Search Documents

By J. M. Stuve

Low temperature and high-temperature calorimetric measurements were made by the Federal Bureau of Mines on high-purity samples of Re02(s) and Re03(s) to determine heat capacities and enthalpies. The temperature range of heat capacity measurements was 5 to 310 K for Re02 and 8 to 309 K for Re03. High-temperature enthalpy measurements alone were determined for pure Re207(s,1). The derived standard entropies are S°298 = 11.43±0.01 cal/deg mole for Re02(s) and S298 = 16.55±0.02 cal/deg mole for Re03(s). High-temperature enthalpy equations expressed in calories per mole are as follows: Re02 (s) , H-H298.15 = 16.002T + 1.600 X 10-3T2 + 3.522 X 105T-1 - 6,095 (298 to 1,400 K); Re03 (s) , H-H298.15 = 20.293T + 3.238 X 10-3T2 + 3.950 X 105 T-1 - 7,664 (298 to 1,000 K); Re207 (s) , H-H298.15 = 38.437T + 10.309 X 10-3T2 + 4.315 X 105 T-1 - 13,824 (298 to 413 K); Re207 (s) , H-H298.15 = 30.181 + 17.713 X 10-3T2 - 10,612 (413 to 600 K) ; Re207 (1) , H-H298.19 = 66.101T - 10,092 (600 to 700 K). Gibbs energy of formation (?Gf°) data and related functions over the temperature ranges investigated are tabulated for the three oxides.

Jan 1, 1976

By John Ward Smith, Neil B. Young

Shale specific - gravity to oil - yield relationships were developed for black shales of the New Albany Formation of Kentucky from data collected on core samples representing the complete section of the formation in three counties . Linear equations for estimating oil yield from measured specific gravity and for estimating specific gravity from measured oil yield were shown to be applicable within small error limits to all the sites tested . Variation in pyrite content is the largest source of error .

Jan 1, 1964

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By P. C. Good

High-purity chromium was prepared in massive form by the electrolysis of chromium trioxide solution at high temperatures. The metal thus obtained, containing 50 to 150 p.p.m. of oxygen, 20 p.p.m. of nitrogen, and traces of metallic impurities, could be hot-worked to rod and sheet and drawn to wire ductile at room temperatures. Optimum concentrations and operating conditions were established for the deposition of chromium from chromic acid baths containing sulfate, fluoride, and silicofluoride ions. Current efficiencies of 13 percent were attained with baths containing sulfate ion, and efficiencies of 40 to 44 percent with baths containing fluoride and silicofluoride ions. Cation exchange resins were used for removing metallic impurities from chromic acid solutions containing sulfate ion; solutions containing fluoride and silicofluoride ions were purified by recrystallization.

Jan 1, 1960

By H. D. Pallister

A review of? reports and literature on the pyrite deposits at Pyriton, Ala., indicated that a large tonnage of pyrite, some of which contained a small amount of copper, had been mined and shipped to fertilizer plants throughout the South. The information contained in this literature tended to demonstrate that the ore occurred in separate lenses of greater or less extent and of varying thickness and richness in pyrite as well as in copper. The outcrop being parallel with the Atlantic Coastline Railroad and just south of it makes the deposits readily accessible for shipment. Slopes could be sunk as they were in the past in the ore body if it were of sufficient grade and thickness, and the ore could be hoisted up the slope and milled close to the slope mouth with an ample supply of water from Talladega Creek, which follows the outcrop closely.

Jan 1, 1949

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By Denise A. Herzog

The U.S. Bureau of Mines conducted a study of cyanide leach technology used in Alaska's mineral industry from 1987 through 1990. Literature and cost data were obtained for mines in the contiguous United States, Canada, and Alaska that use cyanide to recover gold and silver. The data was compiled in an effort to evaluate the economics and conditions associated with cyanide use in Alaska. This report discusses heap leaching methodology and evaluates a "typical" heap leach operation in Nevada and compares the results of the Nevada operation to an analogous hypothetical mine in Interior Alaska. Five daily tonnage rates were analyzed for both the Nevada and the Alaska operations to evaluate the spectrum of economic possibilities. The discounted cash flow rate of return (DCFROR) for each production rate was then evaluated in terms of recoverable metal value (RMV). The Nevada RMV for each production rate was then compared with its Alaskan counterpart, and the results averaged. The Alaskan production costs are an average of 1.71 times greater than costs associated with mining in Nevada at a 0% DCFROR. At 15% DCFROR, costs in Alaska are 2.01 times greater than those in Nevada. Costs are higher in Alaska because of the shorter leaching season, increased labor and transportation costs, and heavier precipitation and vegetation.

