Search Documents

By Sulanto J, Talonen T

In the mid 1960's Outokumpu considered building a lead Flash Smelter on the basis of Flash Smelting technology developed first in the late 1940s for smelting copper concentrates. Pilot scale tests were carried out and the process was found technically sound. The project was however not economically viable under Finnish conditions and it was cancelled. In 1981 pilot plant tests were restarted after many enquiries from the primary lead producers. All the know-how and development made in copper and nickel smelters was applied to the Lead Flash Smelting process and the tests were successful. Outokumpu has so far tested several types of lead concentrate with lead contents ranging from 28 to 75 per cent. The concentrate is oxidized and smelted to metallic lead and slag directly in the Flash Smelting Furnace using high oxygen enrichment of tonnage oxygen. Fossile fuel is used in the Flash Smelting Furnace in cases when the feed material does not contain enough latent heat to smelt the furnace products even though pure oxygen is used for oxidation. Thus the process results in a low consumption of extraneous energy. Use of oxygen results in a small gas flow but it is rich in sulphur dioxide. The gas treatment facilities and sulphur recovery plant will be small in size and low in investment cost. The process is flexible and can produce stable quality of products from different types of raw materials. Quality of lead bullion especially the sulphur content can be regulated over wide a range, from 0.1 per cent upwards according to the needs of the refinery.

Jan 1, 1984

Of all of the processes in the mining cycle, blasting has the greatest impact on the efficiency of both mining itself and the initial stages of ore processing. The cost of blasting can be readily accounted for, but the true benefits of an effective blasting operation are seldom measured or reported. This means that blasting is seldom optimised in terms of its overall economic impact on an operation. Blasting operations have evolved according to the environment provided by mine management. Most operations seek to minimise the unit cost of each component process (overburden removal, blasting, excavation and transport, crushing or grinding) without recognising the impact that blasting performance has on subsequent activities. The creation of æcost centresÆ or æmanagement unitsÆ that isolate blasting from its downstream impacts reinforce this trend. Modern blasting technology is regarded as sophisticated by virtue of the mechanical design of the drills, the chemistry of the explosives and the flexibility and reliability of modern blast initiation systems. However, blast performance is controlled by the nature of the rock mass and there is generally an inadequate appreciation of how blast designs should be tailored to suit different rock mass conditions or to meet different blasting objectives. Most operations utilise a limited suite of standard designs without routinely tailoring designs to suit the actual conditions at hand or the objectives of each blast. Mining operations would benefit from tackling the following specific challenges:What is the appropriate target performance for blasting operations to generate the maximum economic benefit for the operation as a whole? How should designs be configured to suit the changing rock mass conditions and operating constraints? What compromise (if any) should be allowed from the ideal to assist conflicting scheduling or other operational requirements? How can blast performance be measured and reported to provide appropriate guidance to future operations? These challenges can be tackled through the process of æblast engineeringÆ. This paper discusses the potential impact of blasting performance on the economics of mining operations and the author argues that very considerable benefits over and above those currently being achieved could be realised by improving the routine engineering of mine blasts. The paper then explores how the industryÆs failure to recognise the economic importance of blasting has resulted in the engineering of blasting operations receiving less management and technical support than is appropriate. Finally, a simple approach to the engineering of routine blasting operations is described as an example of how these challenges can be tackled.

Jan 1, 1999

By Standish N

The heterogeneous reactions of carbonaceous materials with oxidising gases are basic to all combustion phenomena and to many gasification processes. The carbon- carbon dioxide reaction at elevated temperatures (Reactivity) plays important roles in many metallurgical operations like iron blast furnace and ferro-alloys smeltings, zinc and lead smelting, alumina reduction, cupola operation and direct reduction processes. The stoichiometry but not the mechanism of the reaction between CO2 and carbon is represented by the equation (Boudouard reaction) CO2 + C 2CO (1) This reaction is more complex than that between carbon monoxide and metal oxides, which involves essentially a transfer of oxygen from the oxide to carbon monoxide to generate carbon dioxide without any change in gas volume, whereas the volume of the product gas of Equation (1) is twice that of the reactant gas. In the present paper an attempt has been made to review critically the reactivity measurements of various carbonaceous materials in carbon dioxide atmosphere. Steps in C-CO2 reactions, surface reaction mechanism, role of mass transfer on reaction kinetics, dynamic oxygen exchange reaction and rate equations and rate controlling steps are discussed. Various methods of reactivity measurements with their pros and cons are also presented. Effects of pertinent process variables on the reactivity of carbon are also described in detail.

