Search Documents

By C. P. Lazzara, F. J. Perzak, C. C. Hwang, C. D. Litton

Fire development and spread along conveyor belts in ventilated ducts were investigated experimentally and theoretically. Various types of conveyor belts used in mining applications were ignited and burned in a full-scale gallery under various flow conditions. The flame spread rates depended strongly on the ventilation air speed. The time-temperature traces of gas and belt obtained at 12 feet from the entrance show that a rapid belt surface temperature change takes place prior to a change in the gas temperature, indicating that radiative heat transfer from the flame to the belt surface plays an important role. Further, anomalies in the flame spread rate in the vicinity of 1.5 m/s air speed (i.e., much greater rate than that observed at either higher or lower speeds) can be explained through the mechanism of flame tilt and the resultant view factor between the flame surface and the belt surface. In order to correlate the fire spread with material properties of the conveyor belts (such as the specific heat, the thermal conductivity, and the pyrolysis temperature) and the fire environment (such as the gas temperature and the ventilation air speed), a theoretical model has been developed. This model is based on the experimental observation that the radiative heat transfer is the dominant mode of energy transfer ahead of the flame front. Agreement between the theory and the experimental results is good.

Jan 1, 1991

By Ora H. Rostad

Veins containing silver and gold values, with some associated values in copper, lead, and zinc, were discovered in 1890 by Will Kirwin in what was later designated the Kirwin mining district situated on the North Fork of the Wood River, about 56 km (35 miles) west of Meeteetse. (See Fig. I.) After considerable prospecting activity, including the driving of several short adits on veins, most of theclaims in the district were consolidated into two ownerships. One was held by the Galena Ridge Mining Co. which was organized on Nov. 18, 1902. The other was held by the Shoshone Mountain Mining Co. which was organized on Mar. 23, 1903. During the period from 1903 to 1907 inclusive, the two companies continued exploration on veins in their respective areas. The major exploration-development activity for the Galena Ridge Mining Co. was the driving of the Galena Ridge crosscut adit for 709 m (2327 ft), to cut veins at depth which had been explored by short adits high on Galena Ridge. Shoshone Mountain Mining Co. concentrated their work on the Bryan and Pickwick veins. Neither of the companies found ore that was rich enough to sustain profitable operations in that remote locality. Most of the major exploration and development activities were stopped in late 1907. A major snowslide in February 1907 killed three people and destroyed several buildings and may have contributed to discouragement in the area. From 1908 to the early 1920s, only minor exploration work was done. Galena Ridge Mining Co. was dissolved Aug. 5, 1922, and Shoshone Mountain Mining Co. was dissolved on Mar. 23, 1923.

Jan 1, 1991

By K. V. S. Sastry, A. J. Hunt, K. D. Lofftus

Sol-gel processing is rapidly becoming an important process for producing such advanced materials as high activity catalysts, fiber optics and ceramic precursors. These materials can be tailor made with properties unique to sol particles as well as the gel aggregates by controlling production of the sol, the formation of the gel, and the removal of the interstitial fluids. This paper presents colloidal and kinetic principles of sol generation and gel formation. Hydrolysis of alkoxides provides the best means of controlling sol production and electrostatic stabilization enables the formation of the most homogeneous gels. Gelation occurs by hierarchial aggregation which produces inhomogeneities much larger than the sol particles. Colloidal and kinetic principles can be applied to reduce the size of the inhomogeneities and obtain high performance transparent insulation and new ceramic composites.

Jan 1, 1990

By R. L. Wiegel, G. R. Oswald

The processors of Florida phosphate rock face constraints similar to those of other mineral operations--leaner ore, more complex treatment schemes and a product which sells for a penny a pound. IMC Fertilizer is a dominant producer in this market with its current operation of five processing plants. An emphasis by their management in maintaining and improving plant performance has continued unabated for some 15 years. This has resulted in a commitment to the importance of routine automatic sampling of product and in process streams, the generation of reliable assay and size distribution data, the accurate measurement of process flows, and the computerized "rendering" of this information into weekly and monthly material balances which provide consistent measures of process performance. In addition, there has been a parallel program to monitor and improve the performance of flotation reagents and to evaluate process modifications or changes in equipment. This paper will describe the evaluation techniques that have evolved over this period and indicate how the historical data base is used to identify plant problems early and help in their solution.

