Search Documents

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a continuous-recording methanometer utilizing a catalytic combustion detector. The methanometer, which is presently operating at 22 exhaust fans at 14 mines in the Eastern coalfields, is reliable and simple to install, operate, and maintain. The instrument and the details of its installation and calibration are described. Analytical data obtained by infrared spectrophotometer and gas chromatograph are presented to substantiate its re liability.

Jan 1, 1974

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Wilbert J. Huff

The organization of the Explosives Division has been outlined in two preceding publications., The activities of the various units for the fiscal year 1939 are described hereafter: I. INFLAMMABILITY OF GASES AND VAPORS DETERMINATION OF EXPLOSION HAZARDS OF COMBUSTIBLE GASES AND VAPORS IN MINES AND INDUSTRIES (a) Determination of Limits of Inflammability of Gases and Vapors The following hitherto unpublished limits of inflammability were determined during the past fiscal year.

Jan 1, 1939

By T. E. Gray

This report describes the preparation characteristics of the signifi¬cant coalbeds in Preston County, W. Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 2 million tons of coal was produced in Preston County, W. Va. in 190, none of which was cleaned mechanically. Estimates as of January 1, 1959, indicate that more than 3 billion tons of coal remained in the county in beds 12 inches or more thick. The Bakerstown, Mahoning, Upper Freeport, and Upper Kittanning beds were selected by the Bureau of Mines for study based on current production and estimated minable reserves. Sample locations were selected after study of the literature, conferences with mining engineers and mining company offi¬cials in the field, and examination of available sites. Four samples were collected from the Bakerstown and Upper Freeport beds and one each from the Mahoning and Upper Kittanning beds.

Jan 1, 1961

By Wilbert J. Huff

The organization of the Explosives Division has been outlined in two preceding publications.3/ The activities of the various units for the fiscal year 1939 are described hereafter: I. INFLAMMABILITY OF GASES AND VAPORS DETERMINATION OF EXPLOSION HAZARDS OF COMBUSTIBLE GASES AND VAPORS IN MINES AND INDUSTRIES (a) Determination of Limits of Inflammability of Gases and Vapors The following hitherto unpublished limits of inflammability were determined during the past fiscal year.

Jan 1, 1939

By J. W. Howland

A demonstration of dozer blades, designed for recontouring area-mined spoil and shown effective at Kansas and East Texas surface mine sites, was conducted at a Northeast Arizona surface coal mine to determine their effectiveness in different climate and soil conditions. The specialized tools were: 48-ft angle blade (on side-by-side tractor), 24-ft grading bar, modified 24-ft "U" blade (on side-by-side tractor), and a 13-ft deep "U" blade. Interest in the increased dirt-handling capacity of a previously built 22-ft blade, resulted in the design of a new Centerflow Blade of good versatility, able to maintain increased flow in otherwise difficult-to-move spoil. The demonstration involved 263 acres and showed a reduction of 50% in reclamation costs and 20% in fuel requirements for this mine site over conventional equipment. This savings resulted from improved technology, trained operators, and rigorous application of supervisory and monitoring techniques. Procedures and results of the demonstration are presented and analyzed here, along with guidelines for application of findings.

Jan 1, 1982

By J. Cooperman

THE INVESTIGATION was carried out in three stages, depending on the objectives of the work and the kind of equipment used. The first stage involved testing of 11 representative Alabama coals, the source of which is given in table 1. The objective was to find whether these coals could be gasified raw by the Lurgi method, and the equipment used was a 4-inch batch generator (to be described later). This generator proved too small and difficult to control to provide adequate amounts of products under continuous operating conditions for testing. For the second stage, a 6-inch batch generator was used, which was provided with facilities for superheating the steam-oxygen mixture and for synthesizing additional methane from the residual carbon monoxide and hydrogen in the primary Lurgi gas. Selected Alabama coals, Pittsburgh-bed coal from West Virginia, "Disco," and anthracite were used. For the third stage of the work, a continuous generator of 1 square foot grate area, following closely the design of the industrial generators operated in Germany, was provided. This generator was designed by 0. Hubmann, engineer for the Lurgi company, and was expected to give results closely simulating industrial-scale apparatus. The purpose of this equipment was to test prepared materials shown to operate smoothly in the 6-inch generator under conditions approximating as nearly as possible those prevailing in industrial practice. Work of the first stage showed that Alabama coals could not be used in the Lurgi process without first destroying the coking power.

Jan 1, 1951

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By L. B. Berger

From time to time the Bureau of Mines receives requests for information and advice regarding the safety of using internal-combustion engines operated on butane fuel as prime movers for haulage and other purposes in mining and tunneling. The purpose of this, circular is to discuss the properties of butane and to present data in regard to the possible use of this fuel in underground operations. Published information on the use of commercial butane as a fuel for internal-combustion engines indicates that, insofar as performance is concerned, butane may be utilized satisfactorily and efficiently for this purpose. However, the introduction of a volatile, inflammable material such as butane into confined spares such as mines or tunnels would create potential fire and explosion hazards that should be given due consideration by those concerned with the promotion of safe practices.

Jan 1, 1944

By Russel R. Bohn

The objectives of this study were to: (a) determine the state of the art for the control effectiveness of various chemical dust suppressants, (b) field test the effectiveness of the dust suppressants, and (c) develop technical guidelines for selecting and implementing cost effective tailings pond dust control programs. Chemical stabilizers evaluated under field conditions were: Coherax, Calcium Lignosulfonate, Nalco 656, 655, and Magnesium Chloride. Testing in the field utilized a portable field in-situ wind tunnel. The wind tunnel was placed on the tailings surface and simulated wind speeds of up to 80 mph were used to determine wind erosion threshold velocities. Emission rate testing was performed with the wind tunnel through the use of a real-time cascade impactor. A control cost effectiveness evaluation was performed to determine how efficient the chemical stabilizers were on a dollars expended per acre basis.

