Search Documents

By J. C. Cawley, J. Sottile, J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts and make the repair. Of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner and tested. This paper summarizes the development of the diagnostic system and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Comments on the system's performance are also presented.

Jan 1, 1995

By F. H. Muge

This paper intends to present a general methodology implemented in a software package and which can be applied, whatever the exploitation methods, mining constraints and time basis, to mine planning and production schedulling. Examples are: presented covering the medium-term and short-term planning procedure and the production schedulling for two underground mines located in the South of Portugal (Neves- -Corvo and Aljustrel Mines). Both are complex suiphide orebodies with differ- ent exploitation methods (Neves-Corvo: cut-and-fill; Aljustrel: Long-hole stop- ping).

Jan 1, 1992

By S. Makni, C. Bazin, D. Hodouin

This paper reviews approaches for the real-time estimation of mass flow rates and assays using data from on-stream analyzers and flowmeters in a flotation circuit. Results obtained using one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1998

By Slobodan Vujic

Production of building materials such as are stones, sand, gravel etc., is characterized by a relatively low economic value and requires reasonable transport costs. That is why we are often faced, in our practical work, with the fact that within the framework of a relatively small area several open pits of building materials are, developed side by side while neither ecological, urban and spatial nor location factors have been taken into consideration. Numerous locations together with heterogeneous factors. point undoubtedly to the problem of planning the open pits locations for building mateials as a very serious and complex one. Even when certain localities are in question, it is rather a difficult task to present a real state and encompass all the, important location factors by mathematical model ling. This paper presents one of such models for solving the problem of selecting a location for building materials open pit.

Jan 1, 1992

By D. L. Schweyer, W. A. Munson, R. H. Hanewald

Discussed is the INMETCO processing of electric arc furnace (EAF) baghouse dusts from the specialty-steel and low-alloy industries. In addition, the INMETCO process has been modified to recover nickel, chromium and iron from many other waste materials including: •pickling solutions or filter cakes, •spent nickel and chromium plating baths, •carbon refractories from pickling tanks, and •superalloy wastes including baghouse bags. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high-temperature metals recovery. This process and the details of INMETCO's best demonstrated available technology (BDAT) test program are discussed.

Jan 1, 1993

By F. M. Doyle

Metal removal kinetics and metal ion selectivity in ion flotation were studied from a thermodynamic perspective. Surface tension data could be used with the Gibbs adsorption equation to quantitatively predict the metal-ion removal kinetics in alkylsulfate-Cu systems. However, surface tensions predicted cation selectivity coefficients in the sodium dodecylsulfate (SDS)-Cu-Ca and SDS-Cu-Pb systems rather poorly, although the predicted order of the selectivity (Cu2+ < Ca2+ < Pb2+) was correct. Another thermodynamic selectivity model, which used the Grahame adsorption equation and a geometrical analysis, predicted cation selectivity coefficients that agreed very well with experimentally measured values.

Jan 1, 2002

By Michael E. Mcllwain, Lee O. Nelson, Robert D. Rogers, James H. Wolfram

Examination of the economics and environmental consequences associated with phosphate fertilizer production documents the necessity for development of innovative production technologies. Evidence of phosphate ore&apos;s susceptibility to microbial alteration indicates that it will be an ideal candidate for industrial-scale bioseparation. There are at least two applications for the biosolu- bilization technology: (1) an industrial-scale bio- process similar to the presently used wet acid process and (2) production of small prills (bio- bead) containing unprocessed rock phosphate and the biological ingredients necessary to promote phosphate solubilization. At the present stage of development, the biobead technology is the preferred application. It is an energy-efficient "green" technology that will dramatically reduce the amount of solid waste and air emissions produced by the phosphate industry.

Jan 1, 1999

By Maureen D. Carmen, Joseph L. Zaluski, Gladys Beck Green

The Federal Surface Mining Control and Reclamation Act (SMCRA) requires a surface mine operator to post a performance bond before a mining permit can be issued to that operator. Release of that bond is contingent upon the completion of all required reclamation, restoration, and abatement work on the permit area. This paper explores the requirements of each of the three phases of reclamation under SMCRA, as well as provisions of four exemplar state regulations of four states that have been granted "primacy" under SMCRA. Successful completion of these requirements is a condition pre cedent to the release of performance bond liability. Failure to secure a timely bond release will have an ad verse impact on an operator&apos;s other mine permitting activities throughout the United States.

Jan 1, 1991

By G. Kazonich, S. L. McGill, J. W. Walkiewicz

Naturally occurring minerals and reagent-grade compounds were tested to determine their receptivity to microwave heating. The maximum temperature achieved for the samples and the time required to reach temperature are reported. A description of the microwave oven and a thermocouple technique that accurately measures and continuously records the temperature of samples during irradiation are reported. Extractive applications using the generated microwave data were investigated. Stress fracturing at mineral grain boundaries in a gangue matrix was shown. This should significantly affect grinding energy requirements and liberation properties. A method to produce a magnetic phase on pyrite surfaces, a method of using microwave heating to retort cinnabar concentrate, and a roast-leaching microwave treatment of chalcopyrite ore are described.

Jan 1, 1987

By L. R. Freitas, A. K. Resende, J. A. Oliveria, K. L. Gonçalves, L. F. D’Assumpção, L. R. Lage, J. D. Neto, F. Viveiros

Pará Pigmentos S.A. (PPSA) is an association between the Brazilian companies CVRD and CADAM, Mitsubishi Corporation of Japan, and the IFC (World Bank) created in 1992 in order to recover kaolin from Rio Capim deposit, northern Brazil. Commercial production at PPSA started in August 1996 using a process comprising mining and beneficiation at the mine site, pumping through a pipeline and drying/loading at the port site on the Amazon river estuary. Presently, all PPSA production is concentrated on 82% <2um, high-brightness coating clay shipped in bulk. In this paper, a detailed description of the development of PPSA beneficiation process is presented. The results of laboratory and pilot plant studies under- taken to develop alternative grades of clay, such as delaminated and calcined kaolins, are also discussed.