Jan 1, 1991

By Serkan Saydam, Ercument Yalcin

This paper presents the results of Caldagi Nickel-Cobalt Ore Deposit's, located in Turkey, reserve and ultimate pit limit design analysis. Reserve analysis of any deposit requires two steps. First one is to constitute of block model of the deposit and second step is to generate ultimate pit limit. The block model of the Caldagi ore deposit has been created by means of geostatistics. The reserves of nickel and cobalt in this block model are defined as resource, approximately 12 million tons of nickel and 1 million tons of cobalt with average grades of 0.9% Ni and 0.03% Co, respectively. Ultimate pit limit analysis has been performed by considering economic, technical and legal factors. In this paper, the ultimate pit limits are generated by Lerchs & Grossmann (L&G) algorithm. As a consequence of ultimate pit limit design, total amount of tonnage to be excavated is 1.4 billions of tons, 700 million of which contains ore and 747 million of which is the tonnage of waste.

Jan 1, 2002

By Randhir Sehgal

If the primary purpose of a control system is to assure a fixed-quality product at maximum yield, the real issue involved in control of the fine coal cleaning circuit in a plant is to demonstrate that control is technically feasible and economically beneficial . This paper suggests that it is not easy to do so in most cases. Fine coal, defined here as the 28 mesh x 0 fraction of the plant feed, is generally cleaned using a combination of hydrocyclones and flotation. Both of these processes are relatively insensitive to changes in operating variables. Further, the fines fraction general 1 y forms no more than 20% of the plant feed and, at times, is as low as 10%. The instruments to measure flow rates, densities, and product qua1ity (ash, sulfur, etc.) are not sufficiently accurate to allow effective responses to changing state variables and product quality. It is sufficient to run the fine coal circuits at maximum recovery, and the control of product quality and optimization of yield should be achieved by controlling the coarse coal circuits and measuring the quality of the entire clean coal leaving the plant. This contention is made with particular reference to U.S. plants cleaning coal for the utility industry and should be viewed in this context only. It is explicitly admitted that this strategy is mathematically non-optimal in the sense that all size fractions are not necessarily cleaned at equal elementary ash, and would result in a loss of yield. However, under the conditions of conventional coal cleaning practice, this is a sensible approach.

Jan 1, 1988

By Jack S. McPartland, Gene E. McClelland

It is advisable, for any heap leach project, to develop an historical metallurgical data base to predict production heap performance before ore is mined and placed onto the heap. A data base would include results from: interval assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples; and those results plus column leach test data on diamond drill core or bulk ore composites. Subsequent larger scale heap leach test data can then be compared to the historical data base, to blast hole composite data during mining, and eventually to production data. This paper does not discuss metallurgical comparisons between assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples, but does discuss metallurgical comparisons from bottle roll tests, laboratory scale column leach tests, and pilot scale heap leach tests on core and bulk ore samples with operating data for three U.S. commercially producing heap leach operations. Provided that representative core or bulk samples are used for evaluation, heap leach test results accurately predict or understate the success of the commercial operation and remove most of the uncertainty from the investment decision.

Jan 1, 1990

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation was investigated as a process to convert gaseous CO2, into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results were achieved using heat-pretreated serpentine feed material and a high partial pressure of CO2 (Pc02). Specific conditions include 155°C, PC02 = 185 atm and 15% solids. Under these conditions, a 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy was utilized to investigate the appropriate feed characteristics, identify the process products and interpret the mineral dissolution and carbonate precipitation reaction paths. Key words: Mineral carbonation, Carbon dioxide sequestration, Carbonates

