Search Documents

By Isabel C. B Rodrigues, Flávia D. Reis, Versiane A. Leão, Rosa M. F. Lima

Attention has been focused in recent decades upon the precipitation of metal sulphides from acid mine drainage (AMD) and pregnant leach solutions, due to the advantages of the sulphide precipitation process over traditional methods employing hydroxides. The aim of this work was thus to explore technologies for copper precipitation using either Na2S or biogenic sulphide. The recovery of copper sulphide was improved when the initial pH of the solution containing each metal was 4 or excess sulphide was employed. In such, a condition the removal efficiency was 99.9%, corresponding to a residual level of 0.1mg/L for copper in solution. Kinetic parameters for precipitation were determined from the particle size distributions using the method of moments, where the growth and nucleation rates, as well the agglomeration kernel, were calculated. The biogenic sulphide was a suitable alternative to sodium sulphide for copper removal as either sodium sulphide and biogenic sulphide can be utilized to precipitate such a metal allowing the effluent to be compliant with environmental legislation.

Jan 1, 2014

The Daly-Judge Tunnel, begun in 1887 to drain mine workings, is now a source of potable water for the Municipality of Park City. The water is exceptionally clean; however, when roof falls occur, suspended solids levels become too high and water from the tunnel cannot be used in the treatment plant. In 2001, the tunnel was inspected and rehabilitated to ensure that the water supply for the 2002 Winter Olympic Games would be uninterrupted. Twenty-five timber tunnel sets were removed, and 86 steel sets were installed. Timber lagging was installed or replaced over about 230 m (750 ft) of tunnel length.

Jan 1, 2006

By M. Yao, D. Thibodeau

"Selective mining, such as post pillar cut and fill, is used in large, flat, irregularly shaped ore bodies where ground stability is to be maintained. This selective mining is used to open the stope to the full lateral extent of the ore body in order to minimize the dilution and maximise the recovery. For increased mining depth, design of the post pillar becomes more challenging since those pillars will eventually fail as mining progresses upwards. The post pillar should be designed such that failure does not occur at the early mining stage, such as at the first cut. After mining progresses upwards, the post pillars are expected to fail but be confined by backfill. In order to maximise ore recovery, both drift width and post pillar size must be designed adequately with a consideration of all geomechanic parameters. This paper will describe the process used to design post-pillar cut and fill for one of the ore bodies in Vale’s Copper Cliff Mine using a combination of both empirical deterministic and numerical modelling techniques. By utilizing both empirical deterministic and numerical modelling techniques drift width and post pillar size can be effectively designed. Current post pillar cut and fill design in the existing Vale operations are used to validate the design for Copper Cliff Mine. INTRODUCTIONCopper Cliff Mine is located within the Copper Cliff Offset in the limits of City of Greater Sudbury, Ontario, Canada, as shown in Figure 1. The Copper Cliff Offset extends about eight kilometres south from the Sudbury Igneous Complex into the footwall rocks. Until 2008, the current Copper Cliff Mine was operated as two separate mines i.e. North Mine and South Mine. However, as part of restructuring of Vale Ontario Operations, the North and South Mines were merged in 2009 to form the “Copper Cliff Mine”."

Jan 1, 2015

By A. F. Banfield

"IntroductionELEMENTAL sulphur occurs in three types of deposits: in salt domes in the Gulf Coast region of the United States and Mexico, from which over 90 per cent of world native-sulphur production is obtained; in sedimentary deposits such as those in Sicily, which are thought by some authorities to contain the largest world reserves of elemental sulphur; and as surface deposits, associated now or in the past with some phase of vulcanism, the type which bas the greatest world-wide distribution.Deposits of the volcanic type are the subject of this paper.From antiquity until the successful development of the sulphur-bearing salt domes at the beginning of this century, important sulphur production for local needs was obtained from volcanic deposits in many parts of the world. Due to technical and economic factors, however, producers could not compete in price with sulphur from salt domes. •The result has been that, except in Japan and Chile, little sulphur was produced from volcanic deposits from about 1910 until the start of the Korean war in 1950. Shortly after the outbreak of the Korean war, an acute world sulphur shortage developed and prices skyrocketed in many countries up to several hundred dollars a ton. Interest in volcanic deposits was renewed and exploitation of many was undertaken. Few of these operations have been successful, mostly due to inability of management to solve technical problems.While important volcanic deposits of elemental sulphur have not been reported ( 1) in Canada, and it is doubtful that any will be found, data presented in this paper may be of interest to students of ore genesis.This paper is based on field examination of numerous deposits of the volcanic type in North and South America."