Jan 1, 1986

By Lauricella P. F, Hendri D

In the Mesel sediment-hosted disseminated gold deposit, the spatial distribution of hydrothermal alteration is controlled by steeply dipping faults and shallowly dipping lithologies. Hydrothermal alteration of carbonate rock is characterised by decalcification, dolomitisation and silicification. Intense argillic alteration occurs in a laccolithic andesite intrusion adjacent to decalcified and silicified carbonate units. Sulphide minerals (pyrite, realgar, orpiment, stibnite and cinnabar) accompany hydrothermal alteration and precious metal mineralisation. The trace elements Ag, As, Sb and Hg are zoned spatially throughout the deposit. Mesel contains a mineable gold reserve of 7.8 million tonnes at 7.3 g/t Au. Gold mineralisation is preferentially localised in carbonate rocks adjacent to and beneath the andesite intrusion. The ore body consists of a central, near-vertical, high grade "feeder" system flanked by tabular, inward dipping, moderate grade "ouflow" zones. Mineralisation is controlled predominantly by two steeply dipping faults with high grade (>10 g/t) gold zones centred about structural intersections and fault splays. Gold is submicron size and locked in very fine grained (

Jan 1, 1995

By C Kocsis, G Baiden, Y Bissiri

CANMET-MMSL and Penguin Automation Systems Inc have been exploring how process simulation and ventilation modelling software, when combined, can be used to optimise hard-rock/metal mine ventilation systems. In combination, it is anticipated that this methodology will facilitate the exploration of mine design options that affect ventilation requirements and ultimately cost. Such integrated mine design could limit, and possibly reverse, the drivers that under current practices would generally dictate increased ventilation, power consumption, cost and greenhouse gas emissions. It is believed that the mining industry needs such process models to develop better business cases. For example, the implementation of optimised ventilation systems will undoubtedly require significant investment and mines are often reluctant to try such conservational measures unless they can be proven cost-effective. In general, Canadian hard-rock mines know their ventilation systems are providing too much air and consuming power unnecessarily. This is because their systems are designed to provide maximum production flexibility, based upon peak demand, which may be at some future time, and operated continuously at that level regardless of actual need. Simplistic analyses have shown electrical energy savings can range from 30 per cent through to 90 per cent (Hardcastle, Gangal and Leung, 1998). These savings depend upon such factors as the intensity and continuity of the production schedule as opposed to non-productive time. Where these savings occur is also important, if limited to either the primary or auxiliary ventilation systems, they could be negligible in a mineÆs total energy consumption. The problem these mines face is determining what level of ventilation is required in real-time and then the relative benefits. Such parameters as varying electricity costs, heating fuel options, different design criteria and their complex inter-relationship can effect the selection of an optimal system, depending on whether energy, environment or cost is the prime driver. The use of process simulators in underground mining is in its infancy; to date they have been used to show the benefits over the life of a mine under different mining methods, such as a comparison of tele-remote mining from surface against conventional manned operation (Baiden, 2000). This ongoing development advances the use of such simulators into a new and potentially important area, namely modelling the life-cycle ventilation requirements of a mine. This paper shows how such a life-cycle analysis as opposed to peak demand can provide the basis for optimising the design of ventilation systems and their control.

