important. To imitate actual field conditions, heavy weights and lengthy tests are required, both of which are expensive. Furthermore, the influence of static weights affects only the surface and does not penetrate into deeper strata, therefore substitutes and supplements for static tests have to include the time factor and consequently lead to dynamic investigations. Such dynamic investigations also affect

Jan 1, 1940

By Robert G. Woolery, S. Ramachandran, James A. Weber, Donald J. Hansen

Union Carbide began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.40 kg U3O8 /t) (0.80 lb U3O8) were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leaching project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. The operators were most generous in allowing us to visit their site and in answering our questions. They were also helpful in discussing the problems associated with heap leaching. Their experience confirmed our belief that it was possible to operate a heap leach profitably on material too low grade for conventional milling. Based largely on what we had learned from Western Nuclear's experience, we undertook a program involving a laboratory study to determine the characteristics of the mineral stockpiles, as related to heap leaching, and to conduct a pilot heap leach adjoining our Gas Hill mill. Basically the pilot heap construction and leach procedure were similar to those described in the literature l, 2 with certain modifications to permit detailed monitoring of the operation. In May 1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the following reasons: (1) The necessary equipment for heap construction was readily available. (2) Stockpiles of mineral from the various mining sites were on hand: (3) Construction of the heap could be made on an abandoned tailings pile minimizing problems associated with environmental approval. (4) Proximity of the mill would allow product streams to be absorbed into existing circuits. (5) Necessary utilities were available. (6) Tailings water from the existing circuit could be used for leaching. A program for the pilot heap leach was developed with the following primary objectives. (1) To confirm the data obtained in bench-scale tests particularly on uranium recovery, acid usage, and ore permeability. (2) To evaluate plastic liners used for base preparation. (3) To investigate heap configuration variables. (4) To determine heap leach amenability of the different mineral sources. (5) To establish the economics of heap leaching low-grade ores.

Jan 1, 1979

By M. R. Hatfield, F. J. Vosburgh

IN a recent article,† it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell-to keep it cool enough for safety and comfort and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a carbon tube nominally 2 5/8 in. o.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a 15-kva. transformer operating

Jan 1, 1941

By L. A. White

IN this paper it is proposed to follow the developments in the design of the lead blast furnace at Port Pirie from the time The Broken Hill Associated Smelters Pty. assumed control in 1915 to the present time, with special reference to the development of the system using two superimposed rows of tuyeres as is now in operation. Lead smelting operations first commenced in 1889, when the British Broken Hill Pty. Ltd. started its first furnace. This was followed by installing two more furnaces during the same year and another the following year. In 1892, Broken Hill Proprietary Co. Ltd. acquired the smelting works and combined operations with those at Broken Hill, New South Wales; by 1897, the whole of the smelting operations had been transferred to Port Pirie and thirteen blast furnaces were built to treat the Broken Hill ore production. In 1915, The Broken Hill Associated Smelters Pty. Ltd. took over from the Broken Hill Proprietary and have carried out operations since that time. From its inception, the present company started on a long range program of reconstruction, in which the development of the lead blast furnace has played a prominent part. A definite trend in plant development has been towards the simplification of plant control by a reduction in the number of operating units. The great advantages of technical control which resulted from the very simplified flowsheet established in the continuous refining process stimulated the desire to extend the principle to the smelting operation. Thus in the sequence of furnaces described here, it will be noted that the trend has been towards larger and, of course, fewer units. With each such development it is significant that the operating conditions and metallurgical results have shown steady improvement. Standard Furnace In 1920 there were seven furnaces operating, five of a type subsequently called the standard furnace and two of the original thirteen smaller furnaces, the latter type being used for the treatment of drosses, etc. produced from the refinery section, while the standard type carried out the main, lead-smelting operations. The standard furnace (figs. 1 and 2) had the dimensions given in table I.

Jan 1, 1951

By Richard D. Hagni

Mississippi Valley-type ore deposits contain significant quantities of minor elements, which are present partly in the form of separate mineral phases and partly in solid solution in the major sulfide phases for which these deposits are exploited. These elements, as separate phases, are: copper, mainly in chalcopyrite and enargite; cobalt and nickel, chiefly in thiospinels and bravoite; rare earth elements associated with certain fluorites; and native gold. Many economically important minor elements occur in solid solution in sphalerite, including silver, cadmium, iron, germanium, gallium, indium, thallium, cobalt, nickel, and mercury. Significant amounts of silver and antimony, and perhaps very small amounts of gold, are present in solid solution in galena. Chalcopyrite may contain small amounts of silver, molybdenum, bismuth, cadmium, cobalt, and nickel. Marcasite and pyrite may contain silver, thallium, cobalt, and nickel. Although some of the minor elements contained in the Mississippi Valley-type deposits are currently recovered at the smelters and refineries, many are lost in tailings, sludges, and slags; consequently, important quantities of these elements are potentially recoverable as non-conventional resources.