Jan 1, 2003

By M. Rîsteiu

The authors aim to analyze the behavior of smart sensors using Transmission Control Protocol/Internet Protocol (TCP/IP) infrastructure in hazardous applications, because of their advantages regarding safety, expansion and Quality of Service (QoS). Initially, some constraints are discussed for these applications. Then, the possibility is analyzed of using 2.4 GHz TCP/IP based transmission for sending data out of an industrial area. In this setup the authors evaluated the round-trip implementation (which requires a database of packet lengths), related to the delay introduced by the radio transmission algorithms from 802.15.4, and 802.11d/g protocols. Tuning results of different varying time-delays were compared to the constant delay cases from the literature (Deák, 2003; Lincoln, 2003). Both the hardware and software setups are implemented. Based on TinyOS specific software for hardware checking/ initiating communication/ starting/ closing measurements the authors have developed separate/combined procedures for testing the integrated devices. Measured time delay is presented and analyzed, for both beaconed and non-beaconed 802.15.4 transmission, with power optimization criteria. By testing two different implementations (Zhang et al., 2001), (ATmega256 RZAV - 256KB flash memory, the CC2420 IEEE 802.15.4 and ZigBee-compliant RF transceiver core - 128KB flash memory) the authors have found some time delay variations as a result of local processing by the ZigBee controller with an amount of flash memory. The work is also focused on adapting industrial measuring standard systems to the smart sensors, but not only through the 4-20 mA standard.

Jan 1, 2008

By Ronald I. Fuller

Core Laboratories, a division of Western Atlas International, maintains laboratories in all energy-producing areas of the United States, as well as in many foreign countries. Central to laboratory operations has been the incorporation of computers and computer software. Core has developed a mu1tiuser Laboratory Information Management System (LIMS) , which is currently installed in numerous company sites in the U.S., and is now undergoing installation in Canada. In addition, Core has provided custom soft ware to contract laboratories which Core operates on behalf of mining firms. The software development was done under the direction of the author in Denver, Colorado, and Casper, Wyoming. The intent of this paper is to pass some of the practical experience gained by our efforts on to those who wish to utilize computers more fully in the laboratory setting. The product of analytical laboratories is numbers. Nothing else comes from our work. We deal in information about samples. It is then reasonable to assume that the computer would be central to a laboratory operation. The hard part is to initially define what kind of computer the lab operation needs. The choices today can be very complex, and almost every hardware salesman is full of bad advice. Even the people in your own information services department may hold divided opinions. Since the advent of the personal computer, we have lived with a polarized data processing community. The PC boys consider their machines equal to any challenge, while the "save the mainframe" crowd view the PCs as limited toys that are only good for the things that clutter up a real computer. Management tends to lean toward whatever costs the least.

Jan 1, 1989

By S. Kelkar, H. Murphy, Z. Dash

Nearly 30 estimates of the minimum earth stress were obtained from hydraulic stimulation tests in 5 boreholes at depths varying from 0.6 to 4.3 km in jointed granitic rock near the Valles Caldera in New Mexico. This site is located within the transition between the Colorado Plateau and Basin and Range provinces. Stresses were determined from open hole hydraulic fracturing experiments conducted with water at pressures up to 48.3 MPa (surface). The virgin bottomhol e temperatures ranged up to 327°C. Pressure records show no evidence of rock breakdown, indicating injection into pre-existing joints. A typical pressure response consists of an early wellbore storage period followed by linear fracture flow, which then evolves into a steady pressure, fracture extension mode. Shut-in behavior is characterized by a sharp pressure drop followed by a more gradual decay. The minimum earth stress shows a general linear trend with depth, increasing with a gradient of 19 MPa/km. A low stress anomaly occurs from 2490 to 3100 m where the minimum stresses are as much as 28 MPa lower.

Jan 1, 1986

By Yuuichi Umeki, Yuusaku Tominaga

In order to keep good air condition in any specific branch such as coal face and/or heading in an underground coal mine, effective factors of all the branches with respect to the specified branch have been investigated, using computer simulation. Main results of the paper are as follows; 1) A branch in a network is classified to one of three classes of effectiveness to increase, to decrease and not to change airflow rate in the specific branch by altering aerodynamic resistance in the branch. 2) Distribution of position of branches, belonging to each class, related to a specific branch is one of the macroscopic characteristic of a network which is the inherent property of every network. 3) A relation of the aerodynamic resistances of any two branches to keep a constant airflow rate in the specified branch is shown as a monotonous curve. 4) Ventilation transition diagram with the rate of airflow in the two branches as coordinates, and for different rates of airflow in the specific branch as the parameter, is found to be straight lines. 5) Existing range of airflow rates In the specified branch is given as a parameter in the enclosed area in the ventilation transition diagram. Moreover, an expert system to assist ventilation control using a transition diagram of airflow rate is introduced in this paper.