Jan 1, 1983

By John P. Wagner

The details of a three-phase study (total time period of 12 months) entitled ?Fire Alert Systems for Metal and Non-Metal Mines,? are presented. Phase 1 consists of a state of the art survey on fire detection devices and gas sensing techniques. Phases 2 and 3 include laboratory screening and systems concepts testing on various detectors classified as products of combustion, optical view-field and contact (or thermal) types under incipient and flaming combustion conditions. Recommendations for a mine fire detection system to protect shaft, sealed off or mined out (from spontaneous combustion of sulfide containing ores and cellulosic materials), and fuel storage areas are also included. me principal problem area noted during Phase 1 study is the high expected occurrence of false alarming of products of combustion detectors (POC") subjected to normal mining operations---diesel vehicles and equipment and shot firing or blasting operations. Simultaneous gas sensing of either the ratio of CO/NOx or CO2/NOx with detection of one or more fire signatures (smoke, radiant energy, or heat sensing) is the recommended approach to discriminate against these operations.

Jan 1, 1975

By M. M. Ayoub

With a return to coal as a major energy source for many companies, more emphasis is being placed on recovery of coal from areas that were formally considered uneconomical to mine. Increasing emphasis is being placed on production from low coal (seam height 48 inches or less) as high coal seams are depleated. Mining in restrictive spaces requires unusual work postures that can turn easy jobs into demanding ones. The objectives of this research were: (1) to evaluate the job demands associated with low coal mining, (2) to survey the anthropometry, strength, and aerobic capacity of low coal miners to determine if they differ from the U. S. population, and (3) to recommend, on the basis of available information, optimal job and work station design for low coal mining. This research effort was supported by the U. S. Bureau of Mines. The male and female anthropometry with the exception of weight and circumferential dimension, was quite similar to the comparison population. Back strength for male and female miners was significantly lower than the industrial worker population. This can be one of the contributing factors of low back problems in mining. Shoveling, timbering, and helpers tasks were physiologically demanding activities. However, due to the frequent stoppage of work, adequate rest was usually available. If work stoppage is corrected, then better work/rest schedules are essential.

Jan 1, 1981

By Walter D. Holland

This is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended for training those, usually the safety officers, who perform surveys for inhalation contaminants in above ground work areas. The handbook entitled ?Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual for the course and as a prime reference when performing the actual surveys or interpreting the sampling results. There are six experiments for the students to perform during the course to familiarize them with the sampling devices routinely used during the surveys.

Jan 1, 2011

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

By Thomas W. Camm

In this U.S. Bureau of Mines report, mine and mill cost models are presented to make quick estimates of the cost to develop mineral deposits in the desert region of the Southwest United States. Regression analysis was used to generate capital and operating cost equations for each model in the form Y = AXB, where Y is the cost estimated and X is the assumed daily capacity in short tons. A and B are constants determined by the regression analysis. Each is broken down into 11 subcategories to facilitate escalation of costs for inflation and to increase their versatility in economic evaluation work. This report contains 2 open pit models, 6 underground mine models, 11 mill models, and cost equations for access roads, powerlines, and tailings ponds. In addition, adjustment factors for variation in haulage distances are provided for open pit models and variation in mining depths for underground models.

Jan 1, 1991

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By Virgil A. Marple

The objective of this contract was to conduct characterization, evaluation and/or calibration studies of instrumentation used for measuring the quantity of respirable dust in mining atmospheres. Initially, this work involved the upgrading and detailed evaluation of the aerosol test chamber and the development of impactors with respirable classification characteristics. These were used as standards in the chamber for measuring the quantity of respirable dust based on either the ACGIH or BMRC respirable dust criteria. A program was then conducted to calibrate several photometers. In addition, the mass sensitivity of the GCA RAM-1 photometer to water droplets in the respirable size range was determined. Three additional studies were also made in this program. First, an experimental study was performed to ascertain the effect of crosswind, cyclone orientation and particle size on particle sampling and penetration through the 10 mm Dorr-Oliver cyclone. Second, a theoretical study was conducted to refine the theory used to predict the particle collection characteristics of impactors. Third, filter samples with known quantities of diesel and coal particles were produced and delivered to the B. of Mines for testing a Raman scattering analysis technique to discriminate diesel particles in the presence of coal dust.

Jan 1, 1984

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By Robert S. Becker

The results of a laboratory investigation of coal cutting mechanics and noise is presented. These experiments were performed using a linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts is ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to Formulate analytical models of the coal cutting forces and noise. The analytical model For coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as Provide benefits to other important areas of underground health and safety.

Jan 1, 1980

By Laxman S. Sundae

In the vast majority of American coal mines, roof bolt holes are drilled dry, mainly because of mine operator concern with the spent water creating adverse working conditions. Wet drilling, however, can increase drilling rates and the effective lifetime of the drill bits used. This study, carried out as part of an ongoing cooperative research program between the U.S. Bureau of Mines and the University of Missouri-Rolla, shows that the large volumes of water conventionally used in wet drilling are not necessary, and the performance benefits from wet drilling can be achieved with total volume flows on the order of 0.4 L per hole. This conclusion is validated based on the measured respirable dust generated in drilling Berea sandstone. The results are confirmed using a variety of bit shapes, which are also shown to have a significant effect on penetration rate.

Jan 1, 2010