Search Documents

By Jose A. Caceres

Mine planning and mineral processing optimization are usually treated as two unconnected problems, especially at open pit and panel caving mines where the cut-off grade is practically the only variable optimized and analyzed for in the planning proposes. Using existing planning tool, the output is a reserve consumption strategy privileging higher grades. With the earlier consumption of the highest grades, every year produces revenues which are closer to the cost and potentially even below cost. However, there are other ore characteristics that can also affect the profitability of the operation. A new methodology has been developed, incorporating the grinding and flotation relationship into the mining economic models for the simultaneous analysis and optimization of the throughput-work index-recovery relationship through changes in the mining limits, sequence and redefinition of the reserve consumption strategy. A mine-site that implements this new planning strategy, can expect to increase the NPV from 5 to 15% depending on the actual operational settings. Two case studies have been developed, showing how the inclusion of the work index in the economic model changes the phase and mining sequence in an open pit mine and the caving sequence and the optimum column height in a panel caving mine.

May 1, 2004

By Karl J. C. Harries

This paper looks briefly at some of the agreements and types of royalties that may be met during exploration activities, but does not go into details relating to them. Agreements can either make or break a deal or relationship. A well drafted, comprehensive and fair agreement can create good relations and trust among the parties and will go a long way towards making a deal work. In the best of all worlds the agreement will be put away and not need to be referred to after it has been signed (but it will be there if needed to sort out potential problems). On the other hand, a poorly drafted agreement or one that is inappropriate to the circumstances or unfair to one of the parties can break a deal and end up with the parties facing each other in that expensive, unproductive and time-consuming occupation ? a lawsuit. Accordingly, it is advisable to involve professional advisers with any agreement. The straightforward one may involve no more that a read through whereas the more complex agreement will require considerable involvement. There is, however, one rule for every explorationist to remember: a professional adviser is only an adviser. His responsibility is to make sure that you have the necessary information to make a reasoned decision but the decision is yours, not the adviser?s. It is your deal, you are going to have to live with it, and it is inappropriate for an adviser to introduce new concepts or amend negotiated ones without your specific instructions. Mineral exploration agreements, although basically option, acquisition and joint participation agreements, come in all the shapes and forms, appropriate to give effect to the endless variety of deals negotiated by the ever-active minds of explorationists. You will note the reference to "joint participation agreements" rather than "joint venture agreements". The latter term was purposely avoided because, with the current activity of explorationists from common law jurisdictions in civil law jurisdictions, it has become necessary for the explorationist to become familiar with corporations and shareholders agreements. As most of you are no doubt aware, under the civil law system a joint venture is normally not recognized as a legal entity and, therefore, joint participation in projects is usually by way of corporations.

May 1, 2003

By Enrique I. Acuña

Creighton Mine is part of the mining history of Sudbury with more than 100 years of operation. Currently the deeper levels of the mine are reaching the 8000 ft level without implementation of mechanical refrigeration system as a result of the use of the Natural Heat Exchange Area (NHEA) over the past decades. The NHEA of Creighton Mine is part of an old block caving area divided into 4 blocks of trenches that were used to extract the ore. Currently, it is used year round to condition the outside temperature before the airflow enters the fresh air system of the mine. As the mine is progressing deeper, underground temperatures in the lower levels are starting to approach the limit of Vale?s guidelines for working in heat. This paper presents the study developed to improve the management of the NHEA to obtain cooler temperatures at the intake of the ventilation system and outlines the impact to the mine in terms of the additional level(s) that could be operated underground without the use of mechanical refrigeration. This is another of the efforts currently under development for energy conservation and to reduce the capital and operational costs of Creighton Mine while extending the expected life of the mine.

Oct 1, 2010

By J. E. Gebhardt

Advances in computational modeling provide unprecedented process simulation tools for the process engineer to examine and explore options for optimizing heap leach operations. A phenomenological model developed within a computational fluid dynamic software framework provides a general heap leach modeling tool that describes reactive dissolution and fluid flow through the stockpile. A one-dimensional form of the model is used to parameterize the kinetic leach reactions for a mixture of copper sulfide and oxide minerals against data from operational leach tests. A two dimensional version of the model provides a means to investigate the effects of irrigation rate, lift height, air injection, bacteria limitations, and other factors on recovery and pregnant leach solution concentrations. The model was calibrated for the Nifty Copper operation and ore type in order to simulate heap performance. Model simulations are reported for the chalcocitetype ore and compared to process data. The application showed that the multidimensional nature of heap leaching causes heterogeneous effects that are not always adequately described by one-dimensional models. Irrigation flow rate and aeration effects were simulated for a multi-lift heap section, and model results indicated that air injection at the base of the second lift would be required to achieve expected copper recovery under these lift height and flow conditions.

