Search Documents

By W. M. Myers

"The continued expansion of modern industry broadens the markets for minerals and their product. With these increasing demands new uses are being found for minerals that heretofore were considered as possessing no commercial possibilities. This tendency is reflected in the nonmetallic field in a constantly increasing demand for minerals formerly considered to be of scientific interest only, Furthermore, nonmetallic minerals of established commercial importance are used in new ways in various products, and this tends to expand the markets for these minerals. Some recent outstanding developments in applications of minerals are given in the following pages.The Andalusite GroupAmong the minerals that until recently were considered of scientific interest only, may be listed those of the andalusite group. This group is composed of the three minerals, andalusite, cyanite (or kyunite), and sillmanite, which are all forms of the compound Al2SiO5 (A1203, S1O2), and are therefore identical in chemical composition, but differ in physical properties,"

Mar 1, 1924

By K. C. Dean

Horizontal and vertical air classification systems were tested individually and in simulated tandem use for the recovery of ferrous and nonferrous metals and of other noncombustible and combustible products from shredded urban refuse. The horizontal air system with a larger tonnage throughput was used to obtain preliminary separations, and a smaller capacity vertical system was used as a cleaning device. Air elutriation, magnetic separation, and screening of shredded minus 6-inch municipal refuse recovered 92 percent of the metal in a relatively clean iron product contaminated only by adhering coatings or entrapped materials, recovered 97 percent of the combustibles in a 97-percent combustible product, and rejected 88 percent of the nonmetal noncombustibles. Cleaning of the preliminary combustible fraction produced a 98-percent paper product while rejecting other combustibles (plastics, rubber, textiles, etc.) into a 94-percent combustible product. Retreatment of the preliminary noncombustible fraction produced a relatively clean glass product.

Jan 1, 1971

By S. R. B. Cooke, J. Bruce Clemmer, Will H. Cognill, F. D. DeVaney

"INTRODUCTION The domestic production of potash has made rapid strides in the past 4 years. In 1929 the United States produced 109,820 tons of potash-bearing material, equivalent to 61,590 tons of pure potash (K20). In 1933 to this had increased to 331,110 tons, containing 143,378 tons of potash, due chiefly to the development of the potash deposits near Carlsbad, N. Mex. The potash ores of that district occur at a depth of about 1,000 feet and as mined consist of a mixture known as sylvinite containing about 40 parts of sylvite (KC1) and 60 parts of halite (NaCl). By careful mining the extraneous material does not amount to more than 2 or 3 per cent. Such ore was used in the experimental work here reported.The usual chemical method for the recovery of potash from sylvinite, while efficient in the production of pure potassium chloride, requires,expensive equipment and is costly to operate. It occurred to the Bureau of Mines that ore-dressing methods, which have been applied to other nonmetallic minerals, might be adapted for the production of a grade of potash suitable for the fertilizer industry. After preliminary study by the Bureau of Mines showed that ore-dressing treatment was possible the investigation was extended under a cooperative agreement between the U.S. Bureau of Mines, the Potash Company of America, and the Missouri School of Mines and Metallurgy, Rolla, Mo.ACKNOWLEDGMENTSAcknowledgment is here given for valuable assistance in the laboratory of R. G. O'Meara, assistant metallurgist. U.S. Bureau of Mines, Tuscaloosa, Ala. who was on detail at the Rolla station during the early work; by E. W. Gieseke and Albert Ollar, temporarily employed by the Potash Company of America; and to N. H. Lenz, an engineer temporarily assigned to the station."

Feb 1, 1935

By Kenneth E. Hay

The Bureau of Mines collected coal and coal waste aggregate material from two different mine sites to determine their strength characteristics for use in concrete. The concrete would be placed underground as support walls for ground control in adverse conditions or unique mining applications. A standard mix design was established for a "wet" mix using a water-to-cement (w/c) ratio of 1.0 to facilitate pumping into place. Later, material was collected from four more mine sites and used to make 2-by 2-by 2-ft test blocks with the same w/c ratio. A pull-out cone device and borehole shear tester were used to determine the in situ material strength of the test blocks. These techniques will provide a simple and quick way of determining support wall strength in an underground environment. Test results from the pullout cone de-vice showed a good correlation of 0.98 to test cylinder compressive strengths of the same mix. Results of the borehole shear tester were inconclusive.