Jan 1, 2005

The Telfer Gold Mine, owned and operated by Newcrest Mining and located in Western Australia, is currently being expanded. A new underground sublevel cave development is proposed along with an appreciable expansion of the open pit. The Telfer area is generally subject to low rainfall, however, during the wet season cyclonic events can result in sizable rain events, which have the potential to cause substantial inflow. In addition to this, during the first five years (nominal) of the mineÆs life, there is the potential for drainage paths between the pit and the underground mine via decommissioned underground workings which lie directly under the pit. After this initial five year period the pit floor will be mined out below the old workings and will therefore no longer connect to the underground, however cave breakthrough to the surface may start to occur thus providing another water path into the underground mine. To arrive at an optimum, safe solution for dewatering the mine that successfully addressed the above items, a rigorous risk analysis was included as an integral part of the design process. This involved the determination of the probability of events occurring and the consequences of these occurrences. This was compared against the cost of mitigation for the various events. This paper outlines the process by which a safe concept addressing all the issues relating to dewatering the proposed mine has been arrived at. This process included: Establishing the pit catchment areas. These were based on historical run-off data and took into account practical mitigation works. Establishing an Average Recurrence Interval (ARI) based on reference material and historical rainfall data. Utilising a standard approach based on Australian Rainfall and Run-off (ARR) to calculate pumping and storage requirements for the various catchments. Analysing the 20 years of recorded rainfall in the Telfer area to establish the duration, magnitude and sequence of events. This analysis assisted in determining the surface run-off coefficient. Establishing potential water storage areas and determining the risks associated with using particular storage options. Establishing the percolation rate through the cave zone. A degree of uncertainty regarding the percolation rate in the cave zone required that the consequences of using various percolation rates were considered to aid in establishing the rate which was adopted. Establishing preliminary concepts and determining the most economically viable concept. Conducting a risk assessment based on the principles outlined by Australian Rainfall and Run-off (ARR) to confirm that the appropriate Average Recurrence Interval (ARI) had been selected. A risk assessment was also conducted in accordance with client requirements. Establishing the optimum pump station sizes and storage capacities. Establishing the appropriate numbers of duty and standby equipment. By using the foregoing process, which included a number of stages of risk analyses, an optimum dewatering system concept was produced.

Jan 1, 2003

By N Weatherstone

A consistent and reliable international approach to public reporting of a mining companyÆs main assets, its Mineral Resources and Mineral Reserves, has become of increasing importance in recent years with the rapid globalisation of the mining industry. Through the efforts of the Committee for Mineral Reserves International Reporting Standards (CRIRSCO), a committee representing national resource/reserve reporting committees in Australia, South Africa, UK/Ireland/Western Europe, Canada, USA and Chile, the reporting standards in most æwesternÆ countries use almost identical resource and reserve definitions and are generally around 90 - 95 per cent compatible. New codes based on the CRIRSCO model are being developed or considered in other countries, including Peru and the Philippines. This unified approach has provided the mining industry, regulators and investors with a common framework to report and interpret mineral resource and reserve estimates, thereby facilitating funding to the mining industry through improved investor understanding and confidence. The common reporting standards are reflected in the CRIRSCO International Template, available on CRIRSCOÆs web site, a document that is kept æliveÆ by reflecting the best of the most recently published CRIRSCO-type national standards. In a significant exception to this unified industry approach, the USA Securities and Exchange Commission (SEC) requires adherence to its own standard, only partly compatible with CRIRSCO-type standards, with adverse and costly implications for companies listed in the USA. A major industry submission was presented to SEC in April 2005 which, if accepted, would bring about considerable compatibility of CRIRSCO and SEC standards. The UN Economic Commission for Europe (UN-ECE) has, since 1992, been developing its Framework Classification (UNFC) as a single global system for harmonising all existing national and international resource/reserve reporting systems, covering both government and industry requirements and both the hydrocarbon and solid minerals sectors. While few mining companies report their resources and reserves using the UNFC, the system is accepted or is being examined as a basis for reporting by some governments, including those of Russia, China and India. The UN-ECE agreed in 1999 to incorporate CRIRSCO definitions into the UNFC for those categories of resources and reserves used for market-related reporting, but a more recent edition of the UNFC removed or changed the definitions, requiring re-engagement by CRIRSCO to ensure compatibility. Since 2005, CRIRSCO and the Society of Petroleum Engineers (SPE) have been involved in discussions with the International Accounting Standards Board (IASB), which plans to develop a new Accounting Standard for the Extractive Industries as part of its International Financial Reporting Standards. At the request of the IASB, CRIRSCO and SPE have been examining any potential for convergence of resource/reserve definitions between the mining and hydrocarbon industries. Each of these systems is described in this paper and high level comparisons made.

