Search Documents

By A. K. Bakshi, Komar S. Kawatra

A plant trial of a new on-line pressure vessel rheometer for slurries, developed at Michigan Technological University, was carried out at a nearby copper concentrator. The rheometer measured the flow curves (shear stress vs. shear rate) of chalcocite slurries. Viscosity of non-Newtonian slurries changes with shear rate and so, for such slurries viscosity measurement at a single shear rate (often seen in the literature for grinding and classification studies) cannot be correlated to process performance. For these slurries, viscosity at various shear rates can be measured from flow curves generated by the pressure vessel rheometer. Other rheological properties, such as flow type and yield stress can be determined by this rheometer to better characterize the slurries. The slurry at the copper concentrator consisted of ground chalcocite ore. The solids content in the slurry varied between 30-60 % by weight. Top size of the particles was 125 micron, and 80% passing size was 34 micron. Measurements by the pressure vessel rheometer showed that most of the slurries had pseudoplastic flow at shear rates below -3000 sec-l, where the viscosity of the slurry decreased with increase in shear rate. Above -3000 sec-l, like a Newtonian fluid, the viscosity of the slurry remained steady. Flow curves and viscosity from the pressure vessel rheometer were verified with a Brookfield viscometer and a vibrating sphere viscometer, and the results were found to be accurate.

Jan 1, 1997

By Cheryl M. McInnes, Graham J. Sparrow, James T. Woodcock

Three composites, assaying about 3 g/t Au and 0.75% Cu, were investigated. Each contained oxide copper minerals, iron oxides, and silicates. One composite also contained copper and iron sulphides. Maximum gold extractions by thiourea leaching were obtained after copper removal by acid pre¬leaching at pH 1.5 and redox potentials of 400 mV (Pt versus SCE). Best thiourea leaching conditions were pH 1.5, redox potentials over 200 mV, and 0.4% thiourea. This gave 90% gold extraction in 2 h with thiourea consumptions of 25 kg/t. Lower potentials gave poorer extractions. Ferrous iron additions before leaching halved thiourea consumptions. Longer leach times and the presence of sulphide minerals sometimes resulted in reprecipitation of gold.

Jan 1, 1989

By L. Piga, G. Belardi, V. Alesse, N. Shehu, J. Freund

The physico-chemical interactions among minerals such as olivine, chromite and serpentine; the most commonly present ions in solution such as Ca and Mg; and flotation reagents such as EDTA and oleic acid were investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit in Albania. The results were confirmed in beneficiation tests on two ores, one from the Kukes (Kalimash) deposit and the other from the Rizo deposit in Greece. It was demonstrated that, when Na-oleate is used as collector, chromite, olivine and serpentine can be separated at pH 2.5 and/or pH 5.5 when employing ethylenediamine tetraacetate (EDTA) on previously deslimed material. This approach ensures flotation concentrates with a Cr203 content better than 50% with a recovery of more than 75%.

Jan 1, 1998

By J. T. Crawford

A comprehensive strategic-planning model was developed for the phosphate strip-mining and chemical operations at White Springs, FL. The computerized model covers orebody modeling, production simulation and financial analysis. The model has several innovative features, including the use of NPV techniques in orebody block economics, the adaptation of the floating-cone method to a floating template for generating dragline mining units automatically, the use of interactive graphics for designing mining units, and the use of a dragline move economics algorithm for the automatic scheduling of mining-unit assignments and moves. The simulation of chemical-plant production uses linear programming and concentrate inventory levels to control mine-operating schedules.

Jan 1, 1999

By D. E. Ranta, John G. Stone

One of the steps in an ore reserve estimate is customarily a rigorous calculation of the in situ grade of the orebody itself. The result of this calculation is usually reduced by some purely arbitrary factor to force the calculation to agree with the observed grade of ore actually mined. The failure of the calculation to realistically depict the grade of ore actually extracted is in many instances not the result of either an incorrect calculation procedure or of sloppy mining practice, but is a direct consequence of unsuspected irregularities in the contact between the orebody and the surrounding wall rock. A pattern of holes spaced at 1.5-3.Om foot intervals, drilled as part of a pre-development program, will often reveal that a presumed "regular' ore/waste contact is, in fact, so highly irregular that it will be next to impossible to separate ore from waste during mining. In such an instance, 'fingers' of waste projecting into the mining block will substitute for equal volumes of ore left outside the mining limits. As a result, the grade of material actually mined will be less than the grade envisioned for the orebody. The volume of waste substituting for ore in the mining block is about 0.4X, where X = the average error in projecting the ore/waste contact between alternate holes in the test pattern, and is expressed in units of volume per unit of area of the contact surface.