Jan 1, 1986

By C. V. Davis

In the lnvestlg::ìt1on of mAthods for aSS8.7ing platin",. conducted by the Bureau ot MinAs, reoent experiments have d~velopad tha~ with ce..tain orei, especially when thr, quantity Of platinum 1s eonlidarablfl, nit'!le acid w111 not etfßct a iepard-Han of platinum and pa11adium. 'lhe following m;lthod has been found to be accurate and to reiu1 t in a complete S''lun''ation of' th~3:l metals. It is therefo 1" '!eeommei:ed that 1 t ba followed rath::r- than the method of separation with nitrio acid, givèn in Technical Pape'! 270.* At line 22, pagi 14, of that paper, bAglnnlng with ~tarm th,~ metals '.'ith dilute¡ nitrio acid," strikE out the rest of the paragraph, and substttutt~ the pro_t cedure g1 ven below. ?lunder and Thuringer.. have developed mnt¡iods for th"i sflparation of palladium from all the platinum metals exoept platinum bj m ,ans of dlmethy- 19lyoxlme. They state that the~ is no action for several hours if an excess of dimeth¡lglyoxime is added to an aqueous solution of ohloroplatinic acid in the cold, alio that only on boiling is the platinum pTecipi ated ¡~d than only PST't of the platinum i srenoved from the sUut1on. They found that palladium 1s p~ecipi tated quati tat! vely in the oold as (CaH 4N40 Pd) which is insoluble tn water, dilute hydroohlorio acid, dilute acetIc aofd or in 50~ ethyl alcbhol. All of their pT'90ipi tations we~p Carl". ied out ~hile the solutions were being heated. This caused a pal"tia~recipltation of the platinum along wi th the

May 1, 1922

By Carlton E. Brown, William P. Yant

"INTRODUCTION Direct visual microscopic determination of particle-size distribution and number concentration of atmospheric dust is time-consuming and trying to the eyes. By using the microscope to project images of the particles at high magnification onto a screen much of the eyestrain can be eliminated and particle-size distribution results obtained with less effort and at a considerable saving in time. It also permits simultaneous observation of the images by more than one person. Microprojection requires no more skill and very little more apparatus than is required in the use of the microscope. Anyone familiar with the microscope should be able to obtain as perfect images on the projection screen as in direct visual microscopy since the same laws and limitationsThe theory and practice of microprojection are described in detail in texts. 5/6/ The procedure has been used and found to be satisfactory for measuring the particle-size distribution of sub-sieve-size substances, such as pigments and powder 7/8/ in the same size range as that of atmospheric dust. The Bureau of Mines has used the microprojector and found it to be quite satisfactory for (1) the determination of the number concentration of atmospheric dust R.I. 3289 in samples collected by the Owens jet dust counter; (2) particle-size distribution in samples of atmospheric dust collected by the Owens jet dust counter and by the electric precipitator; and (3) the particle-size distribution of dusts, blood cells, bacteria, and pollen. Work is in progress at this Bureau on the use of the microprojector in counting impinger samples. The use of different kinds of illumination, such as reflected (dark field), polarized, monochromatic, and ultraviolet, in the projection of images of atmospheric dust particles is being considered."

Oct 1, 1935

By D. B. Starkey

Investigation into the expressions of the field produced by a loop over a conducting half space or in an infinite conducting half space are well documented. Reasonably complex descriptions of the effects of stratification also are reported. However, a model which must contain all of these complexities because of transmission to depths of 15,000 feet and also include the pertibation of the field by a verticle cylindrical steel casing loses its facility in the field or for quick, accurate approximation to field magnitudes and phase. This paper describes the results of two field tests to determine the attenuation and phase versus depth and frequency of an electromagnetic wave (induction field). A simple two-layer model is postulated to predict the magnitude and phase of the induced field which does not require sophisticated computing tools. Correlation of the model with experimental results show agreement of most amplitude measurements to within 3 db and most phase measurements to within five degrees. The tests were conducted in a 7400 foot deep well in Nevada and an 11,000 foot deep well in Wyoming which had conductivities ranging from .0025 mhos/m to .25 mhos/m. The surface transmitting dipole had an area of ~ 10 6 feet squared and constant frequency signals of 1.5 Hz to 20 Hz were transmitted through the earth utilizing less than 65 watts of power. Model Description The magnetic field intensity components generated by a magnetic dipole immersed in an infinite homogeneous medium can be expressed in spherical coordinates as: [ ] where N, I, and (p a ) are the transmitting antenna turns, current, and effective area, respectively, and r is the range from the loops circumference to the measurement point. The case of interest for these experiments, however, is the special case of coaxial dipoles, i.e., ? = 180° . For this case H?= 0 and H reduces to: [ ]

