Search Documents

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

Production scheduling of open pit mining is a key area as it deals with the management of operating cash flows of mining companies. The efficiency of long-term schedules is usually assessed with economic criteria such as net present value (NPV), discounted cash flow rate of return (DCFROR) and payback period, which are not sufficient on their own for revealing the complex picture of the decision-making process.This paper offers a thorough analysis of the most important contemporary criteria of long-term production scheduling, as way to provide the mining practice with a new approach to the decision-making process. The list of criteria includes technological, economic and probabilistic ones. A detailed case study is provided aiming to illustrate the applicability of the criteria for comparing the scheduling approaches regarding the economic interests of a mineÆs owner and contractor. The results obtained can be used for revealing new trends in the current methodology of open-pit production scheduling optimisations.

Sep 26, 2011

By R Shaw, R Williamson

Global iron ore demand, sparked by ChinaÆs rapid industrialisation and emergence as the worldÆs newest steel market, has seen iron ore groups investing heavily in production capacity as well as infrastructure. The success of these new projects depends heavily on reliability, competitiveness and quality control in an increasingly demanding trading environment. Furthermore, the iron ore industry continues to improve its competitiveness in mining practices, technology innovation and management processes. The continued fine tuning of these sectors will be critical to the success of the industry in the years ahead, and this mining sector will continue to demand process improvements from their service suppliers to maintain competitiveness. Automation offers a real solution to these demands. A crucial quality control element in mining, beneficiation, stockpiling and shipping stages is ensuring representative samples of ore are taken along each step of the process. When these samples reach the laboratory it is imperative that the sample is representative of the entire stream and that no induced errors occur. Examples of automation start with mechanical primary and secondary samplers in the run-of-mine processes through to sample tower and laboratory crushers, dividers and collectors. Automation is widely used in many forms to provide reliable and repeatable samples for analysis whilst providing a safer working environment. Laboratory automation systems in use today vary from simple linear systems to sophisticated robotic cells. Sample automation in the iron ore industry has resulted in many benefits for both producers and their customers. The most significant benefits have come in the form of higher safety standards whilst reducing sample error, sample handling and sample contamination during collection. These benefits have been further augmented by reliability and repeatability of automating the final sample preparation and analysis stage. Today these benefits are reflected in reduced costs of sampling and improvement in both turnaround time and quality of results, whilst complying with Australian safety and ISO sampling standards.

Jan 1, 2007

By M F. L Gibson

The issue of flyrock is very important in the operation of all mineral extraction sites that use blasting. Unlike the other environmental effects of blasting, ground vibrations and air overpressure, flyrock is (or should be) a rare event, with severe consequences which may include damage to property, injury or fatalities. These physical consequences are often matched by a loss in public confidence in the management of the operation, mistrust and bad press. In this work a deterministic analysis of flyrock was carried out using the equations of a particle in motion with drag. The solutions to these equations were used to reproduce the curves of Lundborg et al (1975) for the relationship between flyrock boulder size and maximum ejection distance. A probabilistic approach based on Monte Carlo simulation was built up with the analytical model using published data together with local case study material. A typical quarry blast situation was modelled and estimates of safe standoff distances were determined using risk assessment techniques.

Jan 1, 2001

By Hall G

The Mount Isa silver-lead-,zinc deposit possesses a number of features which sets it apart from usual occurrences of ores containing those metals. The deposit has been described in vario:us papers, but development upon deeper levels during the past two years has, yielded much information not hitherto published. Purpose of the present paper is to furnish a unified and coherent perspective by tracing briefly the full rock deformational and mineralization processes responsible for the ore deposition. The paper represents the outcome of ten years' organized geological effort at Mount Isa. Information contained in it supersedes that previously published.A bibliography of published articles relating to Mount Isa ore deposition is appended. In preparing the present paper previously published data have been drawn upon freely wherever applicable. The authors are especially indebted to the papers by Grondijs and Schouten, and by O'Malley and McGhie, which present results of systematic microscope studies of thin and polished sections from comprehensive suites of Mount Isa ore.