Jan 1, 2006

By J C. Diaz, C R. Scherpenisse

Blasting represents one of the most relevant unit operations in the process of mineral extraction. The final objective of this operation is that of obtaining an adequate final fragment size distribution such that the combined costs of drilling, blasting, excavation and transport, and crushing/grinding, are minimised, while at the same time producing the minimum possible level of damage to the surrounding rock mass. The strong influence that drilling and blasting has over the subsequent processes involved in the operational cycle makes it imminently desirable to have access to experience and technology which make possible the evaluation and optimisation of this unit operation. The correct use of vibration monitoring techniques offers a number of benefits in terms of their ability to examine any blasting process in detail. In effect, the measurement of particle velocity levels that result from the detonation of each explosive charge offers a means by which it is possible to measure relative efficiency of each charge, interactions (productive and counterproductive) between adjacent charges, and a definitive indication of general performance of any given blast design and its implementation. In this way the monitoring of blast vibrations in rock due to the blast event, can be used as a diagnostic tool, given that the correct interpretation of the vibration traces allows the determination of the level of interaction between the design and operational variables of the blast event. This makes it possible to evaluate, for example, the presence of out of sequence detonations, statistical scatter in the detonation times of pyrotechnic delay detonators, deficient detonation of charges, instantaneous detonation of charges and sympathetic detonation of charges, as well as the general of vibration levels in terms of peak particle velocity, acceleration, and displacement. Another important use of such data is in the construction of a database relating vibration levels to charge weight, hole diameter, and distance, for any given rock type, enables the calibration of predictive vibration models which in turn make it possible to predict the damaging effects of blasting. Knowledge of both the vibration levels induced, combined with quantitative measures of the geomechanical competence of a rock mass make it possible to estimate the probability of producing blast induced damage. The high levels of vibration generated by some blast events may damage the rock mass, producing new fractures or extending and dilating existing fractures. The vibration in this context may be considered as a dynamic stress provoking strain in the rock mass. This paper describes the application of the vibration monitoring technique, particularly in the underground mining environment, and its importance in diagnosis, modelling, control, and optimisation of the development blasting process. The potential of the technique is assessed in the context of achieving substantial techno-economic improvements development blasting results, increasing output whilst minimising the operational costs of the mining process.

Jan 1, 1999

Copper entering a lead ,smelter in concentrate or from other sources is recoVered as matte and speiss which contain appreciable quantities of lead. The matte and speiss are usually sold to copper smelters to recover the copper content and also any gold and silver in these products, but the value of the lead is largely lost. Some copper plants pay for portion of the lead content, but regarded as a means of recovering lead it is more costly and less efficient than if the lead were recovered at the lead smelter.Because of the value of this lead loss, the metallurgy of copper recovery has assumed greater importance in recent years owing to the rise on the price of lead.Two processes are in use today to produce matte and speiss, namely the iron matte process and the soda matte process developed by the American Smelting and Refining Co. 1 in D.S.A. The latter process is characterised by a higher copper to lead ratio than the older iron matting process.The following analyses are typical of matte and speiss produced at Broken Hill Associated Smelters, by both processes, although the soda matte process is still in a developmental stage and experience indicates that matte and speiss of lower lead tenor can be produced under favourable conditions.

Jan 1, 1951

By Till M, McGee WA

The Hermit Islands are situated at 145¦ E 1 30'S in the Bismarck Sea approximately 200km WNW of Manus Island. They are dominated by basalt flows, one of which yielded a K/Ar isotopic date of 3.4 + 0.05Ma. All basalts examined were olivine-bearing, but one sample also contained hornblende. Although many outcrops were weathered, no evidence of pervasive hydrothermal alteration was observed on any islands and non-weathered rocks are petrographically fresh and many retain glass.

Jan 1, 1990

By Mining Geophysics

Modern geostatistics has eliminated much of the guess-work in ore reserve estimation, and can calculate levels of confidence for the reserve estimate. Geological modelling software has brought about a revolution in the communication of complex geo-variables to mining engineers, metallurgists, surveyors and managers. Mine planning and scheduling can now avail itself of a veritable toolbox of enabling technologies.