Jan 1, 1973

By V. P. Bhavanandan, S. B. Dubbs

The mucus secreted in the respiratory tract provides the first barrier against inhaled particulate and gaseous toxicants. The major component of mucus which is responsible for the physical properties and protective functions of the respiratory mucus is mucin. We have initiated investigations to determine the effects of coal mine dust on the synthesis of respiratory mucin by rat trachea under in vitro and in vivo conditions. In this study we have established optimum conditions-:ro-r~ the asceptic growth and mucin secretion of rat tracheal explants in culture. The best outgrowth of ciliated epithelial cells and maximum mucin production was obtained in CMRL 1066 medium containing 10% fetal calf serum. The explants continued to secrete mucin even after three weeks in culture. For the estimation and characterization of mucins the tracheae were cultured in the presence of [3H] glucosamine and [35S] sulfate or [14C]leucine. The mucins were isolated from the medium by gel filtration, treatment with hyaluronidase, ion exchange chromatography and CsBr density gradient centrifugation. Precipitation of polyanionic material in the culture media with cetyl pyridinium chloride and fractional extraction with NaCl also yielded mucin free of glycosaminoglycans, but in low yields. The tritium label in the purified mucin was distributed in sialic acid (50%) galactosamine (37%) and glucosamaine (13%). The density of purified mucin as determined by CsBr gradient centrifugation was about l.43g per ml in comparison to l.46g per ml for human respiratory mucin with a carbohydrate content of about 80% by weight. Alkaline borohydride treatment released saccharides which contained about 80% of the radioactivity. The effect of adding varying amounts of coal dust to the culture medium is under investigation. (Supported by U.S. Bureau of Mines Grant G1135142, Project 4210).

Jan 1, 1989

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Ahmed, M.,• "Development of an Integrated Control System for Mine Ventila¬tion and Firedamp Drainage," Mining Engineer, Vol. 127, No. 91, April, 1968, pp. 382-392. Andrews, J. W., "U. S. Mine Ventilation Standards," Paper presented at the International Mine Ventilation Congress, Sept., 1975. Boyle, J. A., and Conn, 0. S., "The Control of Mine Ventilation Utilizing Multiple Main Fans," Paper presented at the Seventy-second Annual CMIA Meeting, Pittsburgh, December 1958. Collinson, P. L., and Vance, W. E., "Mine Ventilation Planning," The Mining Engineer, Volume 121, No. 14, 1961, pp. 141-156. Committee on Industrial Ventilation, Industrial Ventilation, 12th Edition, 1972. Grever, R. E., "Automatic Monitoring of Ventilation Conditions in European Coal Mines," Symposium on Engineering Systems Design for Mine Safety, Michigan Technological University, August 1973. Hall, C. J., Airflow in Mines - Thermodynamic and Motive Column Analyses, The Book Concern, Printers, Inc., Hancock, Mich., 1967, 263 pages. Hargraves, A. J., "Planning and Operation of Gaseous Mines," Canadian Mining and Metallurgical Bulletin, Vol. 66, No. 731, March 1973, pp. 119-128. Harris, E. J., "The Fluid Network Analyzer as an Aid in Solving Mine Ventilation Distribution Problems," SME-AIME Transactions, Vol. 228, 1963, pp. 391-395 Higgins, J., and Shuttleworth, S. E. H., "A Tracer Gas Technique for the Measurement of Airflow in Headings," Colliery Engineering, November 1958, Vol. 35, pp. 483-487. Kaiser, K. M., and Bhowmick, B. C., "Recent Developments in Mine Ventila¬tion Instrumentation," Journal of Mines, Metals & Fuels (INDIA), June 1974, pp. 155-162. Kalasky, J. D., and Krickovic, S., "Ventilation of Pillared Areas by Bleeder Entries, Bleeder Systems, or Equivalent Means," Trans¬actions AIME, Volume 254, December 1973, pp. 284-291. Mahajan, J. K., "Ventilation Planning for a Deep Metal Mine," Min. Geol. Met. Inst. India, Volume 69, 1972, pp. 31-38.