Jan 1, 1991

By N. Greninger

The Bureau of Mines examined the possibility of a seasonal variation of respirable dust concentration in U.S. coal mines. The first step was to review company and MSHA-inspector dust samples that had been collected during the past several years in 14 selected mines for compliance purposes. Results indicated severe scatter in data; most standard deviations of the dust concentrations measured in winter and summer months were comparable in magnitude with the mean values of dust concentrations for the seasons. Therefore, a detailed statistical analysis was conducted. At the 90% confidence level, the company samples of three mines had winter means 0.15 to 0.54 mg/m3 higher than the summer means; six mines had negligible seasonal variations; and five mines had winter means that ranged from higher to lower than the summer means. Inspector data, however, were too sparse for analysis. In view of both the low frequency of occurrence of a seasonal effect and its wide scatter in several of the mines, the study was ended with the conclusion that seasonal varia-tion in respirable dust levels, in general, is an insignificant factor.

Jan 1, 1986

By Raymond B. Ladoo

Cne of t·: . .:: i::,portt recent developrr.ents in the feldspar industcy l:.a.s beer. tl:.e r,:ipid. rise of Ne·N H.v-:psr.ire as a. feldspar producing State. Tl:.e unusual size and purity of t: e deposit now 'being worked ne3.r Keene, and tr.a i.nproved metl:.ods ot:' rr.ining srd ir,illing used l:.ave been responsible foe tt.is situation. ti'eldsp'.:l. w'ls occ':tsiona.lly produced sorr.e ye1rs ago in srr.a.ll (tuantities in New Hrunpshi :e, but t::.e State had not been considered a producer of" feldspar ui til lS3l. In the s::ring of tr .. at yea!', t:.e '[eane iic Products co. of Keene, N.H., beg3Il in a srr.9.ll way tl:e production of feldspar fro:n t1eir property in Gilsum, H.H., whicr. l-.a.d long been opera.tei a.s a :tl.ca mine. The purity of the feldspar at enoe '\ttracted f''.lvorai)le attention. and tt.e production of crude ore rapidly in­ cre'.\sed. Early in 1922, a new company, t'he Golding-Keene Co,

Sep 1, 1922

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By ALICE V. Petar

Among the rarest of the rare metals are four that are linked together by a common historical background as well as by chemical relationship. With the excep- tion of indium, these metals are likewise characterized by the patriotic nature of the names given them by their discoverers. The existence of gallium, germanium, and scandium, was predicted by the Russian cherist, D. I. Mendeleeff some time prior to their discovery; and these elements might well have been overlooked, had not the search been stimulated by the urge to confirm the scientific hypothesis of their existence. Nowhare found in sufficient quantities to attract attention, these little known elemente are nevertheless widely distributed in the earth's crust. So far they are found commercially mostly in the sulphide ores of zinc and must be considered as being largely curiosities of the zinc smelter. Recent progress in electrolytic zinc refining, however, now gives promise that the way may be open for the recovery of these very rare metals in larger quantities-- possibly in quantities sufficient to permit of their finding commercial utilization.

Nov 1, 1930

By Thomas C. Denton

The Old Reliable copper mine was first examined by Harlow D. Phelps , an engineer of the Bureau of Mines , in October and November 1942 , in compliance with a request from the War Production Board , which furnished copies of assay maps of the 100- and 200-foot levels and requested that they be check-sampled . The author and R. li. Grantham and W. D. Hughes , engineers of the Bureau , made a second and more detailed examination later , after a number of manways had been opened that were inaccessible when the first examination was made .

Feb 1, 1947

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

By John Campbell, E. S. Baker, G. W. Jones

"INTRODUCTION In previous reports 5,6./ results were given showing the amount of natural ventilation that takes place in manholes (capacities, 74.1 to 308 cubic feet) when the number of ventilation openings in the manhole cover ranged from no openings to a maximum of 4g.The tests warranted the general conclusion that the ventilation or air changes taking place in, a manhole increase as the area of openings in the cover of the manhole is increased, and are proportional (with the exception of a few erratic tests) to the area of the openings in the cover. The area of the openings was the chief factor that affected ventilation.The results did not show any marked change in rate of ventilation due to increased capacity or shape of manhole, when the results were expressed in terms of air changes per day versus area of ventilation openings in square inches per 100 cubic feet of manhole space.It was observed during these investigations that in certain tests that showed erratic results (that is, did not agree with the general average for a given set of test conditions) the wind velocity during the test period was also abnormal. In view of these findings it was decided to conduct a series of tests in which the wind velocity across the openings in the manhole cover could be controlled accurately to determine the effect of wind velocity on ventilation rate."