Jan 1, 1992

Jurist, educator and historian Neil Reynolds will be the keynote speaker at the National Mining Hall of Fame's 11th annual induction banquet on Sunday, Oct. 11,1998 at the Pointe Hilton Resort in Phoenix, AZ. Reynolds is Municipal Court Judge for the City of Leadville, CO, home of the National Mining Hall of Fame & Museum, and a fifth-generation resident of the community. His family staked mining claims on nearby Mount Massive in 1862. Judge Reynolds is a fulltime faculty member at Colorado Mountain College, Chairman of the Lake County Historic Preservation Advisory Board and practices law in Leadville. In announcing the speaker, Board Chairman Richard Moolick said seven inductees into the National Mining Hall of Fame will join 138 mining greats previously honored in the annual ceremonies. This year's inductees will be enshrined by Thomas Falkie, president and chief executive officer of Berwind Natural Resources of Philadelphia, PA. Moolick also announced that Jeffrey Clevenger will be the master of ceremonies for the induction banquet. Clevenger is executive vice president of Cyprus Amax Minerals, Englewood, CO and president of Cyprus Climax Metals, Tempe, AZ. A cocktail reception at 6:30 p.m. will precede the black-tie (optional) dinner, to begin at 7:30 p.m. For additional information, contact Esther Mellott at 719 486 1229. Here are the biographies, then, of this year's seven inductees to the National Mining Hall of Fame & Museum.

Jan 1, 1998

By E. Pardo-Igúzquiza

Most mining applications of geostatistical simulation are to the simulation of quantitative variables, such as grade. In many instances the occurrence of quantitative variables and the values they take are controlled, at least partially, by qualitative, or categorical, variables. Examples include quartz-vein controlled gold orebodies and stratigraphic silver/lead/zinc deposits. In these cases a realistic simulation must include geological controls on the spatial distribution of the simulated quantitative variables. This paper describes extensions to, and algorithms for, the truncated plurigausian method of simulating categorical variables. The categorical variables are modelled as indicator random functions that represent the presence/absence of the variable at spatial locations. Stochastic images of the distributions are obtained by truncation of realisations of two Gaussian random functions simulated at the same locations. Parameters required are the thresholds for truncation of the Gaussian variables and the covariance structure of each Gaussian random function. These parameters are estimated from the experimental proportions of each variable and indicator direct and cross semi-variograms. A detailed case study is shown in order to illustrate the procedure, to discuss the results and to present the algorithms for plurigaussian simulation.

Jan 1, 2002

By B. (Manas) Das

Rock characterization for geotechnical purposes using the microhardness technique is discussed in this paper. The concept of rock characterization and its steps are logically developed. The geotechnical properties should be functionally tethered to the technological problems for characterization. The overriding geotechnical concern is rock mass stability. The important factors in this respect are rock properties, structural discontinuities, ground water, field stress, temperature and technological factors. The rock properties are the primary factors and the other factors generally affect rock properties. Of the rock properties the strength and elastic properties can form a basis for rock characterization. The microhardness technique can provide these two properties. Study on coal shows that the microhardness impressions can be used for this purpose. On the basis of this study coals of all ranks can be divided into distinct geotechnical groups. The details of these are discussed in this paper.

Jan 1, 1986

By Conrad G. C. Douglas, Parris A. Lyew-Ayee, Vincent G. Hill

ABSTRACT Distinct patterns are identified in the associations, distributions, and levels of concentration of the silica minerals, boehmite, aluminous goethite, and phosphate minerals in the bauxite deposits of Jamaica. These result from syngenetic and diagenetic reactions associated with post-bauxitization tectonic and associated activities. Three basic types of bauxite are identified, viz., Jamaica-1 (< 3.0% boehmite), Jamaica-2 (> 3.0% boehmite and 30-80% of the iron as aluminous goethites), and Jamaica-3 (> 3.0% boehmite and > 90% of the iron as aluminous goethites). The Jamaica-1 type has a mean value of < 2% boehmite as A1203, while this level in the Jamaica-2 type is usually about 3.5%, and > 4% in the Jamaica-3 type. Similar discrete associations were found for the species and concentrations of aluminous goethite and phosphate minerals. The process and geological implications of these are discussed.

Jan 1, 1984

By C. Ptacek, D. Hiller, J. L. Janbor, H. Mccreadie

Between 1991 and 1994, metallurgical residues from a pressure-oxidation autoclave at the Campbell Au-quartz mine at Red Lake, northern Ontario, were neutralized with dolomite-rich flotation tailings and were deposited in a polyethylene-lined disposal area. Mineralogical analysis indicates that most of the As occurs as a crystalline ferric sulfarsenate, and some is associated with Fe oxides and with K-H3O jarosite. Field pore-water geochemical data from 1994 and 1995 showed increases in Fe(II) and As(III) concentrations, suggesting that the sulfarsenate and jarosite are dissolving; none of the discrete As phases included in a thermodynamic database limit dissolved-As concentrations, and these concentrations may continue to increase. These results demonstrate the potential for Fe and As loading through groundwater systems.