Jan 1, 1942

By K Akiro

Volcanogenic massive basemetal sulphide and gold mineralisation of predominantly low sulphidation style has been located within Lower Tertiary basaltic and felsic volcanic and sedimentary sequences at Ufuo, in the Left April River area, northwest Papua New Guinea. The four discrete massive sulphide bodies, which have been so far identified, occur within a 3 +5 km area situated within a north west trending structural corridor. The sulphide bodies are all localised on the margins of the corridor where the bounding major through going faults are transected by regional faults. Mineralisation is characterised by massive pyrite-bornite-sphalerite-barite-quartz-anhydrite deposition with later galena-tennantite-chalcopyrite. Minor phases include enargite, goldfieldite and bismuth sulfosalts. Jasperoidal silica lenses and bioturbated sediments are closely associated with the massive sulphides. Basemetal sulphide mineralisation is also closely associated with phyllic-style quartz-sericite- altered host rocks underlying the massive sulphide lenses. This mineralised phyllic alteration is localised to fractures, veins and breccias that cross-cut propylitic style alteration characterised by quartz, epidote, chlorite, adularia and zeolite. The mineralised system possesses several hydrothermal features consistent with a copper-rich submarine exhalative volcanic hosted massive sulphide (VHMS) system, ie discrete massive sulphide bodies with abundant barite, associated jasperoidal silica and bioturbated sediments. However, exploratory drilling of the alteration zone underlying each of the massive sulphide bodies has not identified a well-defined zoned alteration pipe that is characteristic of such systems. The alteration is also similar to that of a porphyry-related low sulphidation system in which phyllic alteration has overprinted a regional propylitic style assemblage. The presence of sporadic enargite (and ?tennantite/tetrahedrite) suggest there were intermittent pulses of acid fluids in the system probably derived from exsolved magmatic SO2 which flowed directly to the surface along reactivated faults. The occurrence of tellurium and bismuth minerals is also consistent with a magmatic contribution to the metalliferous hydrothermal fluids. It is proposed that the VHMS orebodies are the products of submarine exhalative deposition generated by a crystallising magma emplaced within crust of on-going tectonism. Ufuo mineralisation is similar to many VHMS deposits elsewhere in that it is unclear whether the metals are derived from the magma directly, or via seawater leaching of the wallrock. Additional studies such as oxygen isotope analysis may assist in resolving this issue. If the metals are shown to be of direct magmatic origin then there may be good prospects for discovering economic-grade porphyry-related mineralisation at depth below the massive sulphide deposits.

Jan 1, 1999

The tragedy of the Moura No. 2 incident has lost much of its emotional mileage for those organisations that thrive on loss and suffering. However, for the families, workers, mine owners and operators in the Queensland underground coalfields, the challenge of delivering a positive outcome, though well underway, is in its infancy. The pressure created by interested parties is necessary for overcoming the inertia involved in change; but they cannot deliver the change. The responsibility ultimately resides at each individual minesite with the people who work there each day.

Jan 1, 1998

By H Parra, D Zenteno

Fragmentation modelling has been in use in the mining industry for a long time; however, there are still some aspects to tackle with regard to its use for strategic/planning and day-to-day purposes.On one hand, an important amount of resources are allocated to the task of calibrating and validating a good fragmentation model. Nonetheless, errors during the implementation stage introduce uncertainty into the prediction.On the other hand, it is common practice in the mining industry to use only discrete values to represent the fragmentation from blasting (k20, k50, k80), which provides a biased interpretation of the situation as, for instance, the best and worst possible cases are not taken into account. This is particularly critical when a continuous improvement philosophy has been adopted and modelling is used to either modify the drilling and blasting designs or plan ahead.It is well known that every site has particular conditions (rock mass, equipment, drilling and loading practices, among others) that often define unique trends in implementation. These trends can be captured using statistic and probabilistic techniques and then used as proxies for further analysis.This paper explores the potential of including implementation data in the form of probabilistic distributions into the Swebrec model to improve the performance of this engineering tool during the decision-making process.The fragmentation results of four designs were modelled using three different degrees of accuracy in the implementation for the burden, spacing and explosive column length.The data analysis showed that the probabilistic approach helps to achieve a broader perspective regarding the fragmentation that it is possible to obtain and the implications for the subsequent processes. The analysis also showed that the likelihood of producing similar fragmentation with different designs (involving different powder factors and costs associated) increases with the variability of the implementation.CITATION:Parra, H and Zenteno, D, 2015. Evaluating the inclusion of the implementation variability into fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Lastra, Y Choi, C Hamilton, P Kondos