Jan 1, 1977

By Maria I. De Rosa

The major fire and fire injury findings for all coal mining categories for 1990-1999 are reported in tables 37-38. Table 39 and figure 13 show the number of fires. fire injuries, risk rates, employees' working hours, and coal production (under- ground and surface coal mines only) by time period for all coal mining categories. Table 40 shows major findings (for under- ground coal mines only) for 1978-1992. For all coal mining categories, 458 fires occurred during 1990- 1999; 157 of those fires caused 164 injuries and 2 fatalities (Ewhr = 2,070 x l0%r, Irr = 0.016: C'P (for underground and surface coal mimes only) - 10,363 x l0\t, Frr = 0.044, LWD = 14,753). Twenty-nine fires and 17 injuries involved contractors. Sixty-six fires required firefighting interventions by mine rescue teams (25 times in underground mines) and fire brigades and fire departments (at least 41 times at surface coal operations). In all, 51 fires destroyed or heavily damaged equipment (including 16 pieces of mobile equipment) because of failure of other firefighting methods, late fire detection, undetected fires, or fire size. A total of 114 fires were detected late, and 42 fires were undetected. The greatest number of fires and fire injuries occurred at surface coal mines; the highest risk rate values were also calculated for this category. For all coal operations, the ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flames (1 03 fires or 23% with 69 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (98 fires or 2 1 % with 29 injuries), spontaneous combustion/hot coal (62 fires or 14%), electrical short/arcing (49 fires or 11% with 18 injuries), and conveyor belt friction (3 1 fires or 7% with 6 injuries).

Jan 1, 2004

By Alvin Schallis

Of all the uses for dolomite that depend on its magnesia content, perhaps the most important is its use in basic refractories. The quantities of dolomite (including both that used as crude and that calcined before use) sold or used for refractory purposes by producers in the United States for 1920-41, inclusive, are shown in figure 1. As can be seen from the chart, the utilization of dolomite as a basic refractory is far from new; it was, in fact, the first basic refractory used extensively in open-hearth steel furnaces. After large deposits of magnesite were opened in Austria-Hungary, the use of dolomite in the open hearth declined somewhat, only to be actively revived during the World War of 1914 to 1918, when supplies from Austria were shut off. The use of dolomite as a refractory in the steel industry again declined slightly for a brief period after the Armistice, but subsequently its use has tended steadily to increase, latest statistics indicating that more dead-burned dolomite is used per ton of open-hearth steel now than during the World War of 1914 to 1918. Despite fluctuations in consumption, dolomite has continued to be by far the most widely used basic refractory material. The following table, showing the quantities of basic refractories consumed in the manufacture of steel, the principal outlet, indicates the relative importance of dolomite. The chief reason for the widespread use of dolomite as a basic refractory is its relatively low cost. Its abundance and the proximity of the deposits to the steel industry (see fig. 2) afford every incentive to enhance the desirable physical properties of dolomite refractories and to ameliorate certain of their less desirable characteristics. The present emergency, with its huge demands upon the steel industry, has lent further impetus to the work of improving dolomite refractories.

Jan 1, 1942

By John W. Buch

In 1947, a Korfmann universal shearing machine was installed in a mine in the Southern field of the Pennsylvania anthracite region. The machine was obtained from Germany by the Bureau of Mines after the close of World War II as a part of a program of experimental work to increase the output and lower the cost of anthracite, which the Bureau of Mines initiated in 1944 when an agreement was made with an anthracite-producing company for use of one of the company's mines as a testing ground for certain mechanical equipment procured or developed by the Bureau. A major objective is to develop a mechanical mining method that will increase the rate of advance and reduce the coat of development of coal gangways in steeply pitching seams. In addition to the time to be saved in driving these openings by machine, it is felt that further economies will be affected by making it possible to concentrate producing sections into smaller compass and that savings will ensue in supervision, maintenance, and time required for mining a section. A higher percentage extraction also is an objective. Test work covered by this report was concentrated on the power characteristics, maneuverability, effectiveness, and general qualities of the Korfmann machine in cutting coal, the cutting tests representing the first use of a machine of this kind in steep-pitch mining in the United States.

Jan 1, 1951

By Lucien Eaton

This paper describing the mining practices at Mine No. 2 of the Marquette Range, Michigan is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various minim; districts of the United States. The publication, of this information should be of interest to the industry at large and the exchange of ideas thereby made possible should be of economic value to operators in all harts of the country. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of the property discussed in this paper for much of the information presented. The geological classification is taken from publications of the U. S. Geological purvey.