Jan 1, 1954

By Sylvie Lévesque, Cory Hennessey, Daniel Amariei

"In the iron ore industry, fine particles recovery is an important concern in terms of process performance and production costs. Continuous efforts are thus devoted to increase the efficiency in handling these fines.The Reflux Classifier (RC) is a relatively new technology that is mainly used in the coal and industrial minerals industries. The operating principle of this system is based on three mechanisms: hindered settling, autogenous dense medium and lamella settling. A preliminary evaluation of the Reflux Classifier technology for the beneficiation of iron ore fines was formerly done at the pilot scale using a RCTM300 unit. The good results obtained, using iron ore fines from screened spiral stream, made this technology very attractive for the iron industry. However, the high capacity of the RCTM300 unit (1–3 t/h), makes it unsuitable for R&D purposes. Thus, a smaller unit, the RCTM100, was assessed to validate the performances obtained with the RCTM300.This paper summarizes the performances obtained with the RCTM100. The challenges of the scale-down related to the adaptability of this technology to the iron ore industry are also presented. The results are compared to the RCTM300 performances, as well as benchmarked against sink-float tests. The metallurgical results on feed and products issued after the test work with the RCTM100 unit are supported by mineralogical characterization using a Mineral Liberation Analyzer.INTRODUCTIONFine particles recovery by physical separation means is a historical concern (Holland-Batt, 1992; Peukert and Wadenpohl, 2001; Srivastavaa et al., 2001; Majumder et al., 2003). Attempts to improve fine particle recovery at the laboratory, pilot and industrial scales adopting different strategies with traditional equipment or assessing new promising devices such as the MGS (multi-gravity separator), the Kelsey jig, the Yang jig, etc. (Kim, 2002; Goudreau, 2008; Kerr, 2012) have yielded variable success."

Jan 1, 2016

By Askari-Nasab, D. Checkel, K. Awuah-Offei

Life Cycle Assessment (LCA) is an emerging environmental management tool for examining environmental impacts from cradle to grave. In this paper, LCA is used to evaluate the acidification potential (AP) and global warming potential (GWP) of belt conveyors and truck haulage systems in a surface gold mine using the ISO 14040 standards. The results show that, for AP, the truck system has 32 kg of equivalent SO2 per functional unit, compared to 8 kg for the conveyor system. However, for GWP, the conveyor has 2,820 kg of equivalent CO2 per functional unit, compared to 648 kg for the truck option.

Jan 1, 2009

By Steven Doyle

Presentation Outline ?Introduction to Brunswick Mine ?Mining Needs and Drilling Trends ?Maintenance Program ?Back to Basics ?Results ?Additional benefits Introduction Xstrata Zinc Brunswick Mine ?No. 12 deposit discovered in 1953, pilot mining 1957, u/g mining began in 1964 ?Zinc, copper, lead and bulk lead/zinc concentrates ?Since 2007, a fully owned division of Xstrata Zinc Canada ?Over 132Mt milled 3.4 % Pb, 8.8 % Zn and 102 g/t Ag ?Deposit dips approximately 70 degrees; strike length of 1200 m; currently mining from 250 m to 1125 m depth

Nov 1, 2011

By Jason Berenyi

Presentation Overview ? What is Potash? ? Where are the potash deposits? ? Current potash mines ? production, capacity and planned upgrades ? Saskatchewan Saskatchewan?s Potash Production Potential s ? Current Status of Potash Exploration ? Increasing Demand for Potash ? Saskatchewan global role