Jan 1, 1983

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By Cyril Stanley Smith, Earl W. Palmer

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization. MATERIAL USED After some preliminary heats had been made in the laboratory to determine the effect of copper, several castings from commercial air-furnace heats were obtained, and data from these alone are given here. Part of the metal was poured directly and part was treated in the ladle with the desired amount of copper before pouring. Green-sand molds were used, each holding two tensile test pieces of the form adopted by the Malleable Iron Research Institute, or two bars for graphitization studies, 5/8 in. in diameter and 9 in. long, fed through two enlarged sections equidistant from the middle and ends of the bars. Risers of suitable size insured sound castings. Tensile tests were made

Jan 1, 1935

By Edward B. Cook

The installation of the Gayley dry-air process appealed specially to the management of the Warwick Iron & Steel Go., for the reason that for fifteen years records had been kept at the works of the company, showing the amount of water entering the furnace in the form of aqueous vapor, and careful observations had been made of its effect upon the working of the furnace. Some years had proved much worse in their effect than others, on account, not only of excessive moisture, but also of great variation in the moisture from day to day, and sometimes within a few hours. It had been found impossible to make a satisfactory percentage of high-silicon foundry-iron in summer, even on high fuel; and for some years the endeavor had been made so to arrange the sales that, during July and August, only a small percentage of the iron produced would be required to carry more than 2 per cent. of silicon. Our larger furnace, running on basic iron, year after year, produced in February a tonnage 20 per cent. higher than in August, 011 a much lower fuel-consumption, while, at the same time, the summer months were marked by " messes," tuyeres closed by slips, and other irregularities, constituting serious additional business losses. It will be easily understood, therefore, that the records made at the Isabella furnace after the installation of the dry blast in 1904 possessed special interest, and were closely watched by us. On the basis of our own experience, we argued that if the moisture could be kept low, and also uniform, the cost of installation would be more than justified. The subject was brought before our Board of Directors in the fall of 1905; and in the spring of 1906 it was decided to install a plant of sufficient

Jan 1, 1909

By J. H. Henderson, J. Naar

The displacement of a wetting fluid from a porous medium by a non-wetting fluid (drainage) is now reasonably well understood. A complete explanation has yet to be found for the analogous case of a wetting fluid being spontaneously imbibed and the non-wetting phase displaced (imbibition). During the displacement of oil or gas by water in a water-wet sand, the porous medium ordinarily imbibes water. The amount of oil recovered, the cost of recovery and the production history seem then to be controlled mainly by pore geometry. The influence of pore geometry is reflected in drainage and imbibition capillary-pressure curves and relative permeability curves. Relative permeability curves for a particular consolidated sand show that at any given saturation the permeability to oil during imbibition is smaller than during drainage. ' Low imbibition permeabilities suggest that the non-wetting phase, oil or gas, is gradually trapped by the advancing water. This paper describes a mathematical image (model) of consolidated porous rock based on the concept of the trapping of the non-wetting phase during the imbibition process. The following items have been derived from the model. 1. A direct relation between the relative permeability characteristics during imbibition and those observed during drainage. 2. A theoretical limit for the fractional amount of oil or gas recoverable by imbibition. 3. An expression for the resistivity index which can be used in connection with the formula for wetting-phase relative permeability to check the consistency of the model. 4. The Iimits of flow performance for a given rock dictated by complete wetting by either oil or water. 5. The factors controlling oil recovery by imbibition in the presence of free gas. The complexity of a porous medium is such that drastic simplifications must be introduced to obtain a model amenable to mathematical treatment. Many parameters have been introduced by others in Iprogressing" from the parallel-capillary model to the randomly interconnected capillary models independently proposed by Wyllie and Gardner3 and Marshall4. To these a further complication must be added since an imbibition model must trap part of the non-wetting phase during imbibition of the wetting phase. Like so many of the previously introduced complications, this fluid-block was introduced to make the model performance fit the observed imbibition flow behavior. THE IMBIBITION MODEL ASSUMPTIONS The following assumptions are common to many two-phase models previously described. 1. The wetting characteristics of the medium are clearly defined. 2. When two fluids co-exist in the medium, the wetting phase will fill the smaller pores and the non-wetting fluid the bigger ones. 3. The pores have a circular cross section. 4. Apparent pore radii are related to the capillary pressure (drainage) by