Hydroseparation (http://www.cnt-mc.com) was used to concentrate sized fractions (from <38 ¦m to 150 ¦m) of various ore products ahead of carbon-in-pulp (CIP)-treatment. The resulting size-by-size concentrates were mounted as monolayer polished sections and subjected to automated unattended precious metal searches by image analysis (see Lastra, Wilson and Cabri, 1999). Systematic variations in Au-deportment permit quantification of Au reporting as discrete grains from fresh-feed through to pressure oxidation (POX)- and CIP-feed. Application of hydroseparation, image analysis and assays to characterising tailings (from <10 ¦m to 106 ¦m) from four mine sites is also described. Results are encouraging enough to predict that the combination of hydroseparation (HS) and automated image analysis could become a standard methodology for study of precious metal ores and metallurgical products.

Jan 1, 2008

The Energy Authority of NSW has wide powers and responsibilities conferred by its Act which are pertinent to the State's coal industry and its development into the next century. With respect to coal, the broad objective is to maximise the benefits to NSW and its people derived from the State's coal resources. The initial focus of the Authority's coal-related activities in the late 70's and early 80's was on petroleum substitutes from coal. Research was supported, especially on hydrogenation, and the Authority participated in the Joint Australia/Federal Republic of Germany coal-to-oil feasibility study. It also co-ordinated a State Government initiative to involve the private sector in examining the possible establishment of a synthetic fuels industry based on Hunter Valley coal. With a short-fall in world-wide petroleum supply now seen as less likely for some years, the Authority is looking also at ways of working towards the broad objective in the field of coal utilisation on both domestic and export markets. Areas of interest include possibilities for using washery rejects, means of making NSW coal more competitive as an energy source, use of coal-seam gas and new or special technologies for burning coal. The future is expected to see renewed interest in producing petroleum substitutes, and coal - as the State's major energy resource - is seen as a strong contender as a basis for such an industry. Developments in coal-based power generation are also expected to have an impact, with advanced technologies having a possible place here as well as Overseas.

Jan 1, 1987

The knowledge in the field has been reviewed by literature studies, and using experience from personal research in sublevel caving. There is a lot of material regarding gravity flow of fine grained materials in bins, but the theory of flow for these materials are normally not applicable for coarse blasted rock. This study was therefore concentrated towards coarse rock fragments created after blasting in orebodies. The goal for this study was to make a report of known knowledge, and identify what we have to learn more about. The Bergmark-Roos theory, which was a paradigm shift in the science of gravity flow, is today the best mathematical theory for calculation of the drawbody for a homogenous material or when we wish to simulate the mean drawbody for a large number of draws. The Bergmark-Roos theory must however be improved, so it can take into account the flow pipe effect. When this is done it will be possible to construct a 3D computer model for calculation of ore extraction versus amount of loaded ore and waste. It is also necessary to find the 3D shape of the flow cone to be able to calculate the 3D ore rest that normally develops on footwalls. Calculations should be done for the draw on several sublevels including determination of the ore losses and temporary ore rests. First when this computer model is developed optimisation of ore recovery and waste rock dilution can start for a given orebody. The author points out the importance for international co-operation and standardisation of methods for determination of material properties. More field tests and model blasting tests should also be done. When enough knowledge is gathered, a handbook of the optimisation of sublevel and block caving should be written.