Jan 1, 1994

By Okura T, Hino J

Coal utilization for copper flash smelting in Japan was initiated due to the sudden upheaval in the price of oil in the last ten years. A major portion of the heavy fuel oil has already been replaced by coal resulting in a corresponding decrease in energy costs. In addition to energy cost savings, an interesting metallurgical phenomenon was observed in flash smelting operations. Unlike oil combustion, coal is not burned completely in the shaft. A considerable fraction of coal particles remain on the surface of slag and are burned at the settler. Chemical investigation has shown that oxygen potentials at the settler have consequently decreased, bringing the slag and matte phases into reducing conditions, thus oxidation and reduction can coexist in one flash smelting unit. As a result, a decrease in magnetite and copper contents in the slag, elimination of furnace hearth build-up and dissolution of intermediate layer between matte and slag have been observed. In general, these led to improvements of furnace operations. However, thermodynamic investigations have shown that some minor elements such as As, Sb, Bi and Pb concentrate from slag to matte. Results evaluated on the basis of thermodynamic data relatively agree with practical observa- tions. Consequently, for coal utilization in flash smelting operations it will be necessary to control oxygen potentials from the stand- points of copper loss in slag and minor element Distributions.

Jan 1, 1987

By D Lau

Traditionally X-ray diffraction (XRD) has not been significantly used by the cultural heritage sector, as the most commonly used technique, X-ray powder diffraction (XRPD), requires sample removal from the artwork or artefact, followed by grinding of the sample to a fine powder. With the development of micro-X-ray diffraction (micro-XRD) and other associated advances, non-destructive, in situ analysis of crystalline pigments on micro-areas of paintings and artefacts has become possible. This is illustrated with the application of this technique to the in situ analysis of propriety paints, paint cross-sections and small paintings. However, workers have noted that XRD can be insufficiently sensitive with pigment mixtures, due to matrix effects. This study obtained X-ray diffractograms of 17 single pigment preparations and determined relative amounts of crystalline content. The purity of single pigments was compared with Joint Committee on Powder Diffraction Standards (JCPDS) database diffractograms. The impact of pigments with high X-ray absorption coefficients on the detection limits of pigments with low X-ray absorption coefficients was further investigated by building on work done with the chromium oxide-zinc oxide series with the preparation of a second series of binary mixtures of zinc oxide (which has a high absorption coefficient and is almost fully crystalline) and ultramarine blue, which has a lower absorption coefficient but which is more crystalline. Semi-quantitative analysis, where baseline and absorption factor corrections are made, confirm detection limits as low as five per cent for chromium oxide and ultramarine blue when in a binary matrix with zinc oxide. However, this type of analysis is very time consuming. So in order to theoretically simulate issues that will be encountered with binary pigment mixtures, the single phase diffractograms were used to theoretically investigate the matrix effects of the three white pigments with the various coloured pigments. This illustrated that detection limits can be as low as five per cent or in non-ideal conditions, such as with partial peak clashes or where there are large differences in relative peak intensity, as high as 50 per cent. These results have significant implications for the analysis of painted surfaces on artworks or artefacts. It has been demonstrated that ideally this method is more suited to the investigation of surfaces where there is minimal mixing of pigments or where there is not a significant difference between the absorption coefficients of the mixed pigments.

Jan 1, 2008

By Miller D. R

The mineral exploration and extraction industries have gained major cost and efficiency benefits from the use of computers. However these industries are now at a cross-roads with two seemingly disparate developments - that of an increasing number of complex geoscience databases and, at the same time, the merging of all known data for the particular regions at minimal cost. These two developments can be managed by the development and of an industry accepted geoscience data model and dictionary. This will provide a common basis of understanding for geoscience data through a common language and a common structure for geoscience information. Integration of specialist systems and databases can then proceed efficiently. The development of a data model is going ahead with consensus from the mining industry. This is a joint government and industry funded project and managed through the Australian Mineral Industries Research Association, AMIRA. AMIRA is a well known research broker to the Australian mining industry obtaining sponsorship for projects both from private and government groups. The AMIRA project, P431, called the Geoscience Data Model, is to be the Australian standard data model for geoscience disciplines. The requirement for a standard geoscience data model has been recognised in Australia for some time. In October 1991, the Australian Government Geoscience Database Policy Advisory Committee (GGDPAC) established a Geoscience Data Standards Working Group which drafted a comprehensive list of data categories of the geoscience area. An AMIRA project called AMDEX was established to develop a transfer standard for the mining industry data at about the same time as this committee was in operation. The first AMDEX sponsors meeting was held in May 1991. It was proposed to use the US Spatial Data Transfer Standard (SDTS) as the basis to transfer mining data in AMDEX. A limited data model of mining data to be transferred was developed for the AMDEX standard under SDTS. The Australian Geological Survey Organisation (AGSO) saw the need to extend this and develop a complete data model for the geosciences and proposed this as a new project to AMIRA. This was strongly supported by GGDPAC which lead to sponsorship of the project from most state geological surveys. The Geoscience Data Model can be broken down into separate data models for a number of geoscience themes and sponsorship obtained so far will enable models to be developed for a comprehensive set of themes selected by the project sponsors. Further sponsorship is required to enable a more complete coverage of the geoscience area to be developed. Sponsorship for the Geoscience Data Model has been strong from the geological surveys and there was some effort by GGDPAC to promote the project in these organisations. An Australian geoscience data model is of immediate use to the geological surveys in assisting the standardising of huge quantities of geoscience data held by government agencies and it is preferable that this be an Australia-wide standard.