Jan 1, 1991

By J. A. Frew, R. M. Glen

Recovery of galena and sphalerite from fine grained lead-zinc ores by flotation normally requires re-grinding to achieve economic recoveries at acceptable concentrate grades. Re-grinding aims to reduce the coarse valuable mineral particles to a size where they float more readily and to liberate the composite valuable particles so that the gangue in these composites does not dilute the concentrate. Besides changing particle size and liberation, re-grinding changes the surfaces of the minerals and thus may alter the rate that mineral particles of a given size and liberation float. A method was developed to apportion the total change in recovery after re-grinding between changes in size and liberation and changes in flotation rates. The flotation behaviour of minerals, before and after re-grinding, was measured by floating samples of plant streams under controlled conditions in a laboratory cell. Results from several industrial lead-zinc circuits indicated that the change in behaviour observed fell into three different categories. It is concluded that the method will indicate whether the focus for optimization of existing plant should be on comminution or flotation, and it will help determine the path for laboratory testing in designing new regrind circuits.

Jan 1, 1995

By Michael L. Nave

Belt Conveyors are an important method for transportation of bulk materials in the mining industry. The control of the application of the starting torque from the belt drive system to the belt fabric affects the performance, life cost, and reliability of the conveyor. This paper examines applications of each starting method within the coal mining industry.

Jan 1, 1993

By Mortimer J. Richardson

Dredging can be traced to early times where it may have been derived by the Phoenicians prior to the 4th century B.C. The first tangible design drawings of a bucket ladder (BL) dredge can be found in the collections of Leonardo da Vinci (1452-1519), which he produced when he was attempting to create better methods of channel and port dredging. The perfection of the system did not commence until after the invention of the steam engine in the early 1800's; providing the impetus to progress from man-powered mud mills, horse drawn along polders or dikes in the Netherlands, England, France and Germany, to steam-driven. In the 1860's following the various gold rushes in the U.S., Australia, New Zealand, Siberia and South America, with placers in particular, efforts were begun to apply mechanization to achieve deeper digging. There is a recording of a dredge being installed to mine gold in Montana in the 1860's but did not include a processing system. Then in the 1880's in New Zealand, some practical engineers developed a system that is said to be the first bucket ladder mining (BL/M) dredge for mining gold placers. In studies of the New Zealand gold dredging experience, it is estimated that some 500 dredges were built to mine gold between the 1880's and 1942. A careful analysis of the data, however, shows that very few were profitable. The technology appeared to stagnate in the early part of the century. Two of the BL/M dredge design engineers left New

Jan 1, 1992

By Kirk H. P. E. McDaniel, Mark T. Strever, Keith G. Jr. Wallace

This paper presents the design and installation of an underground ventilation remote monitoring and control system at the Waste Isolation Pilot Plant. This facility is designed to demonstrate safe underground disposal of U.S. defense generated transuranic nuclear waste. To improve the operability of the ventilation system, an underground remote monitoring and control system was designed and installed. The system consists of 15 air velocity sensors and 8 differential pressure sensors strategically located throughout the underground facility providing real-time data regarding the status of the ventilation system. In addition, a control system was installed on the main underground air regulators. The regulator control system gives indication of the regulator position and can be controlled either locally or remotely. The sensor output is displayed locally and at a central surface location through the site-wide Central Monitoring System (CMS). The CMS operator can review all sensor data and can remotely operate the main underground regulators. Furthermore, the Virtual Address Extension (VAX) network allows the ventilation engineer to retrieve real-time ventilation data on his personal computer located in his workstation. This paper describes the types of sensors selected, the installation of the instrumentation, and the initial operation of the remote monitoring system.