Jan 1, 2000

This paper reviews recent advances in geophysical tools for mineral exploration. It does not restrict comments to methods which are usually applied in the tectonically active belt surrounding the Pacific Ocean, where geophysics has often been secondary to geological prospecting (eg visual recognition of surface alteration) and drainage geochemistry; but considers geophysical tools applied to a broader range of both deposits and terrains. For example, the subdued topography of much of Australia and Canada has lent itself to the development and extensive application of airborne methods. In Australia, deep weathering and transported cover have necessitated the use of geophysical methods to not only detect anomalies but also to map and understand basement geology. This same weathering has caused specific problems, particularly for electrical methods, but recent improvements in instrumentation, processing and visualisation have largely overcome them. A great deal of geophysical data is now being collected by government agencies, often from the air, and made readily available to explorers. In several Australian states it is free, often on line, and in almost all cases it is relatively cheap. These regional data sets are often augmented by more detailed local surveys in areas of interest. Although æanomaliesÆ are still important much more is being done with the high quality data which is now available The results are used for geological mapping, to test geological hypotheses, to construct detailed 3D geological models and, together with fluid flow modeling, to predict optimum locations for mineralisation.

Jan 1, 2004

The arbitration process, and its drawbacks: Any time you have taken part in a major arbitration, and the decision, when it comes out, is not what you thought it would be (which is bound to happen occasionally), the normal reaction is something like æthe arbitrator got it wrongÆ. Again normally, when you have cooled down a bit, and you look in more detail at the decision, you can see, probably, æwhere he got it wrongÆ (it is only male arbitrators who get it wrong). Ultimately, when reason prevails, and you reflect on it, you can see that what really happened was that you failed to get the arbitrator to see what you were getting at in the point or points concerned. This is doubly frustrating, when you consider what has been involved in getting to this point, having been through it all at least twice. An alternative to this process may be the dispute review board.

Jan 1, 1999

By S L. Barbour

Measurement of the net percolation from the base of a cover system into the underlying waste material is a key component of a cover system monitoring program. The units of measure (ie a percentage of precipitation or rainfall) are simple to understand for all stakeholders, which increases the importance of obtaining representative net percolation values. In general, lysimeters are used to measure net percolation across the cover material-waste material interface; however, the design of lysimeters for cover system monitoring programs in the mining industry have typically not considered fundamental aspects of lysimeter design. Lysimeter design is typically thought of as being conceptually simple, when in reality the design, installation, and operation of lysimeters is often counter-intuitive, due to the complexities of flow through unsaturated soil systems. This paper puts forward a methodology for lysimeter design while also presenting the fundamental design variables that should be considered. Lysimeter design for differing climates, cover materials, and waste materials is discussed. Finally, the performance of lysimeter designs previously installed in the field at sites in Australia, Canada, and the United States are subjected to numerical modelling to determine whether net percolation is being measured properly.

Jan 1, 2003

By M Chen, W S. Ng, Y Liu

In the processing of refractory gold-bearing sulfides, pressure oxidation (POX) is commonly known for its role in liberating the gold in solid-solution via oxidation of the sulfide occlusions. For deposits that contain arsenic-bearing species including arsenian pyrite and arsenopyrite, POX serves an important secondary function in the fixation of arsenic, via the hydrothermal precipitation of stable arsenates such as scorodite and basic ferric arsenate sulfate (BFAS). There have been various investigations on the impact of different POX conditions on arsenic precipitation and the stability of the formed phases, but less is known about the changes to the arsenic carrier that occur in the curing stage, which follows directly from POX. The primary function of curing is to coax the dissolution of sulfates to reduce lime consumptions during cyanide leaching, and the slurry is kept at elevated temperatures near 100°C to achieve this. While the arsenic-bearing phases are expected to undergo transformation during this stage, there has thus far been limited experimental evidence. In this study, the effect of curing time and curing temperature on the arsenic-bearing species and arsenic deportment in the POX product has been investigated. Leaching of the curing products was also conducted to examine the stability of the arsenic species in the solid precipitates.