Jan 1, 2007

By T. Melfi, M. James

Attaining required mechanical properties in welds made using the double submerged arc welding (DSAW) process is difficult, and it is becoming more difficult as the strength level of the base materials continues to increase. Producing weld metal with adequate mechanical properties involves factors that are often overlooked and not taken into consideration. Not least amongst these problems is simply finding information to use in selecting the appropriate flux/wire combination. Most of the available data on flux/wire combinations provided by consumables manufacturers is generated using the multiple pass welding procedures required for classification per specifications such as AWS A5.17 and A5.23. This data really gives no insight into the properties that can be expected in a DSAW application. Also, base plate composition plays a very significant role because of the fact that base plate dilution can be as high as 70% in DSAW welds. This means that if any elements are present in the base metal that are deleterious to mechanical properties, they will also be present in significant quantities in the weld deposit. Some of these elements can decrease toughness and increase hardness (increased hardness is a concern if the pipe is intended for sour service). Some of these problems can be mitigated by proper selection of welding consumables. Selection of proper welding consumables means selecting an electrode that provides the appropriate alloying elements to obtain the desired level of impact toughness while also keeping the hardness within any specified limits. In order to attain the necessary impact toughness, selection of a flux with an appropriate composition (in terms of its basicity and its ability to control the nitrogen content of the weld deposit) is required. As with all welding processes, the mechanical properties of DSAW welds are also highly dependent on the welding procedures. This work clarifies how to select appropriate consumables to meet a given set of requirements, and also how to achieve the optimum mechanical properties from those consumables.

Jan 1, 2005

By Hans Lundberg

Magnetic methods have been used for more than three hundred years in prospecting for magnetic ores. More recently magnetic methods have been used for finding salt domes and studying certain geological formations. A number of instruments have been developed and substantial improvements made as to their sensitiveness and accuracy. Papers and articles written on magnetic methods are generally elaborate and technical, and the average prospector finds it difficult to obtain the necessary information as to how to operate the simple magnetic instruments to the best advantage. The miner's compass, dip needle, and inclinator are, indeed, very useful instruments and are easy to handle, and a great deal of valuable information can be gained if the instrument is properly operated and the results correctly interpreted. The lack of knowledge of the fundamental principles, however, has caused a great deal of disappointment. Other and more elaborate geophysical methods have recently come into the limelight, and the prospectors seem to have lost a great deal of interest in the dip needle. This is much to be regretted, because magnetic methods have a particular field of use. The present article is an attempt to help the prospector regain interest in the magnetic instruments and to show the use and application of a simple magnetic survey. If the prospector expects some useful help in his work, he must, of course, know the instrument, know how to take the readings, and know how to plot and interpret the observations.

Jan 1, 1929

Electric Vehicle Controllers Ltd. ?EVC started in 1981 ?Underground electric locomotive drive systems ?Developed tandem load sharing system and radio ELOS controls ?Locomotive autonomy systems ?Entered space technology development in 1999 with NORCAT to develop Mars drill for CSA ?Commercial distributor for drilling systems, lunar physical simulants, electric mobility systems and lunar mining technologies

May 1, 2009

By Bruce Peberdy

Outline ?Building Systems ?Climatic Effects ?Thermal Effects ?Building Components ?Building Materials ?Structural Deterioration ?Maintenance Considerations

Nov 1, 2011

By A. M. Christie

Acknowledgements The following account has been compiled mainly from records and maps of Eldorado Mining and Refining (1944), Limited, hereinafter called the Crown Company. This work was done under the supervision first of R. F. Murphy, Chief Geologist, and later of E. B. Gillanders, Eldorado Mine Manager and Manager of Eldorado Exploration Division. W. F. James and B. S. W. Buffam are consulting geologists. Since 1946, S. N. Kesten has supervised geological work for the Company in the Goldfields area. Where maps of Eldorado properties have been included in this paper, the name of the geologist who examined the property is acknowledged on the map. Outline of General Geology The geology of the area is described in the Goldfields and Martin Lake preliminary maps of the Geological Survey and accompanying Paper 49-17. In brief, the Tazin series of Precambrian age, consisting mainly of sediments with minor interbedded volcanics and basic intrusives, is intruded and replaced by granite, now generally gneissic. The late-Precambrian Athabaska series of conglomerate and arkose, with interbedded basalt and andesite flows, rests unconformably on the older rocks. All these rocks are cut by small diabase dykes. The geological terms used in this paper and in the accompanying figures are standard with the exception of the term 'mafic rocks'. These include all the basic or dark coloured rocks of the Tazin group, such as amphibolites, biotite schists, and chlorite-epidote rocks (greenstones), whether they be of extrusive, intrusive, or sedimentary origin.