By R. L. Smith, J. L. Rutherford

ZONE refining, as developed by W. G. Pfann,1 has been used extensively for the purification of semiconductors. This method has made it possible to obtain the extremely high purity material necessary for the transistor industry. It has also been utilized to some extent for the purification of relatively low-melting-point metals. However, very little attention has been given to reactive, high-melting-point materials, with the exception of silicon. For this element, it has been necessary to use the floating zone technique in order to avoid contamination from the crucible containing the melt. The method is one in which a narrow molten zone is formed in a vertical rod by induction heating. The molten zone is supported between the two solid sections of the rod by surface tension. It is then moved longitudinally along the rod in order to effect a redistribution of solute. This technique has an advantage over the horizontal boat method, since crucible contamination is avoided. It has the disadvantage of being a much more difficult technique than zone refining in a crucible. Furthermore, it is necessarily a slow process, since only one zone at a time can be formed. However, the floating zone process offers a means of obtaining high-purity metals that are either not available, or can only be obtained in powder or pellet form as the result of complex chemical or electrochemical methods. It should be emphasized that the process is not effective in removing all impurity elements. Those that cannot be redistributed in an ingot during zone melting must be removed by some other means. Very little is known of the prope~ties of very high purity reactive metals such as iron, titanium, zirconium, beryllium, etc. It is quite likely that trace elements in such metals can affect their properties drastically. Therefore, one of the primary objectives of this work is to study the properties of metals which have been obtained in the purest form available and then zone refined. Trace elements can be introduced in a variety of ways, such as by inserting wafers between solid portions of the ingot to be melted, by placing the

Jan 1, 1958

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942

By W. L. Falke, A. A. Cochran

A basic problem in connection with manganese is to find economical ways to utilize domestic resources. As a part of its program to conserve domestic mineral resources and to reduce dependence of foreign sources, the Bureau of Mines had conducted extensive research to broaden manganese technology and to find economical, technically-feasible processes for recovering manganese from these low-grade resources. This paper analyzes some of the major difficulties which have been encountered in previously proposed processes for treating low-grade manganese ores and discusses a process which may circumvent many of these difficulties. Vast deposits of low-grade manganese ore exist in the U.S., yet domestic production is insignificant compared to the more than 2 million tons of ore imported yearly into this country.' A basic problem in connection with manganese is to find economical ways to utilize domestic resources.2 As a part of its program to conserve domestic mineral resources and to reduce dependence on foreign sources, the Bureau of Mines has conducted extensive research to broaden manganese technology and to find economical, technically feasible processes for recovering manganese from these low-grade resources. Although a great many processes have been proposed for treating domestic manganese resources, a failing of many of them is that too many steps are involved for economical operation.' Some of the major processes that have been proposed were reviewed by Norman and Kirby.3,4 Chlorination processes have become increasingly useful as a means of recovering valuable metals from raw materials, because the relative cost of chlorine (Cl2) and hydrogen chloride (HC1) has decreased through the years, and because the corrosion resistance of materials of construction has been improved. The objective of these processes is to form metal chlorides that are more volatile or water-soluble than are the corresponding oxides or sulfides; these compounds then can be separated from the gangue or other minerals by volatilization or leaching. Several chlorination processes for the recovery of manganese have been investigated by the Bureau of Mines5-8 and others; the major chlorination processes were reviewed in 1963, and their main features were compared.4 In all these processes, the simultaneous leaching or volatilization of iron chlorides with manganese chloride (MnCl2) is a problem, and the more iron that is present, generally the greater the problem. The leaching step is not highly selective, and the product of this step is, at best, suitable only for the production of ferromanganese or for further processing to remove iron. The product of the volatilization step is, in all cases, a mixture of iron and manganese chlorides that contains too much iron even for ferromanganese production, and must undergo additional processing steps for iron removal. THERMODYNAMIC CONSIDERATIONS The literature indicates that the desired chlorination reactions will proceed at practical rates at temperatures near 1200°K (927°C). Free energy changes at 1200°K for the critical steps of the reduction and chlorination reactions9-11 follow: Most of the research on chlorination processes for manganese recovery has been done with HC1 rather than with C12, for the following three main reasons: 1) Recycling of the chlorinating agent, which is economically vital, appeared to be easier for HC1