Jan 1, 1995

By D Schwab, R M. Tosdal

The Quesnell-Stikine arcs, in the Canadian Cordillera, are host to Triassic and Early Jurassic alkalic porphyry Cu-Au and calc-alkalic porphyry Cu-(Mo-Au) deposits formed outboard of ancestralNorth America in island-arc tectonic settings (McMillan, 1991). The majority of the alkalic porphyry Cu-Au deposits are products of a discrete magmatic event at the end of the Triassic, with a second and smaller event in the Early Jurassic (Mortensen, Ghosh and Ferri, 1995). Of the Triassic complexes, the Galore Creek alkalic intrusive suite is one of the largest and most silica-undersaturated intrusive complexes, and host to the most significant undeveloped alkalic porphyry Cu-Au resource in North America (Lang, Stanley and Thompson, 1995). Because of the common presence of feldspathoidal-bearing rocks in the complex (Enns et al, 1995), Galore Creek likely represents an end member example of the alkalic porphyry Cu-Au class. The Galore Creek alkalic Cu-Au-Ag porphyry district, located in NW British Columbia (Canada), contains 12 mineralised prospects (Enns et al, 1995; Micko et al, 2007; Schwab et al, in press) with a total measured and indicated resources of 785.7 Mt at 0.52 per cent Cu, 0.29 g/t Au and 4.87 g/t Ag (NovaGold Resources Inc, February, 2008). The Central Zone is the largest and best delineated. Other economically important mineralised centres include the South-West, Bountiful, West Fork and Junction deposits. The South-West Zone, the focus of this contribution, is a Cu-Au-Ag breccia-centred deposit with a measured and indicated resource of 69 Mt grading 0.42 per cent Cu, 0.69 g/t Au, 2.67 g/t Ag. Hosted in brecciated intrusive rocks, the South-West Zone is distinctly younger than the Central Zone and most of the other mineralised centres (Enns et al, 1995; Schwab et al, in press). The South-West Zone therefore preserves the late stages of hydrothermal evolution at Galore Creek. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

In 1989 Henry Fairlie wrote a cover story for The New York Republic, 'Fear of Living'. He noted, `The first Apollo space craft caught fire during a test on the launch pad. Three astronauts were killed, the nation was shocked and horrified, all the more because the screams and scrambles of the astronauts could be clearly heard'. After a brief delay in manned flights, the Apollo program resumed with strong public support; within 18 months, Apollo 11 landed on the moon. Fairlie contrasts the Apollo tragedy to the 1986 Challenger disaster. `The prevailing mood in America so panicked NASA that it took almost three years to send up another shuttle', he observed. `In 19 years between these tragedies, the idea that our individual lives and the nation's life can and should be risk-free has grown to be an obsession threatening to create an unbuoyant and uninventive society.' Taking risks is a normal part of our daily routine. The act of living involves minute-by-minute decision-making focused on survival through the practical management of risks. The act of breathing exposes each individual to the risk of infection while the act of crossing the road could almost be considered suicidal. We deal with these constant threats by observing simple rules of hygiene, safety or what may be labelled as common sense. The rules of community, designed to minimise risk in society, can at times lose focus and result in the imposition of schemes that have a far greater cost than the issues from which they protect. Effective management of risk, whether in the community or a business is about awareness and balance and the elimination of unacceptable risk. Risk cannot be eliminated from our lives or our working environment. However it can be managed if it is properly understood, monitored and controlled. The purpose of my presentation today is not to provide a comprehensive technical risk inventory but to capture the essence of risk and the application of management strategies designed to deal with it in a positive fashion. The basis of our differential financial reward system is risk. The key to successful management is to deal with the downside risks in such a fashion that the benefits of enterprise are not eliminated. The key question any investor must consider is `can the major risks assQciated with a venture be managed or eliminated while retaining a greater proportion of upside potential'. The answer to this question is the ultimate value an investor would assign to any project. In reviewing the relevance of risk to our industry the range of papers to be presented today provide examples of how management deals with specific components of risk. In each case the value of the business has been enhanced by the practical application of balanced risk management. The ultimate success of the industry depends very much on this concept as it also provides a public showcase upon which we are judged. Therefore, from all perspectives the effective management of risk is a cornerstone from which to build a stable and progressive mining industry.