Aug 24, 2022

Structural analyses of oriented bore core sections from the West Wallsend No.2 Colliery Holding together with investigations in adjac- ent collieries and on the surface delineated structural phenomena. The rocks examined are anisotropic due to strongly developed bedding planes and the presence of penetrative joint planes. Joints, in this context, are regarded as mechanical discontinuities, they are genetically identif- ied wherever possible and their spatial attit- udes are determined and geometrically related to the regional structure. Identifiable anisotropies in the roof- and floor-strata of the Borehole Seam render favour- able mining directions for longwall and bord and pillar layouts.

Jan 1, 1972

By Pate W. T

This paper describes the development of a dynamic flowsheet simulator for comminution operations. Object oriented software design allows the handling of multiple ore types, blended into multicomponent feed streams. Software objects have been c

Jan 1, 1998

By G R. Ballantyne, B Putland, I Lovatt, M Di Trento

The Tropicana Gold Mine, owned by AngloGold Ashanti Australia Ltd (70% owned and managed) and Independence Group NL (30%) is located 330 kilometres east-northeast of Kalgoorlie, Australia, in the newly developed Albany-Fraser Orogen. Following extensive feasibility studies, a high pressure grinding roll (HPGR)-ball milling circuit was selected based on the reduced power requirements and thus reduced operating expenses. The HPGR-ball mill circuit was estimated to require 75% of the energy of a standard semi-autogenous grinding (SAG) mill circuit. Even with an anticipated greater capital cost, the HPGR-ball mill circuit was found to give significantly better financial returns in all cases investigated in the feasibility study. A comparison between the specific energy requirements of the HPGR, crush and SAG based circuits (SABC) from the feasibility work was conducted and the HPGR circuit was found to be considerably more energy efficient. A survey was conducted and the efficiency of the HPGR was similar to both the overall circuit design and the HPGR laboratory results, reflecting the accuracy that is possible for design and operation of HPGR circuits.Between 2015 to 2016, the Tropicana circuit has achieved a 20% increase in throughput from 780 to 930 t/h, and this increase has been maintained in 2017. This improvement can largely be attributed to upgrades to material handling processes, increased HPGR speed and smaller HPGR screen apertures. The result of these changes has been to increase the ball mill capacity by increasing the breakage conducted by the HPGR.CITATION:Ballantyne, G R, Di Trento, M, Lovatt, I and Putland, B, 2017. Recent improvements in the milling circuit at Tropicana mine, in Proceedings MetPlant 2017, pp 73–83 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By D Hume

During 2001 the Ridgeway Gold Mine, driven by company initiatives and recent NSW legislation (General Rule 2000), developed and implemented Major Hazard Management Plans to control significant hazards identified at the underground mine. The paper presents the objectives, issues, outcomes and process involved in the development and implementation of the plans at Ridgeway. The sharing of the experience gained and an overview of the intended way forward will offer a valuable insight for other mines considering embarking on a similar journey.

Jan 1, 2002

Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. Since 1980, Australia's share of the world's output of these minerals has fallen. Exhaustion of known resources, together with the changing composition of new deposits, is expected to result in Australia's share of the rutile and zircon output continuing to decline. Its role as a major supplier of upgraded ilmenite, that is synthetic rutile, is expected to increase. In 1994, the Bureau of Resource Sciences assessed Australia's demonstrated resources of mineral sands as follows: rutile 14.4 Mt, ilmenite 132.5 Mt, and zircon 21.0 Mt. These resources are located along the coast of Queensland and New South Wales, in the Murray Basin of New South Wales and Victoria, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth. However, some 45 per cent of rutile and zircon resources along the coast of Queensland and New South Wales are not available for mining because of environmental concerns. World demonstrated resources are estimated at 40 Mt (contained TiO2) for rutile, 50 Mt for zircon and approximately 312 Mt (contained T1O2) for ilmenite. Outside of Australia, the most important resources of rutile, ilmenite and zircon are in South Africa (rutile, zircon , and ilmenite in the form of titania slag), Sierra Leone (rutile), India (ilmenite, zircon and rutile), and Canada (hard rock ilmenite). Significant resources of ilmenite occur in Madagascar and Mozambique.

Jan 1, 1996