Aug 1, 1938

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors' rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees' fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By H. G. Iverson

The purpose of this investigation was to beneficiate the Talladega gray iron ores by flotation. A component of the problem was the determination of the degree of beneficiation possible by flotation as well as the relative selectivity of certain reagents in promoting flotation of either the iron minerals or the siliceous gangue minerals. The scope of the present investigation involved only the use of small-scale laboratory equipment. Treatment by roasting and magnetic separation was not included in this study, inasmuch as a similar comprehensive investigation was completed and the results were published by the Bureau of Mines in 1927. The results of the work on Talladega iron ores are briefly summarized in this report. In the search for efficient and economic methods of beneficiating low-grade iron ores, the flotation process is among those that are receiving considerable attention. The Talladega ores are of particular interest for a flotation study, because they contain two iron minerals (magnetite and specular hematite) that are somewhat dissimilar in their flotative response.

Jan 1, 1949

By Virgil A. Marple, Susanne V. Hering

"5.1 IntroductionTraditional impactors do not offer much size resolution for submicrometer particles; typically their finest size cut is around 0.4 µ.m. Yet for many aerosol applications it is useful to be able to size segregate aerosols in the size range below 0.4 µ.m. Diesel emissions, welding fumes, cigarette smokes and photochemically generated smog aerosols typically exhibit mass median diameters between 0.1 and 0.6 µ.m. When sampling these aerosols with a traditional impactor, fifty percent or more of the aerosol mass can penetrate the final impactor stage. Allhough the material can still be collected on a backup filter, the filter gives no size resolution. As a result, the investigator has no size information on a substantial portion of the sample. One needs a sampler that size-segregates the majority of the aerosol mass. A lower size cut of 0.1 µ.m or less is required for most combustion smokes and smog aerosol s.To obtain smaller cutpoints two types of impactors have been developed, namely low-pressure impactors and micro-orifice impactors. Both instruments can provide cutpoints as small as 0.05 µ.m. Low-pressure impactors were introduced more than twenty years ago (Stem et al., 1962), and a variety of these samplers are in use today. Micro-orifice impactors have been developed at the University of Minnesota within the last five years (Marple et al., 1981 ). To date theirs are the only examples of these instruments in use.5.2 Operating PrinciplesThe low-pressure and micro-orifice impactors use two different approaches to achieve their very small particle-size cuts. Low pressure impactors resemble ordinary impactors, but are operated at reduced pressures of 5-40 kPa (0.05 - 0.4 atm). They take advantage of the decreased aerodynamic drag on particles that occurs when the mean free path in the air is as large or larger than the particle diameter. Micro-orifice impactors operate at near atmospheric pressure, but employ very small orifices, 40 µ.m to 200 µ.m in diameter. The streamlines of the air impinging upon the impaction plate have correspondingly smaller radii of curvature; the air is accelerated more quickly, making it more difficult for the particles to follow. The basic operating principles for both types of impactors are evident from the particle Stokes number, defined as:"

Mar 1, 1989

By W. H. Kerns

The Critchfield manganese deposit, Huntingdon County, Pa., was investigated by the Bureau of Mines in October 1942. Iron ore was mined from an open cut just southeast of the manganese deposit about 80 years ago. The Critchfield Sand & Feldspar Co. was operating (1942) a clay-mining and beneficiation plant northeast of the manganese deposit. The Bureau completed six rotary bucket-drill holes and three hand-auger holes, aggregating 370 feet on the deposit. This report describes the work performed and presents the results obtained.

Jan 1, 1948

By John Taber, JOHN B. HOPKINS

During World War II , a critical shortage of domestic abrasive corundum developed . Late in 1944 , the shortage became so acute that it was deemed advisable to investigate certain low-grade corundum prospects in Madison and Gallatin Counties , Montana . The Gallatin , the Bozeman , and the Bear Trap deposits were the principal ones investigated . The Bear Trap deposit was examined by E. W. Newman and Robert S. O'Brien , engineers of the Bureau of Mines , in August 1944. Exploration was started in October 1944. Field work was completed late in the spring of 1945 . report presents the data obtained from the exploration .

Mar 1, 1947

By C. H. Riggs

This report presents pertinent data on all active water-flooding projects in Washington County, Okla., and describes in detail the operation and production history of five representative floods. The flooding of partly depleted oil-bearing sands to produce petroleum that would not be recovered by other methods is becoming increasingly important to the oil industry. In 1942, two water-flooding projects in Washington County produced 35 barrels of oil daily from 90 developed acres. In March 1951, 4,000 barrels of oil was being produced daily by the injection of 58,000 barrels of water on 19 active projects covering 1,645 acres. Several projects are being extended, and new operations are being initiated. Figure 1 shows the location of the active water-flooding projects in Washington County. The yearly oil production from Washington County increased from 1,076,000 barrels in 1948 to 1,720,000 barrels in 1950, owing principally to the effects of water flooding. To March 1951, permits to flood more than 8,000 acres in Washington County had been granted by the Oklahoma Corporation Commission.

Jan 1, 1951