Search Documents

By T. Gerritsen, T. Plikas, K. Ochoa, M. Loveless, R. MacRosty, J. Reichart, R. Pula

Sidewall accretion in a smelting furnace plays an important role in furnace integrity as it provides protection to the sidewall cooling elements and thereby extends the furnace campaign life. The extreme thermal and mechanical stresses in the furnace and changes in the slag chemistry can cause the sidewall accretion to melt or break away decreasing the lining protecting the cooling elements. Thin accretion is highly undesirable as it increases the risk of exposing the cooling elements to the molten bath and in the worst case may lead to a failure. Therefore, monitoring the sidewall accretion on an operating furnace is extremely important to manage furnace integrity and to support safe furnace operation. Operators often generate estimates for sidewall accretion and refractory thickness using either copper cooler temperatures or heat load into the cooling water circuits. Multivariate statistical models, on the other hand, have the capability to consider all the process measurements simultaneously to provide a more reliable estimate. This paper describes the application of multivariate statistical models for sidewall integrity monitoring on a Flash Converting Furnace (FCF) and also discusses the online implementation of these models as the Sidewall Accretion Monitoring System. INTRODUCTION Rio Tinto’s Kennecott Utah Copper (KUC) smelter located near Salt Lake city, Utah operates a Flash Smelting Furnace (FSF) and a Flash Converting Furnace (FCF) to produce high-grade matte and blister copper respectively. Since the commissioning of smelter in 1995, several improvements were made to these furnaces to increase their efficiency and operational safety. At present, Kennecott smelter is known to be among the lowest-emission and highest energy recovery copper smelters in the world. Since the smelter start-up, Kennecott has invested in several advanced furnace monitoring practices to evaluate the integrity of the furnaces and improve their campaign life. An example is their temperature monitoring system installed for the smelting and converting furnaces, which continuously monitors the furnace sidewall temperatures and notifies the operators during temperature excursions. During an investigation on the converting furnace, it was revealed that there were frequent temperature excursions in the settler sidewall area towards the reaction shaft end of the furnace that caused significant furnace downtime. The reason for the sidewall temperature excursions was not clearly known.

Jan 1, 2019

By Gonzalo Bernstein, David G. Meadows, German Naranjo, Edgardo Tapia

"During the last decade Antofagasta Minerals’ Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.INTRODUCTIONMinera Los Pelambres is a world class copper-molybdenum operation located in the Salamanca area in Chile, in region four, approximately 500 km north east of Santiago, the capital of Chile. In the late 1990s Antofagasta Minerals developed the Minera Los Pelambres project in Chile at an investment cost of approximately $1.3 billion USDs. The project construction was successfully led and completed by Bechtel Corporation in 1999 and within a matter of months the plant was already exceeding the nameplate capacity of 85,000 mtpd. In 2001 a pebble crushing circuit was added to raise the capacity to 114,000 mtpd. In the early part of 2003-2004, it was recognized that the hardness profile was changing with depth and that in order to maintain the plant capacity additional power would be needed in the SAG mills together with upgrading of the primary crusher. In conjunction with these changes a fifth ball mill and a second primary crusher station would also need to be installed. A further detailed engineering study and evaluation was initiated by Minera Los Pelambres. This was lead by Bechtel Corporation with major design contributions from FLSmidth and Siemens in order to establish the re-powering requirements for the SAG mills. These re-powering changes together with the inclusion of a pebble crushing circuit took the plant to up to 125,000 mtpd even with harder more competent ores. Finally in the last two years an additional grinding line has been added to take the capacity to consistently over 175,000 mtpd. The third line was installed in a record time of 256 days. A schematic of the current comminution circuit, discussed in this paper, is shown in Figure 2."