May 1, 2009

By Zetti Gavelán

Globalization and the search for new ore deposits inevitably lead to investment in foreign markets. Investors need to be aware of the effect of their venture on regional, social and economic issues when they invest. Decades of detailed statistics from various sources can be integrated and analyzed to predict the social-economic impact of investment, thereby mitigating risk. To this end, the correlation among variables such as foreign direct investment into mining (FDIM), reserves, and socio-economic indexes is examined. The investigation focuses on South America from 1992 to 2000. Throughout the past decade, South America has benefited from capital investment from more developed countries. This huge investment by the mining industry has impacted the South American economies and can be measured directly using the FDIM. Other economic variables investigated include mining gross domestic product, direct employment, and human development indexes. The correlation is based on data compiled from the World Bank, international risk assessment agencies, the United States Geological Survey (USGS), and the information agencies of various South American countries. Initial analysis of the economic data suggests various expected outcomes. For example, foreign investors may disregard a measured, highly negative country risk in deference to the quality of its mineral resources. It is important to note that the standard measures of country risk published by investment analysts are not industry or investor-specific. In the case of the investor, the level of accepted risk is based on their managed investment portfolio. It is noted that arguments for level-playing fields may be the antithesis of globalization. The discovery and exploitation of ore bodies in a globalized environment necessitates the development of economic measures that standardize mining-specific risk variables and trends. The latest published information on the security of mineral investments in South America is investigated by integrating databases of economic, geologic, production, human indexes, and risk ranking.

May 1, 2003

By W. J. Weymark

"The Gregg River project is located 40 kilometres southwest of Hinton, Alberta, adjacent to and east of Jasper National Park. This metallurgical coal mine has been developed as a joint venture between Gregg River Coal Ltd. (a subsidiary company of Mana/ta Coal Ltd.) and seven Japanese companies. This 200-million dollar project consists of a conventional truckshovel open-pit operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. Mining operations started in October 1982 with plant start-up following in April 1983. Introduction This paper is an overview and update of the Gregg River project, a metallurgical coal mine being developed as a joint venture between Gregg River Coal Ltd. (a subsidiary of Manalta Coal Ltd.) and seven Japanese companies. The Gregg River Coal leases cover 3440 hectares and are located 40 kilometres south of Hinton, Alberta, adjacent to and north of Cardinal River Coal Mine (Fig. 1). This 200-million dollar project consists of a conventional truck-shovel operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. A total of 31.5 million tonnes of clean metallurgical coal will be sold to the Japanese over a fifteen-year term. At present, mining operations are ahead of schedule and the plant started up on schedule in April 1983. Access and Climate An all-weather road, Highway 40, connects the minesite with Hinton (the nearest commercial centre) and a Canadian National Railway (C.N.R.) spur line connects the minesite with the C.N.R. main line in Edson. Hinton is accessible by road chartered airline and rail. ' ~h~ rug~ed and varied topography in the area creates large vanations m temperature and precipitation over short distances. The region is characterized by precipitation throughout the year long cold winters and short cool summers. The mean temperatur~ of the area range from a low of -14°C in January, the coldest month, to a high of 12°C in July, the warmest month. Long-term precipitation data indicates a mean yearly precipitation of 870 mm of which 620Jo occurs during the summer months."

Jan 1, 1985

By Martin Lebeuf

The phenomena occurring in the cathode and at the cathode surface of aluminum electrolysis cells are very important in regards to cathode voltage drop and cathode wear. In the current study, laboratory-scale aluminum electrolysis cell cathodes were analyzed by X-ray microtomography. This technique allows an excellent visualization of the distribution of different substances, if their respective X-ray attenuation coefficients are different enough. In the current case, the important difference in the mean atomic number between cryolitic bath and graphitic carbon results in good contrasts. The volumetric bath penetration profile, porosity and impurities distribution in the cathode were thus obtained. Furthermore, metallic impurities and bath heterogeneities were observed at the cathode surface. Observations were also made with Scanning Electron Microscopy - Energy Dispersive Spectroscopy (SEM-EDS).