Jan 1, 1994

By F A. Roddick, C Swaminathan

As remaining gold deposits tend to become more refractory, some form of oxidative pre-treatment involving hydro or pyrometallurgy is necessary to maintain high metal recoveries. These pre-treatments include pressure oxidation, bio-leaching or roasting. In the past, the primary criterion for selection of oxidative pre-treatment relied mainly on the extent of gold recovery and relative economics. In this study, a different approach has been adopted, ie the quantitative determination of environmental performance of the oxidative pre-treatment processes bio-leaching, roasting and pressure oxidation to assess which had the least impact on the environment. By establishing the environmental performance of processes, waste minimisation can be addressed early in process selection. Using mass balances, the environmental theme method was applied to determine the performance, on the basis of gold treated, of the oxidative pre-treatment processes of selected plants. No clear trend was observed in the overall impacts of each of seven plants, with all but one of the environmental evaluation indices being of the same order of magnitude; this was probably due to masking effects arising from the large variations in feed composition, tonnage, and gold levels. Within each type of pre-oxidation plant however, certain trends were detectable. For instance, irrespective of plant size, ore composition or mineralogy, for the bio-leaching and pressure oxidation units, the general order of environmental impact from greatest to least was sequentially toxicity, acidification potential, depletion of resources, solid waste generation and greenhouse enhancement. For the roasters the acidification potential was the most significant. Determination of the environmental performance of the oxidative pre-treatment of a hypothetical ore in a plant of fixed tonnage was undertaken to remove the possible masking effects of variables associated with feeds of different mineralogy, gold tenor and tonnage. The bio-leaching process gave a marginally better performance than pressure oxidation, the roasting process the worst, although there was not a great difference between them. The decreasing order of contribution to the environmental index was acidification potential, toxicity, resource depletion, solid waste generation and greenhouse enhancement for bio-leaching and pressure oxidation; whereas it was acidification potential, solid waste generation, toxicity, resource depletion and greenhouse enhancement for roasting. Since the major contributor to the environmental index was the acidification potential, the environmental performance of treatment processes for the acidic effluents was calculated. After neutralisation of the net acid resulting from bio-oxidation and pressure oxidation, and the application of various scrubbing and product formation processes for the sulphur dioxide from the roasting process, it was shown that pressure oxidation gave a marginally better performance than bio-leaching, ahead of roasting. This study demonstrated the potential for the development of a predictive tool which could be used in determining the environmental performance, and thus the selection, optimisation, and improvement of pre-oxidation processes for least impact on the environment. These would allow operation of these processes within defined environmental performance limits and decisions regarding the desirability of processing various parts of a heterogeneous orebody to be made on environmental grounds.