Jan 1, 1998

By M. Rosenshine, R. W. Barbaro

This paper presents a cyclic queueing model that evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumption of exponentially distributed service times and steady state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1988

By L. J. E. Hofer, L. F. Zeiler, D. A. Giardino

The Jones Trickett Ratio (JTR) is generally used in investigations of fires and explosions for the determination of the composition of the fuel. This paper takes a close look at the JTR and finds it unreliable and ambiguous for the determination of fuel composition. A new index is presented, termed the (H/C) Index which uniquely determines the fuel composition. The (H/C) Index is simple to use requiring only the results of a single gas analysis of the combustion products. Experimental data testing the (H/C) Index for methane, propane, ethylene and coal dust are given, showing that the Index unambiguously determines the composition of the fuel. The (H/C) Index is also applied to the gas analysis data of several mine fires, illustrating how the Index changes with the progression of the mine fire.

Jan 1, 1993

By V. J. Matta, A. A. Pincheira, I. A. Reghezza, Ch. J. Vergara

The growth of solvent extraction in Chile has been astonishing during the last years and has been established as a very successful technology. However, there are still limitations that must be improved, mainly, the problem of carry over from one phase to the other and the losses of organic reagent associated with the crud formation. These are problems that our company has been taking care, solving them with high efficiency and low costs, allowing important increases in the copper output of our plants and capital savings by means of the optimization of the use of nonproductive units in the SX plants.

Jan 1, 1998

This section is addressed to the computing needs of corporate (top) management which are less specialized than the computing needs of operating or divisional management described in the previous sections. It is essential that the computer be used as a tool to serve corporate management and that information and results are presented in a succinct form. A key responsibility of the manager of computer applications is to communicate well with corporate management. A common trap for computer management is to allow the development and implementation of sophisticated and academically interesting computer applications which do not enlighten corporate management in its decision-making task. Thus it is essential to devote sufficient time and effort to designing and specifying a computer system before developing and implementing the system.

Jan 1, 1979

By B Faulkner, M. Weinecke

In 1997, Sveciala began a program to develop a process to convert waste tires into valuable commodities. A review of numerous approaches revealed shortcomings that were process related or mechanical related, while some of the approaches emphasized he production of low-value products. A market study revealed that a process that could produce a good grade of carbon black would be economically feasible. This paper discusses the laboratory and pilot-plant development and commercial plant design of such a process.

Jan 1, 2002

By H. M. Lima, P. Wathern

There are many different words to describe mine closure, including rehabilitation, reclamation, restoration and decommissioning. Closing mining operations, mainly open pit mines, has required resolution of numerous issues. Mine closure plans involve environmental-protection issues, regulatory issues and community issues. The obvious, and often most expensive of them, is the physical rehabilitation of the disturbances and the elimination of long-term commitments and maintenance. This paper outlines mine closure planning and its important component, mine-site rehabilitation. Community consultation and involvement are also referred to as an important component of the mine-closure plans, which are required to ensure satisfactory mine site rehabilitation. Considerations of socioeconomic impact of mine closure and long-term responsibilities are presented.

Jan 1, 2000

By P. Berendsen

The tectonic and sedimentary environment of the Central North American Rift System (CNARS) provides all excellent setting for major mineral deposits. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending transcurrent fault systems may exercise control over ore forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu. Ni, Co, Ti, Au. Ag and PG-minerals are known to occur in this setting. Arkosic sandstone, siltstone, shale, and minor carbonate units occur on top of the rift basalts and in flunking basins where they may reach thicknesses of 10 km (6 miles). The potential, for stratiform or unconformity-related metalliferous deposits must be considered. The rift as a whole remains, however, largely unexplored.

Jan 1, 1990

By M. S. Celik, G. Onal, S. Atak, A. A. Abramov

An oolitic phosphate ore composed of phosphate (mainly francolite) and carbonates as gangue has been tested for the suitability of the reverse flotation process. The samples were first ground autogeneously followed by the reverse flotation process. While the carbonates were floated by sodium oleate the phosphate was depressed by phosphoric acid. The effect of particle size, reagents type and concentration on flotation recoveries have been investigated to determine the optimum conditions. By this process, a run-of-mine ore containing 16.72 % P205 was upgraded to 28.00% P205 with a recovery of 77.0% The mechanism of optimum flotation with phosphoric acid observed at pH 6.3 is explained based on a relationship involving surface potentials and the ratio of required collector concentrations for the respective minerals.

Jan 1, 1993

By Jianliang Li, Jan M. Mutmansky

This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels.

Jan 1, 1992

By D. Ince

Flotation of dolomite from apatite was investigated, using dodecylamine hydrochloride or sodium oleate as the collector, with and without inorganic modifiers such as sodium chloride. Separation of dolomite from apatite was anticipated from the single mineral experiments under various pH and collector concentration conditions. Flotation selectivity in the mixtures, however, was found to be limited. Attempts to control the flotation response of these minerals by addition of salts such as NaCl and KCI indicated that selectivity is possible. The presence of sodium chloride was determined to depress apatite flotation using sodium oleate, leaving dolomite flotation unaffected (Moudgil and Ince, 1989). In this paper, conditions for optimum separation and the effect of major parameters on the desired selectivity are discussed.

Jan 1, 1992