Jan 1, 2011

By Rob Assabgui

Presentation Overview ? Stobie Mine Sublevel Cave Background ? Elevated Silica Levels ? Silica Control ? Challenges and Issues ? Conclusions

Oct 1, 2010

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

By Matthew D. Meyer

SMART, an association of surface mining companies formed in 1995 to develop a coordinated approach to technology development for the mining industry, has recognized the need for the establishment of a worldwide database that continuously collects mining equipment data and provides metrics related to productivity and cost. Under the auspices of SMART, Syncrude Canada, Suncor Energy and Albian Sands Energy (three oil sands mining operations located in northern Alberta) have established a pilot project for mine benchmarking. This presentation will include a review of the pilot progress including: ???Data gathering techniques: means of collection and storage, proposed practice for data control and normalization, access to data/reports and format for data. ???Reports/analyses for individuals, across groups, within the total industry pool and publicly. ???Security and confidentiality of information belonging to identified parties. ???Sharing of best practices among members. SMART has identified two key deliverables to ensure success of the project. First, data supplied from surface mines must be validated and normalized to common definitions and then analyzed to provide participating companies with regular reports that allow them to understand their position and resultant opportunities to achieve world-class performance. This model maintains granularity of the data for each operation that can then be recombined into standard comparisons or specific indices as required. The general categories of: operating delays, maintenance downtime, standby, and scheduled downtime, have been used to frame comparisons. Second, participating companies are looking to go behind the indices to identify and share best practices that distinguish particular operations. The spirit of cooperation between the companies involved in the pilot project is meant to be a model for future expansion of the benchmarking project.

Apr 1, 2005

By Michael Samis

Conventional project valuation techniques, such as discounted cash flow (DCF) method, are more frequently being criticised for the manner in which they consider the interacting effects of uncertainty and project structure (including management flexibility) on project value. Modern asset pricing (MAP; often called ?real options valuation? when applied to the analysis of flexibility) is a more general valuation framework that corrects many of the shortcomings of common valuation methods. Previous mining applications of MAP have tended to treat the ore deposit as a homogenous entity. While useful for demonstration purposes, this is inadequate for practical application in industry. This paper presents a MAP valuation example that allows for the heterogeneous nature of an ore deposit. It shows that deposit structure may increase the complexity of the mine planner?s decision so that results of a standard DCF analysis, or a simple MAP analysis that ignores the details of deposit structure, are misleading. In the example, a management is considering the development of an adjacent low-grade zone while mining operations in a high-grade zone are ongoing. If the low-grade zone is developed before high-grade reserves are exhausted, the proposed development will include both low-grade zone development and a capacity expansion to handle additional low-grade reserve production. If development of these reserves is delayed until the high-grade reserves are depleted, then the low-grade reserves can be developed without a capacity expansion. A typical DCF analysis would reduce the management?s decision problem to three alternatives: 1) continue mining only in the highgrade reserves, 2) immediately develop the low-grade reserves and expand capacity, and 3) delay low-grade zone development until the high-grade reserves are exhausted. The model presented here allows the management to reconsider the development and capacity expansion decision on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably. The model presented here extends the ability of mine planners to describe actual project structure while using the MAP valuation framework that is already noted for its capacity to combine project uncertainty and risk insights with a dynamic project description.

May 1, 2001

By S. Balideh

A good understanding of the behavior of rock helps us to make more informed decisions regarding geo-structures. Engineers need accurate equations to calculate the strength and deformation of rock before and after failure. Previous studies explain the failure of rock to ultimate strength, and laboratory tests adequately determine the ultimate strength and deformation modulus of rock. However, there are few comprehensive equations to determine the post-failure strength and deformation of rock. Previous work shows that the post-failure behavior of rock depends on the behavior of the broken rock particles after failure. The following question is then posed: How can the post-failure behavior of rock be determined by the behavior of broken rock particles? In order to answer the question, this study pursues three objectives: (i) to explain the behavior of broken rock at low confining pressure; (ii) to estimate the behavior of broken rock via the extrapolation of scaled laboratory testing; and to suggest a procedure (iii) to outline the post-failure behavior of a rock mass at low confining pressure commensurate with the behavior of broken rock in a rock mass.