Jan 1, 2012

By David Eichenberg

A154S A154N After 3 Years of Mining ?Current mining Level A154S 280RL ?110 Vertical metres of A154S ?Current mining Level A154N 300RL ?100 Vertical metres of A154N ?Variations in Kimberlite Volume ?Ore Types and Plant Production

May 1, 2006

By Gerald S. Cole

It used to be that a science/engineering presentation on "light weight" at a metallurgy conference, would relate to the materials science, processing, component fabrication and applications of aluminum, magnesium and titanium. Within the automotive industry, light weight now includes how to "lighten up", how to lightweight, or how to mass reduce vehicle components and systems. Increasingly stringent global emissions-reduction requirements require increasing vehicle fuel efficiency; mass reduction is an enabler to achieve this. While light metals certainly are the basis, a host of other materials can be used to optimize mass reduction while meeting vehicle performance, safety and cost requirements. New grades of ultrahigh strength steels and even nanosteels can be thinned down and save over 1/3 the mass vs conventional mild steels. A compacted graphite cast iron engine can be made lighter than an aluminum one. Aluminum components in vehicles were only castings; now aluminum stampings, forgings and extrusions are becoming more visible components of mass reduction. Lower mass high temperature polymers, and carbon fiber polymer composites now replace aluminum and steel. These materials often require specialized processing and manufacturing techniques to produce a component, including superplastically formed twin roll cast sheet aluminum and magnesium, and hot stamped/in-mold quenched steels. The assembly of hybrid structures requires unique joining/bonding, and corrosion-inhibiting techniques that might include sophisticated structural adhesives. This thinking "light" presentation, will conclude with a discussion of U.S. and Canadian government engineering and research support for mass reduction, including the proposed $148 M American Lightweight Materials Manufacturing Innovation Institute.

Jan 1, 2014

One Data Set for the Lifecycle Complete data captured at the logging stage benefits the entire life cycle Exploration Technical Studies Production and Milling Visible Light Spectrum Hyperspectral, put simply, is the interaction of light with matter based on the nature and chemical structure of the specimen. SpectrumWe develop the library to match the liberation size fraction Analyses every 1mm2 1 meter of NQ core = 35 000 analysis data Crystal size detection : 0.1 micron

May 1, 2013

By C. Mills, A. O. Burt

"The paper examines the role of gravity concentration in both an historical context and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of more mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration with other forms of processing.IntroductionIt is an unfortunate, albeit popular, misconception among otherwise enlightened engineers in the mineral processing industry that gravity concentration was a process developed in the dark ages, perfected in the middle ages, and abandoned in the modern ages.Gravity concentration was developed in the dark ages - long indeed before that. Agricolau: cited examples of gravity concentration, crude examples admittedly, being practiced over 3000 years ago. However, gravity concentration is not dead. Far from it. As recently as 1978 it was reported that the total mineral tonnage treated by this process in the United States was greater than that processed by flotation. Coal represents the bulk of the or e treated by gravity separation in the U.S.A., with iron ore representing a major portion of the balance."

Jan 1, 1985

By M. Fiset, D. Belley

"To better understand the wear process of various materials that may be used as blades on snow removal equipment, the first step is to evaluate the influence of the load applied and the moving speed on road wear rates of one type of steel and three types of polymers. While the behavior of steel conforms to Archard's law, wear rates of polymers increase to a power of ex of the load applied according to a model implying that the wear of these materials is due to fatigue. The wear rate of some of the polymers varies considerably in terms of speed, unlike the steel. The wear resistance of some of these polymers outclasses the steel tested as long as the speed is not too great. They, therefore, present interesting alternatives for snow removal on more fragile surfaces such as sidewalks and zone made of inter-block slabs.IntroductionSince the dawn of the Industrial Revolution, the massive use of machines has brought with it a number of different problems regarding wear. Snowplowing roads, parking lots and sidewalks is an activity that generates enormous expense in a country such as Canada. To better understand these wear processes and in the hope of stimulating new approaches designed to reduce the costs related to this sector of activity, this paper presents the behaviour of several materials (steel, polymer and rubber) as they wear on an asphalt-fines matrix surface lubricated with water. Also discussed is the effect of various parameters such as the load applied and speed."

Jan 1, 1990

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By J. E. Nesset, E. R. Bobicki, K. L. Bilaniuk