Jan 1, 1929

By George H. Schnakenberg

Automation of coal mining activities at the face offers improvements in worker safety, health, and productivity. Introduction of integrated computer-sensor systems to current mining machines will enable these machines to perform some of the most hazardous tasks through supervised teleoperation. The U.S. Bureau of Mines is pursuing the development of the enabling technology necessary to achieve this goal. The research program consists of both basic and applied research, each focused on the fundamental issues of computer and sensor technologies. Short-term research is directed to providing computer-assisted, remote supervisory operation of present underground equipment; the long-term goal is the development of progressively more intelligent mining systems. The research program includes a review of robotic machine and autonomous vehicle technologies and of current mining technology, which provides a base for developing innovative mining methods; research in navigation and guidance technology, emphasizing control of a continuous mining machine; research on coal-rock interface sensing technology for horizon control, and rib thickness control in highwall mining; the development of computer systems and hierarchical architectures for real-time control; and development of expert systems for machine system fault diagnostics and predictive maintenance. This report presents a brief background and the current status for each of these research areas.

Jan 1, 1989

By Eric G. Zahl, John P. Dunford, Hamid Maleki

Coal bumps are influenced by geologic conditions, the geometric design of coal mine excavations, and the sequence and rate of extraction. Researchers from private industry and government agencies around the world have studied mechanisms of violent failure and have identified individual factors that contribute to coal bumps. To develop predictive tools for assessing coal bump potential, the authors initiated a comprehensive study using information from 25 case studies undertaken in U.S. mines. Multiple linear regression and numerical modeling analyses of geological and mining conditions were used to identify the most significant factors contributing to stress bumps in coal mines. Twenty-five factors were considered initially, including mechanical properties of strata, stress fields, face and pillar factors of safety, joint spacings, mining methods, and stress gradients. In situ strength was estimated in 12 coal seams where uniaxial compressive strength exceeded 2,000 psi. Allowances were made for favorable local yielding characteristics of mine roof and floor in reducing damage severity. Pillar and face factors of safety were calculated using displacement-discontinuity methods for specific geometries. This work identified the most important variables contributing to coal bumps. These are (1) mechanical properties of strata, including local yield characteristics of a mine roof and floor, (2) gate pillar factors of safety, (3) roof beam thickness, joint spacing, and stiffness characteristics, which influence released energy,(4) stress gradients associated with the approach of mining to areas of higher stress concentrations, and (5) the mining method. By combining the strength of both analytical and statistical methods, new capabilities were developed for predicting coal bump potential and for building confidence intervals on expected damage.

Jan 5, 1999

By R. V. Ramani, B. K. Belle

The increased effectiveness of a two-phase spray system (TPSS) over a single-phase spray system (SPSS) for dust suppression is reported in several laboratory studies. The dust collection efficiencies of SPSS and TPSS were studied in a model experimental longwall gallery facility at Pittsburgh Research Laboratory at NIOSH (USA). The experimental design consisted of two factors: pressure, and airflow. Each factor had three levels. SPSS experiments were conducted at only one pressure (1035 kPa) which is nearly 1.5 times higher than the highest air and water pressure for TPSS experiments. The results of the study are presented in this paper. While it appears that TPSS performed better than SPSS, the data is not sufficiently conclusive on this aspect. The differing spray characteristics of the chosen TPSS and SPSS nozzles did not allow a direct comparison of the two systems. In the TPSS arrangement, considerably greater turbulence in airflow is created around the shearer; it is likely that at least in the immediate vicinity of the tailgate drum, there is a roll back of the dust/mist cloud into the walkway. Therefore, positioning of the personnel upwind of the tailgate drum is necessary to avoid high dust exposures. The rate of decrease in concentration with TPSS is higher than that with SPSS. This may be due to the greater atomization of the water. The test set-up did not allow the study of conditions when coal is cut from tail to head where the potential for personal exposure is high. Changes in the experimental design are necessary to overcome some of the reasons expected for the inconclusive results.

By Kevin Connor

During 1984, minerals exploited in Burundi included gold, kaolin, lime, and peat. Over 1,100 troy ounces of gold was extracted and traded during the year as a result of the lifting of the Government ban on gold mining in mid-1983 and the establishment of an artisan mining program and licensed trading counters. Almost 2,000 tons of kaolin was mined for the manufacture of insecticides. Lime production was for domestic fertilizer applications. Amoco International and the Government signed an accord late in the year for a petroleum exploration program covering 600,000 acres of Burundi's onshore Ruzizi Plain and part of northeastern Lake Tanganyika. Amoco was expected to begin the exploration program by mid-1985. Anticipated program costs could run as high as $200 million.2 The Finnish company Ekono Oy completed its peat industrial energy development studies for the Buyongwe peat deposits of northern Burundi by the end of the year. The project assessed the quantity and fuel quality of 13,000 hectares of peatland and was part of a larger study for developing the Musangati lateritic nickel deposits of Burundi, estimated at 3% of the world's reserves of nickel. The Buyongwe peat would fuel dryers and an electrical generating plant for supplying power to nickel ore processing facilities. Briquetted peat would also be used as a substitute for wood and charcoal, presently the main sources of rural energy in the country and rapidly depleting because of deforestation. The study also evaluated the most economical methods to harvest the peat bogs. The study was financed by the International Development Association (IDA), United Nations Development Program (UNDP), Finnish Aid-Finnida, and the Burundi Government.