Aug 1, 2013

By W. S. Dyer

Introduction In northern Ontario, refractory clay is found on four rivers of the James Bay watershed: the Abitibi, the Mattagami, the Missinaibi, and the Moose. The clay all belongs to the same geological formation ( the Mattagami of Lower Cretaceous age) , and occurs within a structural depression or 'basin', the boundaries of which have never been defined but which appears to cover at least 1,500 square miles of territory. The recently constructed James Bay extension of the Temiskaming and Northern Ontario railway crosses the northeast end of the basin at the Onakawana lignite field, which by rail is 126 miles north of Cochrane, 605 miles north of Toronto, and 60 miles southwest of Moose Factory. Smoky Falls, the northern terminus of the railway owned by the Spruce Falls Power & Paper Company, Limited, is 7 miles south of one other point in the basin, i.e., the outcrops of refractory clay, sand, and kaolin at the foot of Long rapids on the Mattagami river. Smoky Falls is 50 miles north of Kapuskasing. In a very early report(l) , Dr. Robert Bell, of the Geological Survey of Canada, described '"light coloured marl in horizontal beds" from the Missinaibi river, and noted that the lignite also occurring in the river was probably :associated with the marls. This was undoubtedly the Cretaceous refractory day. Other early writers noted the occurrence of fire-clays, but it was not until Joseph Keele(2), of the Geological Survey, visited thee region in 1919 and studied the clays that their real significance was known.

Jan 1, 1933

By O. A. Ojo, D. L. Chen, N. Zhou, J. Q. Zhang, A. K. Khan

Dual phase (DP) steels are designed to consist of hard martensite dispersed in a relatively soft ferrite matrix, which offers a favorable combination of high strength with good deformability. Fiber laser welding (FLW) is becoming increasingly important for joining advanced materials due to its flexibility and deep penetration. In this study, the microstructure of a dual phase steel, DP980, welded by FLW technique was carefully analysed. Gleeble thermo-mechanical simulation coupled with analytical transmission electron microscopy (TEM) revealed that the FLW process produced significant microstructural changes in a narrow heat affected zone (HAZ) and fusion zone (FZ), which can result in dramatic changes in mechanical properties. This is reflected in the micro-hardness profile obtained across the welded material. The salient phase transitions induced by the FLW, including the formation of new martensite grains in the upper-critical HAZ and FZ, are discussed.

Jan 1, 2014

By J. E. Udd, S. Bharti

"ABSTRACTMonitoring of stability conditions in underground mines permits management to assess the response of the rock mass to mining strategies. Monitoring of movements, if sufficiently early, may also permit operators either to avert potential failures or to develop alternative approaches to extraction.The Falconbridge organization has been a leader both in the uses of rock mass stability monitoring techniques and in the development of instrumentation.In this paper, the authors review the Falconbridge approaches to monitoring, and present case history examples to illustrate the application of the various instruments used.RESUMELa surveillance des conditions de stabilité dans les mines souter-raines permet aux chefs d'enterprises d'évaluer les réactions de la masse rocheuse aux méthodes d'extraction minière. Si le contrôle des mouvements du terrain est effectué assez tot, l'exploitant pourra prendre les mesures qui s'imposent, soit pour éviter les détériorations possibles ou pour mettre au point de nouvelles méthodes d'extraction.Le groupe de la Falconbridge a ére le premier a utiliser des techniques de vérification des conditions de stabilité de la masse rocheuse et a mettre au point l'appareillage requis.Ce document présente une revue des méthodes employées par la Falconbridge pour assurer la surveillance active de la stabilité de la masse rocheuse et illustre au moyen de cas concrets la manière d'utiliser les divers appareils."

Jan 1, 1987