The introduction of froth flotation technology in Canada, and in particular, in British Columbia, began not long after it was successfully applied in the Broken Hill mining area of Australia which began around 1905. It proved to be a revolutionary and transformative technology that resulted in marginal operations in copper, lead and zinc becoming profitable in spectacular fashion. The paper presents the technology of both oil flotation and froth flotation in the context of the challenges of the time and its early application in British Columbia at the Le Roi No.2 mine (1903), the Britannia Copper mine (1912), and at the Allenby concentrator of the Copper Mountain mine (1918-19). New-found archival documents indicate the Britannia application to be the first production application of froth flotation for copper ore outside Australia, a claim that is currently made by the Braden mine (now El Teniente) in Chile. Flotation was initially an add-on process following gravity methods but was rapidly shown to be far superior method for the bulk and selective recovery of metal sulphides. Flotation proved particularly successful for the recovery of zinc sulphide (the so-called ‘zinc problem’) which was considered a contaminant at the time. The ‘copper problem’ related to the poor recovery of fine copper sulphide particles that were not amenable to gravity methods. The success of flotation led to changes in both the scale and methods of mining, concentration and smelting in a manner that allowed integrated mining companies to flourish. Many are still with us today. INTRODUCTION The advent of froth flotation in the early 20th century was truly a revolutionary technological development, not only for the mining and metallurgical industries, but arguably more so for business and society overall. The Canadian technology historian Jeremy Mouat stated (1996) “The development of flotation was the greatest single metallurgical improvement of the modern era...it is not overstating the case to claim that flotation was of central importance to the smooth functioning of the global economy”. It should, therefore, be a story of interest to us all. The aim of this paper is not to retell the full story, that has been well covered by others (Hoover, 1912; Rickard, 1916a; Hines & Vincent, 1961; Lynch et al., 2010) but rather to add some Canadian perspective and the key role played by companies and individuals in those early days, focusing on events in British Columbia’s copper industry. EARLY DEVELOPMENTS During the later half of the 19th century, a number of flotation-related patents were issued. These include the 1860 patent (Britain) granted to William Haynes for a process to separate sulphides from ground ore by mixing it with oil (1-10% wt) followed by a separation process in a water-filled vessel; the 1877 patent granted to Georg and Adolph Bessel (Germany) for a process involving the mixing of oil and graphite ore followed by boiling in water to produce a high grade graphite froth (>90% carbon); and the 1885 patent granted to Rebecca ‘Carrie’ Everson for the separation of sulphides by mixing sulphide ore with small quantities of oil, and adding water followed by sulphuric acid. These processes are more properly referred to as bulk oil flotation due to the relatively large quantity of hydrocarbon used.

Jan 1, 2019

By G. Robert Guillet

"Ontario enjoys the advantage of its proximity to the large industrial market of northeastern North America. Together with Quebec and fifteen nearby U.S. states, an industrial base of more than half the total for both countries is provided by a population of 100 million.Mineral fillers such as barite, calcium carbonate, kaolin, mica, silica and talc are of major importance in the manufacture of paper, paint, plastics, rubber, vinyl tile, carpet backing, putty, caulks, sealants and adhesives. Ontario has all of these minerals, but domestic production falls short of demand in some cases, and mica and kaolin are not produced at all.This paper reviews the market and outlines the distribution of the major filler-consuming plants of northeastern North America. It also identifies the principal producers of filler minerals in the United States and Canada.IntroductionOf all the uses for industrial minerals, mineral fillers are probably the least understood. Originally used primarily to add low-cost bulk to a variety of commodities without seriously affecting their properties, filler minerals have become essential components that enhance and extend the properties of their hosts. Hence the term ""extender"" which, for all practical purposes, is synonymous with ""filler"". Today, fillers and extenders are not solely low-cost additives, but ingredients that provide essential characteristics to the products they fill.The major markets for mineral fillers are paint, paper, plastics, rubber, adhesives and floor coverings. But there are many others: putty, pesticides, wire and cable coatings, caulking and asphaltic compounds, oilcloth, wall-paper, joint cements, inks, sealants and many others. Barite, calcium carbonate, kaolin, mica, silica and talc are among the more important filler minerals discussed in this paper, but there are at least a dozen others. And the increasing practice of coating the mineral surfaces with certain coupling agents or metal stearates is constantly expanding the range of characteristics and hence the marketing opportunities.Whiteness, particle shape, fineness of grind and cost are the principal considerations in selecting a filler, but other characteristics such as weight, opacity, hardness and chemical inertness may be dominant considerations in specific applications."