Jan 1, 1986

By Roy L. Wilfong

The linear expansion of high-purity oxides of yttrium, cerium, samarium, europium, and dysprosium was determined by the interferometric method for the temperature range 25° to 1,000° C. Single-crystal magnesium oxide and single-crystal aluminum oxide were used as reference materials. The bulk density and crystal form of the nonreference materials also were determined. The coefficients of linear expansion in the range 25° to 1,000° C were found to be 8.10 x 10-6 for yttria, 12.10 x 10-6 for ceria, 10.81 x 10'6 for samaria (monoclinic), 10.35 x 10-6 for europia (monoclinic), and 8.13 x 10-6 for dysprosia, each given in centimeters per centimeter per degree Centigrade. A detailed investigation of the interferometric technique for measuring thermal expansion in this temperature range was made. The interferometer was found to be a precise tool but only when adequate precautions were taken. These precautions are described.

Jan 1, 1963

By THEO L. JOHNSTON

In preparing for war , Japan built an iron and steel industry that ranked high with other industrial nations . Deficient in raw materials for making iron and steel , it had to acquire the bulk of its iron ore and much of its coal and scrap iron from foreign sources . Steel manufacture, and fabrication , however , were reserved mostly for the Home Islands , where modern integrated plants produced the implements of war . The vulnerability of relying on imports during the war was recognized early, and steps were taken to exploit iron-ore deposits and develop treatment processes on the Home Islands in order to be as self - sufficient as possible . Although the industry had expanded considerably, the capacity of the large plants still was insufficient for military requirements, so other meth- ods of producing iron and steel were adopted, which in some ways illustrate the desperate effort made to supply the war machine. In developing the iron and steel industry, modern practices of other countries were studied and followed with modifications to suit Japanese con- Aitions. German and American technical ability and equipment played a large part in the program; however, the Japanese had competent furnace technologists capable of obtaining proper equipment performance. For the most part, the standard practice consisted of smelting iron ores in blast furnaces and then refining the pig iron to make steel in open-hearth furnaces. Electric furnaces played an important part, especially in the manu- facture of alloy steels. Various other methods yielded minor but significant production. Among the various other treatment processes used, the production of sponge iron in rotary kilns 'probably was the most important in producing melt- ing stock for steel making. Of special importance was the fact that sponge iron made from low-grade ores contained critical metals, such as nickel and chromium, so that the results were more significant than was generally believed.'

Mar 1, 1948

By C. W. Owning

"The Bureau of Mines has repeatedly emphasized the necessity of completely ""rock-dusting all coal mines, except anthracite mines, in every part whether in damp or dry condition."" Every open accessible part of, the, mine without exception should be thoroughly rock-dusted, including parallel entries, air courses, trackless entries, crosscuts, and rooms to within at least 40 feet of every coal face. Very few mines have followed this recommendation and warning, with the result that there have been explosions not only in mines which have not used rock dust but also in so-called rock-dusted mines. Following a number of mine explosions it has been reported that the mine was rock-dusted,"" whereas it is probable that only some of the haulage roads had been given a hurried application of rock dust and in most instances not as much as 5 per cent of the mine was really rock-dusted. That is not rock-dusting.Some conscientious, well-meaning mining men have felt that rock-dusting of haulage roads would effectively stop an explosion; however, when shown, through widespread explosions in mines ""well rock-dusted"" according to the above method, that leaving large areas undusted, furnishes paths through which a violent explosion may travel, these mining men have realized the necessity of thorough rock-dusting and have adopted this explosion-prevention method.The Mather Collieries mine, Pickands, Mather and Co., operators, at Mather, Pa., was the first mine in Pennsylvania to receive, full credit for rock-dusting under the new 'stringent ruling of the Pennsylvania Compensation Rating Bureau, the provisions of which require that:"

Feb 1, 1931