Jan 1, 1998

By D. U. Deere, T. R. Harrell

Factors such as rock cover, rock type and rock quality can exert a dominate influence on the behavior of a concrete tunnel lining. This paper will present and discuss the investigation, evaluation and use of such factors at the Rocky Mountain Pumped Storage Project in the design of the 10.67m (35 foot) diameter concrete tunnel lining. A plane strain, finite element analysis was performed on the concrete/rock system. The finite element model consisted of a concrete lining zone and three (3) rock zones; a highly destressed rock zone, a transitional rock zone and an intact rock zone. Zones were differentiated from one another by varying the modulus for each zone. Results of this study yielded a concrete lining strain from radial expansion which was used in the crack control calculations for the concrete tunnel lining. After the tunnel excavation was performed, plate jacking tests and additional seismic surveys were run on the tunnel walls. This testing served to confirm the rock modulus values used in the preliminary analysis. However, results were observed which indicated that a two zone rock model would more accurately represent in-situ rock conditions than the three-zone rock model used in the preliminary analysis. This revision to the concrete/rock model was made and a final concrete tunnel lining analysis was performed.

Jan 1, 1986

By V. R. Degner

Given: the process tonnage, performance objectives, and plant floor area, the paper will outline the metallurgical and machine hydrodynamic scale-up procedures for translating the lab flotation test results to the design of a full size flotation machine installation, including the machine number, size, and arrangement. Machine selection considerations for rougher, scavenger and cleaner duty, and special considerations relative to specific applications, will be summarized where appropriate. The value of kinetic modeling in quantitative metallurgical (lab to full size machine) scale-up will be reviewed considering a coal installation, and design information for additional applications such as copper, molybdenum, iron, phosphate, and potash will be discussed.

Jan 1, 1986

By R. Y. Wan, J. R. Parga, J. D. Miller

The direct recovery of precious metals from a1kaline cyanide solution is frequently accomplished by the well-established Merrill-Crowe process involving zinc-dust cementation. This is particularly true for silver. Plant data from two operations are presented and analyzed in terms of intrinsic reaction features. In such Merrill-Crowe plants a plate-and-frame filter press acts as a semicontinuous fixed-bed reactor with a distribution of particle retention times. For the plants studied, 99Yo of the silver is recovered with a solution retention time of less than 2 min. Differences in plant operating conditions and product characteristics can be related to the nature of the surface deposit of silver which forms on the zinc particles. From laboratory experiments and plant samples it has been found that the presence of lead in the system activates a change in the silver deposit morphology to the dendritic state which affects the rate of silver deposition as well as the filter cake porosity. Finally the plate-and-frame press is considered from an engineering perspective as a semi- continuous fixed - bed reactor to describe the behavior of the system.

Jan 1, 1987

By M. R. Stokes, A. J. Ross

As a result of higher levels of production and greater depths the underground mining industry in the UK is encountering hotter climates in some workplaces. It is widely known that high heat and humidity in an underground workplace will result in reduced performance and may also seriously impair the health and safety of the workforce. It is therefore of paramount importance that the underground environment can be effectively predicted in order that sound decisions can be made to reduce the effect of climate on working personnel. Over the years numerous computer programs have been developed to predict the climate in underground mines. One such important program, developed by McPherson, is CLlMSlM TM which is a prediction model of heat and mass transfer along a single roadway. This paper describes the development of a computer model, called DRIVE, to predict the climate in single entry drivages. This program incorporates the theory established by McPherson for the development of CLlMSlM TM. This involves the algorithm for unsteady state heat transfer. Throughout the development of DRIVE underground measurements have been taken to correlate the program. DRIVE will predict the changes in psychrometric and thermo- dynamic conditions along the drivage depending on a number of parameters. Firstly, the type of auxiliary ventilation system employed such as forcing, exhausting, overlap. Secondly, the addition of heat and moisture due to autocompression, machinery, strata, fissure water, oxidation, broken rock, fallen rock, refrigeration equipment, lighting, personnel, service water. Thirdly, due to the velocity of the air.

Jan 1, 1997

By R. V. Ramani, S. Tan

In this paper, several commonly used computer truck-dispatching criteria are evaluated. A computer-oriented truck-dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. However, several dispatching criteria that have good potential to increase performance can be identified. All basic dispatching criteria, including minimizing truck waiting time, waiting shovel with minimum waiting time, minimizing truck saturation, maximizing truck momentary productivity or optimization of truck routes, provide local optimal solutions. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. It may be necessary to search for a hybrid combination of the several truck dispatching criteria that have good potential for a given situation. An approach to selecting such a hybrid dispatching criterion is presented.