Jan 1, 1987

By Jacque Turgeon, Gontran Foy

"The Mineral Research Centre of the Quebec Department of Energy and Resources has worked extensively on the development of a dry process to extract pure mica flakes from a phlogopite ore. The liberation of mica from the gangue is effected basically by impact crushing, and the ground ore is screened into several fractions, each having a fairly narrow range of grain size. Each sized fraction is then fed to an air separator where heavy grains are separated from light flaky grains. Heavy fractions are returned to hammer mills where gangue minerals are ground finer and blocky mica particles are exfoliated. A second stage of screening is performed and each fraction is sent to an air separator. This sequence is repeated until mica products are virtually free of gangue. These different fractions are then treated in a cage mill in which mica flakes undergo a more orderly exfoliation along cleavage planes. The ground mica is again submitted to a final screening stage, after which each fraction constitutes a final commercial product.This process permits the recovery of about 70% of the mica contained in the ore. The over-all process will be described along with technical details of each unit operation. Recent work on a wet grinding method to produce very fine mica will also be discussed.IntroductionRecords of production of mica in Quebec date back to 1886. Production has been more or less continuous since that time, with peak activity during the war years. Production was interrupted in 1966, but started again in 1972 when Marietta Resources and Laviolette Mining and Metallurgical Corporation started their joint operation in Canton Suzor, northwestern Quebec. Mica deposits of more or less importance exist in different parts of Quebec, of which three have attracted attention in recent years: the Canton Suzor deposit, the Canton Lamy deposit and the Canton Chasseur deposit. The Suzor orebody was first identified by Carl Faesler in 1936, who described the rock as ""brown biotite in flakes half an inch in diameter, with interstitial augite, apatite and feldspar""."

Jan 1, 1982

By T. Ouellet, F. Chiesa, J. Carignan, D. Levasseur

Common practice for the preparation of permanent mold for aluminum casting is to coat the mold with a ceramic suspension to obtain a chemically stable interface with the aluminum melt. This practice serves two purposes: first, it helps the thermal regulation of the mold and second, it prolongs its life. The possibility of increasing the coating durability by applying it by thermal spray is appealing. Plasma spray of zirconium oxide based coatings was performed on H13 tool steel to study the coating’s thermal fatigue resistance. A unique dip test setup was used to characterize the thermal fatigue resistance of the coatings and of bare H13 steel. Observations of the failure mechanism bring an insight on the requirements of the coating to maximize its durability.

Jan 1, 2014

By Sarah R. Hindle

Carbon capture and storage has jumped to the forefront of climate change mitigation efforts for its capacity to sequester large amounts of carbon. Mineral carbonation is one prominent option, mimicking and accelerating the natural weathering process of certain silicate minerals. This has the ability to produce stable carbonate minerals that can store carbon on geologic time scales with little to no risk of leakage. Commercialization of this process is ideally suited for integration into the proposed mining operations at the Turnagain Nickel site in Northern BC. This is due to the abundant supply of suitable ultramafic feedstock material, as well as the economic benefit of sharing costs while reducing net emissions and bringing value to otherwise valueless and costly waste rock. While studies have shown this process to be technologically viable on a laboratory scale, assessing the economic and financial viability of such a process on an industrial scale is necessary. An evaluation of the financial feasibility of integrating mineral carbonation into the mining cycle at Turnagain under a proposed cap-and-trade system is presented.

May 1, 2010

By Robert Cameron, Colin Ashton, John MacNeil, Leo Piciacchia

"The in pit dam construction and utilities relocation, known as the East Mine Corridor Relocation (EMCR) project, was developed to extend the life of the east side of the Base Mine pit by two veal's. This will result in the recovery of an additional 80 million barrels of oil and delay expenditures associated with the opening of the North Mine by two years. To accomplish this, a large in pit earth structure was required to provide a new embankment foundation for relocating a public highway, four powerlines, a natural gas back-up pipeline, a substation, and a conveyor train. This structure would also he required as a temporary dam 10 contain mature fine tails on the west side until mining is completed in the east mine corridor area, that will then be filled with fluid.The in pit dam, known as The Highway Berm, is 2.5 km long, 63 m high and has 42 million m3 of engineered soil added to the already existing end-dumped soil volumes. To complete the design and construction of a structure of this magnitude, in the very short time frame of two-and-a-half years, presented many new challenges. The main challenges faced were: designing while construction was ongoing; designing without the use of clay cores or sand filters; using relatively non-select overburden material; proper dewatering and base preparation; changing from construction of 50 m high spoil piles to a high specification construction operation; compacting lifts with heavy haulers; constructing during the winter; and monitoring movement of the structure with satellites."