Jan 1, 1995

By Raj K. Rajamani, Poly K. Songfack

The slurry transport within the ball mill greatly influences the mill holdup, residence time, breakage rate, and hence the power draw and the particle size distribution of the mill product. However, residence-time distribution and holdup in industrial mills could not be predicted a priori. Indeed, it is impossible to determine the slurry loading in continuously operating mills by direct measurement, especially in industrial mills. In this paper, the slurry transport problem is solved using the principles of fluid mechanics. First, the motion of the ball charge and its expansion are predicted by a technique called discrete element method. Then the slurry flow through the porous ball charge is tackled with a fluid-flow technique called the marker and cell method. This may be the only numerical technique capable of tracking the slurry- free surface as it fluctuates with the motion of the ball charge. The result is a prediction of the slurry profile in both the radial and axial directions. Hence, it leads to the detailed description of slurry mass and ball charge within the mill. The model predictions are verified with pilot-scale experimental work. This novel approach based on the physics of fluid flow is devoid of any empiricism. It is shown that the holdup of industrial mills at a given feed percent solids can be predicted successfully.

Jan 1, 1995

By John Nadolski

Intensive hydrologic monitoring of the Powder river basin has been on-going since the early 1970's. Data were used in environ- mental assessments and for determination of hydrologic consequences associated with coal mining activities. For most coal mine operators, data collection has continued in this baseline mode with little or no statistical analysis of the data and with no statistical procedure established to detect changes in groundwater quality. For the past four years Powder River Coal Company has studied several statistical techniques to analyze groundwater quality. Three objectives were pursued: 1) to determine the baseline water quality for key aquifers; 2) to determine which wells could be deleted from the monitoring program without reducing monitoring effectiveness; and 3) to define a statistical test to determine water quality changes. Knowledge of the regional geo-hydrologic system was combined with an analysis of the water quality monitoring in order to identify homogeneous aquifer zones. All wells within an aquifer zone were treated as one population, and a t-test was used to determine the minimum number of samples needed to define the water quality for each aquifer zone. Results indicate that the data for each aquifer zone were nor- mally distributed and that groundwater quality could be defined using a fairly small number of samples. Because of the minimum sample size test, groundwater quality sampling was reduced by between 75 and 85 percent.

Jan 1, 1989

By Andrzej Wala, Tom Altman, Tom Hughes

The University of Kentucky Mine Ventilation Manager (UKMVM) is a system that contains Level Five knowledge bases and comprises an expert mine ventilation management system. The package uses production rule language (PRL) to interpret data monitored from sensors, e.g., for airflow, temperature, and concentration of gases, in an underground mining environment. Activated from the PRL knowledge bases are Pascal subprograms which (1) organize the monitored data to set up emergency consultations, (2) display graphic representations of a mine's ventilation network with the latest sensor readings, (3) provide interactive updating of mine ventilation parameters, e.g., resistance changes, revised flow requirements, and new regulator and fan settings. Also activated from these knowledge bases are programs which (1) monitor airflow, temperature and gas concentrations from a physical mine ventilation model and (2) adjust regulator openings and fan rpm's. Thus, as an expert system the UKMVM not only presents advisory consultations for underground environmental emergencies, but also serves as an interface between the monitoring and responsive control aspects in the continuous maintenance of normal mine ventilation.

Jan 1, 1989

By W. A. Heitbrink, M. Schmitz, J. A. Organiscak, A. B. Cecala, E. Ahrenholtz

Mobile excavation equipment operators at surface mines generally have the highest exposure to airborne respirable silica dust. Operator cabs on newer equipment are usually enclosed and equipped with heating and air conditioning systems. Many newer cabs are also equipped with air filtration systems. However, some newer cabs and many older cabs have either inefficient or no air filtration systems. The U. S. surface mining industry is still populated with older equipment and many of these have cabs that provide little or no respirable silica dust protection. Collaborative field studies were conducted as part of a partnership involving NIOSH, Clean Air Filter®, Red Dot, MSHA, and several mine operators to demonstrate that effective dust protection can be provided by these cabs at a nominal cost to mine operators. This effort encompassed adding an external make-up air fan and filter system to a retrofitted roof-mounted heating and air conditioning system in three older equipment cabs, and attempting to seal the cab enclosures to achieve interior cab pressurization. Abetter than 90 percent dust reduction was measured inside two of the three enclosed equipment cabs. It was possible to achieve positive cab pressurization inside these two cabs. A less significant dust reduction was measured inside the third cab, where positive pressurization was not achieved. These field studies demonstrate the key elements needed to improve enclosed cab dust protection in a cost-effective manner.

Jan 1, 2003