Jan 1, 1949

By M. S. Greenfield, E. Cocchiarella, S. Chubbs

"At Dofasco sNo.4furnace a variation of the basic oxygen steelmaking process, Klockner Oxygen Bottom Maxhutte (K-OBM), is used to produce steel. Large amounts of hot gases and particulate are evolved during the oxygen blowing phase. A quencher and a venturi scrubber are used to collect over 99.5% of the particulate. In 1990, the authors investigated the effect of foamy slag on the particulate emissions from the furnace. The amount of lime added early in the oxygen blowing cycle was reduced, making the slag more viscous and foamy for a six minute period. Instantaneous particulate emissions were monitored throughout the blow by analyzing quencher and venturi scrubber water samples. Particulate emissions were reduced up to 59% during the foamy slag period.IntroductionThe reduction of the amount of waste generated or control of emissions at source is at the top of the ""3R"" hierarchy of waste management (Reduce, Reuse, Recycle). Process and operating practice changes are often the most economical ways to control emissions. At Dofasco, they investigated the effect of operating practice changes, specifically the formation of a foamy slag, on particulate emissions from steelmaking furnaces. They wanted to determine if a foamy slag changed the quantity and nature of the fume evolved from the K-OBM furnace over the oxygen blowing phase.The Basic Oxygen Steelmaking ProcessesThe basic oxygen steelmaking process (BOP) generates large quantities of very fine metal oxide fume during the production of steel. In this process, scrap steel and molten iron (hot metal) from blast furnaces are charged into a steelmaking furnace. Then pure oxygen is injected and a lime flux added . The oxygen reacts with carbon dissolved in the molten iron to form carbon monoxide. Oxygen lances can have secondary nozzles which introduce oxygen above the bath. This secondary oxygen, known as post-combustion, bums some of the carbon monoxide radiating the heat back to the bath. Particulate and gases rich in carbon monoxide are ejected from the furnace during the oxygen blowing phase and are collected by a gas cleaning system. Typically, more than 99.5010 of the particulate is scrubbed from the gases by high energy venturi scrubbers or electrostatic precipitators. The oxide sludge or dust collected may have elevated zinc and lead which is unsuitable for recycle to blast furnaces. Due to the presence of these undesirable elements, treatment and disposal of steelmaking oxide dust is difficult and costly."

Jan 1, 1993

By Ibrahim Ocak

The prediction of machine utilization time and determining machine performance plays an important role in scheduling and planning tunnel excavation and data base created serve a major role in further applications. In this study, the construction methods of two twin tunnels situated between Basak Konutlari station and Istoc station are summarized. Geology in the study area is composed of fill and weak rock, respectively starting from the surface. The tunnels of 5.6 km in length were excavated with two different earth pressure balance machines (EPBM). Excavation diameters of the EPBMs were 6.564 m. The performance of the machines are analyzed and compared in order to accumulate data for further applications in similar ground conditions in Istanbul. The distance between two twin tunnels is 14 m from center to center and the EPBM in the one tube was almost about 100 m behind the other tube. Segmental lining with 1.4 m of length and 30 centimeters of thickness were used as final support. The overall performances of the two Lovat TBMs are found to be respectively as; the best daily advance rates 30.8 m/day and 30.8 m/day, the best weakly advance rates 115.0 m/day and 153.9 m/day, the best monthly advance rates 388.7 m/day and 400.5 m/day. Total waiting and maintenance times were 25.2 and 16.7 %, respectively.

Aug 1, 2013

By Michael Chender

Emerging Equity Sources ? Larger IPOs ? China Inc. ? Other sovereign wealth funds ? New funds and higher allocations ? Private equity

May 1, 2010

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By Xuanxue Mo, Kaihui Yang, Steven D. Scott