Jan 1, 1995

By Les F. Sawatsky

Surface drainage, particularly mine closure drainage, must be properly considered during all stages of mine planning because it presents constraints that are critical to economic mine operation, minimizing environmental impacts and ensuring compliance with government regulations. Deficient mine site drainage increases costs of operation, causes unnecessary environmental impacts and may result in regulatory violations. The scope of this paper includes stream diversions around mine areas, drainage systems within the mine disturbed footprint, and closure drainage works to control surface water, ground water, erosion, sedimentation, and seepage discharges following mine operations. Developing selfsustaining drainage facilities upon mine closure, requires a mine plan that develops appropriate topography and constructed drainage courses that replace the function of pre-disturbance drainage systems without aggravated erosion and deterioration. Drainage criteria, particularly closure drainage criteria, represent important constraints on mine planning and are best considered by integrating drainage features into the mine plan well in advance of mining activities. Integrated mine planning by a multi-disciplinary team is recommended to achieve closure objectives at minimum cost and maximum effectiveness The geomorphic approach to channel design is an effective means of providing a drainage system that has the appearance, function and longevity of natural systems. By incorporating this technique into closure drainage planning, mine operators can construct sustainable (walk-away) drainage systems that require little or no maintenance in the long-term. This paper presents a process by which drainage criteria and associated mine plan constraints can be integrated into the mine planning process. This paper outlines the process for detailed design of drainage facilities, particularly closure drainage systems that are designed by the geomorphic approach.

May 1, 2009

By David Penswick

Despite anecdotal evidence to the contrary, the mining industry is not in decline. Rather, the world?s largest mining companies are among the most consistently profitable companies in any industry. In many cases, profitable mining companies have been built around a few large scale, long life mines. These criteria for success ? size and long life ? have led to the current preference for deposits that can be exploited using open pit methods. However, developments in the science of block caving have resulted in this mining method achieving costs and productivities that are competitive with the largest open pits, while achieving widespread applicability. One implication of the low costs and widespread applicability of block caving is that some current open pits are possibly too deep.

May 1, 2003

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

An Attractive Investment ?Near term low cost and secure PGM producer ?restricted supply legislated demand ?strong pipeline of resource development ?Building Canada?s largest undeveloped PGM-Cu resource ?All work (resource, reserves, DFS, EA) is NI43-101 compliant ?Strong balance sheet: over $8 m in cash with no debt

May 1, 2010

By W. K. Chan, R. Lahaie

"The Suncor Oil Sands Mine located north of Fort McMurray, Alberta, produces about 80000 m' per day of tailings waste which must be disposed of economically in an environmentally acceptable manner. To date, this has been accomplished by impounding the high water content tailings wastes behind large dykes, many of which approach 100 m in height .The dykes are constructed using suitable overburden material stripped prior to the mining of the oil sands feed and/ or the coarse sandy fraction of the tailings waste itself. Although the above is common practice at many mining operations, the large volumes handled and the resultant costs require designs to be meticulously fine-tuned toward the optimum. As a result, considerable effort is expended on planning, designing and construction, and performance monitoring. The lack of precedent experience (Suncor pioneered oil sands mining), coupled with the realities of long, harsh winters and a variety of troublesome site conditions and construction materials, has led to some very unique dyke construction.This paper overviews current tailings disposal plans as welt as some of the key issues related to the design, construction and performance of these large dykes."

Jan 1, 1988

By A. B. Parsons, P. G. Howes

"This article discusses how recent changes in the federal and Quebec .income tax laws have contributed to an improved investment climate for mineral exploration in the Province of Quebec. Individual investors who are resident in Quebec and who are in the highest tax bracket (1984-60.4% marginal rate) may obtain tax benefits that result in only nine cents of each invested dollar being at risk.IntroductionIn a recent submission by the Mining Association of Canada to the Royal Commission on the Economic Union, it was stated that the mining industry ""is no longer discovering and opening new mines at rates sufficient to offset the depletion of existing orebodies and to maintain pre sent output"". With world metal prices still in a depressed state following the prolonged 1981-82 recession, moreover, the continuing success of Canadian mining in world markets will depend on this country's ability to compete in a new environment characterized by subsidized Third World production . For the most part, this new competitive environment will encourage the development of cost-efficient mines that are better equipped to withstand the troughs and valleys of international metals prices."

Jan 1, 1984