Jan 1, 1993

By Y. C. Kim, W. L. Meyer, W. Cai

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the US has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms. This paper compares the performance of the floating cone algorithm with the rigorous optimization algorithm of the Lerchs-Grossman&apos;s graph theory and the newly developed maximum network flow algorithm by Hanson (1986). The maximum flow algorithm is a modified version of the logic as initially advocated by Johnson in 1968. Comparisons are made for three different deposits in terms of the total profits generated and the computation times involved. The results of the comparison show that both algorithms produced higher total profitability pits than the floating cone in all three deposits, although the increase in profits never exceeded 1 % of the base design obtained using the floating cone. Between the graph theory and maximum flow, graph theory produced consistently higher profits. The current version of maximum flow, however, cannot be modified to produce the optimum pit. Nevertheless, the authors prefer the maximum flow over the graph theory, simply because it is easy to program as well as to explain.

Jan 1, 1987

By B. R. Reddy, P. V. R. Bhaskara Sarma

A process for the separation and recovery of cobalt and nickel was optimized for a sulfate leach solution of Indian Ocean sea nodules containing 80 g/m3 cobalt and 730 g/m3 nickel using the sodium salt of Cyanex 272 as the extractant. Extraction of both cobalt and nickel increased with an increase in equilibrium pH and extractant concentration. The extracted species with respect to cobalt appears to be CoA2.3HA. More than 99.6% extraction of cobalt was achieved using 0.04M solvent in a three-stage counter current simulation at the A:O phase ratio of 3:2. The co-extraction of nickel was about 0.6% only. Two-stage countercurrent stripping of cobalt from the loaded organic at an A:O ratio of 1: 7 resulted in a pregnant electrolyte enriched by 0.8 kg/m3, thus enabling a ten times overall enrichment of cobalt. From the cobalt free raffinate, nickel extraction was carried out using 0.25M solvent in two countercurrent stages, and the extraction showed a 99.8% recovery. Stripping of nickel from the loaded solvent was carried out at an equal phase ratio with the advance electrolyte of pH 1.75 in two countercurrent stages. The nickel stripping efficiency was found to be 98.8%. The present studies indicated that complete recovery of cobalt and nickel was possible using nine counter-current stages.

Jan 1, 2002

By Adrian Brown

Groundwater inflow and impacts have become major aspects in the permitting and operation of many gold mines. First, the hydrothermal or placer genesis of many of the orebodies being investigated or produced today almost guarantees that mines will be "wet", involving groundwater control as part of operations. Second, the style of ore deposition a1 so often involves a1teration of the host rock, resulting in relatively weak, low permeabi1ity materials that require extensive groundwater pressure control for stable mining. Third, the location of many mines in arid areas guarantees that impacts on water resources will be matters of key focus during permitting and operation. However, groundwater control and protection is a technically difficult area and often involves managerial decisions and activities that do not fit comfortably into traditional mining. In an attempt to overcome some of these difficulties, this paper provides a guide to mine managers and hydrologists as to appropriate strategies for designing, setting up, operating, and evaluating groundwater programs at gold mines that get the job done and are cost effective.

Jan 1, 1988

By Maurice C. Fuerstenau, Bruce R. Palmer, R. E. Johnson, B. R. Palmer, G. W. Warren

The environmentally sound processing of metal-bearing chloride solutions plays a key role in the extraction, plating, recycling, finishing and surface preparation of metals. Additionally, many chloride-bearing waste streams must be processed to obtain environmentally acceptable products. This paper reviews the technologies used for processing aqueous metal-chloride solutions and describes the challenges that have been overcome in application of these technologies.

Jan 1, 1993

By Charles P. Lazzara, Alex C. Smith, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to evaluate the effect of ventilation on the performance of automatic sprinkler systems in extinguishing wood crib fires. Experiments were conducted at airflows of 0, 0.76, 1.5, 2.5, and 4.1 m/s. Two experiments were conducted at each airflow, using 74° C fast response pendent sprinklers in one experiment and 74° C fast response horizontal sidewall sprinklers in the other experiment. In the experiments at airflows of 0 and 0.76 m/s, sprinklers were located directly above the fire and 2.4 m upstream and downstream of the fire. The sprinkler directly above the fire was the only sprinkler to operate with no discernible difference in the suppression capability of the pendent and horizontal sidewall sprinklers. In the experiments at airflows of 1.5 and 2.5 m/s, sprinklers were located directly above the fire and 2.4 and 4.8 m downstream of the fire. The sprinkler located 2.4 m downstream was the only sprinkler to operate with the horizontal sidewall sprinkler being more effective in extinguishing the wood crib fire. The average response times of the sprinklers at airflows of 0.76, 1.5, and 2.5 m/s were 3-1/2 times the average response time of the sprinklers at 0 m/s. The results of this study will help enhance the safety of the nation&apos;s miners.

Jan 1, 1993