Jan 1, 2000

By Paton T. P

In the technical sense, as well as in the professional sense, the word 'model' can have many meanings. More than 23 000 references were uncovered by a simple literature search on keywords ' MO D EL#. and. (META LLURG#. or. M I NERAL#)' . For the purpose of this paper, 'models' will be considered to be mathematical formulations which attempt to represent or approximate a process. The model may be purely, or a combination of: ò fundamental models, based on the laws of physics, chemistry and thermodynamics; ò semi-empirical or phenomenological models, where an intuitive concept of the process is formulated and found by testwork to fit observed behaviour; and ò empirical or 'black-box' models (including neural networks), where a mathematically convenient form is proposed and fitted. Even under this more restricted definition, which eliminates heuristic and statistical 'models', it is clear that the efforts expended in devising and using models have exploded during the years since the first APCOM Conference in 1961, benefiting from the dramatic decrease in the cost of computer power. This paper reviews the areas of usage of computer modelling in the metallurgical and mineral processing industries, from plant design, through off-line support, to on-line modelling and automatic control. In each area, frontiers of new development of the technology are mentioned. It is noted that, while modelling is now standard practice in design, it is not yet the norm in operating and controlling plants. The reasons for this partial acceptance are, it is argued, less related to the limitations of the technology than to the human and organisational factors involved in transferring technology to implementation.

Jan 1, 1995

By G W. Wilson

Rehabilitation of tailings impoundments is one of the most challenging aspects in mine closure, as not only does the potential for producing leachate pose a challenge to the rehabilitation designer, but also other aspects such as stability and settlement must be considered. The water balance of a tailings impoundment is unique in the sense that it usually hosts a pond that in turn causes a phreatic surface in the impoundment. The position of the phreatic surface defines the saturated and unsaturated zones in the impoundment, which of course varies spatially and temporally. Predictive modelling for this hydrologic system becomes difficult, as numerical models capable of analysing the combined saturated/unsaturated zones are not adequately refined to accurately solve the flux boundary problem for infiltration at the surface of the tailings. This paper describes the development of a flux boundary model that enabled accurate modelling of the unsaturated zone in the tailings impoundment at Kidston Gold Mine, Queensland, Australia. The technique made it possible to accurately predict the spatial variation of infiltration to the tailings as a result of the presence of the phreatic table. The conceptual model defines the boundaries for the Kidston tailings dam, based on a generalised cross-section through the dam. Firstly the shape of the top boundary is described as a function of the particle size of the tailings associated with particle segregation that occurs due to the hydraulic placement of tailings. This function was rigorously tested using in situ infiltration tests and laboratory materials testing. Defining the bottom boundary of the section, ie the phreatic level was done by physically monitoring the phreatic level with 42 piezometers strategically located on the tailings dam. Analysis of this data led to the fixing of this bottom boundary through the introduction of a function that mimicked the shape of the phreatic level. The material properties of the surface layer, specifically the saturated permeability that would govern the infiltration/exfiltration rates of moisture through the top boundary layer were defined on the basis of extensive field and laboratory material testing. A function for the saturated permeability was developed on the principles of particle segregation. Finally a procedure is described for the application of the new conceptual model for the evaluation of the spatial infiltration to a tailings surface using the rigorous one dimensional surface flux boundary code SoilCover. The solution of the calculation described above was then used as the top boundary condition in conventional three dimensional saturated/ unsaturated flow codes, and verified against measured seepage rates from the tailings impoundment under drains. It was concluded that the developed spatial flux function was in deed a most rigorous representation of reality. Although the methodology presented here was applied to the Kidston tailings impoundment only, the authors believe that the principles are directly transferable to any tailings impoundment that has a varying phreatic zone thickness due to the presence of a pond. The mathematical equations describing the typical cross-section would be site specific, but the approach and ultimate solution methodology would be directly transferable.

Jan 1, 2003

The major incentives for developing continuous processes for the production of formcoke are to achieve a wider range of coals which can be used, greater operating flexibility enabling the production of various coke qualities, and environmental improvements. The characteristics of a formcoke which must be considered when assessing its performance in the blast furnace are compressive strength, abrasion resistance, volatile matter, reac- tivity, porosity, density, size, shape, ash yield and sulphur content. Lurgi's development work in attempting to pro- duce a formcoke which meets the specified requirements has resulted in most current efforts being concentrated on the Bergbauforschung/Lurgi hot briquetting process. This process blends hot char produced from a non-caking coal with small quantities of caking coal in a special mixer in the plastic range of the caking coal. The material is subsequently briquetted hot, then subjected to a thermal after-treatment to produce a strong abrasion resistant formcoke. A 650 tonne per day plant for British Steel Corporation is now under construction. A study of the equipment requirements and the operating costs indicate that the economics of large scale formcoke plants compare favourably with those of conventional coke-making plants.

Jan 1, 1975