Jan 1, 1968

By Donald J. Drinkwater, M. C. Fuerstenau

Many important contributions to the more fundamental aspects of mineral processing have been made this past year. Mular1 researched the flotation characteristics of pure zinc oxide and also samples that had been doped with Al+++ and Cu++. Correlation of the response of pure zinc oxide to oleate flotation with a calculated zpc (from solution equilibrium) suggests that adsorption of oleate ion is coulombic in nature. Doping the sample with Al+++ (which will make the ZnO more n-type) had a marked effect on the maximum value of pH at which 50% recovery was obtained at constant collector addition. That is, when 0.5 mole percent Al+++ was added, the pH for 50% recovery was reduced by about four units. Treatment with Cu++ was found to have little effect on the flotation response of zinc oxide, even for additions of one mole percent. Since the zero points of charge of the Al+++ doped powders were not measured, it was not possible to correlate flotation data of these samples directly with charge phenomena.

Jan 2, 1966

By R. S. Cartwright

TWO types of automatic drilling controls, the Halliburton and the Hild, are now available and are coming into more or less general use in deep drilling. The primary function of both is to maintain a safe limit of torque on the drill pipe, this being accomplished by automatically controlling the weight or pressure on the cutting tool. Neither type will necessarily increase drilling speed, but by permitting advantage to be taken of "breaks" in the hole higher average cutting speed may be maintained. The control is essentially a safety device, and should be considered as such. It is not the purpose of this paper to discuss the merits of drilling controls, although the advantages over manual feed at the brake drum are obvious, but rather to point out some of the limitations. The Halliburton Control The Halliburton control is designed to operate during drilling through the agency of the draw works. Automatic and constant control of the torque on the bit is governed by clutches on the control itself, and the line shaft to drum shaft drives on the draw works. In operations other than drilling the control is simply a jackshaft between prime mover and draw works. It is, of course, adaptable to any type of power. Because control of the torque on the bit is dependent on the various ratios or clutch combinations available on the Halliburton control and the draw works, it follows that there are certain limitations in points of control. Table 1 shows the possible ratios which can be obtained with the control and a popular type of three-speed draw works, it being assumed that the highest possible gear combination—the combination which when engaged will suspend the least amount of weight—has a value of 1.00. According to the table there are "blind spots" in the series. This is true particularly among the lowest ratios, which are most used to suspend the major part of the weight when great depths are reached. It will be noted that there is a difference of nearly three units in the value of the

Jan 1, 1929

THE Geophysics Education Committee has devoted several years to a consideration of the problem of training geophysicists. Past reports have dealt largely with fact finding and with the discussion of particular aspects of geophysical education. In the present report it is proposed to review the subject more comprehensively. This involves the question of what educational qualifications the geophysicist of the highest professional standards should possess, and the related question of what changes must be effected in existing educational institutions in order that prospective professional geophysicists may obtain instruction of the desired quality. The type of geophysicist here contemplated is one familiar with what is known already in the several branches of earth physics, and capable not only of following contemporary progress in any of these branches, but of contributing to that progress in a research capacity. Geophysics in its broadest sense, as has been emphasized repeatedly by this Committee, is the study of the physics of the earth and of terrestrial processes. This includes both the static and the dynamic characteristics of the gaseous, the liquid, and the solid portions of the earth, as well as its gravitational, thermal, and magnetic and electrical manifestations. Some branches of earth physics have been cultivated but slightly; others have reached an advanced state of development. Those branches whose development is sufficient to warrant explicit recognition in the form of organized Sections of the American Geophysical Union are: geodesy, seismology, tectonophysics, and volcanology, dealing with the rock constituents of the earth; oceanography and hydrology with the aqueous constituents; meteorology with the atmospheric constituents; and terrestrial electricity and magnetism with the electromagnetic manifestations. At present, instruction on the professional level in any of these branches of earth physics can be obtained in but few universities in North America. In most institutions where such instruction is undertaken different subjects are given in different and independent departments. Geodesy and hydrology are taught, if at all, as a part of civil engineering. The nearest approach to volcanology and tectonophysics ordinarily is represented by petrology and structural geology given

Jan 1, 1944