Abstract -The Changning-Menglian metallogenic belt in western Yunnan, China, is characterized by the occurrences of both Pb-Zn-Cu and Cu massive sulfides in Permo-Carboniferous mafic volcanic sequences. These deposits were formed in a back-arc basin at a rifted continental margin in the Paleozoic Tethys Ocean. Pb-Zn-Cu deposits are associated with alkalic basalt, andesite, and lesser felsic volcanic rocks intercalated with limestone, which probably formed along an immature rifting segment on a continental basement. These volcanic rocks are enriched in K, Ti, LREE, and other incompatible elements, and have the attributes of alkalic within-plate basalt. An extensive unit of sulfide- carbonate-silica shale in proximity to massive sulfides contains high values of Mn, As, Mo, W, Sn, Sb, and Hg, and has REE patterns that are similar to the volcanic rocks. This, together with the graded bedding in the footwall volcanic rocks, suggests that the sulfides precipitated in a shallow, unstable, and carbonate-saturated volcanic basin. A stringer zone is traced downward for 500 m below the massive sulfide orebodies. It is characterized by an upper sericite-quartz zone and an extensive lower skarn alteration with enhanced W, Sn, and Bi. Lead isotope data show both continental basement and magmatic sources may have supplied the ore metals. Cu deposit and occurrences are hosted by tholeiitic units that represent the mature spreading segments in the back-arc basin. The tholeiitic lavas have LREE-depleted or flat REE patterns similar to MORB or back-arc mafic lavas. The cupriferous massive sulfides are overlain by an extensive unit of chlorite-magnetite or ochre, suggesting a relatively oxygenated oceanic basin. Ni and less Co mineralization is found in dolomite veins of the stringer zone. Enhanced concentrations of Ni, Co, Au, and As are found in the massive sulfides and in sulfide-rich tuffites. The geological setting and mineralization of the Changning-Menglian belt has similarities with modern back-arc basins such as the Manus Basin in the western Pacific.

Jan 1, 1999

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the RISKGATE body of knowledge captured specifically for the management of unwanted events that stem from the handling and use of explosives (drill and blast) within surface coal mining operations. The knowledge presented is divided into a series of initiating events (listed below) within which there are further degrees of classification based on design, operation, and management concerns. Initiating events: ? Loss of control of explosives and associated chemicals in storage on site ? Loss of control of explosives and associated chemicals during transport ? Loss of control of explosives and associated chemicals during manufacture ? Loss of control of explosives and associated chemicals during handling and blast operations ? Loss of control of explosives and associated chemicals during disposal The system guides the user in generating substantive and leading-edge controls to assist in the design, management and reporting of drill and blast operations to meet stringent internal and external requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013

By Andrew Bamber

The mining and beneficiation of minerals is the second largest end-use of electrical power on the planet, and comminution is by far the largest single contributor to this. Several jurisdictions, including British Columbia, have, in response to concerns about greenhouse gas emissions and climate change, adopted energy conservation legislation, including carbon taxes, carbon trading and conservation incentive schemes. Key to achieving conservation objectives is firstly an understanding of usage metrics across the various unit operations in the sector, and secondly an understanding of the conservation potential represented by available technologies and approaches in reducing end-use. This paper presents the results of a recent utility-funded study on energy use metrics and conservation potential at large open pit mines which are typical of the sector in BC.

Aug 1, 2013

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By N. Ahern, M. Barbanell

Mercury is often present in gold ores and can be released during processing. In view of health and environmental concerns related to mercury, the mining industry takes leadership in the responsible management of mercury. This paper reviews various aspects of mercury management, including an overview of mercury deportment in typical gold processing flowsheets; trends in mercury legislation impacting the international flow and management of mercury in the gold mining industry; and treatment, storage and disposal options for mercury and mercury containing materials.

Jan 1, 2014

By T. J. Bruce, G. E. Agar, R. Stratton-Crawley

"A technique by which the design of a flotation circuit may be optimized is described and examples of the application of this methodology are given.Three interrelated criteria are defined and the application of these criteria to the selection of the optimum residence time for each stage of a flotation circuit is demonstrated. The criteria are:(1) Add no material to the concentrate that is lower in grade than the feed to that separation stage.(2) Maximize the difference in recovery between the desired mineral and the gangue.(3) Maximize the separation efficiency.Three independent systems were examined experimentally and it was shown that application of any of the criteria yielded similar results.It was demonstrated how the application of rate measurements (Criterion #2) could lead to the selection of a set of optimized times for several stages in a flotation circuit and that these could in turn be used to simulate the results of a locked cycle test. The predictions were checked against the experimental results from a locked cycle test and there was substantial agreement between the predicted and observed results."

Jan 1, 1980

By Rocky (Yaokun) Wu

Rock burst is one of the biggest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost effective yielding rock bolt. This paper introduces a new yielding rock support - Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150 ~ 250 mm of deflection at 8 ~ 10 metric tons (Mt) loads for every 16.4kJ energy input. Its performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described, the dynamic testing results are discussed; and the features and application of the bolt are presented.

Oct 1, 2010